Draincoil corrugated drainage pipe is of a consistent high quality and comes in a broad range of sizes and grades. It is available slotted or unslotted, with or without filter sock. There is a full range of fittings to suit a wide variety of drainage projects. Features & Benefits Range of pipe diameters 50mm, 65mm, 80mm, 100mm and 160mm Lightweight, easily handling Flexible, able to bend around corners, moves with soil and does not crack Easy to install, ideal DIY product Minimal fittings required, ease of installation, moves with ground Pipe and fittings made in Australia Pipe made from consumer collected recycled polyethylene plastic Range of push-together fittings which lock to the corrugations of the pipe All fittings are barcoded for ease of check-out scanning P 13 11 69 sales@vinidex.com.au www.vinidex.com.au
Limitation of Liability This product catalogue has been compiled by Vinidex Pty Limited ( the Company ) to promote better understanding of the technical aspects of the Company s products to assist users in obtaining from them the best possible performance. The product catalogue is supplied subject to acknowledgement of the following conditions: 1 The product catalogue is protected by copyright and may not be copied or reproduced in any form or by any means in whole or in part without prior consent in writing by the Company. 2 Product specifications, usage data and advisory information may change from time to time with advances in research and field experience. The Company reserves the right to make such changes at any time without further notice. 3 Correct usage of the Company s products involves engineering judgements, which can not be properly made without full knowledge of all the conditions pertaining to each specific installation. The Company expressly disclaims all and any liability to any person whether supplied with this publication or not in respect of anything and all of the consequences of anything done or omitted to be done by any such person in reliance whether whole or part of the contents of this publication. 4 No offer to trade, nor any conditions of trading, are expressed or implied by the issue of content of this product catalogue. Nothing herein shall override the Company s Condition of Sale, which may be obtained from the Registered Office or any Sales Office of the Company. 5 This product catalogue is and shall remain the property of the Company, and shall be surrendered on demand to the Company. 6 Information supplied in this product catalogue does not override a job specification, where such conflict arises; consult the authority supervising the job. Copyright Vinidex Pty Limited.
Product Range - Pipe Corrugated Draincoil SN8 (CL400) SN Coil Length 24582 8 10m 50mm 65mm 80mm 24580 8 20m 24590 8 200m 24597 8 10m 24600 8 20m 24620 8 200m 24630 8 20m 24641* 8 100m 24707 8 10m 100mm 160mm 24700 8 20m 24710 8 100m 24745 8 40m Draincoil SN20 (CL1000) SN Coil Length 100mm 24724 20 100m Draincoil Unslotted SN8 (CL400) SN Coil Length 50mm 24585 8 20m 65mm 24603 8 20m 80mm 24635 8 20m 100mm 100mm 160mm 24820 8 20m 24840 8 100m 24713 8 100mm 24741 8 40m Diverter Hose 34mm hose fitted with 25mm cuff to suit most washing machine hoses or 25mm micro irrigation fittings. Large 34mm diameter increases flow, reduces back pressure on washing machine pump and prevents back up in laundry tub. 50mm diverter hose suitable for extra high flows. 34mm Product Code Coil Length 65573 10m 65574 20m 50mm 65575 20m * Products made to order, minimum order applies. 4 4
StormFlex Pipe SN12 StormFlex is a flexible alternative to rigid PVC stormwater pipe. It also replaces multiple fittings when joining downpipe to the groundpipe. StormFlex is white and stays stiff in direct sunlight. It is made from UV stabilised white polypropylene. StormFlex is also used for temporary stormwater diversion on construction sites. StormFlex Fittings displayed on page 13 are used for temporary stormwater connections on construction sites. Coil Length 100mm 24979 10m 24980 30m Draincoil SN8 (CL400) with Filtersock SN Coil Length 50mm Sock 24581 8 20m 65mm Sock 24608 8 20m 24625 8 200m 80mm Sock 24638 8 20m 100mm Sock 100mm RTA Sock 24703 8 20m 24712 8 100m 24698 8 100m 160mm RTA Sock 24746 8 40m Draincoil SN20 (CL1000) with Filtersock SN Coil Length 100mm RTA Sock 24725 20 100m 100mm PP Sock 24727 20 100m Filter Sock Filter sock is a geotextile sleeve manufactured from high tensile strength polyester yarn. It is fitted over Draincoil corrugated drainage pipe to prevent small particles of soil (fines) from entering the pipe and reducing the drainage capability. There are two grades to choose from. The heavier RTA grade conforms to the specifications of the New South Wales Road and Traffic Authority (RTA), hence its name. It has more continuously extruded fibres per yarn and can withstand higher loads of abrasion, strain and mechanical installation without tearing. Coil Length 65 RTA Filtersock Only 84656 100m 100 RTA Filtersock Only 84658 100m 5 5
Product Range - Draincoil Fittings Couplings 50mm 65620 10 120 65mm 65670 10 60 80mm 65015 10 100 100mm 65561 10 30 160mm 65014 1 12 Coupling SN20 (CL1000) 100mm 65030 10 30 Reducing Couplings 100mm to 50mm 65567 10 60 100mm to 65mm 65568 10 50 Tee 50mm 65571 10 60 65mm 65569 10 30 100mm 65600 5 15 Y Junctions 65mm 65572 10 30 100mm 65580 1 10 6 6
Branch Take-Off Tee 160mm to 50mm 65016 10 100 Crosses 65mm 65564 5 20 100mm 65610 1 14 End Caps 50mm 65565 10 240 65mm 65566 10 200 100mm 65570 10 100 End Grate 65mm 65013 10 150 Adaptors 100mm Draincoil to 90mm PVC Stormwater 100mm Draincoil to 100mm PVC DWV 65563 65560 10 40 10 30 7 7
Product Range - StormFlex Fittings PVC Fittings 100mm Coupling 65012 1 20 100mm x 90mm Adaptor 65011 10 50 StormFlex Fittings Applications StormFlex to StormFlex 90mm PVC to StormFlex 100mm DWV to StormFlex Greywater Fittings Greywater Diverter Valve 40mm PVC Outlet 65577 5 30 50mm PVC Outlet 65576 5 30 Greywater Diverter Hose Connector Cuffs 34 x 34mm Connector Cuff 65017 20 240 34x 25mm Hose Adaptor Cuff 65018 10 300 Greywater Hose Adaptor 50mm DWV to 25mm LD 65562 20 240 Rainwater Fittings Rainwater Diverter Use to divert rainwater to pools, gardens and water tanks. Can be converted from left to right-hand. Suits 90mm diameter stormwater pipe. 90mm 65578 5 10 8 8 *Please contact Vinidex for ordering information.
Rainwater Fittings (cont.) Adaptors A full range of adaptors are available for connecting Rainwater Diverters to diverter hose. There are two styles of downpipe adaptors to ensure leak-proof connections when converting from round to rectangular or rectangular to round. 50mm DWV Socket to 50mm Diverter Hose 65019 10 200 90mm Stormwater Socket to 50mm DWV 65024 10 70 100mm x 50mm Rectangular Downpipe to 90mm Stormwater Adaptor 65025 10 50 90mm Stormwater to 100mm x 50mm Rectangular Downpipe Adaptor 65026 10 60 Rainwater Fittings Installation Options Installation Options: The 90mm Rainwater Diverter is very versatile and can be adapted for use in a wide variety of applications, some of which are depicted below. 1. Use with 50mm Diverter Hose 2. Adapting to Rectangular downpipe 3. Diverting to 90mm Stormwater pipe Note: The 90mm Rainwater Diverter is not a valve. Some leakage between outlets will occur. Right-Hand and Left-Hand Installation: The 90mm Rainwater Diverter can be used for both left-hand and right-hand installations. Always check that the diverter valve has has been set to the correct orientation after installation. The T arrow on the handle should always rotate between the side and bottom outlets. If this is not the case then unscrew the front cover, remove the handle and reinsert it in the correct orienta - tion. In Left-Hand Install Right-Hand Install Unscrew Front Drain Reinsert valve gate at 45º angle If the handle is installed upside down, i.e. with the T arrow pointing upwards, then the inlet will be blocked and the diverter will not function. P 13 11 69 sales@vinidex.com.au www.vinidex.com.au VIN028-20150228