Matrix_Techdata_SS_V4
CONTENTS V4 SPECIFICATIONS Page Features & Applications Typical Exploded View Pump & Motor Specifications Selection Chart / Type key 3 Selection Chart 4 PERFORMANCE CURVES Performance Curve Matrix 33/.65, 34/.65, 35/.75, 36/.9 Performance Curve Matrix 54/.9, 55/.3, 56/.3 Performance Curve Matrix 4/.5, 5/. Performance Curve Matrix 83/. 3 CONSTRUCTIONS Constructions 3 Constructions Mechanical Seal 3 DIMENSIONS Dimensions and Weight Packing Dimensions and Weight TECHNCAL DATA Technical Data Motor, Bearing and noise data 5
FEATURES AND APPLICATIONS V4 Bare Pump Automatic Pressure System (Presscontrol) Pressure System (Pressure Switch, Tee piece and gauge) Horizontal multistage centrifugal electric pumps in stainless steel suitable for household and commercial water boosting, distribution and treatment of water, irrigation and recovery of rain water etc. Strong and compact construction. Available as pressure systems. Specifications Maximum working pressure : bar Liquid temperature: 5 C to 85 C Supply Materials.8 m cable & plug with phase models Pump casing: 34 Stainless Steel Intermediate casings: 34 Stainless Steel Impellers: 34 Stainless Steel Casing cover: 34 Stainless Steel Shaft : 34 Stainless Steel Bracket & Motor frame: Aluminium Mechanical seal: Carbon/Ceramic/EPDM Motor Data TEFC, pole motor Insulation class F IP55 protection 5 Hz, phase 3 Volt In built overload protection for phase Range.65 to. kw phase Options Available as pressure systems
TY PICAL EXPLODED V IEW V4 # only 83/.M Mounting arrangement for. kw ph. motors
PUMP AND MOTOR SPECIFICATIONS V4 PUMP Liquid Handled Type of liquid Water, mildly aggressive solutions Max temperature [ C] 85 Min temperature [ C] 5 Max. chlorine content 5 ppm Maximum pressure [MPa] Impeller Closed centrifugal type Construction Motor bearings Screened ball bearing greased for life n 789 impellers (Matrix 35) Type: Sleeve Pump Bearings n 6 impellers (Matrix ) Shaft sleeve: Tungsten Carbide n 56 impellers (Matrix 8) Bearing: Ceramic Pipe Connection Suction/Disharge 3 G " G " ( threads according ISO 8) 5 G ¼ G " G ½ G ¼ 8 G G ½ Material Casing EN.43 () Impeller EN.43 () Intermediate casing EN.43 () ORings EPDM Casing cover EN.43 () Shaft seal Ceramic/Carbon/EPDM Liner ring EN.43 () + PTFE Shaft (wet extension) EN.43 () Bracket EN ABAlSiCu(Fe) (Die cast Aluminium) Applicable standard of test ISO 996 Annex A Approval for drinking water application WRAS Approved product DM74/4 MOTOR Type No. of Poles Insulation Class Max ambient temperature [ C] Protection degree Power rating [kw] [HP] Frequency [Hz] Voltage [V] Capacitor Overload protection Casing material Base material/motor support Dimensions of cable entry Electric asynchronous TEFC Single Phase F IP 55.65..9 3. 5 3 ±% Built in Built in Aluminium Aluminium PG Mx.5
SELECTION CHART V4 Pump type Single phase 33T /.65M 34T /.65M 35T /.75M 36T /.9M 54T /.9M 55T /.3M 56T /.3M 4T /.5M 5T /.M 83T /.M Motor Q=Capacity Power l/min 3 45 6 8 3 6 5 3 35 45 kw HP m 3 /h..8.7 3.6 4.8 6 7.8 9.6 5 8 4 7 H=Total manometric head in meters.65.9 33.9 3.4 9.3 5.5.4..65.9 45. 4. 39. 34. 7. 6..75. 56.5 5.5 49. 4.5 34...9. 68. 6.5 58.5 5. 4. 4..9. 46. 43. 4. 38.6 34.7 9.4 7.6.3.8 57.5 54. 5. 48.5 43.5 36.7..3.8 69. 64.5 6.5 58. 5. 44. 6.4.5. 48. 44.5 43. 4. 38. 34. 5.7.6. 3. 6. 55.5 53.5 5.5 47.5 4.5 3. 4.5. 3. 36.3 33. 3.9 3.4 8. 5..3 5.5 7.8 Type Key : 3 6 T /.9 M Single phase only Motor output in kw.65.75.9.3.5. T : Threaded pipe connection No.of impellers 3 4 5 6 m 3 /h at max.efficiency 3 5 8 Model series 3
SELECTION CHART V4 7 6 Total Head (m) 5 3 36T/.9M 35T/.75M 34T/.65M 33T/.65M 56T/.3M 55T/.3M 54T/.9M 5T/.M 4T/.5M 83T/.M 5 3 5 6 7 8 5 3 5 Capacity (lpm) Curve specifications The specifications below qualify the curves shown on the following pages. Tolerances according to ISO 996 Annex A The curves refer to effective speed of asynchronous motors at 5 Hz Measurements were carried out with clean water at C of temperature and with a kinematic viscosity of ν = mm/s ( cst) In order to avoid the risk of overheating, the pumps should not be used at a flow rate below % of best efficiency point. Symbols explanation: Q = volume flow rate H = total head P = pump power input (shaft power) η = pump efficiency NPSH = net positive suction head required by the pump 4
PERFORMANCE CURVE 3 36/.9 (.9 kw ) Impeller diameter = 98.5 mm 35/.75 (.75 kw ) Impeller diameter = 98.5 mm 34/.65 (.65 kw ) Impeller diameter = 98.5 mm 33/.65 (.65 kw ) Impeller diameter = 98.5 mm V4 3 4 5 Q [m³/hr] 8 6 36/.9 H [m] 35/.75 34/.65 33/.65 NPSHR [m] NPSH 4 6 8 Q [l/min] P [kw].8.4 36/.9 35/.75 34/.65 33/.65. 6 8 Q [l/min] 6 [%] 6 8 Q [l/min] Impeller diameter : 98.5 mm Rotation speed ~ 85 min Test standard : ISO 996 Annex A
PERFORMANCE CURVE 5 56/.3 (.3 kw ) Impeller diameter = 97 mm 55/.3 (.3 kw ) Impeller diameter = 97 mm 54/.9 (.9 kw ) Impeller diameter = 97 mm V4 3 4 5 6 7 8 Q [m³/hr] 8 6 56/.3 55/.3 H [m] 54/.9 NPSHR [m] NPSH 4 5 Q [l/min] P. 56/.3 55/.3 [kw].8.4 54/.9. 5 Q [l/min] 6 [%] 5 Q [l/min] Impeller diameter : 97 mm Rotation speed ~ 85 min Test standard : ISO 996 Annex A
PERFORMANCE CURVE V4 5/. (. kw ) Impeller diameter =.5 mm 4/.5 (.5 kw ) Impeller diameter =.5 mm 4 6 8 4 6 Q [m³/hr] 8 6 5/. H [m] 4/.5 NPSHR [m] NPSH 4 Q [l/min] P. 5/. [kw]. 4/.5 Q [l/min] 8 [%] Q [l/min] Impeller diameter :.5 mm Rotation speed ~ 85 min Test standard : ISO 996 Annex A
PERFORMANCE CURVE 8 V4 83/. (. kw ) Impeller diameter = 6.7 mm 5 5 5 3 Q [m³/hr] 6 H [m] 83/. NPSHR [m] 4 NPSH 3. Q [l/min] P. 83/. [kw]. 8 Q [l/min] [%] Q [l/min] Impeller diameter : 6.7 mm Rotation speed ~ 875 min Test standard : ISO 996 Annex A 3
CONSTRUCTIONS 5 9 53 6 3 56 3 V4 69 7 6 68 8 33 9 9 34 9 33 6 3 63 33 9 6 4 3 4 77 75 3 (Only 83) 6 4 93 4 5 except models below No. Casing 3 4 6 7 3 4 5 Bracket Casing cover Shaft with rotor Impeller Mechanical seal Motor frame & stator Motor Cover Fan 6 Terminal board 8 9 PART NAME Fan cover Splash ring Bearing (Pump side) Bearing (Fan side) MATERIAL Aluminium Aluminium Polyamide NBR Wetted end. C ar/ C er/ EPD M Zinc plated steel 75 77 4 QTY No. 56 Box gasket [N = no. of stages] 5T/.M & 83T/.M Adjusting ring Steel C7 Tie rod Fe 4 zinc plated 4 3 Capacitor [N] 4 Plug (Drain & Fill) 6 O Ring EPDM 69 9 3 3 33 34 4 5 53 Washer Ring holder Shaft sleeve Ring Screw Foot PART NAME Capacitor box Cover box MATERIAL Aluminium Polypropylene Polypropylene NBR QTY No. # # 6 6 63 68 75 77 9 9 9 93 33 Intermediate Casing Inter. Casing (suction) Inter. Casing (discharge) Shaft Sleeve (intermediate) Impeller spacer Washer (plug) O Ring (plug) Cover box gasket Shaft washer Lip seal Lip seal Protector Screw Plate # refer to drg s above PART NAME Model 83 33 34, 54,4 35, 55,5 36, 56, * MATERIAL AISI 34 EPDM Z 4 6 8 refer to table above QTY [N] Z 8 4 * + only.3,.5 &.M Specifications subject to change without notice + 3
CONSTRUCTIONS MECHANICAL SEAL V4 MECHANICAL SEAL Manufacturer reference Version Material 3 4 5 6 7 Stationary Rotary Gasket Bellows Spring Frame Retainer seal ring seal ring ring BT Burgmann Standard Ceramic Carbon EPDM EPDM EN.4 (AISI 36) EN.4 (AISI 36) EN.4 (AISI 36) Approval for drinking water application WRAS Approved product DM74/4 3
DIMENSIONS AND W EIGHT V4 Units: mm unless otherwise specified B L Fig. D T 9 9 D Fig. D F W Ø R D 8 = = 57 B C 8 T H4 H4 Ø9 8 48 65 L G /8 G /8 G /8 9 9 G /8 3 3 Ø 9 F W 5 R 55 7 Pump Model Drg. D Dimensions (mm) D B C F H4 L R T W Weight 33T/.65M 36 7 3 84 5.5 Pg 88~97 9.9 kg 34T/.65M 35T/.75M Fig. 384 7 7 8 7 5 84 75.5 84 99.5 Pg Pg 88~97 88~97.6 kg.5 kg 36T/.9M 43 7 75 9 6 3.5 Mx.5 88~97 3.7 kg 54T/.9M 384 7 7 9 6 75.5 Mx.5 88~97. kg 55T/.3M Fig. ¼ 445 98 5 6 99.5 Mx.5 88~97 5. kg 56T/.3M 469 98 75 6 3.5 Mx.5 88~97 5. kg 4T/.5M 5T/.M Fig. Fig. ½ ¼ 446 54 48 78 6 3.5 84.5 Mx.5 Mx.5 9~.5 5.6 kg.3 kg 83T/.M Fig. ½ 49 4 3 5.5 Mx.5 4.5.6 kg
DIMENSIONS PACKING AND WEIGHT V4 PACKING AND WEIGHT Pump Type Weight Packing [mm] [kgf] X Y Z 33T/.65M.5 34T/.65M 9 8 43. 35T/.75M 3. 36T/.9M 58 56 4.5 54T/.9M 9 8 43 3 55T/.3M 58 56 5.8 56T/.3M 6 4T/.5M 6.4 5T/.M 58 56. 83T/.M.4 4
TECHNICAL DATA MOTOR, B EARING AND NOISE DATA V4 Pump Type Power Motor Capacitor Imput power Full load current Locked rotor current Bearing [A] [A] kw HP size pump side fan side mf Vc [kw] 3 V 33T/.65M.65.9 7 6 45.97 4.5 34T/.65M.65.9 7 6 45.97 4.5 63RSHC3 6RSH 35T/.75M.75. 7 5 45.4 5.4 36T/.9M.9. 7 3.5 45.8 5.7 54T/.9M.9. 7 63RSHC3 6RSH 3.5 45.8 5.7 55T/.3M.3.8 8 35 45.75 7.8 634RSHC3 63RSH 56T/.3M.3.8 8 35 45.75 7.8 4T/.5M.5. 8 634RSHC3 63RSH 45.95 8.7 5T/.M. 3. 9 635RSHC3 65RSHC3 5 45.9 3 83T/.M. 3. 9 635RSHC3 65RSHC3 5 45.9 3 3 V 6. 6. 6.5.7.7 4 4 43 6.4 6.4 NOISE DATA Pump Type Motor LpAdB(A)* Single phase Three phase kw HP size 33T/.65M 34T/.65M 35T/.75M 36T/.9M 54T/.9M 55T/.3M 56T/.3M 4T/.5M 5T/.M 83T/.M.65.9 7.75. 7.9..5. 8 64. 3. 9 68. 3. 9 68 *Mean value of several measures at m distance around the pump. Tollerance ±.5 db. 7.3.8 8 6 6 6 64 5