Section 12 Contain-It Secondary Containment Piping System Serviced by GF Little Rock
Table of Contents Contain-It Pipe 12.4 Fittings 12.5 Terminations 12.7 Centralizers 12.8 Accessories 12.9 Adhesive Requirements 12.10
Glossary S = Contain-It Socket SPG = Spigot End (same dimension as pipe outside diameter) MPT = Male Pipe Thread FPT = Female Pipe Thread Product Line Description Discount 39 Fittings 41 Pipe 42 Accessories The technical information given in this publication implies no warranty of any kind and is subject to change without notice. Please consult our Terms and Conditions of Sale. Not for Use with Compressed Air or Gases DO NOT TEST with Air or Air over Water GF Piping DOES NOT RECOMMEND the use of thermoplastic piping products for systems to transport or store compressed air or gases, or the testing of thermoplastic piping systems with compressed air or gases in above or below ground locations. The use of GF Piping products in compressed air or gas systems automatically voids the warranty for such products, and their use against our recommendation is entirely the responsibility and liability of the installer. GF Piping will not accept responsibility for damage or impairment from its products, or other consequential or incidental damages caused by misapplication, incorrect assembly, and/or exposure to harmful substances or conditions. The only exception to this recommendation is when testing the Contain-It Secondary System or the Fuseal Squared Double Containment Piping System s containment joints.
Contain-It Pipe Secondary Containment Piping System Material: Clear PVC P/L: 41 Pipe Split Pipe - 10 foot lengths Plain Ends Inch Size Part Number List $/ft. Lift Qty (ft.) Minimum Order Qty (ft.) 4 *8326-040AA 12.00 360 60 6 *8326-060AA 25.50 120 20 Solid Pipe - 20 foot lengths Plain Ends Inch Size Part Number List $/ft. Lift Qty (ft.) Minimum Order Qty (ft) 4 *8326-040AB 6.75 520 80 6 *8326-060AB 15.00 340 60 ^ = 40% Restock Charge * = Non-Cancelable / Non-Returnable 12.4
Contain-It Fittings Secondary Containment Piping System Material: Clear PVC P/L: 39 Fittings Standard Pack Quantities; No Broken Packs Containment Coupling Standard, Split (SxS) 4 4629-040 50.00 5 6 4629-060 75.00 5 Containment Coupling Extended, Split (SxS) 4 4629-040E 55.00 5 6 4629-060E 80.00 5 Maximum Gap: 5.50 Containment Coupling Reducing, Split (SxS) 6x4 4629-532 100.00 5 Containment 90 Ell, Split (SxS) 4 4606-040 65.00 5 6 4606-060 100.00 5 Containment 45 Ell, Split (SxS) 4 4617-040 65.00 5 6 4617-060 100.00 5 Containment Tee, Split (SxS) 4 4601-040 75.00 5 6 4601-060 110.00 5 Containment Piping ^ = 40% Restock Charge * = Non-Cancelable / Non-Returnable 12.5
Containment 45 Wye, Split (S x S x S) 4 4683-040 100.00 5 6 4683-060 145.00 5 Containment Cap, One Piece (S) 4 4647-040 40.00 5 6 4647-060 60.00 5 Containment Female Adapter, One Piece (S x FPT) 4 4635-040 50.00 5 6 4635-060 75.00 5 Plug, One Piece (MPT) 4 4650-040 40.00 5 6 4650-060 60.00 5 Adapter Sleeve, One Piece (IPS Spg x S) 4x4 4687-040 40.00 10 6x6 4687-060 60.00 10 Containment PPFR Floor Drain, One Piece (IPS Spg x MPT) 3x6 ^46104-530 520.00 1 4x6 ^46104-532 520.00 1 For use with Fuseal Piping only ^ = 40% Restock Charge * = Non-Cancelable / Non-Returnable 12.6
Contain-It Terminations Secondary Containment Piping System Material: Clear PVC or Alcryn P/L: 39 Fittings Standard Pack Quantities; No Broken Packs Termination Fitting Rigid PVC, Split (Contain-It to IPS) 4x½ *4628-415 85.00 1 4x¾ *4628-416 85.00 1 4x1 *4628-417 85.00 1 4x1¼ *4628-418 85.00 1 4x1½ 4628-419 85.00 1 4x2 4628-420 85.00 1 6x2½ *4628-529 120.00 1 6x3 4628-530 120.00 1 6x4 4628-532 120.00 1 Test Termination Fitting Rigid PVC, Split (Contain-It to IPS) (with two 3/8 NPT Plugs) 4x2 4628-420T 80.00 1 6x4 4628-532T 120.00 1 Termination Fitting Flexible Alcryn, One Piece (Contain-It to IPS/Metric) 4x½ or 20mm 4628-415A 50.00 1 4x¾ or 25mm 4628-416A 50.00 1 4x1 or 32mm 4628-417A 50.00 1 4x1¼ or 40mm 4628-418A 50.00 1 4x1½ or 50mm 4628-419A 50.00 1 4x2 or 63mm 4628-420A 50.00 1 6x2½ or 75mm 4628-529A 150.00 1 6x3 or 90mm 4628-530A 150.00 1 6x4 or 110mm 4628-532A 150.00 1 Alcryn is a registered trademark of Ferro Corporation. Test Termination Fitting Flexible Alcryn, One Piece (Contain-It to IPS/Metric) 4x½ or 20mm 4628-415AT 50.00 1 4x¾ or 25mm 4628-416AT 50.00 1 4x1 or 32mm 4628-417AT 50.00 1 4x1¼ or 40mm 4628-418AT 50.00 1 4x1½ or 50mm 4628-419AT 50.00 1 4x2 or 63mm 4628-420AT 50.00 1 6x2½ or 75mm 4628-529AT 150.00 1 6x3 or 90mm 4628-530AT 150.00 1 6x4 or 110mm 4628-532AT 150.00 1 Containment Piping 12.7
Contain-It Centralizers Secondary Containment Piping System Material: PVC P/L: 39 Fittings Standard Pack Quantities; No Broken Packs Custom Centralizers are available upon request Centralizer (Contain-It x IPS) 4x½ *4686-415 25.00 25 4x¾ *4686-416 25.00 25 4x1 *4686-417 10.00 25 4x1¼ *4686-418 25.00 25 4x1½ 4686-419 10.00 25 4x2 4686-420 10.00 25 6x2½ *4686-529 35.00 10 6x3 4686-530 15.00 25 6x4 4686-532 15.00 25 6x½ Twin *4686-811 85.00 5 6x¾ Twin *4686-813 85.00 5 6x1 Twin *4686-815 85.00 5 Centralizer (Contain-It x Copper) Inch Size Part Number List /ea. Std. Pack 4x½ *4686-415C 25.00 10 4x¾ *4686-416C 25.00 10 4x1 *4686-417C 25.00 10 4x1¼ *4686-418C 25.00 10 4x1½ *4686-419C 25.00 10 4x2 *4686-420C 25.00 10 6x2½ *4686-529C 35.00 10 6x3 *4686-530C 35.00 10 6x4 *4686-532C 35.00 10 Centralizer (Contain-It x Metric) Inch Size Part Number List /ea. Std. Pack 4x20mm 4686-712 25.00 25 4x25mm 4686-713 25.00 25 4x32mm *4686-714 25.00 10 4x40mm 4686-715 25.00 25 4x50mm 4686-716 25.00 25 4x63mm *4686-717 25.00 10 6x75mm 4686-719 35.00 25 6x90mm *4686-720 35.00 10 6x110mm *4686-721 35.00 10 6x20mm Twin *4686-812 85.00 5 6x25mm Twin *4686-814 85.00 5 6x32mm Twin *4686-816 85.00 5 12.8
Contain-It Accessories Secondary Containment Piping System P/L: 42 Accessories Standard Pack Quantities; No Broken Packs Fitting Clip (all fittings include the required number of clips for assembly) 4 & 6 *4693-101 0.30 25 Pipe Clamp 4 & 6 *4693-102 310.00 1 Drill Bits 4 *4693-104 37.00 1 6 *4693-105K 85.00 1 (6 kit contains one bit for injection holes and one bit for crossover holes) Manual Injection Gun - System II Part Number List $/ea. Std. Pack *4694-200 350.00 1 Pneumatic Injection Gun - System II (includes regulator and gauge assembly) Part Number List $/ea. Std. Pack *4694-201 960.00 1 Adhesive Cartridge - System II (limited self life of 18 months) Part Number List $/ea. Std. Pack *4694-302 45.00 12 Containment Piping ^ = 40% Restock Charge * = Non-Cancelable / Non-Returnable Mixing Tip - System II Part Number List $/ea. Std. Pack Straight *4694-303 4.25 10 Flexible *4694-306 20.50 10 Bent *4694-307 11.00 10 12.9
Adhesive Requirements Contain-It Cartridge Fittings/Pipe # of Sockets/Tube 1 cartridge 4 fittings 14 1 cartridge 6 fittings 10 1 cartridge 4 pipe 20 ft. length, both sides 1 cartridge 6 pipe 10 ft. length, both sides Adhesive Cartridge Requirements Calculation This table is designed to assist in the accurate determination of the number of adhesive cartridges required for a specific project. Fittings Quantity of 4 Tees and Wyes Quantity of 4 Fittings (other than tees and wyes) x 3 = x 2 = /14 = Quantity of 6 Tees and Wyes x 3 = Quantity of 6 Fittings (other than tees and wyes) x 2 = /10 = (+) Split Pipe Feet 4 Split Pipe/20 (1 cartridge will fill 20 ft., both sides) = (+) Feet 6 Split Pipe/10 (1 cartridge will fill 10 ft., both sides) = (+) TOTAL CARTRIDGES 12.10