LABORATORY EQUIPMENT FOR CENTRAL MATERIALS LABORATORY AND UPCOUNTRY LABORATORIES FOR FY 208/209 ITEM..0 Testing Sieves Diameter 200mm Stainless Frame and Mesh All to British Standard. Sieve 63μm 0.2 Sieve 7μm 0.3 Sieve 0μm 0.4 Sieve 80μm 0. Sieve 22μm 0.6 Sieve 300μm 0.7 Sieve 42μm 0.8 Sieve 600μm 0.9 Sieve 80μm 0.0 Sieve.8mm 0. Sieve.70mm 0.2 Sieve 2.00mm 0.3 Sieve 2.36mm 0.4 Sieve 2.80mm 0. Sieve.00mm.6 Sieve 6.30mm
..7 Sieve 0mm.8 Sieve 4mm.9 Sieve 20mm.20 Sieve 28mm.2 Sieve 37.mm.22 Sieve 0mm 2.0 200mm Diameter Receiver: Stainless Steel Frame To British Standard 2. 200 mm Diameter Lid: Stainless Steel Frame To British Standard 3.0 Testing sieves Diameter 40mm Stainless steel frame and mesh All to British standard 3. Sieve 600μm 3 3.2 Sieve 300μm 3 4.0 40mm Diameter Receiver: Stainless steel frame To British Standard 4. 40mm Diameter Lid: Stainless steel frame To British standard.0 Dynamic Cone Penetrometer (DCP): TRL Model, can allow measurements up to 2m depth. Spare cones for DCP (60 0 ): TRL Model 3 3 0..
. 6.0 Sand Pouring Cylinder Diameter 00mm complying with BS377/924 6. Calibration can Diameter 00mm complying with BS377/924 6.2 Metal Tray Diameter Hole 00mm complying with BS377/924 6.3 Density Spoon complying with BS 377/924 6.4 Rubber Mallet 0mm diameter complying with BS377/924 6. 2Kg Club Hammer complying with BS 377/924 6.6 Density Chisel complying with BS377/924 6.7 Metal Dibber Tool complying with BS377/924 6.8 Scrapper complying with BS377/924 6.9 Density Hand Pick complying with BS377/924 6.0 Steel Pointed Rods complying with BS377/924 7.0 Sand Pouring Cylinder Diameter 0mm complying with BS377/924 7. Calibration can Diameter 0mm complying with BS 377/924 7.2 Metal Tray Diameter Hole 0mm complying with BS377/924 8.0 Linear Shrinkage Moulds complying with BS 377 Specimen size: 40 x 2.mm Dimension: 60 x 32 x 20mm Material: Brass 2
9.0 Spatulas complying with BS 377 00mm stainless blade with wooden handle 9. Spatulas complying with BS 377 200mm stainless blade with wooden handle 0.0 Porcelain Mortar and Pestle complying with BS 377 & BS 924 80mm Diameter Height : 92mm.0 Compaction Rammers BS 377/924 specification Rammer: 0mm diameter & 4.kg weight Drop : 40mm Finish: Corrosion resistant. Compaction Rammers BS 377/924 specifications Rammer : 0mm diameter & 2.kg. weight Drop: 300mm Finish: Corrosion resistant.2 Compaction moulds Volume 000cm 3 Complying with BS 377 & BS 924.3 Compaction moulds Volume 224cm 3 Complying with AASHTO T80 & ASTM D8 2.0 CBR Moulds complying with BS 377 & 924 Dimensions: 2 x 27mm Construction: All steel, plated A complete mould with collar and perforated base plate. 2. Expansion (Swell) test equipment set comprising of: Perforated swell plate with adjustable stem and steel plated. Swell tripod for mounting swell dial gauge in position on CBR mould and made from a non-corrodable alloy. 2 2 6 0 0 2 20
2.2 Annular Surchage Weights (BS377) Steel Plated, 2kg 2.3 Split Surcharge Weights (BS377) Steel Plated, 2kg 2.4 CBR Cutting Collar (BS 377) Fitting BS CBR mould body and made from plated steel 2. C Spanner (BS 377) Fitting BS CBR moulds and Collars; Steel Quality Supplied in pairs 2.6 CBR Base Plate Tool (BS 377) Fitting CBR mould base plate to assist removal from mould body; steel quality 2.7 CBR Static Compaction Plug (BS 377) 0mm diameter x 0mm high Steel material Complete with removable handle 2.8 Straight Edge (BS 377) Steel Quality Dimensions: 3 x 30 x 300mm 2.9 Square Glass plate (BS 377 & ASTM D438) For Liquid & Plastic Limit determination Dimensions: 00 x 00 x 0mm Plate with ground finish on one side and seamed edges. 0 0 SHS
2.0 Clamped Boss Load Rings: Repeatability within 0.2% of indicated load Accuracy within ± % of indicated load Both repeatability & Accuracy to comply with NIS 04 Accreditation for the Calibration of Force Measuring Rings and Load cells used in Soil Testing. Calibrated in kn and supplied with calibration chart. Supplied complete with detachable Nipple and in a protective foam moulding. 2. Clamped Boss Load Ring capacity kn 2 2.2 Clamped Boss load Ring capacity 0kN 2 2.3 Clamped Boss load Ring capacity 28kN 6 2.4 Clamped Ross load Ring capacity 0kN 2. SHS 3.0 Riffle Boxes (BS 377 & BS 924) with 2 collecting Pans Maximum Particle size: 4.mm Slot width: 7mm Number of Slots: 2 Approximate Capacity: 0.3 litres 3. Riffle Boxes (BS 377 & BS 924) with 2 collecting Pans Maximum Particle size: 0.0mm Slot width: mm Number of Slots: 2 Approximate Capacity: 2.0 litres 3.2 Riffle Boxes (BS 377 & BS 924) with 2 collecting Pans Maximum Particle size: 2.0mm Slot width: 38mm Number of Slots: 8 Approximate Capacity: litres
3.3 Riffle Boxes (BS 377 & BS 924) with 2 collecting Pans Maximum Particle size: 42.mm Slot width: 64mm Number of Slots: 8 Approximate Capacity: 8.0 litres 3.4 Large Capacity Sample Splitter (BS 377 & BS 924) Material Pans: 2 to be included (64 x 229 x 6mm) Capacity: 0.028m 3 Frame: Heavy gauge welded steel Hopper: Lever actuated, clam shell design Chute Bars: 48 aluminium bars, 3mm width Chute Area: 60 mm overall width Chute openings: Adjustable; 0.,.,,2,3,4 or 6 inches Overall Dimensions: 737 x 483 x 999mm 4.0 Moulds for Unconfined Compressive strength of soils (BS 377 & BS 924) A complete set consisting of a mould, set of 2 end plugs, a set of 2 plug displacing collars, plunger & specimen collector Mould size: 200 x 00mm.0 Semi-automatic cone penetrometer (for liquid limit measurements) Standard:BS377 Base: Cast aluminium with adjustable levelling feet Dial Indicator:0mm diameter graduated in 400 x 0.0mm subdivisions Brass made slider with free fall, stop and release push button, automatic zero set; Stainless steel penetration test cone 3mm long, 30 0 angle, weight 00g; Two sample brass cups dia mm x 40mm depth 220 240 V, ph 2
The desired equipment to incorporate a digital automatic controller which releases the plunger head and ensures free falling of the penetration device during the seconds test.. Spare Penetration Test Cones (BS 377) Stainless Steel 3.mm long with smooth polished surface and at an angle of 30 0 6.0 Automatic Vicat Apparatus For setting time test on cement/mortar/gypsum supplied complete with cleaning device and EN 96-3 accessories (Initial setting time needle.3mm diameter, final setting time needle, Glass base plate, mould and PC software. Equipment supplied ready for use. Technical Specifications: Conforms to EN 96-3 Large size 4,3 touch screen color display LAN port for direct connection to PC (include cable) USB Port for data storage on Pen drive (included) Supplied complete with PC Software for data processing, and an integrated printer for results display and setting time plot. Automatic calculation of setting times at programmable penetration depth limits. Penetration measurement by encoder Power: 0w, 230v, ph
Firm ware Specifications: Easy programming of customized test profiles, recallable for future tests, including; Adjustable test start delay Penetration Point positions Manual or automatic penetration on rate Free or driven dropping mode Auto end-test detection Auto measurement of initial and final setting tune Test data: test number, operator, client, date, hour, cement type, water percentage, delay Clock calendar Easy Calibration menu 7.0 Automatic Triaxial Testing System (BS 377 & ASTM D280) Consisting of a load frame (00kN), Triaxial cells, Pressure controllers, software and requisite accessories Equipment required to conduct total and effective stress tests (UU, CU, CD) and stress path among other tests. Maximum number of simultaneous tests: 6 Capacity: 00kN Speed range: 0.0000 99.99999mm/minute Specimen range: 38, 0, 70, 00, 0mm diameter Pressure resolution: 0.kpa Volume resolution: 0.00cc LAN Communication Provide a complete system with all the requisite mechanical and electronic accessories, transducers, hand samplers, a Personal Computer (PC) and software and other operational components required.
7. Manual Triaxial Testing System (BS 377 & ASTM 280) Consisting of a load frame (00kN), triaxial cells (3 00mm diameter) Analogue measuring system for effective and total stress measurements (UU, CU, CD) Capacity: 00kN Pressure System (air/water and controls Panels; oil & water constant pressure system Template for data processing and reporting. Speed range: 0.0000 99.99999mm/minute Specimen range: 3, 38, 0, 70, 00mm diameter with standard triaxial cell Sampling rate: Manual with stop watch Provide a fully analogue data measuring system with all the requisite accessories ready for use. 8.0 Automatic Blaine Fineness (air permeability) Apparatus (EN 96 6) For determining the fineness of cement (and other powdery products) in terms of specific surface; A complete equipment ready for use is required blaine cell; manometric liquid (Non-toxic), standard reference material NIST 4q for calibration, filter paper discs, plastic funnel, brushes, etc. Storage Memory of at least 000 test results PC connection provision Real Time displaying of temperature, constant k, passing time and other parameters Color LCD,7 touch screen
. 9 Schmidt Rebound Test Hammer (BS 88 & ASTM C80) 6 For Non-destructive testing of concrete Spring Impact Energy of 2.2 joules Measuring range 0 to 70Mpa Supplied complete with Calibration Curve Chart, abrasive stone and carrying case. 9. Test Anvil (BS 88 & ASTM C80) For periodical Calibration of the test hammer Body made from Special alloy Steel 20 Electronic Top Loading Balance 3 Capacity: 30kg x g Battery Operated 20. Top Loading Balance 3 Capacity: 200gms x 0.0g 20.2 Top Loading Balance 3 Capacity: 400g x 0.0g 20.3 Field and Laboratory Scale Capacity: 2kg x g Supplied Complete with a scoop and a carrying case
20.4 Electronic Analytical Balance Capacity x Readability: 20 x 0.000g Linearity: 0.2mg Stabilization Time: 3 seconds Weighing pan size: 90mm Weighing Chamber height: 209mm Dimension: 360 x 26 x 320mm Draft Shield Chamber: with doors that glide smoothly, interior of spill proof design, In-use cover: For added protection against dirt Housing: Chemically resistant finish Calibration: Fully automatic, temperature and time controlled internal adjustment. Interface: Mini USB 2 Vibration Compaction Hammer (BS 377 & 924) 2 For Compaction of granular material like CRR; and asphalt in the PRD test Full load Impact rate 2800bpm 230V, Ph Supplied complete with Support frame, appropriate tampers and a shank Functional and robust design is required. 22 Heavy Duty Three gang moulds for 40 x 40 x 60mm rectangular prisms 2 For compression & Flexural tests on cement Conforms to EN 96 - Minimum surface hardness HV 400 Mould body from special alloy steel Supplied with Glass plates 220 x 90mm
23 Briquette Moulds for Ductility test of Bitumen 6 Conforms to ASTM D3 Supplied complete with base plates 24 Speedy Moisture Testers (ASTM D4944) For testing sand, soils, clays, fine & coarse aggregates, mineral ore & Concentrates, sludge and many other materials of similar consistency (up to 2mm particle size). The Kit comprises gauge, electronic balance (0-200gms), calcum carbide, measuring spoon, 2 crushing balls, brush, plastic holder cleaning cloth and carrying case Capacity: 20g Moisture range: 0-20% Gauge divisions: 0-2% 2 Marshall Compaction Moulds (ASTM D 6926 & EN 2697) 2 For use with the automatic marshall compactor Standard mould of dia 0.6mm, height 87.3mm including base plate, mould body and filling collar, all conforming to ASTM & EN standards Made from steel and projected from Corrosion. 2. Circular Paper Discs (For use with marshall compaction Moulds) 6 0mm diameter To fit the mould base before introducing mixture Pack of 000 2.2 Extraction plate (For use with Marshall compaction Moulds) 6 For removing 0.6mm specimens
2.3 Universal Specimen Extruder (BS 377/BS924) For removing asphalt specimen from Marshall moulds Capacity 0kN Maximum ram stroke: 97mm (ram) + 68mm (Screw) Steel structure with appropriate adaptors 26 Universal Multi speed Load Frame 2 Conforms to BS 377 & ASTM D883 Motorized machine with electronic digital touch screen controlled by microprocessor Suitable for all tests when the speed range is within 0.0 to 63mm/minute Maximum Load of 0kN and can perform: CBR test with a rate of.27mm/minute Marshall test with a rate of 0.8mm/minute Splitting tensile test on Marshall specimens Unconfined & Quick Triaxial tests Speed infinitely variable, easily and promptly selected. Supply a complete machine with all the required accessories for CBR and Marshall tests (penetration piston for CBR; dial gauge holder for CBR; Dial gauge 0mm travel x0.0mm; load ring 0kN; graduation and calibration chart in N; bracket device and stop safety device) and Load piston for marshall; flow meter complying with ASTM D9; Stability mould, dial gauge 0mm x 0.0mm, load ring 30kN; graduation and calibration chart in N, bracket device and stop safety device.
27. Plate Bearing Test Equipment For determining the bearing capacity of a soil insitu, designing for static loads on spread footings and repetitive and non-repetitive plate loading tests of soil and flexible pavements Loading Jack 00kN capacity with integral ball seating Pump Hand operated, single speed with integral oil reservoir Hose 3M long, maximum pressure 70Mpa with quick release couplings Gauge 00mm dia with quick release couplings and graphs to convert readings to kn. Weights loading jack 24kg - Pressure system 2.kg Plates (4No): 300mm, 40mm, 600mm, 70mm diameter. With concentric markings on one face and two lifting eyes Datum bar 2.meters Dial gauges (4No): 0mm x 0.0mm Dial gauge support assembly A complete equipment assembly is required ready for use with a reaction beam. 28. Rolling Thin- Film Oven (ASTM D2872 & EN 2607) For determining loss in mass of bituminous compounds and the effect of heat and air on a moving film of semi-solid bituminous material. Double walled electrically heated convection oven for rolling thin film oven tests on bitumen.
Door with double pane viewing window, symetrical top & bottom vents: air plenum; 72rpm fan, digital thermostat to control temperature at 63 ± 0. 0 C Air jet to blow heated air into each sample bottle. A calibrated flow meter to control air flow at 4000ml/min. Incorporates an over temperature cut off circuit Power: 230v, 0Hz, Ph Supplied complete with sample bottles for RTFO (8No), Tongs, cooling rack, Thermometer, Bottle Scrapper, Flow meter, Diaphragm pump. 29. Automatic Computerized oedometer (ACE) (BS 377,ASTM D243, AASHTO T 26) For determining rate and magnitude of consolidation of a soil Specimen restrained laterally and subjected to a number of successive increments of vertical load. Fully automatic PC controlled test execution Automated loading kn maximum loading capacity, 0mm travel displacement transducer. Real time data and graph display Supply complete equipment ready for use with: 4ACE units in series controlled by single software installation, PC for control, LAN cable, appropriate Consolidation cells
30. Splitting Tensile Test Device for Concrete Block Pavers, Concrete Cubes and Cylinders Conform to EN2390-6 & EN 338 Two Column steel frame with a self centering specimen holder at the base and an upper load beam suspended with springs To perform tests on concrete block pavers, concrete cubes, and any type of block, Prismatic specimens and cylinders. Maximum Total height is 370mm Maximum vertical day light is 20mm Minimum Vertical day light is 90mm Maximum Horizontal day light is 60mm Maximum Travel is 4mm Bearers length is 34mm Total width is 2mm Provide complete device with packing strips as follows:- Hardboard strips 4 x x 34mm to EN 2390 6 (a pack of 0) Plywood strips 3 x 2 x 34mm to ASTM C496 (a pack of 0) Provide complete device with test accessories for concrete block pavers & cubes and cylinders up to 60mm diameter x 320mm height. 3. BenKelman Beam Apparatus (AASHTO T26 & ASTM D 469) For measuring the deflection of flexible pavements under the action of moving wheel loads; Probe 2440mm long; Back extension 220mm; Manufactured from Aluminium and chrome finished metals Provide a complete set ready for use with the following accessories: wooden carrying case; spare gauge with bracket, adjustable feet for Benkelmen beam (complete with two spirit levels and a calibration device)
32. In-situ CBR Apparatus (BS 377, AASHTO T93) For determining the bearing capacity of soil quickly and efficiently during road construction. Dimension: 220x 40 x 7mm Provide a complete set consisting of a 0kN mechanical jack (single speed) c/w spherical ball attachment; extension rod set (gauge adaptor x 2, 02mm x 2, 30mm x, 60mm x & 9mm x ; penetration piston (BS); Dial gauge holder; surcharge set (slotted 9kg, 4.kg & annular 4.kg); Datum bar set (400mm long, Datum bar, tripod set and holder set); Steel carrying case; Tool kits (Spanner no.7 & Allen Key mm); Dial indicator 2 x 0.0mm; 0kN proving ring. 33 Rapid moisture Tester, 0% (BS 82, AASHTO T27 & ASTM D4944) For determing moisture content of sand, soil and fine aggregates Dimensions: 30 (L) x 280 (W) x 30 Hmm Provide a complete set consisting of Rapid bottle tester with gauge; Electrical digital balance; Bottle brush, measuring scoop, steel ball (2No.), carrying case and calcium carbide 00g (4tins). 34. Standard Density Sand (AASHTO T9 & ASTM 6) 0 For density tests Passing 600µm and retained on 300µm Pack of 0kg.
3. Filter papers (BS 377 & BS 924) For CBR testing Diameter 0mm, Pack of 00 Qualitative Grade 36. High Precision Tuning Fork Electronic Balance Capacity : 620g Readability : 0.0g Linearity : 0.0g Stabilization time : 2.0 sec Pan size : 40mm dia Calibration : External Measuring system : Tuning fork frequency sensing Display : LCD (6.mm height) Tare : Full weighing range 37. Orimas Universal mixer (set) 0 Supplied with bowl and blade Bowel capacity : 20 litres Power : 0. HP Speed : 7/26/494 RPM Weight : 90kg Dimensions : 40 x 20 x 80 (LXW x Hcm)
38. Redline Binder Oven with fan (DIN 2880) Capacity : 400 litres Configuration : Chamber Temperature Range: Room temperature plus 0 C to 300 0 C A PT line Pre heating chamber technology Adjustable fan speed and exhaust air flap Controller with expanded timer functions Class 2 independent adjustable temperature safety device with visual alarm Computer interface : RS422 Function ; drying, heating 39. Apparatus for determination of storage stability of Asphalt Emulsions Based on settlement measurement and conforms to NF T 66 022 standard; Dimensions : 200 x 200 x 00mm 230 V, ph; Provide a complete apparatus consisting of a 2V current stabilized source, stainless steel vessel of capacity 00mls, cylindrical electrode and holder. 40. Particle Charge Tester of Emulsified Asphalt (ASTM D244) For Identifying Particle charge of emulsions Provide complete apparatus and two stainless steel electrodes
4. Water in Bitumen Emulsion Test set (ASTM D244) For determination of water content of bituminous emulsions using volatile solvent Set to consist of Glass still 2mls, glass receiver, glass condenser, electric heater with thermoregulator Power : 20W, 230V, Ph 42. Cooling/Heating Circulating Bath Temperature range 20 0 C to 00 0 C Bath capacity : litres Temperature Control : PID Temperature Sensor: Pt RTD Wetted materials : stainless steel, polymers Heater wattage: Standard model 200 Watts Stability: ± 0. 0 C Cooling capacity at 20 0 c: 70W Low Level Cut off: Yes Maximum pump pressure: 300 mbar (4.4Psi) Maximum pump flow: L/Min Power : 230V, 0HZ Working area (W x LXD): 7.3 X X 8.3cm Overall Dimensions (W x LXH): 37 X 68.7 X 2cm A complete set featuring a robust refrigeration system with metering control is required ready for use.