RC00 SERIES 5, 8, 0, & 5 FLAIL SHREDDER Rev 09-5 Part No. 0077094P PART'S MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Servis-Rhino (800-446-558) to obtain a Free copy before operating the equipment. RHINO 5
TO THE OWNER/OPERATOR/DEALER BEFORE YOU START!!
Parts Section PARTS SECTION
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Servis-Rhino Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: RHINO 00 S. Sangamon Ave. Gibson City, IL 60936 800-446-558 Email: parts@servis-rhino.com 0 Alamo Group Inc. Parts Section
PART NAME INDEX BELT DRIVE - 5 8 0... 4 BELT DRIVE - 5... 7 CASTER ASSEMBLY - 5/8... 9 CASTER ASSEMBLY - 0/5... CUTTING REEL ASSEMBLY - 5 8 0... 3 CUTTING REEL ASSEMBLY - 5... 5 CYLINDER ASSEMBLY... 7 DRIVELINE (NON CV) -3/4 YOKE... 9 DRIVELINE (NON CV) -3/8 YOKE... 0 DRIVELINE CV - 000 RPM 3/4-0 SPL CAT 6 00786845 (CURRENT)... DRIVELINE CV - 000 RPM 3/8- SPL CAT 6 00786844 (CURRENT)... DRIVELINE CV-000 RPM (PULL-TYPE) -3/4-0... 3 DRIVELINE CV-000 RPM (PULL-TYPE) -3/8-0... 5 DRIVETUBE ASSEMBLY... 7 DRIVETUBE ASSEMBLY - 5... 30 END TOW KIT ASSEMBLY - (PULL TYPE)... 3 END TOW KIT ASSEMBLY - (SEMI-MOUNT)... 35 GEARBOX ASSEMBLY - 007649... 38 GENERAL ASSEMBLY... 40 HITCH ASSEMBLY... 4 HYDRAULIC CYLINDER - LIFT KIT OPTION... 43 OPTIONAL DRIVELINE - 00775 - -3/4-0 SPLINE BOTH ENDS,55R L/T (TALLER TIRES)... 45 SAFETY LIGHT KIT ASSEMBLY... 46 SAFTEY LIGHT KIT - END TOW ASSEMBLY... 48 SIGNAL LAMPS -DUAL (AMBER)... 50 SIGNAL LAMPS -DUAL (RED)... 5 TONGUE ASSEMBLY... 5 WHEEL BAR ASSEMBLY... 54 WHEEL HUB ASSEMBLY... 56 WHEEL SPINDLE ASSEMBLY 6-BOLT... 57 0 Alamo Group Inc. Parts Section -3
BELT DRIVE - 5 8 0 0 Alamo Group Inc. Parts Section -4
BELT DRIVE - 5 8 0 Continued... ITEM PART NO. QTY. 0074090 007670 3 0076700 4 0076706 5 363N4C 6 3977H8C 7 00763 4 8 00856 4 9 3608H8C 6 0 554 4 0075073 007694 3 0076698 4 0076688 5 0845500 6 6 0069500 8 7 007509 4 8 0074049 9 0073940 0 0076684 0076687 0000000 0 3 0076705 4 007570 4 5 00348 4 6 470 7 0005800 8 8 0030700 4 9 0074883 4 30 0000700 8 3 0000800 8 3 0075604 33 007679 34 0076709 35 007670 36 0076708 37 0076675 38 0076707 4 39 3864H5C 4 40 0007000 4 4 0004000 4 DESCRIPTION BELT, BANDED SHIELD BELT PLATE, LATCH LATCH SLAM PHLP SCREW PNHD 0-4 X 3/8 TOPLOCK NUT 0-4 GR C PL PIN CLEVIS PIN ROLL BOLT WASHER FLAT KEY BUSHING PULLEY SPACER, DRIVE END BOLT NUT, TOPLOCK KEY BUSHING PULLEY PLATE, RH KNOCK-OUT END PLATE PLATE, LH KNOCK-OUT END PLATE BOLT PLATE, SHIELD KNOCK OUT HOSE COUPLING FITTING, GREASE NUT, TOPLOCK BOLT BOLT FLATWASHER NUT TOPLOCK PLATE, EXTENSION END HOUSING, BEARING DRIVE SEAL RING BEARING HOUSING, BEARING DRIVE STOP, RUBBER BUMPER BOLT LOCKWASHER NUT 0 Alamo Group Inc. Parts Section -5
BELT DRIVE - 5 8 0 Continued... ITEM PART NO. QTY. DESCRIPTION 4 00000 8 FLATWASHER 43 007709 BEARING MOUNT WLDMT 44 007688 CLEVIS YOKE 5/8-8 45 007579 CLEVIS PIN / X -/ 46 00000400 COTTER PIN /8 X -/ 47 007693 ADJUSTER ROD 5/8-8 48 00036300 6 HEX NUT 5/8-8 0 Alamo Group Inc. Parts Section -6
BLANK INTENTIONALLY 0 Alamo Group Inc.
BELT DRIVE - 5 ITEM PART NO. QTY. DESCRIPTION 0074090 BELT, BANDED 007670 SHIELD BELT 3 0076700 PLATE, LATCH 4 0076706 LATCH SLAM 5 095994 8 NUT, TOPLOCK 6 000400 8 BOLT 7 00763 4 PIN CLEVIS 8 00856 4 PIN ROLL 9 3608H8C 6 BOLT 0 554 4 WASHER FLAT 0075073 KEY 007694 BUSHING 3 0076698 PULLEY 4 0076688 SPACER, DRIVE END 0 Alamo Group Inc. Parts Section -7
BELT DRIVE - 5 Continued... ITEM PART NO. QTY. DESCRIPTION 5 0845500 6 BOLT 6 0069500 8 NUT, TOPLOCK 7 007509 4 KEY 8 0074049 BUSHING 9 0073940 PULLEY 0 0076684 PLATE, RH KNOCK-OUT END PLATE 0076687 PLATE, LH KNOCK-OUT END PLATE 0000000 0 BOLT 3 0076705 PLATE, SHIELD KNOCK OUT 4 007570 4 HOSE 5 00348 4 COUPLING 6 470 FITTING, GREASE 7 0005800 8 NUT, TOPLOCK 8 0030700 4 BOLT 9 0074883 4 BOLT 30 0000700 8 FLATWASHER 3 0000800 8 NUT TOPLOCK 3 0075604 PLATE, EXTENSION END 33 007679 HOUSING, BEARING DRIVE 34 0076709 SEAL 35 007670 RING 36 0076708 BEARING 37 0076675 HOUSING, BEARING DRIVE 38 0076707 4 STOP, RUBBER BUMPER 39 3864H5C 4 BOLT 40 0007000 4 LOCKWASHER 4 0004000 4 NUT 4 00000 8 FLATWASHER 43 0076679 PLATE, BEARING ANTI-WRAP 44 007688 CLEVIS YOKE 5/8-8 45 007579 CLEVIS PIN / X -/ 46 00000400 COTTER PIN /8 X -/ 47 007693 ADJUSTER ROD 5/8-8 48 00036300 6 HEX NUT 5/8-8 0 Alamo Group Inc. Parts Section -8
CASTER ASSEMBLY - 5/8-007676 ITEM PART NO. QTY. DESCRIPTION 007657 WELDMENT- AXLE ARM 007655 PLATE CLAMP 3 0075095 4 BOLT 4 0069500 4 NUT 5 06565000 MANUAL LIFT SCREW 6 0076487 WELDMENT- PIVOT BRACKET 7 007674 PIN (LOWER) 8 007677 PIN (UPPER) 9 00758 PIN 0076494 TUBE LOCK 007747 WELDMENT- CASTER SPINDLE 3 400 ROLLER PIN 4 0000800 LOCKNUT TLM / NC PL5 5 00764375 HHCS, / NC X 3.5 PL5 0 00776306 ASY, HUB AND SPINDLE 4 4505 /4-8 SELF TAPPING ZERK 0 Alamo Group Inc. Parts Section -9
CASTER ASSEMBLY - 0/5-007704 ITEM PART NO. QTY. DESCRIPTION 007657 WELDMENT- AXLE ARM 007655 PLATE CLAMP 3 0075095 4 BOLT 4 0069500 4 NUT 5 06565000 MANUAL LIFT SCREW 6 0076487 WELDMENT- PIVOT BRACKET 7 007674 PIN (LOWER) 8 007677 PIN (UPPER) 9 00758 PIN 0 0077035 WDMT, 6-BOLT CASTER 0076494 TUBE LOCK 4505A ASY, HUB AND SPINDLE 3 400 ROLLER PIN 4 0005800 LOCKNUT TLM 3/8-NC PLC 5 00059900 HEXB, 3/8 NC 3 PL5 6 4505 /4-8 SELF TAPPING ZERK 0 Alamo Group Inc. Parts Section -
CUTTING REEL ASSEMBLY - 5 8 0 0 Alamo Group Inc. Parts Section -3
CUTTING REEL ASSEMBLY - 5 8 0 Continued... ITEM PART NO. QTY. DESCRIPTION 007644 CUTTERSHAFT ASSEMBLY - 5` 007645 CUTTERSHAFT ASSEMBLY - 8` 007685 CUTTERSHAFT ASSEMBLY - 0` 00744 64 SHRDER KNIFE - SHRT - 5` 00744 96 SHRDER KNIFE - SHRT- 8` 00744 4 SHRDER KNIFE - SHRT- 0` 3 0074833 4 SHREDDER KNIFE - LONG 4 00705 84 BOLT - 5` 00705 00 BOLT - 8` 00705 08 BOLT- 0` 007596 84 NUT - 5` 007596 00 NUT - 8` 007596 08 NUT- 0` 007470 84 BUSHING - 5` 007470 00 BUSHING- 8` 007470 08 BUSHING - 0` 7 007678 ASY, CENTER BEARING MOUNT 8 0076689 SPACER, SEAL TUBE 9 554 4 WASHER, SPECIAL FLAT 0 007608 SHIELD ANTI-WRAP 00750959 4 BOLT 0000700 8 FLATWASHER / PL STD 3 0000800 4 NUT 4 0075658 4 HEXB 5/8 X -/4 PL5 5 3608H8C - HEXB 5/8 X -/4 GR8 6 0069500 4 NUT 5/8- TOPLOCK 7 0076744 FRNT INNER EXT BAR 8 0076505 FRNT ANGLE EXT BAR - 5` 0076506 4 FRNT ANGLE EXT BAR - 8` 0076499 4 FRNT ANGLE EXT BAR - 0` 0077077 GREASE FITTING STEEL TUBE RH 0077078 GREASE FITTING STEEL TUBE LH 0 0000000 4 HHCS 3/8 NC X 3/4 PL5 00000 4 FLATWASHER STD 3/8 0076799 PLATE, CENTER SHIELD COVER 5 6 9 0 Alamo Group Inc. Parts Section -4
CUTTING REEL ASSEMBLY - 5 ITEM PART NO. QTY. DESCRIPTION 007660 CUTTERSHAFT ASSEMBLY 00744 64 SHREDDER KNIFE - SHORT 3 007470 3 BUSHING 4 00705 3 BOLT 5 007596 3 LOCKNUT 6 0074833 4 SHREDDER KNIFE - LONG 7 0076709 SEAL 8 0076708 BEARING 9 0076680 CENTER BEARING MOUNT 0 007678 CENTER BEARING MOUNT ASSY. (INCLUDES ITEM # 7,8, & 9) 3608H8C 6 BOLT 0069500 6 TOPLOCK NUT 3 0000000 6 BOLT 4 030646 LOCKWASHER 5 000400 3 BOLT 6 095994 3 TOPLOCK NUT 7 0076735 LH GREASE LINE SHIELD 8 0076734 RH GREASE LINE SHIELD 9 0076737 ELBOW HYD. ADAPTER 0 0076738 GREASE LINE 0076736 STRAIGHT HYD. ADAPTER 0 Alamo Group Inc. Parts Section -5
CUTTING REEL ASSEMBLY - 5 Continued... ITEM PART NO. QTY. DESCRIPTION 0075658 4 BOLT 3 554 4 SPECIAL FLATWASHER 4 0076689 SEAL TUBE SPACER 5 007608 ANTI-WRAP SHIELD 6 00750959 4 BOLT 7 0000800 4 TOPLOCK NUT 8 0076799 CENTER SHIELD COVER PLATE 9 00000 6 FLATWASHER 30 0000700 8 FLATWASHER / PL STD 0 Alamo Group Inc. Parts Section -6
CYLINDER ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 00759946A CYLINDER ASSEMBLY 4758 CLEVIS CAP 4757 ROD CAP 3 0077473 PISTON 4 00774737 ROD 5 00774748 TUBE 6 0077474 4 TIE ROD 7 -------- END CAP O-RING 8 -------- ROD WIPER SEAL 9 -------- ROD DUST SEAL 0 -------- PISTON SEAL -------- PISTON WEAR RING -------- BACKUP WASHER 3 30477 NYLON THREAD PROTECTOR 4 9740 ROD CLEVIS 5 00774740 SET SCREW 6 33005H5C 8 TIE ROD NUT 7 5JRC640 PISTON NUT 8 973 PORT PLUG 9 4754 BREATHER PLUG 0077476 CONSISTS OF SEAL KIT 0 Alamo Group Inc. Parts Section -7
DRIVELINE (NON CV) -3/4 YOKE ITEM PART NO. QTY. DESCRIPTION 0074738 KIT-SLIDE COLLAR REPAIR 00756 YOKE SLIDE LOCK -3/4-0 SPL. 3 W507 CROSS & BEARING KIT 5 00780376 NYLON REPAIR KIT 0070407 PTO SHAFT, INNER ASY, INNER HALF DRIVELINE 3 0076939 PTO SHAFT, OUTER ASY, OUTER HALF DRIVELINE 4 0076940 SHIELD COMPLETE 0 Alamo Group Inc. Parts Section -9
DRIVELINE (NON CV) -3/8 YOKE ITEM PART NO. QTY. DESCRIPTION 7680 REPAIR KIT-SAFETY SLIDE LOCK Y 03646 YOKE- 3/8- SPLINE-TRACTOR END 3 W507 CROSS & BEARING KIT 5 00780376 NYLON REPAIR KIT 00756 SLIDE LOCK YOKE-3/4-0 SPL. IMPLAMENT END 00746 ASY, INNER HALF DRIVELINE 3 0076939 ASY, OUTER HALF DRIVELINE 4 0076940 SHIELD COMPLETE 5 0074738 KIT-SLIDE COLLAR REPAIR 0 Alamo Group Inc. Parts Section -0
DRIVELINE CV - 000 RPM 3/4-0 SPL CAT 6 00786845 (CURRENT) ITEM PART NO. QTY. DESCRIPTION 00786848 ASY,CV YOKE - -3/4-0 SPLINE 00786849 KIT,CROSS & BEARING 3 00786850 HOUSING,CV CENTER 4 00756005 DECAL, ROTATING DRIVELINE 5 00756004 DECAL,DANGER - GUARD MISSING 6 00779050 KIT,CROSS & BEARING 7 0077905 YOKE, -3/4-0 SPLINE 8 00779053 BOLT,5/8-X-/ FLANGE SERAT 9 0077955 ASY,GUARD SET 0 Alamo Group Inc. Parts Section -
DRIVELINE CV - 000 RPM 3/8- SPL CAT 6 00786844 (CURRENT) ITEM PART NO. QTY. DESCRIPTION 00786847 ASY,CV YOKE - -3/8- SPLINE 00786849 KIT,CROSS & BEARING 3 00786850 HOUSING,CV CENTER 4 00756005 DECAL, ROTATING DRIVELINE 5 00756004 DECAL,DANGER - GUARD MISSING 6 00779050 KIT,CROSS & BEARING 7 0077905 YOKE, -3/4-0 SPLINE 8 00779053 BOLT,5/8-X-/ FLANGE SERAT 9 0077955 ASY,GUARD SET 0 Alamo Group Inc. Parts Section -
BLANK INTENTIONALLY 0 Alamo Group Inc.
DRIVELINE CV-000 RPM (PULL-TYPE) -3/4-0 0 Alamo Group Inc. Parts Section -3
DRIVELINE CV-000 RPM (PULL-TYPE) -3/4-0 ITEM PART NO. QTY. 00763554 0076434 848 3 838 4 743 5 8484 6 8384 7 00763557 8 00763558 9 8489 0 0077407 00760636 8486 8393 3 00763560 4 00763559 5 740 6 8949 7 46438 8 8 8974 9 00759556 0 0077408 00759556 0075670 00763555 3 00763556 DESCRIPTION D/L CV -3/4-0 SPL (0DB) YOKE-CV QD- 3/4-0 SPLINE- DOUBLE YOKE FITTING,GREASE M8 X YOKE-INBOARD CROSS & BEARING KIT SPRING PIN 0MM X 90MM PROFILE, STAR INNER PROFILE,STAR OUTER INBOARD YOKE YOKE -3/4-0 SPLINE YOKE -3/4-0 SPLINE A.S. CROSS & BEARING KIT BEARING RING TUBE,OUTER SHIELD TUBE,D/L INNER SHIELD ASSY-BEARING & CV CONE SHIELD CONE SCREW-SC5 SUPPORT BEARING KIT, SLIDE COLLAR LOCK ASY CC YOKE KIT, SLIDE COLLAR GREASE FITTING /4-8 BOLT THD D/L TRACTOR HALF -3/4-0 CV D/ L IMPLEMENT HALF -3/4-0 0 Alamo Group Inc. Parts Section -4
DRIVELINE CV-000 RPM (PULL-TYPE) -3/8-0 0 Alamo Group Inc. Parts Section -5
DRIVELINE CV-000 RPM (PULL-TYPE) -3/8-0 ITEM PART NO. QTY. 00760453 8478 848 3 838 4 743 5 8484 6 8384 7 0076063 8 00760634 9 8489 0 0077407 00760636 8486 8393 3 00760640 4 0076064 5 740 6 8949 7 46438 8 8 8974 9 839 0 0077408 00759556 0075670 DESCRIPTION DRIVELINE,000 CV CAT5-3/8- YOKE -3/8 -SP DOUBLE YOKE FITTING,GREASE M8 X YOKE-INBOARD CROSS & BEARING KIT SPRING PIN 0MM X 90MM PROFILE-INNER SAGA PROFILE & SLEEVE W.A. INBOARD YOKE YOKE -3/4-0 SPLINE YOKE -3/4-0 SPLINE A.S. CROSS & BEARING KIT BEARING RING TUBE, OUTER SHIELD OVL TUBE,INNER SHIELD ROUND ASSY-BEARING & CV CONE SHIELD CONE SCREW-SC5 SUPPORT BEARING Q.D. COLLAR KIT LOCK ASY CC YOKE KIT, SLIDE COLLAR GREASE FITTING /4-8 BOLT THD 0 Alamo Group Inc. Parts Section -6
DRIVETUBE ASSEMBLY 0 Alamo Group Inc. Parts Section -7
DRIVETUBE ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 0075688 DRIVE TUBE RIGHT HAND- 5 007578 DRIVE TUBE RIGHT HAND- 8 0075687 DRIVE TUBE RIGHT HAND- 0 007569 DRIVE TUBE LEFT HAND- 5 0075633 DRIVE TUBE LEFT HAND- 8 0075686 DRIVE TUBE LEFT HAND- 0 0074774 PULLEY SHAFT- 5 0075634 PULLEY SHAFT- 8 007437 PULLEY SHAFT- 0 007473 4 FLANGE BEARING 3 0075678 RH DRIVE TUBE WELDMENT- 5 0075689 RH DRIVE TUBE WELDMENT- 8 007568 RH DRIVE TUBE WELDMENT- 0 0075680 LH DRIVE TUBE WELDMENT- 5 0075690 LH DRIVE TUBE WELDMENT- 8 007568 LH DRIVE TUBE WELDMENT- 0 4 0075509 DRIVELINE 4A 007599 DRIVELINE TUBE WELDMENT 5 007700 TOP DRIVE SHIELD-RH - 0` 007700 TOP DRIVE SHIELD-LH -0 6 0000800 0 NUT 8 0003300 8 HEX BOLT 007590 SHIM 0076508 YOKE CLAMP -/" ROUND 3 0070409 YOKE -3/8" SPLINE 4 76465 4 CROSS & BEARING KIT 5 0075964 4 LOCK COLLAR 6 007566 PIVOT EAR WELDMENT- RH 0075663 PIVOT EAR WELDMENT- LEFT HAND 8 7AH0 4 BOLT 9 0003700 4 NUT 00763 4 CLEVIS PIN 5 8` 00000400 4 COTTER PIN 5 8` 3 00769933 6 PLASTIC KNOB 5 8 4 007509 4 KEY 5 007570 HOSE GREASE FITTING 6 00348 COUPLING 7 00003500 GREASE FITTING 8 7A83 BOLT 9 007668 ASY,HINGED SHIELD COVER 30 363N4C 8 PHLP SCRW PN HD 0-4 X 3/8 0 Alamo Group Inc. Parts Section -8
DRIVETUBE ASSEMBLY Continued... ITEM PART NO. QTY. 3 3977H8C 8 3 000400 4 33 030646 4 34 00000 8 35 000640 4 36 0076587 37 007665 38 007666 39 007667 DESCRIPTION TOPLOCK NUT 0-4 GR C PL HHCS 3/8 NC PL5 LOCKWASHER,3/8,MEDIUM-ZP FLATWASHER 3/8 PL STD LOCKNUT CLM 3/8 NC PLB COVER,HINGED SHIELD HINGE,3 SECTION STUD,SPHERICAL M6 X 36MM KNOB,PLASTIC NUT M6 X X MM 0 Alamo Group Inc. Parts Section -9
BLANK INTENTIONALLY 0 Alamo Group Inc.
DRIVETUBE ASSEMBLY - 5 0 Alamo Group Inc. Parts Section -30
DRIVETUBE ASSEMBLY - 5 Continued... ITEM PART NO. QTY. 0076697 007473 4 3 0076695 0076699 4 0076493 4A 007663 5A 007660 5B 007660 6 0000800 0 8 0003300 8 007590 007664 3 00766 4 8388 4 5 0075964 4 6 007566 0075663 8 0880900 4 9 0003700 4 000400 6 030646 6 3 00000 8 4 007509 4 5 007570 6 00348 7 470 8 7A83 9 4505 30 007668 4 3 363N4C 8 3 3977H8C 8 33 000640 6 34 0076587 35 007665 36 007666 37 007667 DESCRIPTION PULLEY SHAFT FLANGE BEARING RIGHT HAND DRIVE TUBE LEFT HAND DRIVE TUBE DRIVELINE DRIVELINE TUBE TOP DRIVE SHIELD, RH TOP DRIVE SHIELD, LH NUT BOLT SHIM YOKE CLAMP -3/8" ROUND YOKE -3/8" SPLINE CROSS & BEARING KIT LOCK COLLAR PIVOT EAR, RH (SHOWN) PIVOT EAR, LH BOLT NUT BOLT LOCKWASHER FLATWASHER KEY GREASE FITTING HOSE COUPLING GREASE FITTING BOLT FITTING, GREASE HINGE SHIELD COVER ASSY. SCREW TOPLOCK NUT 0-4 GR C PL LOCKNUT COVER,HINGED SHIELD HINGE,3 SECTION STUD,SPHERICAL M6 X 36MM KNOB,PLASTIC NUT M6 X X MM 0 Alamo Group Inc. Parts Section -3
END TOW KIT ASSEMBLY - (PULL TYPE) 0 Alamo Group Inc. Parts Section -3
END TOW KIT ASSEMBLY - (PULL TYPE) Continued... ITEM PART NO. QTY. DESCRIPTION 0077097 WDMT,TOW HITCH 00554600 RATCHET JACK 3 0076539 PLATE,TONGUE LIFT 4 0075708 4 SNAPPER PIN 5 3908C HEX LOCKNUT 3/4-0 6 000070 FLAT WASHER 7 0075698 4 WLDMT, PIN TOW HITCH 8 005700 HEXB 3/4 NC 6 PL5 9 00757908 CHAIN, SAFETY TOW 0 0076768 ASY,MOUNTED STUBBLE GUARD TIRE 057603 WHEEL 6 X 5-6 BOLT A 0076784 TIRE,STUBBLE GUARD 9.5L X 5- B TR45 VALVE STEM 3 0076349 BOLT- WHEEL /-0UNF- LG 4 0957009 HHCS 3/8 NC 3-/ PL5 5 0076538 WDMT,WHEEL ARM 6 007679 ADP HYD TEE 6MJ - 6MJ - 6MJ 7 0005800 NUT TOPLOCK 8 00580 HOSE 9 0076790 HOSE #6-6FJX - 6FJX - 83 LG 0 007446 FLATWASHER, SPINDLE 4659 SPINDLE, DIA X 9.66 W/HOLE 680 SEAL-.875 ID X 3.005 OD X.5 3 0536005 BEARING CONE.65 ID 4 0536004 BEARING CUP 5 0535506 ASY,HUB & CUP SUB-,6-BOLT 6 053600 BEARING CUP.38 OD 7 0536003 BEARING CONE.50 ID 8 0075553 PIN-COTTER 3/6 X -/ PLATED 9 33099C HEX SLOTTED NUT 7/8-4 30 0075649 DUST CAP 3 4505A ASY,HUB & SPINDLE 3 007678 WDMT,AXLE PIVOT PIN 33 45703 CYLINDER,HYDRAULIC 3 X 0 33A 304704 PIN, 33B 490 HAIRPIN CLIP 7/8 34 007675 PIN,FRONT CYLINDER MOUNT 35 0076778 STOP,CYLINDER 36 0076776 WDMT,AXLE LOCK PIN 37 00758 PIN-SPIRAL 3/8 X -/ 38 4908 HAIRPN COT..78 X 3 9/6 0 Alamo Group Inc. Parts Section -33
END TOW KIT ASSEMBLY - (PULL TYPE) Continued... ITEM PART NO. QTY. DESCRIPTION 39 000400 BOLT 40 4949 PIN,CLEVIS 7/6 X -/4 PLT 4 4907 HAIR PIN COTTER.0 X -/ 4 0300588 3 ADAPTER, HYD, ELBOW 43 3403H5C HEX CAP /-3 X 3/4 GR.5 44 0000300 LOCKWASHER 45 0076533 PIN,TONGUE LIFT 46 007679 HOSE #6-8MP - 6FJX - 9 LG 47 46863 JACK,AG 7000# CAP.,SIDE WIND 48 0074989 PIN-JACK RETAINING 49 93756 SPEC. 90DG ELBOW W/RESTRICTOR 50 00EH PIPE NIPPLE 3/8 X CLOSE 5 43735 BALL VALVE, 3/8 NPTF 5 458383 DECAL,WARNING,TOWING SPEED 53 096764 DECAL - PINCH POINTS 54 0076878 WDMT,END TOW ARM 55 0076897 WDMT,END TOW MOUNT 57 400 ROLL PIN 3/8 X 3/4 58 0076494 TUBE,LOCK CASTER WHEEL 59 3707B3 CLIP-X HAIR PIN 60 0076875 WDMT,INDEX PIN 6 00758 4 PIN-SPIRAL 3/8 X -/ 6 007674 4 PIN-CASTER 63 007690 WDMT,SPINDLE MOUNT 64 0076906 WDMT,UPPER END TOW ARM 65 0076908 WDMT,END TOW REAR MOUNT 66 0075975A CYLINDER HYD 3 X 5-/ 67 0076895 STOP,CYLINDER 68 007688 PLATE,MOUNT WIDE 69 0963646 4 HHCS 3/4 NC -/ PL8 70 0003700 4 NUT, TOPLOCK 7 0076988 WDMT, FRONT STRUT PIVOT 7 0076994 WDMT, FRONT CYLINDER MOUNT 73 0958757 4 HHCS 3/4 NC 7 PL8 0 Alamo Group Inc. Parts Section -34
BLANK INTENTIONALLY 0 Alamo Group Inc.
END TOW KIT ASSEMBLY - (SEMI-MOUNT) 0 Alamo Group Inc. Parts Section -35
END TOW KIT ASSEMBLY - (SEMI-MOUNT) Continued... ITEM PART NO. QTY. DESCRIPTION 0076559 WDMT,TOW HITCH 4 0075708 SNAPPER PIN 5 3908C HEX LOCKNUT 3/4-0 6 000070 FLAT WASHER 7 0075698 WLDMT, PIN TOW HITCH 8 005700 HEXB3/4 NC 6 PL5 9 00757908 CHAIN, SAFETY TOW 0 0076768 ASY,MOUNTED STUBBLE GUARD TIRE 057603 WHEEL 6 X 5-6 BOLT A 0076784 TIRE,STUBBLE GUARD 9.5L X 5- B TR45 VALVE STEM 3 0076349 BOLT- WHEEL /-0UNF- LG 4 0957009 HHCS 3/8 NC 3-/ PL5 5 0076538 WDMT,WHEEL ARM 6 007679 ADP HYD TEE 6MJ - 6MJ - 6MJ 7 0005800 NUT TOPLOCK 8 00580 HOSE 9 0076790 HOSE #6-6FJX - 6FJX - 83 LG 0 007446 FLATWASHER, SPINDLE 4659 SPINDLE, DIA X 9.66 W/HOLE 680 SEAL-.875 ID X 3.005 OD X.5 3 0536005 BEARING CONE.65 ID 4 0566004 BEARING CUP 5 0535506 ASY,HUB & CUP SUB-,6-BOLT 6 053600 BEARING CUP.38 OD 7 0536003 BEARING CONE.50 ID 8 0075553 PIN-COTTER 3/6 X -/ PLATED 9 33099C HEX SLOTTED NUT 7/8-4 30 0075649 DUST CAP 3 4505A ASY,HUB & SPINDLE 3 007678 WDMT,AXLE PIVOT PIN 33 45703 CYLINDER,HYDRAULIC 3 X 0 33A 304704 PIN, 33B 490 HAIRPIN CLIP 7/8 34 007675 PIN,FRONT CYLINDER MOUNT 35 0076778 STOP,CYLINDER 36 0076776 WDMT,AXLE LOCK PIN 37 00758 PIN-SPIRAL 3/8 X -/ 38 4908 HAIRPN COT..78 X 3 9/6 39 000400 BOLT 40 4949 PIN,CLEVIS 7/6 X -/4 PLT 0 Alamo Group Inc. Parts Section -36
END TOW KIT ASSEMBLY - (SEMI-MOUNT) Continued... ITEM PART NO. QTY. DESCRIPTION 4 4907 HAIR PIN COTTER.0 X -/ 4 0300588 3 ADAPTER, HYD, ELBOW 46 007679 HOSE #6-8MP - 6FJX - 9 LG 47 0076730 JACK,AG 5000# CAP.,SIDE WIND 48 0074989 PIN-JACK RETAINING 49 93756 SPEC. 90DG ELBOW W/RESTRICTOR 50 00EH PIPE NIPPLE 3/8 X CLOSE 5 43735 BALL VALVE, 3/8 NPTF 5 458383 DECAL,WARNING,TOWING SPEED 53 096764 DECAL - PINCH POINTS 54 007687 WDMT,CASTER WHEEL 55 470 GREASE FITTING /8 SELF TAP 56 00758 5 PIN-SPIRAL 3/8 X -/ 57 007677 3 PIN CASTER ASY. 58 400 ROLL PIN 3/8 X 3/4 59 0076494 TUBE,LOCK CASTER WHEEL 60 007674 PIN CASTER ASY. LOWER 6 3707B3 CLIP-X HAIR PIN 6 0076875 WDMT,INDEX PIN 63 06565000 MANUAL-LIFT SCREW 64 0075975A CYLINDER HYD 3 X 5-/ 65 0076878 WDMT,END TOW ARM 66 007688 WDMT,CASTER END TOW MOUNT 67 0076886 WDMT,REAR CASTER MOUNT 68 0076895 STOP,CYLINDER 69 007688 PLATE,MOUNT WIDE 70 0963646 4 HHCS 3/4 NC -/ PL8 7 0003700 4 NUT, TOPLOCK 7 0076988 WDMT, FRONT STRUT PIVOT 73 0076994 WDMT, FRONT CYLINDER MOUNT 74 0958757 4 HHCS 3/4 NC 7 PL8 0 Alamo Group Inc. Parts Section -37
BLANK INTENTIONALLY 0 Alamo Group Inc.
GEARBOX ASSEMBLY - 007649 ITEM PART NO. QTY. DESCRIPTION 007669 HOUSING 0076630 CAP INPUT 3 007663 CAP OUTPUT 4 007663 PINION GEAR 5 0076633 GEAR 6 0076634 SHAFT INPUT 7 0076635 SHAFT CROSS 8 0076636 BEARING CUP 0 Alamo Group Inc. Parts Section -38
GEARBOX ASSEMBLY - 007649 Continued... ITEM PART NO. QTY. DESCRIPTION 9 0076637 BEARING CONE 0 0076638 BEARING CUP 0076639 BEARING CONE 0076640 BEARING CUP 3 007664 BEARING CONE 4 0076645 SEAL INPUT 5 0076646 SEAL,CROSS 6 0076647 GASKET 0.MM 7 0076648 GASKET 0.MM 8 0076649 GASKET 0.5MM 9 0076650 SPACER 0 70499 COTTER PIN 3306H5C 4 BOLT 007665 NUT,HEX SLOTTED 3 00000 4 LOCKWASHER 4 00753630 PLUG PIPE, HEAD "(NOT SHOWN) 5 303 PLUG PIPE, HEAD 8"(NOT SHOWN) 6 007665 PLUG RELIEF W/DIPSTICK (NOT SHOWN) 7 ------------- I.D. TAG (NOT SHOWN) 8 0076653 RETAINING RING (NOT SHOWN) 0 Alamo Group Inc. Parts Section -39
GENERAL ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 0 Alamo Group Inc. Parts Section -40
GENERAL ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 0076383 TONGUE (CV OPTION ONLY) TONGUE 007638 ASSEMBLY (TONGUE, JACK & CHAIN) 0075593 HITCH ASSEMBLY 3 0076793 GEAR BOX 4 00764 WHEEL BAR ASSEMBLY- 5 00764 WHEEL BAR ASSEMBLY- 8 007643 WHEEL BAR ASSEMBLY- 0 6 007569 DRIVE TUBE ASSEMBLY LEFT HAND- 5 0075633 DRIVE TUBE ASSEMBLY LEFT HAND- 8 0075686 DRIVE TUBE ASSEMBLY LEFT HAND- 0 7 0075688 DRIVE TUBE ASSEMBLY RIGHT HAND- 5 007578 DRIVE TUBE ASSEMBLY RIGHT HAND- 8 0075687 DRIVE TUBE ASSEMBLY RIGHT HAND- 0 8 00759946A HYDRAULIC CYLINDER 9 007639 WLDMT-CYLINDER PIN 0 0075756 ASSY- AXLE ARM WITH CLAMP PLATES 0075588 ASSY- LINK BAR TOP (3 POINT MOUNT ONLY) 0075595 ASSY- JACK STAND (3 POINT MOUNT ONLY) 3 0075675 RUBBER FLAP 5 0075677 RUBBER FLAP 8 007703 RUBBER FLAP 0 3A 00770 GUARD FRONT FLAP CENTER -5 HOLE 3B 007707 GUARD FRONT FLAP RH -4 HOLE 4 0075667 OUTER RETAINING STRAP 5 0075667 OUTER RETAINING STRAP 8 0075667 RETAINING STRAP 0 4A 007703 RETAINING STRAP 0 RH INNER -3 HOLE 4B 00770 RETAINING STRAP 0 RH CENTER -5 HOLE 4C 007704 RETAINING STRAP 0 RH OUTER -4 HOLE 4D 007705 RETAINING STRAP 5/8/0 LH OUTER -5 HOLE 5 0075664 INNER RETAINING STRAP 5 0075665 INNER RETAINING STRAP 8 6 00757 PIN 7 0075604 END PLATE EXTENSION WELDMENT 8 007700 TOP DRIVE SHIELD -RH 007700 TOP DRIVE SHIELD -LH 9 00008300 4 BOLT 0 007335 4 LOCKWASHER 6D907 - FLANGE LOCKNUT, 3/8 NC 0 Alamo Group Inc. Parts Section -4
HITCH ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 0075588 LINK BAR TOP ASSY (INCL. # - #8) 0000300 LOCK WASHER 007598 TOP PIN MOWER MOUNT 3 0069500 NUT, TOPLOCK 4 0073550 LINK BAR TOP 5 007388 END WASHER MOUNT PIN 6 007563 PLATE LOCK TOP LINK 7 0074883 HEX BOLT 8 0075508 HEX BOLT 0075593 HITCH ASSY (INCL #9 - #4) 9 0070496 HITCH ASSY WELDMENT 0 007385 TOP LINK PIN 0075547 LOWER PIN 0075548 LOWER HITCH PIN 3 0075704 HITCH MOUNT PIN 4 0075708 6 SNAPPER PIN 0 Alamo Group Inc. Parts Section -4
BLANK INTENTIONALLY 0 Alamo Group Inc.
HYDRAULIC CYLINDER - LIFT KIT OPTION 0 Alamo Group Inc. Parts Section -43
HYDRAULIC CYLINDER - LIFT KIT OPTION Continued... ITEM PART NO. QTY. DESCRIPTION 0000400 FLATWASHER 00606000 COTTER PIN 3 0075534 CONTROL SPACER 4 00759946A CYLINDER 5 00774574 HYD ELBOW ADAPTER 6 0675800 BOLT 7 0965484 HOSE BRKT, SPRING BASE 8 0076800 HYDRAULIC HOSE 9 8354 CYLINDER PIN 0 Alamo Group Inc. Parts Section -44
OPTIONAL DRIVELINE - 00775 - -3/4-0 SPLINE BOTH ENDS,55R L/T (TALLER TIRES) ITEM PART NO. QTY. DESCRIPTION 00784046 COMPLETE GUARD SET 0074738 SSL/AUTO - LOK REPAIR KIT 00756 SLIDE LOCK YOKE ASSY. 3 00779030 BEARING & CROSS KIT 4 00784049 YOKE & SHAFT.59-0 SPLINE 6 00780376 GUARD REPAIR KIT 7 00756005 SAFETY DECAL 8 00756004 SAFETY DECAL 0 00784050 YOKE, TUBE, & SLIP SLEEVE 0 Alamo Group Inc. Parts Section -45
BLANK INTENTIONALLY 0 Alamo Group Inc.
SAFETY LIGHT KIT ASSEMBLY 0 Alamo Group Inc. Parts Section -46
SAFETY LIGHT KIT ASSEMBLY Continued... ITEM PART NO. QTY. 0076955 0076954 3 0005800 4 8 458398 4 9 45839 4 0 00000 4 0076957 0076956 3 0076964 4 467903 5 0076963 6 007696 7 363N3C 4 8 3977H8C 4 9 0075364 4 0 600343 0 03869 8 0058000 6 3 095994 6 4 0300347 5 000400 6 4386 8 390C DESCRIPTION BRACKET, LIGHT RH BRACKET, LIGHT LH NUT,TOPLOCK 3/8NC PLB DECAL,ORANGE REFLECTOR DECAL,RED REFLECTOR FLATWASHER 3/8 PL STD SIGNAL LAMP, RED/BLACK SIGNAL LAMP, AMB/AMB HARNESS, MAIN WIRING - 0 HOLDER,7-WAY CONNECTOR PLUG AG HARNESS, WISHBONE 0 AG HARNESS, EXTENSION 0 PHLP SCRW PN HD 0-4 X /4 TOPLOCK NUT 0-4 GR C PL HHCS,3/8NC X -/4,ZP,GRD5 SUPPORT CLAMP,.500 ID X.406 TY RAP,.30 WIDE X 3 LONG HHCS /4 NC PL5 NUT TOPLOCK /4 NC PLB EMBLEM, SMV HEXB /4 NC 3/4 PL5 SPADE BRACKET,SMV MOUNTING HEX LOCKNUT /4-0 0 Alamo Group Inc. Parts Section -47
SAFTEY LIGHT KIT - END TOW ASSEMBLY 0 Alamo Group Inc. Parts Section -48
SAFTEY LIGHT KIT - END TOW ASSEMBLY Continued... ITEM PART NO. QTY. 0076966 3 0076955 4 0076954 5 467903 6 03869 4 8 4386 9 0300347 0076957 0076956 3 0076965 5 0076963 6 363N3C 4 7 3977H8C 4 9 000400 8 0 00000 8 0005800 8 00750959 3 3 0000700 3 4 0000800 3 5 0058000 6 6 095994 6 30 45839 4 3 458398 4 33 000400 34 390C DESCRIPTION WDMT, LIGHT BRACKET BRACKET, LIGHT -RH BRACKET, LIGHT -LH HOLDER,7-WAY CONNECTOR PLUG TY RAP,.30 WIDE X 3 LONG SPADE BRACKET,SMV MOUNTING EMBLEM, SMV AG LIGHT, SINGLE -RED/BLACK AG LIGHT, SINGLE -AMBER/AMBER HARNESS, MAIN WIRING -35 HARNESS, WISHBONE -0 PHLP SCRW PN HD 0-4 X /4 TOPLOCK NUT 0-4 GR C PL HHCS 3/8 NC PL5 FLATWASHER 3/8 PL STD NUT,TOPLOCK 3/8NC PLB HEXB,/NC X,ZP,GRD5 FLATWASHER / PL STD LOCKNUT TLM / NC PLB HHCS /4 NC PL5 NUT TOPLOCK /4 NC PLB DECAL,RED REFLECTOR DECAL,ORANGE REFLECTOR HEXB /4 NC 3/4 PL5 HEX LOCKNUT /4-0 0 Alamo Group Inc. Parts Section -49
SIGNAL LAMPS -DUAL (AMBER) ITEM PART NO. QTY. DESCRIPTION 47900 LENS,AMBER LAMP 4798 BULB,LIGHT 3 086800 NUT / NF HEX 4 3305C HEX JAM NUT /-0 5 37003C INT TOOTH LOCKWASHER / 6 47903 ASY,8 GROUND WIRE 0 Alamo Group Inc. Parts Section -50
SIGNAL LAMPS -DUAL (RED) ITEM PART NO. QTY. DESCRIPTION 4790 LENS,RED LAMP 4790 LENS,BLACK BLANK LAMP 3 4790 RETAINING RING 4 086800 NUT / NF HEX 5 3305C HEX JAM NUT /-0 6 37003C INT TOOTH LOCKWASHER / 7 47903 ASY,8 GROUND WIRE 0 Alamo Group Inc. Parts Section -5
TONGUE ASSEMBLY 0 Alamo Group Inc. Parts Section -5
TONGUE ASSEMBLY ITEM PART NO. QTY. 0076383 0075548 3 0075698 4 0075708 4 5 0076589 6 0075684 4 7 000700 4 8 0076588 9 0076599 0 007668 363N4C 8 3977H8C 8 3 00757908 4 0076730 5 0076793 6 007665 7 0076587 8 007665 9 007666 0 007667 * 007668 DESCRIPTION TONGUE HITCH LOWER HITCH PIN UPPER HITCH PIN SNAPPER PIN REINFORCEMENT CONE PLATE BOLT LOCKWASHER CLUTCH SAFETY SHIELD GEARBOX SHIELD HINGE SHIELD COVER ASSY. SCREW TOPLOCK NUT 0-4 GR C PL SAFETY TOW CHAIN SIDE WIND JACK GEARBOX ASSEMBLY BREATHER/DIPSTICK COVER HINGE STUD KNOB PARTS INCLUDED IN SHIELD COVER ASY. 0 Alamo Group Inc. Parts Section -53
WHEEL BAR ASSEMBLY 0 Alamo Group Inc. Parts Section -54
WHEEL BAR ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 00764 WHEEL BAR- 5 00764 WHEEL BAR- 8 007643 WHEEL BAR- 0 0075757 4 WHEEL SPINDLE WELDMENT 3 0075758 4 MOUNTING BRACKET PLATE 4 0958883 6 HEX BOLT 6 0000000 6 NUT 9 007639 CYLINDER PIN 0 0075708 SNAPPER PIN NFS 4 5" TIRE (NOT SUPPLIED) 007053 OUTER WHEEL BRACKET WELDMENT 3 00008700 4 5" WHEEL (RIM ONLY) 4 0075064 6 LUG NUT 5 0030700 BOLT 6 0009600 LOCKWASHER 7 000000 NUT 8 093300 8 BOLT 9 0000390 8 LOCKWASHER 0 Alamo Group Inc. Parts Section -55
WHEEL HUB ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 00776306 ASY, HUB AND SPINDLE 0077858 AXLE SPINDLE BOLT IN 000600 PIN-COTTER 5/3 X -/ 3 095749 BEARING CONE 437A 4 5B400 WASHER 7/8 SAE P 5 3747G CAP,HUB 6 00779390 HUB CAP RETAINER 7 3747J NUT, 7/8-4 UNF STD SLOTTED 8 0077873 SEAL KIT 9 00003500 ZERK FITTING /8 STRAIGHT 0 0077875 BEARING CONE (INSIDE) 0075064 5 NUT /-0NF 90DEG.CONE LUG PL 0078594 KIT,WHEEL HUB BEARING (NOT SHOWN) 0 Alamo Group Inc. Parts Section -56
WHEEL SPINDLE ASSEMBLY 6-BOLT ITEM PART NO. QTY. DESCRIPTION 00769 WHEEL SPINDLE LH 007690 WHEEL SPINDLE RH 4659 SPINDLE 053600 BEARING CUP (OUTER) 3 0536003 BEARING CONE (OUTER) 4 0536004 BEARING CUP (INNER) 5 0076349 6 BOLT, WHEEL 7 33099C NUT, SPINDLE 8 680 SEAL, GREASE 9 007446 WASHER 0 0075649 DUST CAP 0075553 COTTER PIN 3 0535506 ASSY HUB W/CUPS 4 0536005 BEARING CONE (INNER) 5 4505A ASSY, HUB & SPINDLE 6 0957009 BOLT 7 007694 SPINDLE MOUNT AXLE 8 007674 PLATE, CLAMP 9 0963646 4 BOLT 0 0003700 4 NUT, TOPLOCK 0005800 NUT, TOPLOCK 0 Alamo Group Inc. Parts Section -57
LIMITED WARRANTY. LIMITED WARRANTIES.0.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( Purchaser ) and warrants for six months to the original commercial or industrial purchaser ( Purchaser ) that the goods purchased are free from defects in material or workmanship..0.manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship..03.this limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator s Manual..04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer.. REMEDIES AND PROCEDURES..0.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase..0.purchaser claims must be made in writing to the Authorized Dealer ( Dealer ) from whom Purchaser purchased the goods or an approved Authorized Dealer ( Dealer ) within 30 days after Purchaser learns of the facts on which the claim is based..03.purchaser is responsible for returning the goods in question to the Dealer..04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) (b) Repair or replace the defective goods or part(s) or Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer..05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY. 3.0.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3.0.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS. 3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS. 3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO () YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4. MISCELLANEOUS. 4.0.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas. 4.0.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term. 4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein. 4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS SERVIS-RHINO ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Servis-Rhino Implement Model Serial Number Date Purchased Dealer ATTENTION: READ YOUR OPERATOR'S MANUAL RHINO 00 S. Sangamon Ave. Gibson City, IL 60936 800-446-558 Email: parts@servis-rhino.com R
TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (98.5 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER:. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and 3. Ensure that each employee uses such Seatbelt while the tractor is moving; and 4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR. Securely fasten seatbelt if the tractor has a ROPS.. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going - especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly - no jerky turns, starts, or stops. 8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available.
RC5/8/0/5 Printed U.S.A. Part No. 0077094P