W here the re is MiBoxer t her e is power C4 Smart Charger Users Manual
( English ) C4 User Manual Features Compatible lithium battery (4.2V, 4.35V), lithium iron phosphate (3.6V), nickel hydrogen / nickel chromium (1.48V) four specifications battery charge Suitable for different types of cylindrical rechargeable lithium battery Up to 800mA / channel fast charge The charging current and discharge current can be set manually High precision reference voltage source calibration Stop charging automatically when the battery is fully charged With battery anti-reverse and anti-short protection Automatically detects the battery and displays the charge status Automatically measure battery resistance and charge to measure battery capacity Supports discharge measurement Battery capacity (fourth channel only) Supports 4 channels while charging independently, without affecting each other Supports small capacity battery charging Support lithium battery repair function Supports DC12V car charger Made of PC fire retardant material Excellent thermal design Excellent circuit design, 12 months long warranty Parameters Input voltage: AC90~260V 50/60Hz 0.4A(Max) 18W DC12V 2A Output Voltage: 4.35V±% / 4.2V±1% / 3.6V±1% /1.48V±1% Output Current: (100~800mA)*4 Size: 158mm*103mm*38mm (L*W*H) Weight: 285g (No battery & cable included) Compatible with: Li-ion / IMR / INR / ICR / LiFePO4: 10340, 10350, 10440, 10500, 12340, 12500, 12650, 13450, 13500, 13650, 14350, 14430, 14500, 14650, 16500, 16340 (RCR123), 16650, 17350, 17500, 17650, 17670, 18350, 18490, 18500,18650, 22500, 22650,25500, 26500, 26650 Ni-MH/Ni-Cd: AA, AAA, AAAA, C LCD Display Introduction Large size LCD display states the voltage, current, charging time, mode, battery type, internal resistance, battery capacity data, let you understand the battery charging status easily. The LCD back-light will become dark after 2 minutes if there is no operation.
1st slot 2nd slot 3rd slot 4th slot Charging Capacity Discharging Charging Measure Charging Time Battery Capacity Battery Type Charging Mode Charging Current Battery Voltage Charging Current / Discharging Current / Battery Resistance Battery Detection And Error Report Battery Inspection Batteries inserted with polar reversed Short circuit Error Report The corresponding slot battery marking blink to notify the user of short circuit an Battery will come into charging status if install with correct method User's Guide 1. Connect the power supply 2. Put the battery Into any channel, the charger automatically identify the battery type, and began to detect battery-related data, displayed on the LCD screen, 3. After the battery resistance measurement is completed, The optimal charging current (maximum 800mA, minimum 100mA) will be automatically selected according to the battery characteristics after 6 seconds. 4. Short press to switch the C1-C4 channel information display. The LCD backlight will also be turned on. Press and hold to turn off the LCD backlight. NOTE LiFePO4 / 4.35V Li-ion battery, the charger can not be identified automatically, you need to manually select the battery type. If the LiFePO4 is not set manually, the charger will charged the battery as Li-ion 4.2V and the battery will be at risk of explosion. Battery type setting Put the battery into any channel, short press key, until the BAT flashing, hold the button, Loop switch to choose the battery type, 10 seconds latter automatic exit.
Charging current setting 1. 1.Place the battery in any slot. 2. Press and hold the key until the LCD screen flashes, 3. Press the key repeatedly to toggle the charge current. Select the range of 100mA to 800mA. 4. Press and hold the key to determine the current. Note: When flashing, it indicates that the charger automatically selects the charging current according to the battery internal resistance. Battery resistance measurement Put the battery in any channel, the charger will display the battery voltage, and automatically measure the battery resistance. LCD screen display, charger testing the battery resistance, detection time about 8 seconds. LCD screen display charger measured battery resistance is 68mΩ. Note: The internal resistance display time is about 6 seconds, the battery resistance measurement is completed, automatically enter the charging mode. Measurement Battery capacity by discharge(only 4TH slot) Put the battery in the 4th slot, short press until flashes, and then press the key to switch the battery capacity function to turn on and off. When displayed, indicates that the test battery capacity function is on. When displayed, indicates that the test battery capacity function is off. Note: When the measurement battery function is turned on, the charger will first charge the battery, and then discharged via constant current, real-time calculation of battery capacity and save the capacity data, after discharge the charger will fully charge the batteries again and stop charging. Discharge current setting (only 4TH slot ) 1. Place the battery in the fourth channel of the charger and the battery is in the discharge mode, 2. Press and hold the button until the LCD screen flashes, 3. Short press key to select the discharge current, select the range of 100mA-400mA. 4. Press and hold the key to determine the current. Note: Flash, the charger according to the battery internal resistance automatically select the discharge current.
Measurement Battery capacity by Charging Put the battery into any channel of the charger, the charger will automatically calculate the capacity of the battery charge. Flashes, the capacity value is the actual charge or discharge capacity of the battery. battery always show, the value is the total capacity of the Precautions 1. The charger is restricted to charging Li-ion, IMR, ICR LiFePO4, Ni-MH/Ni-Cd rechargeable batteries only. Never use the charger with other types of batteries as this could result in battery explosion, cracking or leaking, causing property damage and/or personal injury. 3. The safe operation temperature for the charger is between -10~40 C, and the safe storage temperature is -20-60 C.Do not expose the device to direct sunlight, heating devices, open flames; avoid extreme high or extreme low ambient temperatures and sudden temperature changes. 4. The charger is for use of adults above 18 years old. Children under this age must be supervised by an adult when using the charger. 5. Never charge or discharge any battery having evidence of leakage, expansion/swelling, damaged outer wrapper or case,color-change or distortion. 6. Never attempt to charge primary cells such as Alkaline, Zinc-Carbon, Lithium, CR123A, CR2, or any other unsupported chemistry due to risk of explosion and fire 7. Do not charge a damaged IMR battery as doing so may lead to charger short-circuit or even explosion. Warranty Warranty is provided only for products purchased from an authorized source.this applies to all products. Any DOA / defective product can be exchanged for a replacement through a local distributor/dealer within the 15 days of purchase. After 15 days, all defective / malfunctioning products can be repaired free of charge for a period of 12 months (1 year) from the date of purchase. Beyond 12 months (1 year), a limited warranty applies, covering the cost of labor and maintenance, but not the cost of accessories or replacement parts. Free warranty does not apply to the following conditions: 1. Broken down, Reconstructed and/or Modified by unauthorized parties 2. Damaged from wrong operations (i.e. Reserve polarity installation, Installation of non-rechargeable batteries, or Violation warning operation) 3. Damaged by batteries leakage. For the latest information on products and services, please contact a local distributor or send an email to sales@miboxer.com
Packing list Name Quantity C4Charger 1 PC User Manual 1 PC Power Cable 1 PC MiBoxer Hi-Tech Co.,Ltd. Add: Floor 2, Buiding D, Fusen Technology Park, Hangcheng Road, Bao an District, Shenzhen City, Guangdong Province, China E-mail: sales@miboxer.com http://www.miboxer.com Made in China Scan for more