Parts List for: Form No. 068 SPX Corporation 88 th Street Rockford, IL 609-699 USA Internet Address: http://www.powerteam.com Tech. Services: (800) 77-826 Fax: (800) 76-826 Order Entry: (800) -8 Fax: (800) 288-70 PA6R-MILL MODEL F AIR HYDRAULIC PUMP Max. Capacity: 0,000 PSI (700 Bar) 2 *8 Reservoir Gasket 2 62 Reservoir *09 Decal 20 Straight Fitting 2060 6 Hex Washer Hd Screw (#9- X " Lg.; Torque to 2/ in. lbs.) PARTS INCLUDED BUT NOT SHOWN 2060 Hex Washer Hd Screw (#9- X " Lg.; For pump mounting purposes only) Part numbers marked with an asterisk (*) are contained in Repair Kit No. 0088. Sheet No. of Litho in USA Rev 8 Date: Nov 200
Parts List, Form No. 068, Back sheet of TOP AND END VIEW, 2 0 8, 9 2 7 Apply Permatex between gasket and cover plate 6 2 Soc. Hd. Cap Screw (0-2 UNC X /2 Lg.) 2 089 2 Washer (#0 bolt) 20 Straight Fitting 2096BK2 Cover Plate 6 Soc. Hd. Cap Screw (0-2 UNC X -/" Lg.; Torque to 0/60 in. lbs.) 6 2029 Valve Body 7 868 Release Valve Body 8 20 Elbow 9 20928 Plastic Cap 0 2689 Filler/Breather Cap *027 2 O-ring (/6 X /8 X /2; Nitrile) 2 6767 Pump Body 728 Soc. Hd. Cap Screw (/-20 UNC X -/2" Lg.; Torque to 8/9 in. lbs. oiled; NOTE: Cross torque in increments of 0 in. lbs.) Part numbers marked with an asterisk (*) are contained in Repair Kit No. 0088.
Parts List Form No. 068 BASIC PUMP ASSEMBLY To Parts List 9 0 See Detail "A" 2 2 8 6 7 7 8, 9 0 2 6,2 22 0 29 28 27 26 2 2 22 2 2 9 7 8 20; See Detail "B" 6 DETAIL "B" Sheet No. 2 of Rev 8 Date: Nov 200
Parts List, Form No. 068, Back sheet 2 of 77 Piston Release 2 *208 O-ring (-/8" X 7/8 X /8; Apply Lubricant) *0272 O-ring (/ X 9/6 X /2; Nitrile) 78 Check Valve Body *222 2 O-ring (/8 X / X /6; Urethane) 6 *8 O-ring (-/8" X -/8" X /8; Nitrile) 7 *02 Gasket 8 *02 Washer (/8 X / X /2) 9 0002 Soc. Hd. Cap Screw (/-20 UNC X /8 Lg.; Torque to 90/0 in. lbs.) 0 *0 Compression Spring (/2 O.D. X / Lg.) *02 Steel Ball (9/2 Dia.) 2 2278 Relief Valve (Apply loctite 92 [Power Team #906] or equiv. & torque to 0/70 in. lbs.) 278 Piston Cylinder (Torque to 90/00 ft. lbs. oiled) *07 Steel Ball (/ Dia.) *026 Copper Washer (/ X 9/2 X /2) 6 0889 Filter Adapter 7 278 Filter 8 286 Internal Retaining Ring 9 *026 Copper Washer (" X.76 X /2) 20 2 *9 *029 U-cup & Backup Retainer (Note: See INSTRUCTIONS FOR RETAINER REPLACEMENT on back sheet of.) 22 *729 2 Back-up Ring (2-/6" X 2-/" X.0) 2 *98 Compression Spring (.2 O.D. X -7/6" Lg.) 2 28226 Piston 2 20 Bumper 26 2099 Spring Guide 27 7 Air Cylinder (NOTE: Locate groove on upper half (top) of pump with chamfered tube end towards rear head as shown.) 28 *2692 Compression Spring (/6 O.D. X -/6" Lg.) 29 *202 O-ring (.900 X.706 X.097; Nitrile) 0 07 Exhaust Valve Stem *02 Lockwasher (For #0 bolt) 2 20 Screw (#0-2 X /2 Lg.; Torque to 0/ in. lbs.) 822 Piston End Plate *288 Piston Poppet *20679 Compression Spring (.8 O.D. X.9 Lg.) 6 *2067 Hex Soc. Flat Hd. Cap Screw (8-2 UNC X /8 Lg.; Torque to 2/8 in. lbs.) 7 768 Rear Head 8 *26296 Filter Disc 9 *206 Muffler 0 *2829 Gasket 290 Piston Body 2 *26 2 Piston Ring *28 2 O-ring (2-/2" X 2-/6" X /2; Nitrile) *0276 O-ring (" X / X /8; Nitrile) To Drawing Part numbers marked with an asterisk (*) are contained in Repair Kit No. 0088.
Parts List Form No. 068 DETAIL A 2 Seat at ass'y. 6 7 8 9 0 28227 Release Valve Button 2 *0266 O-ring (/8 X / X /6; Nitrile) *9 Spring 77 Poppet Retainer *279 O-ring (/2 X /8 X /6; Nitrile) 6 97 Dowel Pin (NOTE: Place tapered end toward ball.) 7 2907 Release Valve Body 8 * Steel Ball (/2 Dia.) 9 20976 Ball Retainer 0 *99 Compression Spring (/8 O.D. X /2 Lg.) Part numbers marked with an asterisk (*) are contained in Repair Kit No. 0088. Refer to any operating instructions included with this product for detailed information about operation, testing, disassembly, reassembly, and preventive maintenance. Items found in this parts list have been carefully tested and selected. Therefore: Use only genuine Power Team replacement parts! Additional questions can be directed to our Technical Services Department. Sheet No. of Rev 8 Date: Nov 200
Parts List, Form No. 068, Back sheet of INSTRUCTIONS FOR RETAINER REPLACEMENT Your pump's retainer is locked into place by one of the two following methods. Determine which method was used on your pump's retainer, then follow the appropriate steps to remove the old and install and stake the new. Method - Retainer shows no sign of stake marks. This retainer has been locked in place with a Loctite product. To replace it, a moderate amount of heat needs to be applied to the cylinder nut (in the area of the retainer) to soften the existing Loctite allowing it to be removed. 2. Install the new retainer into the cylinder nut and torque to 80/00 in. lbs. Note: Do not use a Loctite product this time but stake the new retainer in place according to instructions in Step.. To lock retainer into place, use a center punch positioned in the seam between the retainer and the cylinder nut and stake the new retainer in two places approximately 80 apart. Method 2 - Retainer has two stake marks in the seam between the retainer and the cylinder nut. For replacement of this retainer, the stake marks must be removed. Using a /8" or larger diameter drill bit, remove the existing stakes by drilling a short distance into the stake marks. Remove the retainer. 2. Install the new retainer into the cylinder nut and torque to 80/00 in. lbs.. To lock retainer into place, use a center punch positioned in the seam between the retainer and the cylinder nut and stake the new retainer in two places approximately 80 apart. NOTE: Do not stake in the old stake marks. Thread seam Cylinder nut Retainer Stake marks No stake marks