NEVER STOP LEARNING, NEVER STOP IMPROVING, AND NEVER, EVER STOP FISHING.

Thnk You Thnk you for hoosing MotorGuide, one of the finest trolling motors vilble. Yers of experiene hve been ommitted to the gol of produing the finest qulity produts. This led to MotorGuide's reputtion for strit qulity ontrol, exellene, durbility, long lsting performne nd being the best t providing fter the sle servie nd support. Plese red this mnul refully before operting your motor. This mnul hs been prepred to ssist you in the opertion, sfe use, nd re of your trolling motor. Agin, thnk you for your onfidene in MotorGuide. NEVER STOP LEARNING, NEVER STOP IMPROVING, AND NEVER, EVER STOP FISHING. Wrrnty Messge The produt you hve purhsed omes with Two Yer Limited Wrrnty from MotorGuide, the terms of the poliy re set forth in the Wrrnty Informtion setion of this mnul. The poliy sttement ontins desription of the durtion of overge, importnt dislimers nd limittions of dmges, nd other relted informtion. Plese review this importnt informtion. The desription nd speifitions ontined herein were in effet t the time this mnul ws pproved for printing. Merury Mrine, whose poliy is one of ontinued improvement, reserves the right to disontinue models t ny time, to hnge speifitions, designs, methods, or proedures without notie nd without inurring obligtion. Freshwter/Sltwter

Merury, Merury Mrine, MerCruiser, Merury MerCruiser, Merury Ring, MotorGuide, Merury Preision Prts, Merury Propellers, Mriner, Quiksilver, #1 On The Wter, Alph, Brvo, Brvo Two, Pro Mx, OptiMx, Sport Jet, K Plnes, MerCthode, RideGuide, SmrtCrft, Totl Commnd, VesselView, Zero Effort, Zeus, M with Wves logo, Merury with Wves logo, nd SmrtCrft logo re ll registered trdemrks of Brunswik Corportion. Merury Produt Protetion logo is registered servie mrk of Brunswik Corportion. ii

Generl Informtion MotorGuide Limited Wrrnty...1 Generl Informtion...4 Reording Seril Number...5 Boter's Responsibilities...6 Pssenger Sfety Messge...6 Sfe Boting Suggestions...7 Component Identifition...8 Extending nd Retrting the Hndle...10 Instlling the Propeller...11 Wiring nd Bttery Bttery Preutions...12 Stndrd Prties nd Proedures...12 Bttery Reommendtions...12 Wire Color Code Abbrevitions...13 Wire nd Cble Routing...13 Mount Instlltion Trnsom Mount Instlltion...18 Pontoon Mount Instlltion...18 Bow Mount Instlltion...18 Bow Mount Opertion Instlling the Motor into the Mount...21 Removing the Motor from the Mount...21 Rising nd Lowering the Trolling Motor...22 Adjusting the Steering Tension (Hnd Operted Motors)...23 Adjusting the Motor Depth...24 iii

Trolling Motor Opertion Diretionl Inditor...26 Speed Control...27 Constnt/Momentry/High Bypss...27 Twist Tiller Speed Control...28 Permnent Foot Pedl Mounting...28 Mintenne Trolling Motor Cre...30 Inspetion nd Mintenne Shedule...30 Storge Preprtion...31 Bttery Inspetion...32 Propeller Replement...32 Gret White Sltwter Models Only...33 iv

GENERAL INFORMATION MotorGuide Limited Wrrnty KEEP YOUR ORIGINAL PURCHASE RECEIPT OR BILL OF SALE. 1. For reretionl use ustomers, MotorGuide eletri trolling motors re wrrnted to the originl retil purhser to be free from defets in mteril or workmnship for two (2) yers. 2. To obtin wrrnty servie, the purhser should deliver or return the unit (postge prepid nd insured) to ny uthorized MotorGuide servie deler. DO NOT RETURN TO PLACE OF PURCHASE unless they re n uthorized servie enter. Produts returned by mil should be refully pkged nd inlude note desribing the nture of the problem nd/or servie requested, ustomer ddress, nd phone number. A opy of the reeipt, Bill of Sle, registrtion verifition, or other proof of purhse is required with the return of the produt for wrrnty onsidertion. Wrrnty lims will not be epted without presenttion of purhse reeipt for trolling motor, other verifition of registrtion, or Bill of Sle for bot pkge. 3. MotorGuide, t its disretion, will repir or reple items overed under the terms of this wrrnty. Neither MotorGuide nor MotorGuide servie delers re responsible for dmges to MotorGuide produts due to repirs performed by nyone other thn n uthorized MotorGuide servie deler. Neither MotorGuide nor Merury Mrine is responsible for filure or dmge used by improper instlltion, setup, preprtion, or previous servie or repir errors. 4. For ommeril use nd government use ustomers, MotorGuide eletri trolling motors re wrrnted to the originl retil purhser to be free from defets in mteril or workmnship for one (1) yer. Commeril use is defined s ny work or employment relted use of the produt, or ny use of the produt whih genertes inome, for ny prt of the wrrnty period, even if the produt is only osionlly used for suh purpose suh s Rentl Fleets, Guides, Fish Cmps, or similr opertions. Wrrnty is not trnsferble to ny subsequent purhser. The Merury Produt Protetion pln is not vilble to ommeril use or government use ustomers. 1

GENERAL INFORMATION 5. Wrrnty overge is vilble to ustomers tht purhse from n uthorized deler or retiler tht is uthorized by MotorGuide Mrine to distribute the produt in the ountry in whih the sle ourred. Wrrnty overge nd durtion vries by the ountry in whih the owner resides. This wrrnty pplies to MotorGuide trolling motors sold nd used in the United Sttes. This Limited Wrrnty begins on the dte the produt is first sold to purhser or the dte on whih the produt is first put into servie, whihever ours first. MotorGuide essories re overed by this Limited Wrrnty for overge period of one (1) yer from the dte of retil sle. The repir or replement of prts, or the performne of servie under this wrrnty, does not extend the life of this wrrnty beyond its originl expirtion dte. Promotionl wrrnties re not inluded in this sttement nd overge my vry by promotion. Produt either sold or put into servie more thn six yers from dte of mnufture is exluded from wrrnty overge. 6. This wrrnty does not pply to norml worn prts, for exmple, worn bles, djustments, or produt dmge due to; 1) neglet, lk of mintenne, ident, bnorml opertion, or improper instlltion or servie; 2) buse, suh s, bent metl olumns, bent rmture shfts, broken ontrol bles, et., idents, modifitions, misuse, exessive wer or dmge used by n owner s filure to provide resonble nd neessry instlltion or re; 3) use of n essory or prt not mnuftured by MotorGuide or Merury; 4) ltertion or removl of prts; 5) opening the lower unit (motor) by nyone other thn n uthorized MotorGuide servie enter will void this wrrnty. 7. We reserve the right to improve the design of ny trolling motor without ssuming ny obligtion to modify ny trolling motor previously mnuftured. 2

GENERAL INFORMATION 8. All serilized "Servie Repir" trolling motors reeive one (1) yer wrrnty. Nonserilized "Servie Repir" eletri trolling motors re NOT wrrnted. "Servie Repir" motor denotes trolling motor sold by MotorGuide tht my be used, but hs been inspeted nd my hve hd minor repirs. Originl retil purhser of "Servie Repir" motor is the first purhser of the motor fter it is denoted s "Servie Repir." "Servie Repir" motors hve blue stiker on the bttery ble nd box denoting "Mnufturer Certified Servie Repir Motor." 9. This wrrnty will not pply to 1) hul out, lunh, towing nd storge, trnsporttion hrges nd/or trvel time, telephone or rentl hrges of ny type, inonveniene, or loss of time or inome, or other onsequentil dmges; or 2) removl or replement of bot prtitions or mteril beuse of bot design for neessry ess to the Produt; or 3) disonnetion nd reonnetion of hrd wired trolling motors. 10. TERMINATION OF COVERAGE: Wrrnty overge my be terminted for repossessed produt, or produt purhsed t ution, from slvge yrd, from liquidtor, from n insurne ompny, from unuthorized mrine delers or botbuilders, or other third prty entities. 11. ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED FROM THIS WARRANTY, WARRANTIES OF MERCHANTABILITY AND FITNESS ARE EXCLUDED FROM THIS WARRANTY, IMPLIED WARRANTIES ARE LIMITED TO THE LIFE OF THIS WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE. 3

Generl Informtion GENERAL INFORMATION Plese red nd retin this mnul. The informtion within desribes the proper proedures for sfely instlling, operting, nd mintining your motor. The desription nd speifitions ontined herein were in effet t the time this mnul ws pproved for printing. MotorGuide, whose poliy is one of ontinul improvement, reserves the right to disontinue models t ny time, to hnge speifitions, designs, nd methods of proedure without notie nd without inurring obligtion. Sfety nd operting informtion tht is prtied long with good ommon sense n help prevent personl injury nd produt dmge. SAFETY DO'S AND DON'TS Do not llow hildren to operte the trolling motor without dult supervision. Do not modify the unit in ny wy or dd essories other thn pproved MotorGuide essories. Do not power wsh your trolling motor. Do disonnet the power from the motor when repling the propeller, removing debris round the propeller, hrging btteries, putting your bot on triler, or when the motor is not in use. Do verify the foot pedl is seured nd the motor is seurely loked into the stowed position when using gsoline motor to move to nother lotion, or when putting your bot on triler. Do seure loose items on your bot before trveling t high speeds ross the wter. HOW TO USE THIS MANUAL Review the following informtion refully. These noties will lert you to potentil dngers nd importnt informtion. The observne of WARNINGS nd CAUTIONS lone does not eliminte the possibility of personl injury or produt dmge. Your lose ttention to the performne of reommended servie proedures nd the prtie of responsible personl sfety re mjor ident prevention mesures. 4

GENERAL INFORMATION! WARNING Filure to follow sfety WARNING n result in bodily injury. Reording Seril Number Reord the seril number for future referene. TRANSOM MOUNT FOOT CONTROL MODEL The trnsom mount seril number del is loted underneth the bottom over. b 46206 - Seril number b - Model identifition number - Voltge 5

GENERAL INFORMATION BOW MOUNT HAND CONTROL MODEL The bow mount seril number del is loted underneth the bottom over. b 46217 - Seril number b - Model identifition number - Voltge Boter's Responsibilities The opertor (driver) is responsible for the orret nd sfe opertion of the bot nd sfety of its oupnts nd generl publi. It is strongly reommended tht eh opertor (driver) red nd understnd this entire mnul before operting the trolling motor. Be sure t lest one dditionl person on bord is instruted in the bsi opertion of the trolling motor in se the driver is unble to operte the bot. Pssenger Sfety Messge Whenever the bot is in motion, observe the lotion of ll pssengers. A sudden redution in bot speed, suh s shrp hnge of bot diretion, ould throw them off the bot. 6

GENERAL INFORMATION Sfe Boting Suggestions In order to sfely enjoy the wterwys, fmilirize yourself with lol nd other governmentl boting regultions nd restritions, nd onsider the following suggestions. Use flottion devies. It is the lw to hve n pproved personl flottion devie of suitble size for eh person bord nd hve it redily essible. Do not overlod your bot. Most bots re rted nd ertified for mximum lod (weight) pities, refer to your bot pity plte. If in doubt, ontt your deler or the bot's mnufturer. Perform sfety heks nd required mintenne. Follow regulr shedule nd ensure ll repirs re mde properly. Never be under the influene of lohol or drugs while boting (it is the lw). Alohol or drug use impirs your judgment nd gretly redues your bility to ret quikly. Pssenger bording. Stop the trolling motor whenever pssengers re bording or unloding. Be lert. The opertor of the bot is responsible by lw to mintin proper lookout by sight nd hering. The opertor must hve n unobstruted view prtiulrly to the front. No pssengers, lod, or fishing sets should blok the opertors view when operting the bot. Underwter hzrds. Redue speed nd proeed with ution whenever nvigting in shllow wter. Tripping hzrds. To void trip hzrd, route ll bles nd wiring netly nd out of the wy. Report idents. Bot opertors re required by lw to file Boting Aident Report with their stte boting lw enforement geny when their bot is involved in ertin boting idents. A boting ident must be reported if 1) there is loss of life or probble loss of life, 2) there is personl injury requiring medil tretment beyond first id, 3) there is dmge to bots or other property where the dmge vlue exeeds $500.00 or 4) there is omplete loss of the bot. Seek further ssistne from lol lw enforement. 7

GENERAL INFORMATION Component Identifition TRANSOM MOUNT FOOT CONTROL b l d e f g h k i j 46220 - Diretionl inditor b - Seril number del - Tilt lth d - Clmp brket (Bulldog model) e - Foot pedl f - Three position swith g - Speed ontrol h - Bttery bles i - Momentry swith j - Lower unit k - Propeller l - Steering tension knob 8

GENERAL INFORMATION BOW MOUNT HAND CONTROL l b f d k e j i h g 46221 BOW MOUNT FOOT CONTROL b d l e f g i h k - Extendble speed ontrol hndle b - Seril number del - On/off swith d - Bttery bles e - Mount f - Brekwy djustment knob g - Propeller h - Lower unit i - Anode j - Brket door knob k - Steering tension knob l - Depth djustment ollr - Diretionl inditor b - Seril number del - Lokslide relese hndle d - Mount e - Three position swith f - Speed ontrol g - Foot pedl h - Momentry swith i - Bttery bles j - Propeller k - Lower unit l - Brket door knob j 46271 9

GENERAL INFORMATION Extending nd Retrting the Hndle 1. Speed nd diretion ontrol re provided through the tiller hndle on the bow mount nd trnsom mount hnd ontrol models. - Tiller hndle 46265 2. Extend or retrt the hndle to the desired length. - Speed nd diretionl ontrol hndle 46270 10

GENERAL INFORMATION Instlling the Propeller! WARNING Performing servie or mintenne without first disonneting the bttery n use produt dmge, personl injury, or deth due to fire, explosion, eletril shok, or unexpeted motor strting. Alwys disonnet the bttery bles from the bttery before mintining, serviing, instlling, or removing motor omponents. 1. Rotte the motor shft to insert the propeller pin horizontlly. - Propeller pin 45685 2. Instll the propeller onto the motor shft by engging the propeller onto the propeller pin. 3. Instll the propeller nut. Tighten seurely. b d 45696 - Propeller pin b - Propeller - Propeller nut d - Propeller wrenh 4. Use MotorGuide propeller wrenh or pliers to tighten the propeller nut nother ¼ turn. Reommended MotorGuide Aessory Desription MotorGuide prop wrenh kit Prt Number MGA050B6 11

Bttery Preutions WIRING AND BATTERY! WARNING An operting or hrging bttery produes gs tht n ignite nd explode, sprying out sulfuri id, whih n use severe burns. Ventilte the re round the bttery nd wer protetive equipment when hndling or serviing btteries. When hrging btteries, n explosive gs mixture forms in eh ell. Prt of this gs espes through holes in the vent plugs nd my form n explosive tmosphere round the bttery if ventiltion is poor. This explosive gs my remin in or round the bttery for severl hours fter it hs been hrged. Sprks or flmes n ignite this gs nd use n internl explosion, whih my shtter the bttery. The following preutions should be observed to prevent n explosion: 1. Do not smoke ner btteries being hrged or whih hve been hrged very reently. 2. Do not brek live iruits t terminls of btteries, beuse sprk usully ours t the point where live iruit is broken. Alwys be reful when onneting or disonneting ble lmps on hrgers. Poor onnetions re ommon use of eletril rs whih use explosions. 3. Do not reverse polrity of bttery terminl to ble onnetions. Stndrd Prties nd Proedures Do not use the min engine bttery to power the trolling motor. Disonnet the trolling motor from the bttery when hrging nd fter eh use. Route the trolling motor wires on the opposite side of the bot from other misellneous bot wiring. Connet bot essories diretly to the min engine bttery. Bttery Reommendtions Use 12 volt, deep yle mrine bttery. Instll 50 mp mnul reset iruit breker in line with the trolling motor positive leds within 180 m (72 in.) of the btteries. 12

WIRING AND BATTERY Use 13 mm (6 guge) bttery bles if extending the existing wire beyond the stndrd bttery ble. Reommended MotorGuide Aessory Desription Trolling motor power plug Trolling motor sp (reeptle) Prt Number 8M4000953 8M4000954 50 mp lligtor lips 8M4000287 6 guge bttery ble nd terminls with 50 mp mnul reset iruit breker MM309922T 50 mp mnul reset iruit breker MM5870 Wire Color Code Abbrevitions Wire Color Abbrevitions BLK Blk BLU Blue BRN Brown GRY Gry GRN Green ORN or ORG Ornge PNK Pink PPL or PUR Purple RED Red TAN Tn WHT White YEL Yellow LT or LIT Light DK or DRK Drk Wire nd Cble Routing Route trolling motor wires on the opposite side of the bot from other misellneous bot wiring (bow light wiring, spot light wiring, et.). Trnsduer instlltion should be instlled ording to the mnufturer s speifitions. To void interferene, bles should be routed seprtely from the trolling motor power bles. IMPORTANT: Do not route the trnsduer ble down the trolling motor power ord or foot pedl ssembly ble. Route the trnsduer ble down the rm of the mount, then into the bow onsole. Sensitive eletronis, depth finders in prtiulr, should be onneted diretly to the min engine bttery. If only one bttery system is used, then onnet with seprte bles. 13

WIRING AND BATTERY ESTABLISHING A COMMON GROUND MotorGuide reommends isolting the trolling motor bttery/btteries from the min engine bttery. Eletrolysis issues: Using the engine strting bttery s soure of power for ny trolling motor my use eletrolysis on metlli prts. If you hve followed the bttery wiring nd instlltion instrutions in this mnul nd your bot ontinues to hve eletrolysis issues, you will need to seprte the trolling motor from ny other bot eletronis. Remove the engine strting bttery from the wiring onfigurtion of the bot nd isolte the power iruit for your trolling motor. Estblish ommon ground: Common ground mens the ground for the min engine essories nd your trolling motor re onneted to the sme negtive ground terminl. Not hving ommon ground n use severe orrosion or eletrolysis. If left unheked, dmge my be used to your trolling motor nd bot. Estblishing ommon ground onnetion will llow inresed sensitivity nd improve detil on sonr disply. RECOMMENDATIONS Bttery type: The reommended bttery is 12 volt deep yle bttery. Ciruit protetion: MotorGuide reommends instlling 50 mp mnul reset iruit breker in line with the trolling motor positive leds within 180 m (72 in.) of the btteries. To order iruit breker kit, ontt your lol servie deler, request kit number MM5870. Wire size: For optimum performne, MotorGuide reommends the use of 13 mm (6 guge) wire if extending the existing wire beyond the stndrd bttery ble supplied with the produt. Bow plugs: For temporry trolling motor instlltions, MotorGuide reommends the use of qulity plug designed for mrine pplitions. 14

WIRING AND BATTERY Connet the red bttery led to the bttery positive (+) post nd the blk bttery led to the bttery negtive ( ) post. Instll 50 mp iruit breker in line with the positive led, s shown. d BLK 12 volt bttery hookup - Power ble b - 50 mp mnul reset iruit breker - Jumper wire d - Common ground RED b 37289 15

WIRING AND BATTERY Connet the blk bttery led from the power ble to the negtive ( ) post on bttery A nd the red led to the positive (+) post on bttery B. Connet jumper wire between the negtive ( ) post of bttery B nd the positive (+) post of bttery A. Instll 50 mp iruit breker in line with the positive led to bttery B, s shown. d BLK GRY Bttery A RED Bttery B b 37824 24 volt bttery hookup - Power ble b - 50 mp mnul reset iruit breker - Jumper wire d - Common ground 16

WIRING AND BATTERY Connet the blk bttery led from the power ble to the negtive ( ) post on bttery A. Connet the red bttery led from the power ble to the positive (+) post of bttery C. Connet jumper wire between the positive (+) post of bttery A to the negtive ( ) post of bttery B. Connet nother jumper wire between the positive (+) post of bttery B to the negtive ( ) post of bttery C. Instll 50 mp iruit breker in line with the positive bttery led. d BLK GRY Bttery A GRY Bttery B RED Bttery C b 37825 36 volt bttery hookup - Power ble b - 50 mp mnul reset iruit breker - Jumper wire d - Common ground 17

Trnsom Mount Instlltion TWIST TILLER MODELS MOUNT INSTALLATION 1. Clmp srews: The lmp srews llow for esy motor instlltion nd removl. Mount your motor on the trnsom nd then tighten the lmp srews seurely. 2. Tilt position pin: This pin llows you to djust the tilt of the motor. 3. Depth ollr djustment: The depth of the motor n be djusted up nd down by loosening the depth ollr knob. The depth ollr is loted on the olumn diretly bove the mount. After djusting to the position nd depth desired, tighten the knob. 4. Steering tension djustment: To djust the steering resistne, simply tighten or loosen the steering frition knob. Pontoon Mount Instlltion 1. Crefully selet the re on the dek to instll the mount. Choose n re where the mount will provide mple lerne for ll of the motor positions, inluding the running nd stowing positions. 2. Ple the mount bse on the surfe of the bot dek where it is to be mounted; use the mount bse s templte to mrk the lotion of the holes. 3. Drill mounting holes with 6.5 mm (0.25 in.) drill bit nd ler the holes of ny debris. Countersink the holes (only on fiberglss bots) nd gin ler ny remining debris from the holes. 4. Instll the four stinless steel mounting bolts through eh of the brket mounting holes. 5. Instll the four stinless steel wshers nd nuts on the bottom side of the dek nd tighten seurely. 6. The trolling motor n now be pled in the mount. Bow Mount Instlltion IMPORTANT: Choose n re on the dek tht provides 7.6 m (3 in.) lerne from the bow of the bot for ll motor positions, inluding deployed nd stowed positions. 18

MOUNT INSTALLATION 1. Selet n pproprite re on the dek of the bot to instll the mount. Ensure the forwrd mounting srews will not penetrte the hull. 41280 Mount on dek with 7.6 m (3 in.) lerne 2. Using Phillips hed srewdriver nd the deket srews provided in the hrdwre bg, seure the deket to the mount bse. (The deket for hevy duty spring mounts n be instlled lst.) 3. Use the bow mount bse s templte to mrk the lotion of the front mounting holes in the plsti deket nd the rer mounting holes on the mount bse. 38097 4. Drill the mounting holes with 6.5 mm (0.25 in.) dimeter drill bit. Remove ny debris. 19

MOUNT INSTALLATION 5. If using rubber mounting isoltors, drill eh mounting hole with 13 mm (0.5 in.) dimeter drill bit. 39076 NOTE: A rubber sper or wsher should be used between the bse of the mount nd the bot mounting surfe when the rubber isoltors re not used. 6. Insert the rubber mounting isoltors into the drilled holes. Position the wider side of the isoltor towrd the outside of the mount brket. 7. Ple the mount brket on the isoltors nd lign the holes. Instll the two longer srews into the front holes nd the two shorter srews into the rer holes. Tighten ll of the mounting srews with Phillips srewdriver. Do not tighten the mounting srews with n eletri srewdriver. NOTE: It is importnt tht the brket lies even ginst the isoltors before bolting it to the dek. If the mount is not even, it will bind s it is bolted down mking it diffiult or impossible to unlth. One instlled, the lth pins should snp firmly into ple nd relese esily with quik snp of the wrist nd light pull of the rope hndle. 8. When the brket is instlled, it should fsten seurely nd evenly with the lth pins nd relese with light, quik, pull of the rope hndle. 20

BOW MOUNT OPERATION Instlling the Motor into the Mount 1. Turn the brket door knob ounterlokwise nd open the brket door. 2. Ple the motor olumn into the brket nd lose the door. 3. Turn the brket door knob lokwise to tighten the motor olumn in the brket. - Motor olumn b - Brket door - Brket door knob b 46276 Removing the Motor from the Mount 1. Turn the brket door knob ounterlokwise to loosen nd open the brket door. 2. Remove the motor olumn from the brket nd lose the door. - Motor olumn b - Brket door - Brket door knob b 46276 21

BOW MOUNT OPERATION Rising nd Lowering the Trolling Motor! WARNING Rotting propellers n use serious injury or deth. Never strt or operte the motor out of wter.! CAUTION Moving prts, suh s hinges nd pivot points, n use serious injury. Keep wy from moving prts when stowing, deploying, or tilting the motor. RAISING THE MOTOR 1. Rise the motor by pulling on the mount rope hndle. Do not let the weight of the motor use it to drop. Mount rope 41443 2. Pull the rope hndle until the motor n be lid ross the mount into the stow position. 22

BOW MOUNT OPERATION 3. Apply pressure by pushing down on the top housing nd the shft to lok the motor into the stow position. 41441 LOWERING THE MOTOR Motor in the stowed position 1. Pull the rope hndle to lift the motor up. 2. Do not let the weight of the motor use it to drop. 3. Gently lower the motor into the wter. Adjusting the Steering Tension (Hnd Operted Motors) Loosen the steering tension knob until the motor olumn turns round freely. Tighten the steering tension knob to seure the motor olumn in ple. - Steering tension knob 46278 23

Adjusting the Motor Depth BOW MOUNT OPERATION Hnd operted motors: Loosen the depth djustment ollr so the motor olumn moves freely up nd down. Rise or lower the motor olumn until the propeller bldes re submerged 15 30 m (6 12 in.) below the wter surfe nd tighten the ollr. - Depth djustment ollr b - Brekwy knob b 46279 IMPORTANT: Adjust the brekwy knobs on the side of the mount so the motor will brekwy when enountering underwter obstles. Do not overtighten or lubrite the brekwy knob. 41496 24

BOW MOUNT OPERATION Foot operted motors: Loosen the brket door knob so the olumn moves freely up nd down. Rise or lower the motor olumn until the propeller bldes re submerged 15 30 m (6 12 in.) below the wter surfe nd tighten the door. - Brket door knob 46288 25

TROLLING MOTOR OPERATION Diretionl Inditor The inditor provides diretionl informtion t glne. e d b 46285 - Stright hed foot pedl in middle b - Right turn toe down; motor steers bot to right (ontinue to push ll the wy down for reverse) - Left turn heel down; motor steers bot to left (ontinue to press ll the wy down for reverse) d - Diretionl inditor rrows e - Diretionl inditor 26

TROLLING MOTOR OPERATION Speed Control FIVE-SPEED AND VARIABLE SPEED MOTORS Foot operted motors re either five speed or vrible speed models. Control the speed of your motor by rolling the speed ontrol knob with your hnd or foot until you reh the desired speed. Five-speed motor: The speed ontrol knob on five speed motor is numbered 1 5 nd llows you to selet one of five preset speeds. Vrible speed motor: The speed ontrol knob on vrible speed motor llows you the pbility of vrible speed seletions from off to high. b - Foot pedl b - Speed selet window (1 5) - Speed ontrol knob 46289 Constnt/Momentry/High Bypss Momentry swith: The momentry swith is loted on the top right side of the foot pedl. The momentry swith works in onjuntion with the three position swith when it is in momentry or high bypss position. Three-position swith: This three position swith provides three options for operting the motor: onstnt on, momentry, nd high bypss. Constnt on: This llows the motor to run ontinuously t the speed seleted by the speed ontrol knob without the use of the momentry swith. Momentry: This llows the motor to tivte with the momentry swith t the speed seleted by the speed ontrol knob. 27

TROLLING MOTOR OPERATION High-bypss: This will utomtilly deliver full thrust when the momentry swith is tivted. f b - Constnt on b - Momentry - High bypss d - Three position swith e - Speed ontrol knob f - Momentry swith e d 46291 Twist Tiller Speed Control Twist tiller hndle: Rotte the hndle lokwise for forwrd speeds nd ounterlokwise for reverse speeds. Toggle swith: Flip the toggle swith to " " to turn the motor on nd "O" to turn the motor off. This swith is vilble on vrible speed motors only. b d e - Twist tiller hndle b - Toggle swith - Forwrd speed d - Reverse speed e - Vrible speed del f - Five speed del f d 46286 Permnent Foot Pedl Mounting 1. Ple the foot pedl in the desired lotion on the bot dek. 2. Using 3 mm (7/64 in.) drill bit, drill holes through the holes in the foot pedl bse nd into the bot dek. 28

TROLLING MOTOR OPERATION 3. Use four #8 x 2 inh stinless srews nd srew the foot pedl bse seurely to the bot dek. 46287 29

Trolling Motor Cre MAINTENANCE To keep your trolling motor in the best operting ondition nd retin its dependbility, your trolling motor must reeive periodi inspetions nd mintenne. Keep it mintined properly to ensure the sfety of you nd your pssengers.! WARNING Negleting to inspet, mintin, or repir your trolling motor n result in produt dmge or serious injury or deth. Do not perform mintenne or servie on your trolling motor if you re not fmilir with the orret servie nd sfety proedures. Reord ll mintenne performed nd sve mintenne work orders nd reeipts. SELECTING REPLACEMENT PARTS Use only originl MotorGuide replement prts. Inspetion nd Mintenne Shedule BEFORE EACH USE Inspet for loose or orroded wiring onnetions. Chek the tightness of the bttery led onnetions. Chek the tightness of the propeller nut. Chek the propeller bldes for dmge. AFTER EACH USE Disonnet the bttery bles from the power soure or unplug the motor from the bot. Chek eh side of the propeller nd propeller shft for debris suh s weeds nd fishing line. Remove ll debris. Chek the tightness of the propeller nut. Rinse the trolling motor with len wter to remove dirt nd dust tht my srth the surfe. 30

MAINTENANCE EVERY 100 HOURS OF USE OR ANNUALLY Periodilly lubrite ll the pivot points with nonerosol, nonsolvent bsed lubrint. IMPORTANT: Never use n erosol lubrint to grese or oil ny prt of the unit. Mny erosol lubrints ontin hrmful propellnts tht n use dmge to vrious prts of the trolling motor. b d 41572 Lubrition points - Rer dek hnnel grooves b - Lokslide pin - Door knob shft d - Forwrd dek hnnel grooves Tube Ref No. Desription Where Used Prt No. 95 2-4-C with Teflon Pivot points 92-802859A 1 Chek the tightness of bolts, nuts, nd other fsteners. Inspet the bttery. Refer to Bttery Inspetion. Storge Preprtion The mjor onsidertion in prepring your trolling motor for storge is to protet it from orrosion nd dmge used by freezing of trpped wter. 31

MAINTENANCE Refer to the Mintenne Inspetion nd Mintenne Shedule setion nd omplete the pproprite re instrutions to prepre your trolling motor for storge. Store the trolling motor in dry lotion where it will not be ffeted by tempertures below 29 C ( 20 F). IMPORTANT: Trolling motors stored in tempertures below 0 C (32 F) should be operted slowly for minimum of 15 minutes before going bove 30% opertion. Bttery Inspetion The bttery should be inspeted t periodi intervls to ensure proper trolling motor opertion. IMPORTANT: Red the sfety nd mintenne instrutions whih ompny your bttery. 1. Ensure tht the bttery is seured to the vessel. 2. Ensure tht the bttery ble terminls re len, tight, nd orretly instlled. For instlltion instrutions, refer to Wiring nd Bttery. 3. Ensure tht the bttery is equipped with bttery box to prevent identl shorting of the bttery terminls. Propeller Replement! WARNING Performing servie or mintenne without first disonneting the bttery n use produt dmge, personl injury, or deth due to fire, explosion, eletril shok, or unexpeted motor strting. Alwys disonnet the bttery bles from the bttery before mintining, serviing, instlling, or removing motor omponents. REMOVING THE PROPELLER 1. Disonnet the bttery bles from the power soure. 2. While holding the propeller blde with one hnd, use propeller wrenh or pliers to remove the propeller nut. IMPORTANT: If the propeller nnot be removed esily, hold one blde nd use rubber mllet to lightly tp the bkside of the opposite blde. If the propeller nnot be removed, refer to Troubleshooting. 32

MAINTENANCE NOTE: If the propeller pin is bent, reple the propeller pin. b d 45696 - Propeller pin b - Propeller - Propeller nut d - Propeller wrenh Reommended MotorGuide Aessory Desription MotorGuide Prop Wrenh Kit Prt Number MGA050B6 INSTALLING THE PROPELLER 1. Rotte the motor shft to insert the propeller pin horizontlly. 2. Instll the propeller onto the motor shft by engging the propeller onto the propeller pin. 3. Instll the propeller nut. Tighten seurely. 4. Use MotorGuide propeller wrenh or pliers to tighten the propeller nut nother ¼ turn. Gret White Sltwter Models Only Corrosion on the metl omponents of the trolling motor ours when two or more metls tht re dissimilr re brought into eletril ontt underwter. The use of srifiil node uses ll of the other metls on the trolling motor to beome the thodes. The node will orrode nd the trolling motor will not. Mintenne: If exessive orrosion ours, reple the node. Reommended MotorGuide Aessory Desription Srifiil Anode Kit Prt Number MAR00204 33