AUGUST, 0 000T TERRACE DOOR FEATURES Features Performance class and grade: Single: AW-PG90-ATD Pairs: AW-PG45/65-ATD Inswing or outswing -/4" deep door rails and stiles Mitered door and frame corners Heavy duty internal corner clips " x 4" door frame 0.5 nominal wall thickness, door and frame Three way adjustable butt hinges Polyamide thermal break Double row of weather seals Stainless steel multipoint latch lock / deadbolt with swinghooks and shootbolts as required Solid brass lever handle selection in multiple finishes Removable tubular interlocking glazing beads Accommodates /4", 5/6", /8", /", 9/6", 5/8", /4", /6", " and -/6" infills Dry glazed method Factory glazed shipped with door hung in frame Kawneer standard finishes Two color option Integral astragal on pairs Optional Features Concealed stainless steel doorstop LCN 60 surface applied closer Product Applications The Series 000T Terrace Door is a high performance French door for use in condominiums, lofts, hotels and apartments The Series 000T Terrace Door Frame is intended to be installed in "punched" openings or as a liner frame within other Kawneer framing or curtain wall systems When sidelites and/or transoms are required the 000T door frame is installed as a liner frame within other Kawneer framing or curtain wall systems For specific product applications, Consult your Kawneer representative.
000T TERRACE DOOR AUGUST, 0 BLANK PAGE
AUGUST, 0 000T TERRACE DOOR INDEX OUTSWING DOOR DETAILS... 5 INSWING DOOR DETAILS... 6 SIDELITES AND TRANSOM... 7 STANDARD GLAZING OPTIONS... 8 HARDWARE...9, 0 STRUCTURAL LIMITATIONS... THERMAL CHARTS... -5 LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. The following metric (SI) units are found in these details: m meter cm centimeter mm millimeter s second Pa pascal MPa megapascal Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement.
4 000T TERRACE DOOR AUGUST, 0 BLANK PAGE
AUGUST, 0 000T TERRACE DOOR OUTSWING DOOR DETAILS 5 SCALE " = ' 0" Single Door Maximun Frame Size = 48" x 96" (9. x 48.4) Minimum Frame Size = 0" x 7" (76 x 854.) HEAD FRAME HEIGHT /8" (9.5) 7/" (.5) 5-/8" (0.) 4-/" (.9) /6" 4" (0.6) 4 " (5.4) -5/" (45.) opp. OUTSWING DOORS & FRAME -5/" (45.) " (5.4) 5 Pair of Doors Maximun Frame Size = 96" x 96" (48.4 x 48.4) Minimum Frame Size = 60" x 8" (54 x 057.4) -5/" (45.) " (5.4) FRAME HEIGHT 5-/8" (0.) 4-/" (.9) /8" (9.5) 7/" (.5) /6" " (5.4) /6" 7/" (.5) /8" (9.5) -5/" (45.) 4-/" (.9) FRAME WIDTH SILL 4 PIVOT JAMB 4-/" (.9) FRAME WIDTH LOCK JAMB AT DEADBOLT/LATCHLOCK /6" 7/" (.5) /8" (9.5) 4-/" (.9) /6" 4-/" (.9) 9" (8.6) 5 MEETING STILE
6 000T TERRACE DOOR AUGUST, 0 INSWING DOOR DETAILS SCALE " = ' 0" Single Door Maximun Frame Size = 48" x 96" (9. x 48.4) Minimum Frame Size = 0" x 7" (76 x 854.) HEAD /8" (9.5) FRAME HEIGHT 5-/8" (0.) " (5.4) -/" (84.9) 4" (0.6) 4 /6" -5/" (96.0) 7/" (.5) 7/" (.5) /6" INSWING DOORS & FRAME 4-/" (.9) 5 opp. Pair of Doors Maximun Frame Size = 96" x 96" (48.4 x 48.4) Minimum Frame Size = 60" x 8" (54 x 057.4) -5/" (.9) 7/" (.5) /6" /8" (9.5) SILL FRAME HEIGHT 5-/8" (0.) -/" (84.9) " (5.4) 4-/" (.9) /6" 7/" (.5) /8" (9.5) 4-/" (.9) " (5.4) 9" (8.6) /6" -/" (84.9) 5-/8" (0.) FRAME WIDTH PIVOT JAMB 4-/" (.9) -/" (84.9) 5-/8" (0.) FRAME WIDTH " (5.4) 4 LOCK JAMB AT DEADBOLT/LATCHLOCK /8" (9.5) 5 MEETING STILE
AUGUST, 0 SCALE " = ' 0" 000T TERRACE DOOR SIDELITES AND TRANSOM 7 4 OUTSWING DOORS & FRAME TRIFAB 45T FRAME SHOWN 4 TRANSOM HEAD TRANSOM BAR SIDELITE JAMB 4 DOOR JAMB
8 000T TERRACE DOOR AUGUST, 0 STANDARD GLAZING OPTIONS SCALE " = ' 0" 5/8" (5.9) GLASS BITE /4" INFILL OUTSWING DOOR /4" (6.4) WEDGE GASKET 5/8" (5.9) /4" (6.4) GLASS BITE /4" INFILL INSWING DOOR WEDGE GASKET " (5.4) " (5.4) WEDGE WEDGE GASKET GASKET 5/8" (5.9) GLASS BITE " INFILL OUTSWING DOOR 5/8" (5.9) GLASS BITE " INFILL INSWING DOOR
AUGUST, 0 TRIM SETS 000T TERRACE DOOR HARDWARE 9 LATCHLOCK/DEADBOLT GEARBOX Contemporary style solid brass lever handle and escutheon plate. Available in three finishes Polished Brass, Brushed Chrome and Rustic Umber. Includes keyed cylinder and thumbturn. Stainless steel gearbox provides both a latchlock for normal use and deadbolt for additional security. Lock strike plates are stainless steel and adjustable. Each includes an injection molded plastic dust box. SWINGHOOK SHOOT BOLT AND SLEEVE Swinghooks provide additional locking points along the vertical edge of the door leaf. Lockstrikes are stainless steel and adjustable. Each includes an injection molded plastic dust box. Top and bottom stainless steel shoot bolts secure the inactive leaf of pairs to the transom bar and threshold.
0 000T TERRACE DOOR AUGUST, 0 HARDWARE CONSTRUCTION HANDLE AND BACK PLATE ADJUSTABLE BUTT HINGE Trim sets are shipped loose to avoid damage during construction. The construction handle and construction plate allow temporary operation of the locking hardware. Aluminum -way adjustable hinges improve alignment between door leaf and frame. Hinges adjust in and out, up and down and left to right without removing the door leaf. Available in clear and dark bronze anodized finishes or painted to match door leaf. SURFACE APPLIED CLOSER DOOR STOP Door and frame will accommodate LCN 60 surface mounted closer and drop plate. Note: Closer is mounted on exterior side of frame with inswing door. Stainless steel door stop assemblies are concealed in the top rail of the door leaf.
AUGUST, 0 WINAD LIMITATIONS 000T TERRACE DOOR STRUCTURAL LIMITATIONS Charted windload curves are based on allowable stress for aluminum of 5,5 PSI and a L/75 deflection ratio and, in all cases represent the limiting values. Dimensional limits at the stated windloads are for door frame members anchored at the ends. GLASS HEIGHT IN FEET SMALL ASTRAGAL GLASS CENTERS IN METERS 0 9 8 7 6 5 4 0.5.0.5.0 A B D C.5 E.0.5.0 0.5 GLASS HEIGHT IN METERS A = 0 PSF (960) B = 0 PSF (440) C = 40 PSF (90) D = 50 PSF (400) E = 60 PSF (880) 590 5909 5909 0 0 4 5 GLASS CENTERS IN FEET MEDIUM ASTRAGAL GLASS HEIGHT IN FEET GLASS CENTERS IN METERS 0 9 8 7 6 5 4 0 0 0.5.0 4 5.5.0 A B.5 D C E.0.5.0 0.5 GLASS HEIGHT IN METERS 59 5909 5909 GLASS CENTERS IN FEET
000T TERRACE DOOR AUGUST, 0 THERMAL CHARTS Project Specific U-Factor Example Calculation 0.5" (765.) () 7'-" (84.4) '-4" (06.0) (F.W.) Example Glass U-Factor = 0.8 Btu/hr ft F 75.75" (94.) Total Daylight Opening = 0.5" x 75.75" = 5.85 ft Total Projected Area = '-4" x 7'-" =.9 ft Percent of Glass (F.H.) = (Total Daylight Opening Total Projected Area)00 = (5.85.9)00 = 66% () Note: 000T Terrace Door outswing shown for example. System U-factor vs Percent of Glass Area 0.90 0.85 (5.00) COG U-factor 0.48 (.7) 0.46 (.6) 0.44 (.50) 0.4 (.9) 0.40 (.7) 0.8 (.6) 0.6 (.05) 0.4 (.9) 0. (.8) 0.0 (.7) 0.8 (.59) 0.6 (.48) 0.4 (.7) 0. (.5) 0.0 (.4) EXAMPLE NOT FOR DESIGN 0.80 0.75 0.70 0.65 0.60 0.55 0.50 0.49 0.45 0.40 0.5 0.0 0.5 Btu hr ft F System U-factor (4.50) (4.00) (.50) (.00) (.50) (.00) (.50) W m C System U-factor 0.0 85 80 75 70 65 60 Percent of Glass Area Based on 66% glass and center of glass (COG) U-factor of 0.8 System U-factor is equal to 0.49 Btu/hr ft F 66%
AUGUST, 0 000T TERRACE DOOR - SINGLE LEAF 000T TERRACE DOOR THERMAL CHARTS Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 COG U-factor System U-factor vs Percent of Glass Area Btu hr ft F System U-factor Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
4 000T TERRACE DOOR AUGUST, 0 THERMAL CHARTS 000T TERRACE DOOR - SINGLE LEAF COG SHGC System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area System SHGC Vision Area / Total Area (%) COG VT System Visible Transmittance (VT) vs Percent of Vision Area Vision Area / Total Area (%) System VT
AUGUST, 0 000T TERRACE DOOR THERMAL PERFORMANCE MATRIX (NFRC SIZE) 000T TERRACE DOOR - SINGLE LEAF Thermal Transmittance (BTU/hr ft F) 5 Glass U-Factor Overall U-Factor 4 0.48 0.58 0.46 0.56 0.44 0.55 0.4 0.54 0.40 0.5 0.8 0.5 0.6 0.50 0.4 0.49 0. 0.48 0.0 0.47 0.8 0.46 0.6 0.44 0.4 0.4 0. 0.4 0.0 0.4 SHGC Matrix Visible Transmittance Glass SHGC Overall SHGC 4 Glass VT Overall VT 4 0.75 0.70 0.65 0.60 0.55 0.50 0.45 0.40 0.5 0.0 0.5 0.0 0.5 0.0 0.05 0.5 0.47 0.44 0.4 0.8 0.4 0. 0.8 0.5 0. 0.8 0.5 0. 0.08 0.05 0.75 0.70 0.65 0.60 0.55 0.50 0.45 0.40 0.5 0.0 0.5 0.0 0.5 0.0 0.05 NOTE: For glass values that are not listed, linear interpolation is permitted.. U-Factors are determined in accordance with NFRC 00.. SHGC and VT values are determined in accordance with NFRC 00.. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 000mm wide by 000mm high (9-/8" x 78-/4"). 0.49 0.46 0.4 0.9 0.6 0. 0.9 0.6 0. 0.0 0.6 0. 0.0 0.07 0.0
6 000T TERRACE DOOR AUGUST, 0 BLANK PAGE