ACCESSORIES 312. DIMMERS 315. SENSORS 318. CONNECTORS 320. SADDLES 321. SURFACE SOCKETS 322. BATTEN FIXTURE 322. POWER BOARDS 323. EXTENSION LEAD 324. FLEX & PLUGS 325. LAMP HOLDERS 326. STARTERS 311
Push Button LED Trailing Dimmer VELA PRODUCT FEATURES Soft start Overload protection & short circuit protection Easy to mount in most Australian plates Suitable for dimming dimmable LED globes, incandescent globes, high voltage halogen globes, electronic transformers with low voltage halogen globes Long press dimming button to dim Short press dimming button to on/off Comes with 2 face caps round & square edged to suit most Australian plates IP rating: IP20 WARRANTY 3 year replacement warranty round edged face square edged face also available PROGRAMMING Minmum brightness setting (1) Remove the top cap (2) Long press programming button until LED flashes slowly (3) Long press dimming button to set level (4) Double press dimming button to exit programming mode Maximum brightness settting (1) Remove the top cap (2) Long press programming button until LED flashes, short press programming button, until LED starts to flash fast (3) Long press dimming button to set level (4) Double press dimming button to exit program mode TECHNICAL DATA Rated voltage & frequency Rated Power Hi-Pot Environmental Requirement Altitude RoHS Reach Life time of rotary button 220-240V AC 50Hz 5-350VA Applying 3KVrms voltage between the surface of the button of the unit against its opening ends of two fly wires which are electrically connected together, the unit will not have trigger current higher than 1mA during the 1 minute test duration Ambient temperature: 0 to 40 0 C Operating humidity: 10% to 95% RH, no condensing Storage temperature: 0 to 60 0 C Storage humidity: 10% to 95% RH, no condensing This product can only be operated at less than 2000 meters above to sea level The European Directive 2011/65/EU RoHS Compliance required The European Union directive 1907/2006/EC Compliance required Min. 20,000 cycles Wiring Practices Comply with AS/NZS 3133 Logo of certification CE, RCM Size 23.5mm x 23.5mm x 44.3mm (W x L x H) 312
LED Dimmer: Configured to excel with CLA GAL & NOVA range of LED Downlights LYNX Although optimised for LED lighting loads, this trailing edge dimmer also provides excellent compatibity with other common globe types such as incandescent globes, 12V halogen globes/ transformers and CFL's Suitable for 2-way switching (with cabling) Maximum LED product=90w PRODUCT FEATURES Fits Australian wall switch plate apertures (for example, the Sylvania Trader Cougar ranges, plus HPM and Clipsal ranges) Separately switched 2-wire design - no neutral wire connection required for wallplate retrofit installation Inbuilt over-current and over temperature protection Incorporates a thermal fuse Rotary control with mechanical adjustment for minium brightness level Protected against damage from connection to incompatible inductive load type (i.e. motor loads), via conduction angle wind-back Complies with all relevant Australian standards "Soft-start" helps prolong lamp and driver life WARRANTY 2 year replacement warranty DESCRIPTION LOAD LENGTH WIDTH KNOB WIDTH KNOB DIAM LYNX LED TRAILING EDGE DIMMER 5-400VA 55 22 13 Ø20 1/200 313
Leading Edge Economy Dimmer - L400E Modular dimmer mechanism Suitable for low voltage lighting with iron-core transformers Suitable for incandescent & main voltage halogen globes Australian pattern plate most common brands Trailing Edge Professional Dimmer - T400P Modular dimmer mechanism with superior digital technology Suitable for low voltage lighting with electronic transformers Suitable for fluorescent & main voltage halogen globes Australian pattern plate most common brands Leading Edge Professional Dimmer - L400P Modular dimmer mechanism with superior digital technology Suitable for low voltage lighting with electronic transformers Suitable for main voltage halogen globes Australian pattern plate most common brands No humming Trailing Edge Dimmer for CFL - T400PCFL Modular dimmer mechanism with superior digital technology Suitable for dimmable fluorescent globes Load: 13Wx15W to 10Wx20W Suitable for low voltage lighting with electronic transformers Suitable for main voltage halogen and incandescent globes Australian pattern plate most common brands No humming Multi-gang application, max, load of the dimmer needs to be rated Recommended for CLA dimmable 15W & 20W globes DESCRIPTION LOAD TA L400E 400VA LEADING EDGE ECONOMY DIMMER 50-400W 40 0 C 10/100 T400P 400VA TRAILING EDGE PROFESSIONAL DIMMER 20-400W 40 0 C 10/100 L400P 400VA LEADING EDGE PROFESSIONAL DIMMER 20-400W 40 0 C 10/100 T400PCFL 400VA TRAILING EDGE DIMMER FOR CFL 200W 40 0 C 10/100 314
INFRARED MOTION SENSORS SENS001 & SENS002 Surface mounted 3 wired Detection range: 180 0 Detection distance: 12m max (<24 0 C) Detection motion speed: 0.6-1.5m/s Input voltage: 220-240V AC 50/60Hz Rated load: 1200W Time delay: min.10sec+3sec; max.15min+2min Ambient light: <3-2000lux (adjustable) Installation height: 1.8-2.5m Suitable for use with LED IP rating: IP65 5 year replacement warranty SENS001 SENS002 SENS003 Surface mounted 3 wired Detection range: 360 0 Detection distance: 6m max (<24 0 C) Detection motion speed: 0.6-1.5m/s Input voltage: 220-240V AC 50/60Hz Rated load: 1200W Time delay: min.10sec+3sec; max.15min+2min Ambient light: <3-2000lux (adjustable) Installation height: 2.2-4m Suitable for use with LED IP rating: IP20 5 year replacement warranty 315
SENS004 Surface mounted 3 wired Detection range: 360 0 Detection distance: 6m max (<24 0 C) Detection motion speed: 0.6-1.5m/s Input voltage: 220-240V AC 50/60Hz Rated load: 2000W Time delay: min.10sec+3sec; max.15min+2min Ambient light: <3-2000lux (adjustable) Installation height: 2.2-4m Suitable for use with LED IP rating: IP20 5 year replacement warranty SENS005 Surface mounted 3 wired Detection range: 360 0 Detection distance: 20m max (<24 0 C) Detection motion speed: 0.6-1.5m/s Input voltage: 220-240V AC 50/60Hz Rated load: 2000W Time delay: min.10sec+3sec; max.30min+2min Ambient light: <3-2000lux (adjustable) Installation height: 2.2-6m Suitable for use with LED IP rating: IP20 5 year replacement warranty DECTECTION RANGE RATED LOAD(W) DETECTION DISTANCE(m) INSTALLATION HEIGHT(m) IP RATING SENS001 180 0 1200 Max.12 (<24 0 ) 1.8-2.5 IP65 - SENS002 180 0 1200 Max.12 (<24 0 ) 1.8-2.5 IP65 - SENS003 360 0 1200 Max.6 (<24 0 ) 2.2-4 IP20 - SENS004 360 0 2000 Max.6 (<24 0 ) 2.2-4 IP20 - SENS005 360 0 2000 Max.20 (<24 0 ) 2.2-6 IP20-316
LED SENSOR OYSTER(OYS3AS&OYS4AS) ACCESSORIES MICROWAVE SENSOR SENS006 Input voltage: 240V 50/60Hz Suitable for Capacitive & Resistive loads Load: 400W(Capacitive Load) & 800W(Resistive Load) 4 different hold time modes Good detection range Easy set-up switch Instructions incl. in box For use inline before control gear IP rating: IP20 Ambient temp: -20 to 600C 3 year replacement warranty Can be used with CLA OYS dimmable series Can only be installed in a fitting with glass cover, PC cover or PMMA cover on the condition that the thickness of the cover is less than 1cm. DETECTION RANGE DETECTION ANGLE DETECTION AREA HOLD TIME SENS006 (ø x H) 10mx6m 300-500 10%/50% 75%/100% 5sec/9sec 5min/15min STANDBY POWER <0.5W MICROWAVE FREQUENCY MOUNTING HEIGHT(m) 5.8GHZ ± 75MHZ 6 1/1 317
TM TM ACCESSORIES Waterproof Connectors WATERPROOF CONN SERIES PRODUCT FEATURES Copper cabling max-4mm braidedw Screw Terminal Material: Brass with Ni Plated High Temperature rating: -40 C to +105 C Silicon Gel gasket Nylon glass fiber reinforced (PA66 + GF V0) IP rating: IP68 If using flat sheathed cable, connector ends need to be sealed with waterproof compound. CONN001 WARRANTY 12 month replacement warranty 4 3 2 1 D 24.8 D 24.8±0.5 C 76.6±3 66.7 C CONN002 Material: 97.2 Connector Body:Nylon(PA66)+GF V0 Contact: Brass with Ni Plated, Screw Terminal B Gasket: Silicon Gel Specification: Current Rating: 25A 3 CURRENT RATING VOLTAGE RATING Current Rating: 380V/AC Contact Resistance:<5mohm CONN001 Insulation DOUBLE WATERPROOF Resistance: CONNECTOR 100Mohm at 500V 25A 380V/AC Breakdown Voltage: 1500V/1Minute 5mA Temperature Rating: -40 -+105 CONN002 A Waterproof TRIPLE WATERPOOF rating: IP68 CONNECTOR 25A 380V/AC Cable Diameter: 6.5mm-10.0mm Certificates: SAA 4 2 CONTACT RESISTANCE CLA LIGHTING BREAKDOWN VOLTAGE 100Mohm 1500V/1Min at 500VCONN002 5mA PART NAME MODEL No. DWG No. 100Mohm RELEASE DATE 2016.03.09 SCALE at 500V1:1 SIZE A4 VER V1.0 CHK'D 1500V/1Min APP'D 5mA 1 DRAW THIRD ANGLE PROJECTION B CIRCULAR CABLE DIAM 6.5-10 1/1 A 6.5-10 1/1 318
Cable Connectors INDOOR CONN SERIES PRODUCT FEATURES Double or single cable connectors Construction material: transparent PC Screw material: copper Wiring hole: 6mm Max.current: 32A IP rating: IP20 WARRANTY 3 year replacement warranty CONN003 CONN003 CONN004 CONN004 MAX. CURRENT IP RATING WIRING HOLE LENGTH WIDTH HEIGHT CONN003 SINGLE CONNECTOR CABLE 6MM 2 32A IP20 1x6mm 2 19.2 12 22.6 1/2500 CONN004 DOUBLE CONNECTOR CABLE 6MM 2 32A IP20 2x6mm 2 27 12 23.5 1/1250 319
Stainless Steel / Alloy Steel Saddles SADDLE SERIES PRODUCT FEATURES SADDLE001-004 material: stainless steel 304 SADDLE005-008 material: alloy steel SADDLE001,2 SADDLE003,4 SADDLE005,6 SADDLE007,8 SADDLE001 SADDLE002 SADDLE003 SADDLE004 SADDLE005 SADDLE006 SADDLE007 SADDLE008 320
SADDLE001 SADDLE002 SADDLE003 SADDLE004 SADDLE005 SADDLE006 SADDLE007 SADDLE008 STAINLESS STEEL 20MM HALF SADDLE 5MM HOLE STAINLESS STEEL 25MM HALF SADDLE 5MM HOLE STAINLESS STEEL 20MM FULL SADDLE 5MM HOLE STAINLESS STEEL 25MM FULL SADDLE 5MM HOLE ALLOY STEEL 20MM HALF SADDLE 5MM HOLE ALLOY STEEL 25MM HALF SADDLE 5MM HOLE ALLOY STEEL 20MM FULL SADDLE 5MM HOLE ALLOY STEEL 25MM FULL SADDLE 5MM HOLE 3-PIN SURFACE SOCKET SOCK1 240V 50Hz Material: PC 2 screws mount 2 opening for input wire (one on each side) 10Amp current rating Product is earthed Recommended cable 1.0mm to 2.5mm Box of 10 (strictly box order only) IP rating: IP20 SOCK1 QUICK CONNECT SURFACE SOCKET SOCK2 240V 50Hz Material: PC 10Amp current rating Product is earthed Recommended cable 1.0mm to 2.5mm The cable must be stripped back first before placing cable in the socket Box of 10 (strictly box order only) SOCK2 HEIGHT WIDTH/DIAM SOCK1 REAR CONNECTING SINGLE 3-PIN SURFACE SOCKET 55 68 10/200 SOCK2 QUICK CONNECTING SURFACE SOCKET - - 10/200 321
BATTEN FIXTURE (B22 BASE) BATFIX 240V 50Hz Material: PC 10Amp current rating Product is earthed Box of 10 (stickly box order only) BATFIX HEIGHT WIDTH/DIAM BATFIX BATTEN FIXTURE FOR BC BASE GLOBES - - 10/100 POWER BOARDS Available in 4 power outlets and 6 outlets 1m white AC cord with insulated pins Overload protection with test button Low profile design Ideal for home or office use CLA4PB CLA6PB CLA4PB 4-WAY GPO POWER BOARD WITH 1000MM FLEX & PLUG 1/12 CLA6PB 6-WAY GPO POWER BOARD WITH 1000MM FLEX & PLUG 1/12 322
PLUGS & EXTENSION LEADS PRODUCT FEATURES Low profile design Ideal for domestic use like homes and offices WARRANTY PLUG001 PLUG002 PLUG001 REWIRABLE 3 PIN PLUG TOP 3A CLEAR (MALE) 1/200 PLUG002 REWIRABLE 3 PIN PLUG TOP 3A CLEAR (FEMALE) 1/200 LEADW001 EXTENSION LEAD WHITE 10A 2M 1/50 LEADW002 EXTENSION LEAD WHITE 10A 3M 1/50 LEADW003 EXTENSION LEAD WHITE 10A 5M 1/30 LEADW004 EXTENSION LEAD WHITE 10A 7M 1/25 LEADW005 EXTENSION LEAD WHITE 10A 10M 1/20 LEADB001 PIGGY BACK EXTENSION BLACK 15A FLEX / 10A PLUG & SOCKET 1M 1/60 LEADB002 PIGGY BACK EXTENSION BLACK 15A FLEX / 10A PLUG & SOCKET 2M 1/50 LEADB003 PIGGY BACK EXTENSION BLACK 15A FLEX / 10A PLUG & SOCKET 3M 1/30 LEADB004 PIGGY BACK EXTENSION BLACK 15A FLEX / 10A PLUG & SOCKET 5M 1/25 LEADB005 PIGGY BACK EXTENSION BLACK 15A FLEX / 10A PLUG & SOCKET 10M 1/10 LEADB006 PIGGY BACK EXTENSION BLACK 15A FLEX / 10A PLUG & SOCKET 15M 1/8 LEADB007 PIGGY BACK EXTENSION BLACK 15A FLEX / 10A PLUG & SOCKET 20M 1/8 LEADB008 PIGGY BACK EXTENSION BLACK 15A FLEX / 10A PLUG & SOCKET 25M 1/6 LEADB009 PIGGY BACK EXTENSION BLACK 15A FLEX / 10A PLUG & SOCKET 30M 1/6 LEADW001-005 LEADB001-009 323
FLEX & PLUGS with INLINE SWITCH From plug to switch: 1.8m From switch to connecting: 106cm FP2WSB FP2WSW FP2WSB POWER CORD INLINE SWITCH BLACK 2.9M LEAD 1/50 FP2WSW POWER CORD INLINE SWITCH WHITE 2.9M LEAD 1/50 FLEX & PLUGS FP2M2W INSULATED 2 PIN CORE WIRE LEAD 2M 240V 1/100 FP2M3W INSULATED 3 PIN CORE WIRE LEAD 2M 240V 1/100 FP1.2M2W INSULATED 2 PIN CORE WIRE LEAD 1.2M 240V 1/100 324
12V LAMP HOLDERS LH1.5M 12V 1.5M CERAMIC LAMP HOLDER 10/100 LH0.4M 12V 40CM CERAMIC LAMP HOLDER WITH SHEATH 10/100 LH0.2M 12V 20CM CERAMIC LAMP HOLDER 10/100 GU10 LAMP HOLDERS CLAGU10LH CLAGU10LHFP CLAZGU10LH CLAGU10LH GU10 POST & LAMP HOLDER 90MM WITH CORD 1/100 CLAGU10LHFP GU10 POST & LAMP HOLDER WITH FP2M3W FLEX & PLUG 1/100 CLAZGU10LH GU10 POST & LAMP HOLDER SUIT 'Z' FRAME 110MM WHITE CORD 1/100 325
STARTERS CLAFSU-STARTER Starter FL S10 4W to 80W Suitable for T8 circular and straight tubes and 2x36W fittings CLAFSV2 Starter FL S2 2x18 / 20W Only suitable for 18W fitting and twin lamps LEDSTARTER CLAFSU-STARTER Starter (fuse) for LED fittings Suitable for use with most LED fittings (short circuits) LEDSTARTER DIAM HEIGHT CLAFSU-STARTER STARTER FL S10 40W TO 80W Ø20 36 25/1000 CLAFSV2 STARTER FL S2 2X18 / 20W Ø20 36 25/1000 LEDSTARTER LED STARTER (FUSE) FOR LED FITTINGS 1/1 326