Drying ovens ED 53 - Drying oven with natural convection Routine drying and sterilization applications up to 300 C (572 F) and storage at precisely controlled elevated temperatures are the strengths of ED drying ovens. Because of the natural convection with a high rate of air exchange, thermal processes run with significantly increased efficiency. Performance features and equipment : Electronically controlled APT.line preheating chamber assuring temperature accuracy and reproducible results Temperature range 5 C (32 ºF) above ambient temperature up to 300 C (572 F) Digital temperature setting with an accuracy of one degree DS controller with integrated timer 0 to 99 h Independent adjustable temperature safety device class 2 (DIN 12880), with visual temperature alarm Adjustable front ventilation flap slide and rear exhaust ø 50 mm (1.97 inch) With or without RS 422 Interface for use with optional GMP/GLP and FDA guideline 21 CFR Part 11 compliant APT-CM DataControlSystem software Units up to 115 liters are stackable 2 chrome-plated racks included BINDER test certificate 04/02/2009
Technical specification ED 53 ED 53 Exterior dimensions Width (mm/inch) 634 / 25.0 Height (inclusive feet/castors) (mm/inch) 617 / 24.3 Depth (mm/inch) 575 / 22.6 plus door handle, I-panel and exhaust duct (mm/inch) 85 / 3.4 Wall clearance rear (mm/inch) 100 / 3.9 Wall clearance side (mm/inch) 160 / 6.3 Exhaust duct outer-ø (mm/inch) 52 / 2.1 Steam space volume (l/cu.ft.) 70 / 2.5 Number of doors 1 Interior dimensions Width (mm/inch) 400 / 15.8 Height (mm/inch) 400 / 15.8 Depth (mm/inch) 330 / 13.0 Interior volume (l/cu.ft.) 53 / 1.9 Racks, chrome-plated (number standard/max.) 2 / 5 Load per rack (kg/lbs.) 15 / 33 Permitted total load (kg/lbs.) 40 / 88 Weight of the unit (empty) (kg/lbs.) 42 / 93 Temperature data Temperature range, 5 C (41 F) above ambient up to ( C / F) 300 / 572 Temperature variation 1) at 70 C (± C) 2 at 150 C (± C) 3.2 at 300 C (± C) 4.5 Temperature fluctuation (± C) at 70 C 0.3 Heating up time 2) to 70 C (Min.) 14 to 150 C (Min.) 27 to 250 C (Min.) 61 Recov. time after door was opened for 30 sec. 2) at 70 C (Min.) 2 at 150 C (Min.) 6 at 300 C (Min.) 11 Air change data Air change at 70 C (x/h) 8 at 150 C (x/h) 12 at 300 C (x/h) 20 Electrical data Housing protection acc. to EN 60529 IP 20 Nominal voltage (±10 %) 50 / 60 Hz (V) 230 Nominal power (kw) 1.2 Energy consumption at 70 C (W) 60 at 150 C (W) 210 at 300 C (W) 600 1) value without window 2) up to 98 % of the set value All technical data are specified for units with standard equipment at an ambient temperature of 25 C and a voltage fluctuation of ±10 %. The temperature data are determinated in accordance to factory standard following DIN 12880 respecting the recommended wall clearances of 10 % of the height, width and depth of the inner chamber.all indications are average values, typical for units produced in series. We reserve the right to alter technical specifications at all times. 04/02/2009 BINDER Inc. 3500 Sunrise Highway,Suite D214 Great River, NY 11739 Address: 3500 Sunrise Highway,Suite D214 Great River, NY 11739, USA Contact: Phone: +1 (631) 224 4340 Toll free: +1 (866) 885 9794 Fax: +1 (631) 224 4354 us-sales@binder-world.com www.binder-world.us
ptions and accessories ED series Access ports With silicon plugs for inserting external measuring devices into the chamber. Access ports with 10, 30, 50, 100 mm (0.4, 1.2, 2, 3.94 inch) diameter. Door with window and interior lighting For optimum process control in the interior, available for all equipment sizes. Lockable door Prevents unauthorized access and interference with processes in the chamber. Calibration certificates and validation BINDER can significantly reduce the time and effort needed for equipment qualification. We draw on unparalleled knowledge of our equipment applications and years of experience in certification. 04/02/2009 BINDER Inc. 3500 Sunrise Highway,Suite D214 Great River, NY 11739 Address: 3500 Sunrise Highway,Suite D214 Great River, NY 11739, USA Contact: Phone: +1 (631) 224 4340 Toll free: +1 (866) 885 9794 Fax: +1 (631) 224 4354 us-sales@binder-world.com www.binder-world.us
ptions and accessories ED series Access port with silicone plugs, 10 mm (0.39 inch), 30 mm (1.18 inch), 50 mm (1.97 inch), 100 mm (3.94 inch) Anti-slip rubber pads for safe stacking (4 pieces) ver temperature alarm, acoustic, can be switched off. Temperature limit can be set at the independent, adjustable temperature safety device class 2 Independent adjustable temperature safety device, Class 3.1 (DIN 12880) Analog temperature output, 4-20 ma, with 6 - pin DIN socket (output not adjustable) Temperature measurement acc. to DIN 12880 (27 measuring points) at 150 C (302 F) or at specified temperature with measuring protocol and certificate Factory calibration certificate. Measurement in center of chamber at 150 C (302 F) or at specified testing temperature Extension to factory calibration certificate. Each additional measurement at an additional measuring point or temperature Rack, chrome - plated or stainless steel Shelf, perforated, stainless steel Lockable door FKM door gasket Door with window and interior lighting, 15 W (230 x 230 mm / 9.06 x 9.06 inch) ED 53 04/02/2009 BINDER Inc. 3500 Sunrise Highway,Suite D214 Great River, NY 11739 Address: 3500 Sunrise Highway,Suite D214 Great River, NY 11739, USA Contact: Phone: +1 (631) 224 4340 Toll free: +1 (866) 885 9794 Fax: +1 (631) 224 4354 us-sales@binder-world.com www.binder-world.us
FD series 53 Heating ovens Drying and heating chambers with forced convection A BINDER FD series drying oven is always used when fast drying and sterilization is required. Thanks to its fully homogeneous temperature distribution, quick dynamics and powerful fan, it saves valuable time. Advantages: Fast, even tempering Wide temperature range Quality "Made in Germany" Areas of application: Electronics / Basic Research / Semiconductor Industry Research Institutes Plastics Industry
Customer benefits Features Customer benefits Characteristics APT.line Quick drying Identical test conditions throughout the chamber interior Independent of specimen size and quantity APT.line for maximum precision Uniform circulation even under full load Homogeneous temperature conditions throughout specimen material Temperature range Inner chamber concept Standard equipment Quality Accessories and Services Broad range of applications Short warm up times Maximum occupational safety Easy loading and unloading of specimen material Easy cleaning Reliable, easy handling Reliable devices with long service lives Short delivery times Minimal maintenance and operating costs Flexible solution in terms of size, type and equipment ptimal solution for numerous applications BINDER INDIVIDUAL for customer-specific solutions Worldwide BINDER Service Standard up to 300 C Large power reserves Inner chamber made of stainless steel Very tight door closure with 2-point door latch Low heat dissipation due to 60 mm insulation Rack with tilt protection No permanent fixtures Comprehensive standards Microprocessor control Ergonomically positioned controller. PT 100 temperature sensor Premium quality Highly automated Series production High-quality materials, state-of-the-art production technology High standard according to DIN 12880 (27-point measurement) Comprehensive product portfolio Size 23 to 240 liters Additional product lines with humidity, light, C2 or vacuum Voltage variants (UL) and certificates Various options: Door with viewing window, access ports, reinforced shelves, Data Logger Kits Worldwide service network BINDER GmbH P Box 102 D-78502 Tuttlingen Address: Im Mittleren Ösch 5 D-78532 Tuttlingen, Germany
Performance characteristics Electronically controlled APT.line preheating chamber assuring temperature accuracy and reproducible results Temperature range from 5 C above ambient temperature to 300 C DS control with integrated timer 0 to 99 hrs Digital temperature setting with an accuracy of one degree Independent adjustable temperature safety device class 2 (DIN 12880), with visual temperature alarm Adjustable front ventilation flap slide and rear exhaust Ø 50 mm (1.97 inch) Units up to 115 liters are stackable 2 chrome-plated racks included BINDER test confirmation BINDER GmbH P Box 102 D-78502 Tuttlingen Address: Im Mittleren Ösch 5 D-78532 Tuttlingen, Germany
Specifications FD 53 Exterior dimensions Width (mm) 635 Height (incl. feet) (mm) 620 Depth (mm) 575 Plus door handle and connection (mm) 105 Wall clearance, rear (mm) 100 Wall clearance, side (mm) 160 Exhaust duct (outer Ø mm) 52 Steam space volume (l) 77 Number of doors (ea.) 1 Interior dimensions Width (mm) 400 Height (mm) 400 Depth (mm) 330 Interior volume (l) 53 Racks (number standard/max.) 2 / 5 Load per rack (kg) 15 Permitted total load (kg) 40 Weight (empty) (kg) 44 Temperature data Temperature range approx. 5 C above ambient temperature to ( C) 300 Temperature variation at 70 C (± K) 0,8 at 150 C (± K) 2 at 300 C (± K) 3,7 Temperature fluctuation at 70 C (± K) 0,3 Heating up time 1) to 70 C (min.) 7 to 150 C (min.) 24 to 300 C (min.) 60 Recovery time after doors were open for 30 sec. 1) at 70 C (min.) 2 at 150 C (min.) 5 at 300 C (min.) 9 BINDER GmbH P Box 102 D-78502 Tuttlingen Address: Im Mittleren Ösch 5 D-78532 Tuttlingen, Germany
Specifications FD 53 Ventilation data Ventilation at 70 C (x/h) 59 at 150 C (x/h) 64 at 300 C (x/h) 53 Electrical data IP protection class acc. to EN 60529 IP 20 Voltage (± 10%) 50/60 Hz (V) 230 Nominal power (kw) 1,2 Energy consumption at 70 C (W) 172 at 150 C (W) 429 at 300 C (W) 951 1) To 98% of the set value All technical data are specified for units with standard equipment at an ambient temperature of 25 C and a line voltage fluctuation of ±10%. The temperature data is determined in accordance to factory standard following DIN 12880, respecting the recommended wall clearances of 10% of the height, width and depth of the inner chamber. All figures are typical average values for series devices. We reserve the right to alter technical specifications at any time. BINDER GmbH P Box 102 D-78502 Tuttlingen Address: Im Mittleren Ösch 5 D-78532 Tuttlingen, Germany
ptions Numerous access ports With silicone plugs for introducing external measuring instruments into the chamber, access ports with 10, 30, 50, 100 mm diameters. Door with window and interior lighting For optimal process control in the inner chamber, available for all device sizes. Door lock Prevents unauthorized access to the process sequences in the chamber. Calibration certificate & validation BINDER can significantly reduce the workload in qualifying and validating devices. Nobody knows our devices as well and has as much experience in certifications as we do. BINDER GmbH P Box 102 D-78502 Tuttlingen Address: Im Mittleren Ösch 5 D-78532 Tuttlingen, Germany
ptions FD 53 Access ports with silicone plug, 10, 30, 50, 100 mm Anti-slip rubber pads for safe stacking (1 set of 4 pieces) Independent adjustable temperature safety device class 3.1 (DIN 12880) with optical alarm Analog temperature output, 4-20 ma with 6-pin DIN socket (output not adjustable) ver temperature alarm, audible, can be switched off. Temperature limit can be set at the independent, adjustable temperature safety device Securing elements for additional fastening of racks (1 set of 4 pieces) Temperature measurement acc. to DIN 12880 at 150 C or at specified testing temperature with measuring protocol and certificate Factory calibration certificate. Measurement in center of chamber at 150 C (302 F) or at specified testing temperature Extension to factory calibration certificate. Each additional measurement at additional measuring point or temperature Data Logger Kit T 350: For continuous temperature recording of 0 C to 350 C. Kit includes 1 data logger, PT 100 sensor with 2 m Teflon extension cable and 1 fixture for mounting to the BINDER unit Data Logger converter cable RS 232 to USB 2.0 Data Logger Software: Configuration and evaluation software for all BINDER Data Logger Kits, incl. data cable Rack, chrome-plated Rack, stainless steel Shelf, perforated, stainless steel Locking door handle with key Door gasket, FKM (Viton) Door with window 230 x 230 mm and interior lighting (15 W) BINDER GmbH P Box 102 D-78502 Tuttlingen Address: Im Mittleren Ösch 5 D-78532 Tuttlingen, Germany