SINCE95 RB SERIES CONTROL CHOKE Unique. Precise. Quality. Reliable.
RB SERIES CONTROL VALVES FEATURES Benefits The RB Series Control Valve features several unique design characteristics that minimize wear and maximize service life. The nozzle and external sleeve trim is designed to contain turbulence and wear by managing the flow into the nozzle and centralizing it into bore causing the flow streams to impinge on each other. The valve body and outlet are protected from wear because the energy conversion as a result of the pressure drop is concentrated in the trim cavity before flow enters the outlet. This eliminates the typical wear problems in the valve outlet. The Upstream and Downstream balanced sleeve design greatly reduces the breakway and closing thrust requirements to lift the sleeve on and off seat as well as during stem travel making the control stable and precise yielding better accuracy and repeatability. Accurate Control - Multi-Orifice Nozzle design provides precise control over a wide range of flows. Bolted Bonnet - A bolted bonnet prevents corrosion, cross-threading and galling of large threaded connections. The design allows for simple assembly and disassembly. Extended Mean Time Between Service - Robust design, application of hardened materials, and efficient flow geometry results in maximum production potential and minimum service requirements. Easy Maintenance - All Control Choke Valves are designed with special actuator mounting systems so the choke can be maintained without disassembly of the actuator and components or instrument connections. High Turndown Ratio - Clean flow geometry, high capacity and accurate control means the valve is suitable for both start-up and end-of field-life-process scenarios. In short, our control choke valves offer a one-valve solution for the full process life. Optional Features - Control Valves can have trims and actuators custom designed for specific requirements. Such as special noise reduction trims, reduced port and maximum orifice trims for very high pressure or minimum pressure loss for a declining field. Applications: Well Site Automated and Manual Application Water Injection Control Valve CO Injection Control Valve High Pressure Drop Applications Gas Lift Injection Control WWW.TAYLORVALVE.COM
Dynamic Energy Conversion Protective Outer Cage Inlet Inlet Seat Flow Diverter Nozzle Valve Body Side view of the fluid flow through the valve Flow converging in the center of the nozzle When the valve is open and flow enters through the inlet of the valve into the protective cage, it is circulated around the annulus created by the cage, nozzle and sleeve assembly. The symmetry of the ports in the nozzle cause the high velocity fluid streams created by the pressure drop to collide into each other in the center of the trim. The impact of the streams converts the energy and protects the downstream components from damage.
Multi-Orifice Nozzle Technology Control Element The RB Series valve features several unique design characteristics that minimize wear and maximize service life. The nozzle and external sleeve trim is designed to contain turbulence and wear by managing the flow into the nozzle and centralizing it into bore causing the flow streams to impinge on each other. The valve body and outlet are protected from wear because the energy conversion as a result of the pressure drop is concentrated in the trim cavity before flow enters the outlet. This eliminates the typical wear problems in the valve outlet. The upstream and downstream balanced sleeve design greatly reduces the breakaway and closing thrust requirements to lift the sleeve on and off seat as well as during stem travel making the control stable and precise yielding better accuracy and repeatability. Cage Inlet Flow circulates in the trim, jet streams impinge in the centerline and is directed to the outlet. Outer Sleeve Inner Sleeve Seat Face Seat Face Control Surface Outlet Nozzle
RB Control Valves CLOSED POSITION Debris space and liquid seal Stainless Steel Outer Cage Replaceable Seat OPEN AND THROTTLING Tri-Seat Sealing Technology Outer Protective Cage The Trim configuration has been field-tested and proven to deliver superior wear resistance and performance. The trim controls high velocity fluid during pressure reduction by directing the flow to the center of the flow nozzle. The Erosive Energy is contained within the expendable trim components away from the valve wall which is additionally protected by a replaceable sleeve, reducing the potential for release of fluids to the environment. The seat and Tri-seating surfaces on the sleeve are separate from the controlling surfaces and out of the flow path to maintain an ANSI class V shut off. Outer Sleeve Inner Sleeve Nozzle Tungsten Carbide Tungsten Carbide 7. PH Stainless Steel 7. PH Stainless Steel Tri-Seat is protected from flow erosion Control Surface separate from Sealing Surface Sealing surface out of normal flow path and protected from erosion Tri-Seat provides ANSI Class V Seal Control Surface separate from shut off seal CLOSED POSITION OPEN AND THROTTLING Replaceable flow nozzle is the wear component 5
RB Cutaway View RB Control Choke Cv = 6,, 5 (Standard) Bean Size = 7 / 6th s (Standard) Stroke Length =.5 Stem Diameter = 0.65 MAWP = 0,000 PSIG MANUAL C ** 9** 0** ** 7** 6 A 6*** 9 9 5 B ITEM DESCRIPTION O-RING -0 O-RING - O-RING - The information contained in these drawings is the sole property of Taylor Valve Technology Inc. and any reproduction in part or whole without the written permission of Taylor Valve Technology Inc. is prohibited. 5 0** 7 5 7 6 0 O-RING -0 5 O-RING -5 6* DOWEL PIN 7 DOWEL PIN STUD 9 HEX NUT 0** HEX BOLT * SET SCREW HEX NUT (Lock Nut) VENT VALVE NOZZLE 5 SEAT 6 CAGE 7 EXTERNAL SLEEVE ASSEMBLY EXTERNAL SLEEVE GUIDE 9 BONNET 0 BODY/FLANGE WELDMENT STEM YOKE LOCK NUT WASHER SNAP RING 5 U-CUP SEALS 6*** YOKE 7** ANTI-ROTATIONAL DEVICE ** STEM ADAPTER 9** PIPE PLUG 0** DIAMOND GEAR ACTUATOR ** HANDWHEEL WIPER SEAL (Dust Cap) BACK UP RINGS *Item not visible in sectioned view **Parts not included on actuator ***Optional depending on actuator type (Contact TVT for information) QTY 6 6
RB Control Valves RB Dimensions and Weights CONNECTIONS DIMENSIONS - IN. (MM.) WEIGHT INLET OUTLET "A" "B" "C" LB. KG. " BW " BW.50 ().50 ().0 (57) 0 6 " 00 RFF " 00 RFF 7.5 () 7.5 () 5.5 (657) 96 " 600 RFF " 600 RFF 7.6 (9) 7.6 (9) 6. (666) 00 5 " 600 RTJ " 600 RTJ 7.69 (95) 7.69 (95) 6.9 (66) 00 5 " 900/500 RTJ " 900/500 RTJ. (). () 7. (696) 5 " 500 RTJ " 500 RTJ 9. (9) 9. (9). (7) 6 7 " BW " BW.50 ().50 ().0 (57) 0 6 " 00 RFF " 00 RFF 7.6 (9) 7.6 (9) 6. (666) 0 50 " 600 RFF " 600 RFF.00 (0).00 (0) 6.60 (676) 6 57 " 900 RTJ " 900 RTJ. (). () 7. (696) 6 " 500 RFF " 500 RFF 9. () 9. () 7.9 (7) 76 0 " 500 RTJ " 500 RTJ 9. (0) 9. (0).0 (7) 76 0 " 500 RTJ " 500 RTJ. (90). (90) 0.0 (76) 6 -/6 API 5000 -/6 API 5000. (). () 7. (696) 5 -/6 API 0000 -/6 API 0000 9.0 (9) 9.0 (9) 7.6 (70) 55 -/6 API 5000 -/6 API 5000 9.0 (9) 9.0 (9) 7.6 (70) 55-9/6 API 5000-9/6 API 5000.9 (7).9 (7) 7.5 (700) 5 70-9/6 API 0000-9/6 API 0000 9.5 () 9.5 (). (7) 50 6-9/6 API 5000-9/6 API 5000 9.5 () 9.5 (). (7) 50 6 -/ API 5000 -/ API 5000 9. (0) 9. (0).0 (7) 76 0 -/ API 0000 -/ API 0000 9.5 () 9.5 (). (7) 0 -/ API 5000 -/ API 5000 9.5 () 9.5 () 0.5. (5) 96 5 ALL DIMENSIONS ARE +/-.0 0 RB CV vs % OPEN (Standard Trim) 5 0 5 TOP OF HANDWHEEL (0) Cv 0 5 0 5 0 0 0 60 0 00 % OPEN NOTE: Taylor Valve reserves the right to change product designs and specifications without notice. 7
RB Cutaway View RB Control Choke Cv = 5, 6 (Standard) Bean Size = 05 / 6th s Stroke Length =.75 Stem Diameter = 0.65 MAWP = 6,000 PSIG MANUAL C ** 9** 0** ** 7** A 6*** 9 9 5 B ITEM DESCRIPTION O-RING -7 O-RING - O-RING -0 The information contained in these drawings is the sole property of Taylor Valve Technology Inc. and any reproduction in part or whole without the written permission of Taylor Valve Technology Inc. is prohibited. 5 0** 7 5 5 7 6 0 O-RING - 5 O-RING -5 6* DOWEL PIN 7 DOWEL PIN STUD 9 HEX NUT 0** HEX BOLT * SET SCREW HEX NUT (Lock Nut) VENT VALVE NOZZLE 5 SEAT 6 CAGE 7 EXTERNAL SLEEVE ASSEMBLY EXTERNAL SLEEVE GUIDE 9 BONNET 0 BODY/FLANGE WELDMENT STEM YOKE LOCK NUT WASHER SNAP RING 5 U-CUP SEALS 6*** YOKE 7** ANTI-ROTATIONAL DEVICE ** STEM ADAPTER 9** PIPE PLUG 0** DIAMOND GEAR ACTUATOR ** HANDWHEEL WIPER SEAL (Dust Cap) BACK UP RINGS *Item not visible in sectioned view **Parts not included on actuator ***Optional depending on actuator type (Contact TVT for information) QTY
RB Control Valves INLET " BW " 50 RFF " 00 RFF " 600 RFF " 600 RTJ " 900 RFF " 900 RTJ " 500 RFF " 500 RTJ " 500 RFF " 500 RTJ " BW " 50 RFF " 00 RFF " 600 RFF " 600 RTJ " 900 RFF " 900 RTJ " 500 RFF " 500 RTJ " 500 RFF " 500 RTJ -/ API 000 -/ API 5000 -/6 API 000 -/6 API 5000 ALL DIMENSIONS ARE +/-.0 RB Dimensions and Weights CONNECTIONS OUTLET " BW " 50 RFF " 00 RFF " 600 RFF " 600 RTJ " 900 RFF " 900 RTJ " 500 RFF " 500 RTJ " 500 RFF " 500 RTJ " BW " 50 RFF " 00 RFF " 600 RFF " 600 RTJ " 900 RFF " 900 RTJ " 500 RFF " 500 RTJ " 500 RFF " 500 RTJ -/ API 000 -/ API 5000 -/6 API 000 -/6 API 5000 "A" 5.5 ().00 (0). ().75 (). () 9.50 () 9.56 () 0. (57) 0.9 (59). (0).5 () 5.5 ().5 (0).6 (9) 9.50 () 9.56 () 0.00 (5) 0.06 (56) 0. (6) 0. (65).00 (0).9 (5) 9.56 () 0.9 (5) 0.06 (55) 0. (65) DIMENSIONS - IN. (MM.) "B" 5.5 ().00 (0). ().75 (). () 9.50 () 9.56 () 0. (57) 0.9 (59). (0).5 () 5.5 ().5 (0).6 (9) 9.50 () 9.56 () 0.00 (5) 0.06 (56) 0. (6) 0. (65).00 (0).9 (5) 9.56 () 0.9 (5) 0.06 (55) 0. (65) "C". (7) 0.7 (7).5 (79).6 (0).6 (05).7 (). ().00 ().06 (0) 5.00 (9) 5. (9). (7). (790).9 (00).7 (). ().7 (5).9 (6).5 (5). (6) 5.7 (9) 6.06 (96). ().06 (0).9 (6). (6) LB. 5 77 5 90 90 50 50 5 7 07 56 56 9 9 50 56 9 WEIGHT KG. 70 0 6 6 96 96 55 55 70 5 9 0 0 6 6 0 0 96 6 70 RB CV vs % OPEN (Standard Trim) 60 50 0 Cv 0 0 0 0 0 0 0 0 0 50 60 70 0 90 00 % OPEN 9
RB Cutaway View RB Control Choke Cv = 6 Bean Size = 69 / 6th s Stroke Length =.5 Stem Diameter =.75 MAWP = 6,000 PSIG MANUAL C ** 9** 0** ** 7** 0** 0 A 6*** 9 9 5 B ITEM DESCRIPTION O-RING -6 O-RING -5 O-RING -7 The information contained in these drawings is the sole property of Taylor Valve Technology Inc. and any reproduction in part or whole without the written permission of Taylor Valve Technology Inc. is prohibited. 5 7 5 5 7 6 0 O-RING -9 5 O-RING - 6* DOWEL PIN 7 DOWEL PIN STUD 9 HEX NUT 0** HEX BOLT * SET SCREW HEX NUT (Lock Nut) VENT VALVE NOZZLE 5 SEAT 6 CAGE 7 EXTERNAL SLEEVE ASSEMBLY EXTERNAL SLEEVE GUIDE 9 BONNET 0 BODY/FLANGE WELDMENT STEM YOKE LOCK NUT WASHER SNAP RING 5 U-CUP SEALS 6*** YOKE 7** ANTI-ROTATIONAL DEVICE ** STEM ADAPTER 9** PIPE PLUG 0** DIAMOND GEAR ACTUATOR ** HANDWHEEL WIPER SEAL (Dust Cap) BACK UP RINGS *Item not visible in sectioned view **Parts not included on actuator ***Optional depending on actuator type (Contact TVT for information) QTY
RB Control Valves INLET " BW " 50 RFF " 00 RFF " 600 RFF " 600 RTJ " 900 RFF " 900 RTJ " 500 RFF " 500 RTJ " 500 RFF " 500 RTJ 6" BW 6" 50 RFF 6" 00 RFF 6" 600 RFF 6" 600 RTJ 6" 900 RFF 6" 900 RTJ 6" 500 RFF 6" 500 RTJ 6" 500 RFF 6" 500 RTJ -/6 " 000 API -/6 " 5000 API ALL DIMENSIONS ARE +/-.0 RB Dimensions and Weights CONNECTIONS OUTLET " BW " 50 RFF " 00 RFF " 600 RFF " 600 RTJ " 900 RFF " 900 RTJ " 500 RFF " 500 RTJ " 500 RFF " 500 RTJ 6" BW 6" 50 RFF 6" 00 RFF 6" 600 RFF 6" 600 RTJ 6" 900 RFF 6" 900 RTJ 6" 500 RFF 6" 500 RTJ 6" 500 RFF 6" 500 RTJ -/6 " 000 API -/6 " 5000 API "A" 6.50 (65) 9.50 () 9. (5) 0.75 (7) 0. (75).5 (6). (7).6 (95).69 (97).5 (6). (67) 6.50 (65) 0.00 (5) 0. (6). (9). (9).5 (). ().50 ().6 (6) 7.50 (5) 7.75 (5). (7).69 (97) RB CV vs % OPEN (Standard Trim) DIMENSIONS - IN. (MM.) "B" 6.50 (65) 9.50 () 9. (5) 0.75 (7) 0. (75).5 (6). (7).6 (95).69 (97).5 (6). (67) 6.50 (65) 0.00 (5) 0. (6). (9). (9).5 (). ().50 ().6 (6) 7.50 (5) 7.75 (5). (7).69 (97) "C". (7) 7. (99) 7.76 (959).6 (9).69 (9) 9. (99) 9.9 (995) 9.5 (00) 9.57 (005). (070). (075). (7) 7. (96).6 (97) 9.6 (997) 9. (999) 0. (09) 0.9 (0). (05).50 (05) 5. (5) 5.6 (59) 9.9 (995) 9.57 (005) LB. 67 97 7 5 5 79 79 55 55 669 669 67 5 5 59 59 597 597 705 705 79 55 WEIGHT KG. 66 0 9 05 05 7 7 0 0 66 05 0 0 7 7 0 0 5 5 7 Cv 0 60 0 0 00 0 60 0 0 0 0 0 0 0 50 60 70 0 90 00 % OPEN
RB6 Cutaway View RB6 Control Choke Cv = 0 Bean Size = 70 / 6th s Stroke Length =.5 Stem Diameter =.00 MAWP = 6,000 PSIG 9** MANUAL C 7** ** 6** 5** A *** 0 7 0 B ITEM DESCRIPTION O-RING -6 O-RING -69 O-RING -55 The information contained in these drawings is the sole property of Taylor Valve Technology Inc. and any reproduction in part or whole without the written permission of Taylor Valve Technology Inc. is prohibited. 0 7 6 6 5 9 O-RING -67 5* DOWEL PIN 6 DOWEL PIN 7 STUD HEX NUT 9* HEX BOLT 0* SET SCREW HEX NUT (Lock Nut) VENT VALVE NOZZLE SEAT 5 CAGE 6 EXTERNAL SLEEVE ASSEMBLY 7 EXTERNAL SLEEVE GUIDE BONNET 9 BODY/FLANGE WELDMENT 0 STEM WASHER SNAP RING U-CUP SEALS *** BRACKET 5** ANTI-ROTATIONAL DEVICE 6** STEM ADAPTER 7** PIPE PLUG ** DIAMOND GEAR ACTUATOR 9** HANDWHEEL 0 WIPER SEAL (Dust Cap) BACK UP RINGS STUD NUT *Item not visible in sectioned view **Parts not included on actuator ***Optional depending on actuator type (Contact TVT for information) QTY
RB Control Valves ALL DIMENSIONS ARE +/-.0 RB6 Dimensions and Weights CONNECTIONS INLET 6" BW 6" 50 RFF 6" 00 RFF 6" 600 RFF 6" 600 RTJ 6" 900 RFF 6" 900 RTJ 6" 500 RFF 6" 500 RTJ 6" 500 RFF 6" 500 RTJ " BW " 50 RFF " 00 RFF " 600 RFF " 600 RTJ " 900 RFF " 900 RTJ " 500 RFF " 500 RTJ " 500 RFF " 500 RTJ 7-/6 API 000 7-/6 API 5000 OUTLET 6" BW 6" 50 RFF 6" 00 RFF 6" 600 RFF 6" 600 RTJ 6" 900 RFF 6" 900 RTJ 6" 500 RFF 6" 500 RTJ 6" 500 RFF 6" 500 RTJ " BW " 50 RFF " 00 RFF " 600 RFF " 600 RTJ " 900 RFF " 900 RTJ " 500 RFF " 500 RTJ " 500 RFF " 500 RTJ 7-/6 API 000 7-/6 API 5000 "A" 9.50 ().00 (0). (0). (65). (6) 5.5 (7) 5. (9) 6.50 (9) 6.6 () 0.50 (5) 0.75 (57) 9.50 ().50 (). (5) 5.00 () 5.06 () 6. (0) 6.9 (). (6). (65).5 (565).56 (57) 5. (9) 6.6 () DIMENSIONS - IN. (MM.) "B" 9.50 ().00 (0). (0). (65). (6) 5.5 (7) 5. (9) 6.50 (9) 6.6 () 0.50 (5) 0.75 (57) 9.50 ().50 (). (5) 5.00 () 5.06 () 6. (0) 6.9 (). (6). (65).5 (565).56 (57) 5. (9) 6.6 () "C".5 (5) 7.0 (9) 7. (950). (976). (977) 9.9 (99) 9.5 (999) 0.5 (00) 0.66 (0).5 ().79 ().5 (5) 7.5 (95) 7.9 (96) 9.0 (99) 9.0 (99) 0.7 (00) 0. (0).7 (07).5 (076) 6.9 (76) 6.60 () 9.5 (999) 0.67 (0) WEIGHT LB. KG. 767 5 5 99 99 00 00 59 59 767 5 90 007 007 57 57 9 9 95 95 57 9 70 6 55 55 50 50 699 699 09 57 57 55 55 60 60 7 7 55 60 RB6 CV vs % OPEN 50 (Standard Trim) Cv 00 50 00 50 00 50 00 50 0 0 0 0 0 0 50 60 70 0 90 00 % OPEN
RB Actuation Packages Electric Actuators Multi - Turn IQTF 5 Rotork Volt DC Supply Max Torque 9 ft. lbs. Side Mounted Hand wheel Weight 9 lbs. Used on RB & IQTF 50 Rotork Volt DC Supply Max Torque 0 ft. lbs. Side Mounted Hand wheel Weight 9 lbs. Used on RB & IQS 5 Rotork Single Phase Supply (0v or 0v) Max Torque 0 ft. lbs. Top Mounted Hand wheel Appx. Weight 60 lbs. Used on RB, & 6 Pneumatic Actuators Spring Cylinder Valtek VL 50* Double Acting Configuration Actuation Air Pressure Max 0psi Optional Manual Hand Wheel Used on RB *Valtek VL00 also available for RB & RB 6 Valtek VL 5* Double Acting Configuration Actuation Air Pressure Max 0psi Optional Manual Hand Wheel Used on RB *Valtek VL00 also available for RB & RB 6 Valtek VL 00 Double Acting Configuration Actuation Air Pressure Max 0psi Optional Manual Hand Wheel Used on RB 6 Note: Actuators shown are not manufactured by Taylor Valve, but bought as per customer requested specifications for their applications/installations. Consult Taylor Valve for more options.
RB Actuation Packages Pneumatic Actuators Spring Diaphragm Fisher Pneumatic Spring Diaphragm Fisher Pneumatic Spring Diaphragm Single or Double Acting Configuration Actuation Air Pressure 0psi Used on R & RB Single or Double Acting Configuration Actuation Air Pressure 0psi Used on R & RB Dynaflo Pneumatic Spring Diaphragm Single or Double Acting Configuration Actuation Air Pressure -0psi Used on RB Dynaflow Pneumatic Spring Diaphragm Fisher Pneumatic Spring Diaphragm Single or Double Acting Configuration Actuation Air Pressure -0psi Used on RB Kimray Pneumatic Spring Diaphragm Single or Double Acting Configuration Actuation Air Pressure 0psi Used on RB & Single or Double Acting Configuration Actuation Air Pressure -0psi Used on RB Note: Actuators shown are not manufactured by Taylor Valve, but bought as per customer requested specifications for their applications/installations. Consult Taylor Valve for more options. 5
Choke Nomenclature Choke Series CA CI MC MCX MDA MDAS MDI MDIS RB R Size 6 6 Service Type 0 Standard NACE Steam/High Temp. Actuation Type 0 Manual Handle Manual Gear Electric Pneumatic Hydraulic 7 Positive Bean Style 0 Non-flanged RFF RTJ RFF X RTJ RTJ X RFF Schedule 0 Non-flanged 0 0 60 XS 5 XXS 6 SLIP-ON 7 API 0 Trim Material 0 CARBIDE DISC - STELLITE WR SLV 0 CERAMIC DISC - STELLITE WR SLV 05 CARBIDE DISC - CARBIDE WR SLV 5 CERAMIC DISC - NO WR SLV 6 CARBIDE DISC - NO WR SLV CERAMIC DISC/CARBIDE TUBE R/RB-SERIES 7 BEAN 7- SS Body Material 00 DUPLEX SS 0 CARBON STEEL 0 LOW ALLOY (0 LACS) 05 6 SS (CFM) 06 6 SS "L" (CFM) 07 ALUMINUM BRONZE 0 A50 LF 09 LCC SUPER DUPLEX SS RB 0 9 9 60 0 0 = RB-0996000 EXAMPLE ONLY* Choke part number has to be 7 digits. Inlet Connection Outlet Connection 0 " FNPT 0 " BUTT WELD 0 " SOCKET WELD 0 " VICTAULIC 05 " 50 06 " 00 07 " 600 0 " 900/500 09 " 500 0 " FNPT " BUTT WELD " SOCKET WELD " VICTAULIC 5 " 50 6 " 00 7 " 600 " 900/500 9 " 500 0 " FNPT " BUTT WELD " SOCKET WELD " 50 " 00 5 " 600 6 " 900 7 " 500 " 500 9 " FNPT 0 " BUTT WELD " SOCKET WELD " VICTAULIC " 50 " 00 5 " 600 6 " 900 7 " 500 " 500 9 6" 50 0 6" 00 6" 600 6" 900 6" 500 6" 500 5 " 50 6 " 00 7 " 600 " 900 9 " 500 50 " 500 5 -/6" 000 5 -/6" 5000 5 -/6" 0000 5-9/6" 000 55-9/6" 5000 56-9/6" 0000 57 -/" 000 5 -/" 5000 59 -/" 0000 60 -/6" 000 6 -/6" 5000 6 -/6" 0000 6 -/6" 5000 6 /" 600# 65.5" 900/500 66 -/6" 0000 67 7-/6" 5000 6 -/6" 5000 69 -/6" 5000 75 " UNION 76 " 60M x " 60F Union 0 0" 600 0" 900 0" 500 0" 500-9/6" 5000 5 6" Butt Weld Orifice Size 0 () /" RND PORTS 0 () /6" RND PORTS 0 () /" RND PORTS 0 () /" RND PORTS 05 () /" RND PORTS 06 () 5/" PIE PORTS 07 () /" RND PORTS 0 () 7/" RND PORTS 0 () -/6" RND PORTS () -/" RND PORTS () -/" RND PORTS 0 () /" PIE PORTS 5 () " ROUND PORTS () " PIE PORTS 0 () -/" PIE PORTS () -/" PIE PORTS () -/" RND PORTS 7 () -/ PIE PORTS 9 () 5/" RND PORTS 5 ().9 PIE HOLES 55 CV 56 CV 57 6 CV 5 0 CV 59 6 CV 60 5 CV 7/6 BEAN /6 BEAN /6 BEAN 5 /6 BEAN 6 /6 BEAN 7 /6 BEAN 6/6 BEAN *For more options, contact Taylor Valve. 9 /6 BEAN /6 BEAN 0/6 BEAN /6 BEAN 5 /6 BEAN 6 0/6 BEAN 5 0/6 BEAN 6 /6 BEAN 6 /6 BEAN 65 5/6 BEAN 66 6/6 BEAN 67 9/6 BEAN 6 0/6 BEAN 69 /6 BEAN 70 /6 BEAN 7 /6 BEAN 7 /6 BEAN 7 7/6 BEAN 7 9/6 BEAN 75 5/6 BEAN 76 /7" RND PORTS 77 7/6 BEAN 7 5/6 BEAN 79 /6 BEAN 0 5/6 BEAN 7/6 BEAN 5/6 BEAN 5/6 BEAN 7/6 BEAN 5 6 CV 7 /6 BEAN 7 CV Seal Material 00 HNBR/HSN 0 NBR 0 EPDM 0 FKM (VITON) 05 NEOPRENE 06 NBR (PEROXIDE CURED) 07 STEAM SEALS 09 AFLAS KALREZ PINS I INCONEL (Optional) Butt weld connections MUST specify a schedule. All API connections are RTJ style by default. API flange bore (SCHEDULE) is specified by API. REVISED: 0-05-7 Taylor Valve Technology 00 S.W. th Street Oklahoma City, Oklahoma 7 TEL FAX 05.77.05 00.05.0 WEB EMAIL www.taylorvalve.com info@taylorvalve.com