3 4/16 82mm DIRECT 3 9/16 90mm 3 6/16 85mm L3ID-TRI-SYS DR OP Article # Distribution Diffuser Length Voltage Linear Electrical Mounting Brackets Lighting Control Product Distribution Diffuser Length Voltage Inserts Electrical Options L3ID-TRI-SYS DR -Direct OP -Opal State desired length 120V Linear LED Fluorescent Idaho Trimless 277V LED DP - Phase Dimming Non-Dimming L306 - DV - 0-10V Dimming SO - Standard Output 347V L406 - DL - Lutron Hi-Lume A series HO - High Output (Optional) L356-3500K (Upon request) Dimming EM - Emergency (Supplied by others) DIM1-0-10V Fluorescent Other: Please specify DIME - Lutron Eco System(10%) S1 -T5SO1lamp DIME3 - Lutron Eco System 3 Wire (10%) H1 -T5HO1lamp DIM3D - Lutron Hi-Lume 3D (1%) DIM3D3 -LutronHi-Lume3Wire(1%) DIMEH - Lutron Eco System H series (1%) EM - Emergency Other: Please Specify Mounting Brackets Ceiling Thickness (Drywall) 10-10mm (3/8") 12-12.5mm (1/2") 15-15mm (5/8") Wired Lighting Control DOS - Daylight & Occupancy Sensor For unique customized profiles please include a layout drawing or description below; * Include detailed information such as distance between linear lamps, spots and aluminum caps. ** Zaneen will supply submittal drawing for approval once a Purchase Order is received. Profile Layout Suggestions Available for International specifications by adding 'INT' at the end of the existing Model #. International spec sheets are available upon request. For assistance to write your custom specification, email your inquiry to: specification@zaneen.com. You will receive a response within 1-2 business days. Page 1 of 8
Type Surface (Non-IC Type) Ceiling or Wall (uplight or downlight) mounted Rated for Dry or Damp locations (IP20) Approval Certified by C.S.A. for North American Standards Emission Direct or Asymmetric. Aluminum caps offered to customize the location of the spot light. Efficiency Acrylic diffuser (snap-in) lens 43% Micro prismatic (snap-in) lens 53% PROFILE INSERTS Linear LED LED LED LED 3500K (Upon request) (LM 79-80) LED inserts are offered in lengths stated in page 4. Zaneen will finalize the actual profile length after calculating the inserts required. * Please contact Zaneen for other color temperature options. Measurements w. 82mm x ht. 90mm (3 1/4" x ht. 3 9/16") Housing Anodized extruded aluminum profile up to 8-0 long. Profiles are joined with a coupler to ensure uniform appearance and easy installation. Extruded aluminum offers high reflective surface and excellent heat dissipation. Corners 100% homogeneous appearance. 90 degree and custom angles (45-180 degree) are available. Corners are created with mitered cut in lens and aluminum. End Cap has no visible screws. Finishes Standard; Natural anodized aluminum Optional; 24 colors offered using premium powder coated finish. Profile and end caps can be specified in different finishes. Wall Bracket If required, aluminum wall brackets are located approximately every 4ft-5ft. Fasteners and wall anchors are supplied by others. Fluorescent Available Configurations 1 lamp overlap T5 SO: 21W, 28W, 35W T5 HO: 39W, 54W 2 lamp overlap T5 SO: 28W T5 HO: 54W Emergency T5 SO: 21W, 28W, 35W T5 HO: 39W, 54W Lamp Combination For specific lamp combinations or configurations, please specify the overall length and attach a sketch or drawing of the intended configuration. Zaneen will supply submittal drawings for approval once a Purchase Order is received. Mounting Holes Keyholes are drilled at the factory. Mounting hardware are supplied and installed by others. When using wall fastening spacer or key hole milling, fixture must be specified as up light or down light. Page 2 of 8
ELECTRICAL LIGHTING CONTROL Luminaires are pre-wired with a factory installed branch circuit wiring and quick-release connectors. Through wiring is used to connect the luminaires. BX Cable is connected directly into the fixture. Junction cover plate is available upon request. Power Feed 22mm diameter hole located 2 inches from one end of the fixture, on top of the profile. If a different location is required, please specify. LED Driver Remote driver must be installed into a metal enclosure (supplied by others). Maximum distance between the power supply and the last fixture on the circuit is 30' using a 18-gauge wire. For more than 30', the gauge of the wire must be determined by a certified professional. The length of the fixture specified must be considered within the maximum distance of 30'. Provisions must be made on site for accessibility to the power supplies. *Electronic Class II driver, 120V/ 277V/ 347V(optional). Dimming driver 0-10V (10-100%), Lutron Hi-Lume A type dimming Emergency Inverter Compatible To be installed remotely but provided by others, can be located up to 250 away from the fixture. Emergency Circuit Wiring Upon request. Fluorescent Ballast Electronic high-power factor ballast. Specify 120V, 277V, 347V. Ballast is pre-wired with leads to one end of fixture. Ballast is positioned behind the lamp insert and is fully accessible from below. 0-10V, Lutron 3-wire or Lutron digital dimming options are available. *Lutron dimming ballast is used as standard 120V/ 277V/ 347V. Emergency Ballast To be installed remotely. Only 1 emergency ballast for every 4 (flush) and/or 5 (flush or overlap) insert can be integral. Emergency Circuit Wiring Upon request. Emergency Testing Switch is installed on the side of the emergency ballast equipped fixture. Fixture integrated occupancy and daylight harvesting sensors mounted directly into the lighting fixture. ZANEEN offers a wired version of these lighting controls which will work independently and are able to control a limited number of lamps (LED or fluorescent). This utilizes passive infrared (PIR) technology with Auto ON/Auto OFF operation and an adjustable Time Delay. The Sensor Head measures the room illumination and when activated will turn the lights OFF for increased energy savings. Operating temperature range: 0 C - 55 C (32F 131F) Maximum Load Rating: - Fluorescent Ballasts 800VA at 120Vac - Fluorescent Ballasts 1200VA at 277Vac - LED 650W at 120Vac Time Delay: 30 sec to 30 min. Photo Cell range: 0 to 120 footcandles Sensor Head: Length = 50.62 mm (2 ), Width = 24.41 mm (15/16 ), Height = 21.26 mm (13/16 ) Power Pack: Length = 190 mm (7 1/2 ), Width = 25 mm (1 ), Height = 26 mm (1 ) WARRANTY Zaneen provides a limited warranty from date of purchase to original purchaser. LED Inserts : 5 year Rated for 50,000 hours at 70% lumen output (L70) LED Driver : 5 year Fluorescent / Ballast : 5 year Dimming Ballast : 3 year 12V Transformer : 1 year Non-Electrical Components : 1 year Page 3 of 8
INSERTS AR INSERTS LED Code Color Temp. (K) Wattage Voltage Lumen CRI Length Dimensions L38163-_ L38164-_ 37W 37W 5680lm 6000lm 2270mm (7'-5 3/8") 2270mm (7'-5 3/8") L38161-_ L38162-_ 33W 33W 4970lm 5250lm 1980mm (6'-5 15/16") 1980mm (6'-5 15/16") L38159-_ L38160-_ L38157-_ L38158-_ 28W 28W 23W 23W 120Vac* 4260lm 4500lm 3550lm 3750lm 1700mm (5'-6 15/16") 1700mm (5'-6 15/16") 1420mm (4'-7 7/8") 1420mm (4'-7 7/8") Length L38155-_ L38156-_ 19W 19W 2840lm 3000lm 1140mm (3'-8 7/8") 1140mm (3'-8 7/8") *LED driver included To complete the above codes add suffix according to the example Phase 0-10V ORDER-EXAMPLE: DIMMING DP DV L38207- DV Refer to page 5 for finishes 0-10V Fluorescent Overlap Flush Lamp Insert Position S1 H1 Standard Output T5: 21W, 28W, 35W High Output T5: 39W, 54W 1-Lamp 1-Lamp 2-Lamp (28W/54W) Emergency Standard Output T5: 21W, 28W, 35W High Output T5: 39W, 54W WIRED LIGHTING CONTROL Wired LC Code Sensor Head Operating Temprature Max. Load Rate Time Delay Photo Cell Range DOS Fixture Mounted PIR Sensor Head 0 C - 55 C (32F - 131F) Fluorescent Ballast 800VA at 120Vac Fluorescent Ballast 1200VA at 277Vac LED 650W at 120Vac 30 sec to 30 min. 0-120 footcandles (13/16") 21.3mm Dimensions 50.6mm (2") 190x25x26mm / 7 ½ x 1 x 1 Power Pack 24.4mm (15/16") Page 4 of 8
35 Idaho Profile System - Trimless ELECTRICAL OPTIONS LED DRIVERS* Dimmable Max. Wattage Voltage Dimensions (mm/inch) DP DV Phase dimming 0-10V dimming 100W 100W 120-277V / 24Vdc 347V (*Optional) L.318x W.102x H.50.8mm /L.12 1/2 x W.4 x H.2 DL Lutron Hi-Lume A Series 40W 120-277V / 24Vdc L.318x W.102x H.50.8mm /L.12 1/2 x W.4 x H.2 FLUORESCENT BALLASTS Non-Dimm/Dimmable T5SO /Wattages T5HO /Wattages Voltage Dimensions (mm/inch) SO HO Standard Output non-dimm High Output non-dimm 21-28-35W --- --- 39-54W 120V-277V 347V (*Optional) INTEGRAL DIM1 DIME DIME3 DIM3D DIM3D3 DIMEH 0-10V dimming Lutron Eco System(10%) Lutron Eco System 3 wire (10%) Lutron Hi-Lume 3D (1%) Lutron Hi-Lume 3 wire (1%) Lutron Eco System H series (1%) 21-28W 54W 21-28-35W 39-54W 21-28-35W 39-54W 21-28W 39-54W 21-28W 39-54W 21-28W 39-54W 120V-277V 347V (*Optional) INTEGRAL EM Emergency 90 minutes operation 21-28-35W 39-54W 120V-277V L.571.5x W.30x H.30mm /L.22 1/4 x W.1 3/16 x H.1 3/16 COMPONENTS 6 12/16 172mm Profile *Max. 8'-0" (2438mm) lengths Mounting Bracket *10mm/ 12.5mm/ 15mm 4 3/16 107mm Diffuser *Max. 8'-0" (2438mm) length Linear Coupler 80 End Cap Page 5 of 8
WIRING DIAGRAMS FOR AR LED 0-10V DIMMING RED/ 0-10V DRIVER 0-10Vdc 24Vdc + _ GRAY PURPLE BLUE *DIMMER RED *Zaneen recommends Diva 0-10V (DVTV) dimmer. * This diagram applies only to Diva 0-10V (DVTV) dimmer. + _ LED LIGHT ENGINE LUTRON ECO SYSTEM DIGITAL DIMMING GROUND GREEN HI-LUME A SERIES + RED _ LED LIGHT ENGINE GROUND E1 - PURPLE 1 LUTRON ECOSYSTEM BUS E2 - PURPLE 2 LUTRON 3-WIRE DIMMER CONTROL GREEN 3-WIRE CONNECTION DIMMER RED YELLOW OR ORANGE ORANGE DIMMING DRIVER + _ LED LIGHT ENGINE Page 6 of 8
WIRING DIAGRAMS FOR FLUORESCENT T5 SO AND HO 0-10V DIMMING RED/ 0-10V BALLAST 0-10Vdc 24Vdc + _ GRAY PURPLE BLUE *DIMMER RED *Zaneen recommends Diva 0-10V (DVTV) dimmer. * This diagram applies only to Diva 0-10V (DVTV) dimmer. FLUORESCENT FIXTURE LUTRON ECO SYSTEM DIGITAL DIMMING BALLAST E1 - PURPLE 1 E2 - PURPLE 2 LUTRON ECOSYSTEM BUS FLUORESCENT FIXTURE LUTRON 3-WIRE DIMMER CONTROL GREEN 3-WIRE CONNECTION DIMMER RED YELLOW OR ORANGE ORANGE DIMMING BALLAST FLUORESCENT FIXTURE Page 7 of 8
WIRING DIAGRAMS FOR LIGHTING CONTROL WIRED LIGHTING CONTROL Hot (Black) OSF10-PPW Red Line 120/277VAC 60Hz White Load Neutral (White) Integral to Fixture Page 8 of 8