YTH348 Part's Manual Gasoline containing up to 0% ethanol (E0) is acceptable for use in this machine. The use of any gasoline exceeding 0% ethanol (E0) will void the product warranty. 53 43 08-90 Rev. 4
SCHEMATIC SCH A AMMETER (OPTIONAL) RED FUSE BATTERY RED SOLENOID STARTER M WHITE PTO SWITCH (DISENGAGED) WHITE ELECTRIC CLUTCH S B M A G L A RED C A H D WHITE RED CLUTCH/BRAKE (PEDAL UP) GRAY B E REVERSE SWITCH (NOT IN REVERSE) 3 SEAT SWITCH (NOT OCCUPIED) 6 GRAY /WHITE JUNCTION CONNECTOR CHASSIS HARNESS SHORTING CONNECTOR C B A F E D H G BLUE IGNITION UNIT (OPTIONAL) HOUR METER SPARK PLUGS GAP ( PLUGS ON TWIN CYL. ENGINES) PTO SWITCH (MATING SIDE) BLUE FUEL LINE BLUE V POWER OUTLET (OPTIONAL) NOTES ORANGE FUEL SHUT-OFF SOLENOID (IF EQUIPPED) RED CHARGING SYSTEM OUTPUT 9-6AMPDC@3600 RPM REGULATOR STATOR 8 VOLTS AC @ 3600 RPM (REGULATOR DISCONNECTED) BROWN LIGHT SWITCH HEADLIGHTS IGNITION SWITCH POSITION CIRCUIT MAKE OFF RUN/OVERRIDE RUN M+G+A B+A B+A L+A START B+S+A 3 CHASSIS HARNESS CONNECTOR (MATING SIDE) 6 5 4 6 5 4 3 DASH HARNESS CONNECTOR WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING. NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS 9
ELECTRICAL TS 90 30 33 7 79 9 4 8 99 00 34 7 4 43 4 6 40 5 8 55 6 With V Outlet Option 03 7 59 0 9 With Service Minder Option 05 46 30
ELECTRICAL 53 6 34-65 Battery 874 76 04- Bolt Hex Hd /4-0 unc x 3/4 8 53 4 4-5 Battery Tray 6 53 7 6-38 Switch Interlock 53 8 37-59 Harness Socket Light 53 00 4-5 Bulb, Light #56 4 53 40 0-53 Cable Battery 5 53 4 8-95 Cable Starter 6 53 7 5-58 Fuse 7 873 5 04-00 Nut Keps Hex /4-0 unc 8 53 4 54-9 Cable Ground " Blk 6 Ga. 9 53 40 5-45 Switch Seat 30 53 9 33-50 Switch Ign 33 53 4 9-33 Key/Chain 34 53 07- Switch Light/Reset 40 53 40-04 Harness Ign. Dash 4 87 7 04-08 Screw Thd Cut /4-0 x / 4 53 3 5-63 Cover Terminal Red 43 53 9 5-07 Solenoid 46 53 40 7-63 Gauge Hourmeter 50 53 9 6- Switch PTO 55 87 06 05- Screw Thdrol 5/6-8 x 3/4 7 53 9 4-76 Harness Ign 79 53 7 5-4 Socket Asm. Bulb Twistlock 90 53 40 07-4 Cover Terminal Battery 9 53 9 0-70 Strap Battery 99 87 67 04- Screw Hexwsh Thdrol /4-0 x 3/4 00 89 09 4-6 Washer 9/3 x 7/8 x 6 Ga. 0 53 40 44-54 Harness Pigtail 05 53 40 75-68 Switch Reverse TT Pedal Control NOTE: All component dimensions given in U.S. inches inch = 5.4 mm 3
CHASSIS AND ENCLOSURES 39 3 38 86 83 84 99 6 36 85 94 36 94 37 8 87 6 8 3
CHASSIS AND ENCLOSURES 3 53 40 50- Logo 5 53 44 84-4 Dash 4 53 4 0-46 Hood 5 53 9 89-07 Lens LH 8 53 40 86-07 Grille Asm. 5 53 9 89-06 Lens RH 34 53 9 6-5 Plate Engine 36 87 06 05- Screw 5/6-8 x 3/4 37 53 44-78 Fender 5 873 68 05-00 Nut Lock 5/6-8 68 87 49 05-08 Screw 5/6-8 x / 30 53 4 63-58 Screw #0 x 0.750 BOS Thread 37 53 40 75-90 Bumper Dash 50 53 9 85- Air Duct 5 53 9 95-35 Shield Browning 6 53 40 96-7 Window Fuel 6 53 4 4-3 Screw 65 53 9 68-6 Support Tank Rear 75 53 9 63-04 Crossmember 76 53 40 07-76 Screw 0-4 x 5/8 77 53 9 5-7 Bushing Steering 80 53 9 54-57 Chassis 8 53 40 30-5 Bushing Mtg. Fender Crgo 8 53 40 68-59 Dash Lower 83 874 5 05-0 Bolt 5/6-8 x -/4 Full Thd. 89 87 00 05- Screw 5/6-8 x 3/4 94 873 90 05-00 Nut Lock Hex Flange 5/6-8 95 53 40 4-37 Plug Hole Dash Lower 99 53 4 34-85 Plate Deck Lift 0 53 40 30-48 Vent Side Hood RH 03 53 40 30-76 Vent Side Hood LH 04 53 4 66-3 Vent Top Hood 05 53 40 7-09 Skirt Hood Side RH 06 53 40 7- Skirt Hood Side LH 07 53 9 7-98 Bezel RH 08 53 9 7-99 Bezel LH 09 53 9 9-30 Insert Hex Top RH 0 53 9 9-3 Insert Hex Top LH 53 9 9-3 Insert Hex Bottom RH 53 9 9-33 Insert Hex Bottom LH 3 874 76 05- Bolt 5/6-8 unc x 3/4 4 53 9 9-45 Clip Retainer Tinner 7 53 40 9-67 Rod Pivot 8 53 9 63-95 X-Piece Hood Stop 8 53 9 5-6 Stud Fastner 33 53 9 65-39 Bolt, Shoulder 34 53 40 47-4 Bumper Hood 35 53 40 6-9 Spacer Fender 36 873 93 05-00 Nut Lock 5/6-8 unc 38 53 40 86-06 Trim 39 53 04-5 Nut, Push 8 53 4 4-0 Clip Retainer Console 83 53 4 87-4 Console Asm. Decklift 84 53 4 78-87 Console Asm. 85 53 4 63-5 Console Insert RH 86 53 4 63-7 Console Insert LH 87 87 60 04-06 Screw Hex Washead /4-0 x 3/8 NOTE: All component dimensions given in U.S. inches inch = 5.4 mm 33
DRIVE 3 07 9 06 5 6 56 09 60 6 43 6 7 84 97 96 4 35 70 5 5 80 5 5 64 67 5 49 59 85 86 89 87 88 60 6 5 63 6 53 5 08 5 4 0 50 5 9 5 66 5 90 5 5 33 30 05 drive-tex_k46_pedal_8_r 59 7 53 83 6 5 6 83 05 73 33 99 73 30 34
DRIVE - - - - - - - - - Transaxle, TUFFTORQ K46 BT (Internal parts not available) 53 35-83 Key 5 89 3 3-6 Washer 3/3 x 3/6 x 6 Ga. 7 53 4 36-78 Spring, Brake 6 53 9 96-79 Spring Return Cruise 9 53 40 38-06 Rod, Brake 33 8 00 00-0 Ring E 35 53 9 95-9 Rod, Brake, Park 4 53 48-7 Cover, Foot Pedal 49 87 06-4 Bolt 50 53 9 43-7 Pulley Idler Flat 5 873 90 06-00 Lock Nut 3/8-6 5 53 9 43-6 Idler V-Groove 90" Offset 56 53 3 09-69 V-Belt, Drive 64 53 9 78-65 Shaft Asm. Pedal Brake Control 73 874 49 05-44 Bolt Hex Flghd 5/6-8 Gr. 5 80 53 4 00-4 Strap Torque 9 874 76 05-0 Bolt Fin Hex 5/6-8 unc x.5 99 53 4 57-4 Rod Asm. Bypass 6 873 90 05-00 Nut Lock Hex Flange 5/6-8 5 87 00 05- Screw 5/6-8 x 3/4 43 87 49 05-08 Screw 5/6-8 x / 53 53 47-88 Retainer Spring 59 876 0 04- Pin Cotter /8 x 3/4 60 53 6 94-84 Retainer Clip 6 53 0 57-09 Spring, Return, Clutch 63 53 40 0-34 Rod Pedal Control 66 53 4 83-05 Nut Push 67 53 40 5-57 Latch Brake Parking 70 53 9 43- Keeper Belt Centerspan 7 87 06-6 Bolt RDHD SQNK 3/8-6 unc x 83 53 3 70-57 Spacer Split 84 53 40 3-8 Handle Parking Brake 85 87 06- Bolt Rdhd Sqnk 3/8-6 x -3/4 Gr. 5 86 53 9 43- Spacer Retainer 87 89 3 3-0 Washer 88 53 9 43-3 Link Clutch Ground Drive 89 53 9 43-7 Bellcrank Ground Drive 90 53 9 43-8 Keeper Bellcrank Ground Drive 96 87 00 06-6 Screw 3/8-6 x 97 53 9 58-04 Bracket Clutch Anti-Rotation 05 53 7-48 Washer 06 53 9 78-67 Bracket Mount Latch Cruise 07 53 9 78-68 Latch Control Cruise 08 53 9 78-69 Gear Sector Control Cruise 09 53 9 95-9 Rod Control Cruise 0 53 40 09-80 Rocker Asm. Pedal Control 53 0-83 Bearing Nylon 3 53 40 3-9 Knob Control Cruise 4 53 4-63 Pedal Forward Pad 5 53 40 7-3 Pedal Reverse 6 53 9 6-3 Bracket Pulley Idler 53 40 3-87 Retainer Spring Clip Handle 879 0-0 Washer /3 x -/4 x 0 Ga. 5 53 40 33-9 Keeper Belt Trans. 6 53 40 5-64 Bracket Mount Torque 30 53 8 89-67 Washer Hardened NOTE: All component dimensions given in U.S. inches inch = 5.4 mm 35
ENGINE 6 87 0 69 9 45 7 8 37 5 8 37 8 84 8 8 79 70 3 09 4 4 9 0 90 85 9 SPARK ARRESTER KIT engine-tex_bs-cyl_53 36
ENGINE - - - - - - Engine Briggs Model No. 445577-87-G 53 4 97-3 Muffler 9 53 9 43-0 Keeper Belt Engine 53 40 00-08 Clutch Electric 53 40 50-97 Pulley Engine 5 53 4 4-5 Tank Fuel 8 53 43 0-3 Cap Asm 0 53 4 35-0 Control Throttle/Choke 53 4 63-58 Screw #0 x 0.750 BOS Thread 8 53 40-35 Fuel Line 9 53 3 7-80 Spark Arrester Kit 37 53 34-87 Clamp Hose 4 53 6-97 Washer -/ OD x 5/3 ID x.50 4 80 04 07-00 Washer Lock 7/6 45 873 5 04-00 Nut Keps Hex /4-0 unc 6 53 4 66-9 Shield Heat Muffler 69 53 6 53-9 Gasket 70 53 5 99-55 Tube Exhaust LH 7 53 6 05-89 Tube Exhaust RH 79 53 8 39-06 Screw Socket Head 5/6-8 x 8 53 4 84-56 Tube Drain Oil Easy 8 53 4 8-87 Drain Oil Valve 84 87 06 06-0 Screw 3/8-6 x -/4 85 53 7 39-37 Bolt Hex 7/6-0 x 4 Gr. 5 87 53 7 8-77 Bolt 5/6-8 unc x w/sems 90 87 00 06-6 Screw 3/8-6 x 9 53 8 74-95 Bushing.375 OD 09 53 4 4-4 Canister Carbon Filter Asm. 0 53 4 4-8 Valve Anti-slosh 53 4 4-9 Purge Line 3 53 4 4-7 Valve Slant Cartrdg NOTE: All component dimensions given in U.S. inches inch = 5.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Briggs & Stratton -800-33-373 Engine Power Rating Information The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J995 (Revision 00-05). Torque values are derived at 3060 RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual on-site or net power). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-toengine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine. 37
STEERING ASSEMBLY 6 5 45 6 3 8 63 64 8 60 9 9 35 59 63 8 7 67 66 9 8 7 57 58 4 6 67 6 6 69 4 5 6 4 5 3 8 68 70 5 3 steering-tex_husqsr_4 53 53 4 64-80 Wheel, Steering 53 9 59-68 Axle Asm., Front 4 53 40 30-87 Spindle Asm., LH 5 53 40 30-88 Spindle Asm., RH 6 53 49-3 Bearing, Race Thrust Harden 7 53 7-48 Washer 5/3 x -5/8 x 6 Ga. 8 8 00 00-9 Ring, Clip #T5304-75 9 53-3 Cap, Spindle 3 53 7-49 Washer 5/3 x -/4 x 6 Ga. 4 80 04 06-00 Washer, Lock Hvy Hlcl Spr 3/8 5 873 54 06-00 Nut, Crown Lock 3/8-4 unf 6 53 40 8-9 Shaft Steering 9 53 9 47-9 Plate Steering 53 8 67-37 Adapter, Wheel Steering 53 4 05-37 Steering, Support Lower 6 53 4 59-87 Insert, Wheel Steering 8 87 00 06- Screw 3/8-6 x 3/4 38 45 89 8 38- Washer 9/6 x -3/8 x Ga. 5 873 94 08-00 Nut Hex Jam Toplock /-0 unf 53 53 8 89-67 Washer Hardened.793 x.637 x.060 57 53 9 7-46 Bracket Upstop 58 53 9 47-47 Bolt Shoulder Sector Pivot CFM 59 53 9 47-48 Washer Thrust Sector Steering 60 873 97 0-00 Nut Flange Lock 5/8-6 53 9 47-40 Draglink, LH 6 53 9 47-4 Draglink, RH 63 87 00 05- Screw 5/6-8 x 3/4 64 53 9 98-49 Retainer Clip Spring Steering 66 87 0 07-48 Bolt Hex Fghd 7/6-4 x 3 Serr 67 53 9 47-37 Bushing PM Front Axle 68 873 90 07-00 Nut Lock Flange 7/6-4 Gr. 5 69 53 9 9-6 Washer.5 x.505 x.8 70 53 9 6-97 Bracket Deck Susp. Front 35 53 9 47-3 Gear, Sector Plate NOTE: All component dimensions given in U.S. inches inch = 5.4 mm
MOWER LIFT 7 87 87 90 98 3 0 88 97 89 9 97 9 87 89 lift-tex_3 89 87 53 4 0-7 Shaft Asm. Cross, Lift 3 53 9 5-3 Lever Asm., Lift 7 53 4 5-55 Grip, Lever 0 53 9 63-4 Spring Torsion 87 53 9 4-09 Pin Cotter 7/6 Bow Tie Lock 88 53 4 07-0 Spring Lift Assist 89 89 9 9- Washer Clear Zinc 90 53 9 4-08 Pin Cotter 5/6 Bow Tie Lock 9 53 9 5-8 Link Lift Susp Mower Rear 97 87 00 06- Screw 3/8-6 x.75 98 53 9 5-64 Link Lift Susp. Front Mower NOTE: All component dimensions given in U.S. inches inch = 5.4 mm 39
MOWER DECK 46 46 47 6 85 39 49 5 46 4 98 3 33 97 43 54 48 50 33 3 7 3 4 4 33 3 30 6 7 7 0 49 3 9 5 6 94 6 9 4 7 90 89 5 87 88 90 4 0 87 3 8 8 48_Deck_tex r 40
MOWER DECK 53 40 35-8 Deck Weldment Mower 6 53 9 7-48 Cover Mandrel LH 7 53 9 9-0 Cover Mandrel RH 8 53 9 30-03 Bolt 7/6 Asm. Blade 53 8 00-54 Blade High Lift - - 53 7 39- Blade Mulching 53 40 48-5 Rod Anti-Sway 3 53 8 7-9 Shaft Asm. w/lower Bearing 4 53 8 7-8 Housing, Mandrel 5 53 04-85 Bearing, Ball, Mandrel 6 89 3 3- Washer 3/3 x 3/6 x Ga. 7 87 05-05 Bolt 5/6-8 x 5/8 8 87 4 05-05 Bolt RdHd 5/6-8 unc x 5/8 9 53 9 4-08 Pin Cotter 5/6 Bow Tie Lock 0 53 7 43-78 Baffle Vortex 873 68 05-00 Nut, Crownlock 5/6-8 unc 53 7 44-93 Stripper Mandrel 4 53 0 53-04 Cap Sleeve 5 53 7 8-0 Spring, Torsion 6 53 04-5 Nut, Push 7 53 8 7-07 Deflector Shield 9 53 3 4-9 Rod, Hinge 30 53 7 39-84 Screw, Thdroll Washer Head 3 53 8 76-90 Washer, Spacer Mower Vented 3 53 5 35-3 Pulley, Mandrel 33 53 40 0-34 Nut, Flg. Top Lock 39 53 9 73-80 Pulley, Idler, 4.50 Hub 43 53 9 60-65 Arm, Idler 46 53 3 77-9 Screw, Thdroll. /4-0 x 5/8 47 53 9 7-4 Belt Deck Drive 48 53 9 73-79 Pulley Idler 4.50 RAW 49 873 90 06-00 Nut, Lock Flg. 3/8-6 unc 50 87 49 06-36 Screw TT 3/8-6 x -/4 5 53 9 3-97 Pulley Idler 48" Primary 54 87 06- Bolt Carr. Sh 3/8-6 x -/ Gr. 5 97 53 7 85-5 Washer Hardened 98 53 9 6-05 Spring Drive 3 87 05-08 Bolt Rdhd Sqnk 5/6-8 x 3/4 4 53 9 74-5 Rod Tension Relief 6 53 9 34-06 Bolt, Shoulder 7 53 7 48-73 Gauge Wheel 0 89 3 0- Washer 3/3 x -/4 x Ga. 53 8 75-57 Bushing Tension Relief 85 873 90 07-00 Nut Lock Flange 7/6-4 Gr. 5 87 53 9 5-6 Stud Fastener w/"d" Anti-Rotation 88 873 90 05-00 Nut Lock Hex Flange 89 53 9 5-85 Arm Susp. Mower Rear 90 53 9 65-39 Bolt Shoulder 94 87 4 07-6 Bolt Carr Sqnk 7/6-4 x 4 53 5 9-7 Screw TT #0-3.5 3/8 Flange 4 53 4 55-98 Port, Washout - - 53 4 64-05 Coupling Quick Connect - - 53 8 7-9 Mandrel Assembly (Includes housing, shaft assembly, and bearing only - pulley/nut/washer and blade bolt/washers not included) - - 53 43 8-5 Replacement Mower, Complete NOTE: All component dimensions given in U.S. inches inch = 5.4 mm 4
SEAT ASSEMBLY 8 4 7 8 8 7 40 8 0 6 37 44 43 37 3 seat-tex_6.5sl_ 53 4 40-68 Seat 53 8 0-66 Bracket Pivot Fender 3 53 4 06-75 Strap, Asm Fender 6 873 80 06-00 Nut, Lock w/ins. 3/8-6 unc 7 53 4-8 Spring, Seat Cprsn 8 53 7 8-77 Bolt 5/6-8 unc x 3/4 w/sems 0 53 9 69-77 Pan, Seat 53 7 8-5 Bolt, Shoulder 5/6-8 37 873 80 05-00 Nut, Lock 5/6-8 unc 40 53 9 76-6 Handle Slide Seat 4 53 9 8-00 Spring Latch Seat 43 874 76 06- Bolt 3/8-6 x 3/4 44 89 3 38- Washer 3/3 x -3/8 x Ga. NOTE: All component dimensions given in U.S. inches inch = 5.4 mm 4
DECALS 6 5 7 6 4 4 4 9 5 6 3 8 53 4 9-38 Decal, Operator's 53 43 63-90 Label 3 53 4 4-0 Decal, Warning Spark Arrestor 4 53 9 5-54 Decal, Fender 5 53 7 84-55 Decal, Caution 6 53 4 95-57 Decal, Eng. HP 8 53 9 87-85 Decal, Mower Sch. 9 53 4 50-05 Decal, Battery Dnge/Poi 4 53 4 00-55 Decal, Panel Side 5 53 4 38-9 Decal, Cust. Resp. 6 53 4 9-96 Decal, Hood Logo 7 53 4 99-97 Decal, Replacement - - 53 6 69-60 Decal, Bypass - - 53 4 08-05 Pad, Footrest, LH - - 53 4 08-06 Pad, Footrest, RH - - 53 43 08-90 Manual, Owner's (English) - - 53 43 08-9 Manual, Owner's (Spanish) WHEELS AND TIRES 3 7 6 4 0 5 9 8 53 05 9-9 Cap, Valve, Tire 53 06 5-39 Stem, Valve 3 53 3 83-36 Rim Assembly, Front 4 53 05 99-04 Tube, Front (Ser vice Item Only) 5 53 0 6- Tire, Front 6 53 49-57 Fitting, Grease (Front Wheel Only) 7 53 49-59 Bearing, Flange (Front Wheel Only) 8 53 7 50-39 Cap, Axle (Front Wheel Only) 9 53 3 84-68 Tire, Rear 0 53 49-6 Tube, Rear (Service Item Only) 53 3 83-37 Rim Assembly, Rear - - 53 4 43-34 Sealant, Tire (0 oz. Tube) wheel_art_-vgt NOTE: All component dimensions given in U.S. inches inch = 5.4 mm 43
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOLD ALONG DOTTED LINE THIS IS A 5 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 5 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 5 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes.. Fold this page along dotted line indicated above.. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill. 44
Consumer Wheeled Products - Limited Warranty Husqvarna warrants to the original retail purchaser that this product is free from defects in material or workmanship under normal use and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. This Limited Warranty may not be transferred to any subsequent purchaser of this product. Certain components (e.g., engines and transmissions) are excluded from coverage, and other limitations apply, as described in this document. Husqvarna will repair or replace at its discretion, any defective product or part covered by the Limited Warranty, free of charge at any authorized Husqvarna Servicing Dealer/Center using original OEM Husqvarna replacement parts, subject to the limitations and exclusions described below. Husqvarna does not offer an over-the-counter exchange program. DISCLAIMERS, LIMITATIONS AND EXCLUSIONS. WARRANTY DISCLAIMER. THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY PROVIDED BY HUSQVARNA AND THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF, EXCEPT AS MAY BE PROVIDED BY LAW. THIS WARRANTY IS GIVEN ONLY BY HUSQVARNA, AND MAY BE MODIFIED ONLY BY HUSQVARNA. THIS LIMITED WARRANTY IS THE FINAL EXPRESSION OF OUR AGREEMENT, AND IS A COMPLETE AND EXCLUSIVE STATEMENT OF THE TERMS OF THAT AGREEMENT. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY BASED ON LOCALITY. LIMITED DURATION. ANY WARRANTY THAT MAY BE IMPLIED BY LAW (INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE AND IMPLIED WARRANTY OF MERCHANTABILITY) IS LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD UNDER THIS LIMITED WARRANTY. SOME LOCALITIES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. 3. EXCLUSIVE REMEDIES. SOME LOCALITIES, INCLUDING THE PROVINCE OF QUEBEC, DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR INJURY TO PERSON OR FOR DAMAGES RESULTING FROM THE FAULT OF THE MANUFACTURER AND/OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. AS SUCH, SOME OF THE FOLLOWING LIMITATIONS MAY NOT APPLY TO YOU. THE ABOVE REMEDIES ARE THE EXCLUSIVE REMEDIES FOR ANY BREACH OF THIS LIMITED WARRANTY. NO OTHER REMEDY, INCLUDING, BUT NOT LIMITED TO ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES, FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR PROPERTY, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS SHALL BE AVAILABLE, AND ALL SUCH DAMAGES ARE HEREBY DISCLAIMED. 4. Engines, Transmissions and certain other components are NOT covered. This Limited Warranty does not cover any of the following: (a) Engines and Attachments.Except where otherwise indicated on Exhibit A, all Engines and Attachments are not covered by this Limited Warranty. In most cases, these items are NOT manufactured by Husqvarna in which case they may be covered separately by their respective manufacturer's warranties if one is provided and included with the product at the time of purchase. All such claims must be submitted and sent to the appropriate manufacturer or as otherwise directed in those separate warranties. Husqvarna is not authorized to handle warranty adjustments or repairs on engines manufactured by Briggs & Stratton, Honda, Kawasaki, or Kohler (with the exception of models equipped with LCT engines). Husqvarna does not assume any warranty obligation of the other manufacturers' engines under this Limited Warranty. (b) Transmissions. Except where otherwise indicated on ExhibitA, Transmission / Transaxle (including Drive Systems) are not covered by this Limited Warranty. In most cases, these items are NOT manufactured by Husqvarna in which case they may be covered separately by their respective manufacturer's warranties if one is provided and included with the product at the time of purchase. The following transmission / transaxle manufacturers, Dana, Hydro-Gear, Tuff-Torq provide a warranty for the transmission / transaxle to the ultimate purchaser or to Husqvarna. Husqvarna will assign the transmission / transaxle manufacturer's warranty or any rights thereof to the original purchaser of the unit. To obtain transmission / transaxle warranty service, first contact the retailer who you purchased the unit from. Should you require assistance or have any questions concerning transmission / transaxle warranty coverage, contact Husqvarna directly at our website www.husqvarna.com or call 800-487-595 (US) or 800-805-553 (Canada) for an authorized Husqvarna service provider. All such claims must be submitted and sent to the appropriate manufacturer or as otherwise directed in those separate warranties. Husqvarna is not authorized to handle warranty adjustments or repairs on transmissions or transaxles. Husqvarna does not assume any obligations under this Limited Warranty for the above listed manufacturers (for exceptions - see Exhibit A). (c) Expendable Parts. This Limited Warranty does not cover general maintenance parts and items ("Expendable Parts"), including without limitation spark plugs, bulbs, filters, lubricants, starter cords, belts, blades, and blade adapters. (d) Emissions Control Components. This Limited Warranty does not cover Emissions control equipment and components to the extent regulated by the U.S. Environmental Protection Agency or similar state, provincial or federal agencies. Such equipment and components are covered by a separate emission control warranty statement supplied with your new product. Please consult this separate warranty statement for details. 5. Any COMMERCIAL, INSTITUTIONAL, AGRICULTURAL, INDUSTRIAL, INCOME PRODUCING, or RENTAL use will result in either No Warranty or a Shortened Warranty Period. Depending on the product, there is either NO WARRANTY (whether statutory, contractual or otherwise) or a reduced warranty if the product is used for commercial, institutional, agricultural, industrial, income producing, or rental purposes and, in such circumstances, this Limited Warranty is offered instead of and replaces any warranty regime provided for by law. Please refer to Exhibit A. 6. Reconditioned or Refurbished Products have a 30 Day Limited Warranty. Under this Limited Warranty, Certified Factory Reconditioned or Refurbished products have a 30 Day Limited Warranty for parts and labor for Non-Commercial Use. Products are only reconditioned at the Husqvarna Factory. 7. Owner's (Your) Responsibilities. To preserve your rights under this Limited Warranty, you must exercise reasonable care and use of the product, including, following the preventative maintenance, storage, fuel and oil usages as prescribed in the enclosed operator's manual. For example, the following items are the Owner's responsibility and are not covered by this Limited Warranty: a. Set-up and pre-delivery service, and engine tune-ups; b. Adjustments after the first (30) thirty days of purchase and beyond, such as throttle cable, belt guides adjustments; and c. Preventative maintenance as outlined in the operator's manual. In addition, you must cease using the product immediately upon any failure or damage. The product should be taken to an authorized Husqvarna servicing dealer prior to any further use. 8. Damages resulting from normal aging, wear and tear or neglect are NOT covered. The Limited Warranty does not cover damage other than that resulting from defects in material or workmanship. The following are NOT considered defects in material or workmanship, and therefore are NOT covered. 45
(a) (b) (c) Abrasion to mower decks; Tires damaged by external punctures; Natural discoloration of materials due to ultraviolet light; (d) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures; In addition, this Limited Warranty does not cover damages, malfunctions or failures resulting from abuse or neglect of the product related to or including any of the following: (e) (f) (g) (h) (i) (j) (k) (l) (m) (n) (o) (p) (q) Failure to provide or perform required maintenance services as prescribed in the operator's manual; Abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, use of unauthorized attachments, Lack of lubrication or engine failure, due to the use of oils that do not meet Engine manufacturer's specifications; Use of gasohol, containing methanol (wood alcohol). Gasohol which contains a maximum 0% ethanol (grain alcohol) or 5% MTBE (methyl/tertiary/butyl/ether) is approved; Use of ether or any starting fluids; Pressure cleaning or steam cleaning the product; Use of spark plugs other than those meeting emission performance requirements listed in the operator's manual; Tampering with engine speed governor or emission components, or running engines above specified and recommended engine speeds as listed in your operator's manual; Operation of the unit with improperly installed/removed or modified cutting shields, guards, or safety devices; Any removed/damaged air filter, excessive dirt, abrasives, salt water, moisture, corrosion, rust, varnish, stale fuel, or any adverse reaction due to incorrect storage procedures; Failures due to improper set up, pre-delivery service or repair service by anyone other than an authorized Husqvarna servicing dealer during the warranty period; Dirt contaminated grease or oil, use of incorrect type of greases or oils, failure to comply with recommended greasing intervals, water or moisture damage, and/or improper storage; Sprayers pumping or spraying caustic or flammable materials, lack of or broken strainers; or Continued use of product, after initial operational problem or failure occurs. 9. Reinforced Stamped (Armor Protected) 0 Year Limited & Fabricated Limited Lifetime, Deck Warranties. These Limited Warranties are for the deck shell only mechanical components/parts such as belts, pulleys, spindle housings, bearings, blades, rods, height adjusters, caster/anti scalp wheels are NOT covered. The Limited Lifetime Warranty does not cover damage other than that resulting from defects in material or workmanship. The following are NOT considered defects in material or workmanship, and therefore are NOT covered: (a) Abrasion to mower decks, including sand wear; (b) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures; (c) Rust and corrosion; and (d) Natural discoloration of paint or other materials due to ultraviolet light. HOW TO OBTAIN SERVICE 0. Authorized Husqvarna Servicing Dealer/Center. In order to obtain warranty coverage it is your responsibility (at your expense) to deliver or ship your Husqvarna unit to an authorized Husqvarna Servicing Dealer/Center and arrange for pick-up or return of your unit after the repairs have been made. If you do not know the location of your nearest authorized Husqvarna Servicing Dealer, call Husqvarna, at -800-487-595 during the hours of 8:00 AM to 8:00 PM Eastern Standard Time, or visit www.husqvarna.com. Should you require assistance or have questions concerning this Limited Warranty, you may contact us at 800-487-595 (US) or 800-805-553 (Canada) during the hours of 8:00 AM to 8:00 PM Eastern Standard Time or contact us through the web at www.husqvarna.com.. Documentation Required. You must maintain and present Proof of purchase (including date, product model and, if applicable, engine serial number) to an authorized Husqvarna Servicing Dealer for warranty service under this Limited Warranty. Proof of purchase rests solely with you. Husqvarna encourages you to register your product online at www.usa.husqvarna.com (US & Canada) to help ensure, among other things, that you can be notified of important product information. However, registering your product is not a condition of warranty service. Husqvarna Professional Products, NA, Inc. 9335 Harris Corners Parkway, Suite 500, Charlotte, NC869 575 49 43-0 W 0 IR 46
Consumer Wheeled Limited Warranty Chart 0 Consumer (personal, household use only) Commercial (any commercial, professional, institutional, agricultural, or income producing use, other than Rental Use) Exhibit A Rental (any rental usage) Product/Component Riding Lawn Tractors: Frame, Chassis, Front Axle 5 Years No Warranty No Warranty Engine* * * * Transmission (if made by Husqvarna/Peerless) 3 Years No Warranty No Warranty Transmission (if third party)** ** ** ** XLS Models only - stamped deck shell. Armor Protected Limited Warranty 0 Years No Warranty No Warranty Fabricated Deck shell. Limited Lifetime Warranty *** No Warranty No Warranty Battery Year Pro-rated No Warranty No Warranty Other Non-Expendable Components 3 Years No Warranty No Warranty Residential Zero Turn Mowers ( RZ Only ) Engine* * * * Transmission ** ** No Warranty No Warranty RZ463 (96700980 & 96700980) RZ546 (96700360 & 96700360) - stamped deck shell. Armor Protected Limited Warranty 0 Years No Warranty No Warranty Fabricated Deck shell. Limited Lifetime Warranty *** No Warranty No Warranty Battery Year Pro-rated No Warranty No Warranty Other Non-Expendable Components 3 Years No Warranty No Warranty Residential Zero Turn Mowers ( MZ & EZ ) Engine* * * * Transmission ** ** ** ** MZ544S & MZ545S (96700390 & 50) - stamped deck shell. Armor Protected Limited Warranty 0 Years No Warranty No Warranty Fabricated Deck shell. Limited Lifetime Warranty *** No Warranty No Warranty Battery Year Pro-rated No Warranty No Warranty Other Non-Expendable Components 3 Years Year No Warranty LE475 Edger, Tillers, Snow Throwers Engine* * * * Other Non-Expendable Components Years 90 days 90 days Tiller Tines *** No Warranty No Warranty Walk Behind Mowers, High Wheel Trimmer Engine* * * * Battery Year Pro-rated No Warranty No Warranty Other Non-Expendable Components 3 Years No Warranty No Warranty Hovering Trimmers Engine* * * * Other Non-Expendable Components Years Year 90 days Front Mounted Deck Riders Engine* * * * Transmission Years No Warranty No Warranty Other Non-Expendable Components Years No Warranty No Warranty Cultivators Battery Year Pro-rated No Warranty No Warranty Other Non-Expendable Components Years No Warranty No Warranty Pressure Washers Model 555PW: Engine* * * * Pump Years No Warranty No Warranty Other Non-Expendable Components Years No Warranty No Warranty All other Pressure Washers (607PW, 903PW, 340PW) Engine* * * * Pump Years Years No Warranty Other Non-Expendable Components Years Years No Warranty Generators Engine* * * * Other Non-Expendable Components* * Years (nd Year Parts Only) * Years-365GN (nd Year Parts Only) No Warranty Spreaders 47
Consumer Wheeled Limited Warranty Chart 0 Consumer (personal, Commercial (any commercial, household use only) professional, institutional, agricultural, or income producing use, other than Product/Component Rental Use) Exhibit A Rental (any rental usage) Spreader Year Year Year Robotic Mowers Robotic Mower Years 90 days 90 days Battery Year Year Year Parts & Accessories (if purchased) Accessories (e.g., grass catcher, bumper guard accessories, etc. Year No Warranty No Warranty Parts (e.g., belts, blades, etc.) 30 days No Warranty No Warranty Parts & Accessories (if replaced in Warranty Service) Replacement parts and/or accessories provided under this Limited Warranty are warranted only for the BALANCE of the warranty period applicable to the part or accessory that was replaced. See to left See to left See to left Consumer Commercial Rental * See Separate Engine Manufacturer's or Manufacturer's warranty. LCT Engines on specific Snow Throwers & Tillers, warranty through Husqvarna. ** See reference (b) of the warranty statement. RZ - Two () Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network. EZ - One () Year Commercial warranty, parts & labor, with Husqvarna. Two () Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network. MZ - Two () Year Commercial warranty, parts & labor, with Hydro-Gear Distributor network. *** "Limited Lifetime Warranty" on Tiller tines and Fabricated Deck shell is for the life of the product or 7 (seven) years after the last date of the complete unit's final production, whichever comes first. Deck Shell replacement will be limited to a maximum of two () decks within the Limited Lifetime Warranty. Armor Protected Stamped Deck Shell Example Below Fabricated Deck Shell Example Below Armor Protected Stamped Deck Shell Reinforced area Stamped Deck Shell below, NOT reinforced No reinforced area 0.. BD Printed in the U.S.A.