Part Number: SFR-313 Kit Contents Item # Quantity Reqd. Description 1 2 Light Housings 2 2 Fog Light bezels 3 1 Harness bag 4 1 User s card 5 1 Switch 6 1 Fuse jumper Hardware Bag Contents Item # Quantity Reqd. Description 1 1 Hood Wire Harness 2 1 Cabin Wire Harness 3 25 Wire ties 4 1 Black T-Tap 5 4 Phillip Head Screws 6 1 Relay 7 4 Speed Clips Recommended Tools Safety Tools Safety Glasses Protective tape Electrical Tape Installation Tools 10mm Wrench Phillips Screw Driver Pliers Panel Tool Removal 15/16 hole saw ¼ pilot drill bit Side Cutters Torque Wrench Special Chemicals 3M Silicon Sealant Mandatory Legend General Applicability All models Conflicts - DRL STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury CRITICAL PROCESS: Proceed with caution to ensure a quality installation. These points will be audited on a completed vehicle installation TOOLS & EQUIPMENT: This calls out the specific tools and equipment required for this process REVISION MARK: This mark highlights a change in installation with respect to previous issue.
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure quality installation. Preparation Remove negative battery cable Installation 1. From the front of the vehicle, run the positive spade terminal of the fog light harness through the area of fuse block. 2. Using the supplied fuse jumper wire, disconnect the rear window defog fuse. It is a 30A green fuse, right next to the red and green relays (picture 1) white factory clips to route the harness and place a wire tie at each factory clip. As the harness turns down at the headlight, install one wire tie on the fog light harness to the factory headlight harness (picture 2 & 2B) Picture 2 Picture 1 3. Connect the jumper fuse to the rear window defog fuse, then, connect the fuse and the red wire from fog light harness to the jumper. 4. Connect the ring terminal with the black wire from fog light harness to a ground location next to fuse block. 5. Run the fog light harness on the driver s side towards the firewall of the vehicle. Utilize the 2 Picture 2B 6. Locate the large vehicle harness grommet on the driver s side. If accessible, cut the auxiliary wiring access nipple off the grommet or cut a ¼ slit in the grommet and push the fog light wire through the firewall..
Note: Extra caution should be taken not to damage the connectors. Seal the grommet with silicone sealant. (Picture 3) Picture 5 9. Remove the driver s side panel. Disengage with panel tool and remove (picture 6) Picture 3 Vehicle Disassembly 7. Remove driver side door scuff plate. Disengage with panel tool and remove (picture 4) Picture 6 10. Remove the lower left panel on the driver side. Remove screw on left side. Then remove screw on the lower right side, next to the console box (picture 7, 7A and 7B) Picture 4 8. Remove driver side cowl side trim. Unscrew the cowl side retainer clip. Disengage two clips then remove the cowl plate (picture 5) Picture 7
Picture 7A Picture 8 Picture 8A Picture 7B 11. Put the lower panel on a protected bench. Remove the switch panel for the trunk release. On the back of the panel, locate the intersection of the two lines (picture 8). Using a ¼ drill bit, make a pilot hole at the intersection of the lines. Then drill a 15/16 hole with a hole saw. Debur hole if the switch needs more room 12. Install switch into dash (picture 9) Picture 9 13. From inside the cabin, locate the wire that was pushed through in step 6. It will be the grommet above the emergency brake pedal 14. Route the wire harness to reach the lowerleft side panel
15. At power mirror connector ED-2 connect the red wire from the switch harness to the whiteblack wire from pin 21. Use the supplied black t-tap. Connector ED-2 is located by main fuse block (pictures 10,11 and 12) Picture 13 17. Secure any excess wire to main wire harness (picture 14) Picture 10: Power mirror connector Picture 11: Power mirror connector Picture 14 18. Plug in the switch and reinstall all panels and connectors ENGINE COMPARTMENT Picture 12: Power mirror connector 16. Secure the black wire with the ring terminal to the ground location by the kick panel (picture 13) 19. On the driver side, route the fog light wire harness under car to reach left fog light area. 20. Remove lower splash shield by removing the pushpins and bolts at the bottom of the splash shield (picture 15 & 16)
Picture 15 Picture 17 23. Mount fog lights into fog light bezels. Note: Fog Lights are marked LH and RH. Use caution to select the proper side. 24. Connect both fog lights to wire harness 25. Secure excess wire with wire ties (pic. 18) Picture 16 21. Remove fog light cover plates 22. Run right side of fog light wire harness above the skid plate and through the channel (pictures 17) Picture 18 26. Align all the tabs of the Fog Light bezel before securing the bezel in place. Then snap both bezels into place 27. Reinstall splash shield. 28. Reconnect negative battery cable and torque to 53 in-lbs
Check System for Operation 1. Fog lights should only with the ignition key in ON position. Fog Light Aiming Traditional fog lights are usually mounted in the front bumper about 10-24 inches from the ground. There are two important issues to address when installing fog lights: the first is to minimize the amount of return glare into the drivers eyes, and the other is to minimize the glare into oncoming eyes. Both of these issues must be accomplished while putting as much light as possible on the road. These fog weather light aiming instructions are suggestions taken from common practice and the S.A.E. standard J583. Some modifications to these instructions may be necessary to minimize glare. Visual aim is made with the top of the beam 4 inches below the lamp center at 25 feet with the lamp facing straight forward (see picture 19) Picture 19
Checklist these points MUST be checked to ensure quality installation Check Accessory Functions Checks Look For: Fog Lights function.. All Panels snapped into place. Fog Lights Battery Terminal. Loose panels and switches Visually confirm lights are straight forward Re-torque battery terminals to 61 in-lb Vehicle Function checks Check Accessory Functions Checks Check functions all switch functions Fog Light function.. All Panels snapped into place. Battery Terminal Vehicle Function checks Check functions all switch functions
Look For:. Loose panels and switches Re-torque battery terminals to 53 in/lbs.