install guide Document number 5 Revision Date 08 firmware OEM-AL(RS)-FM6-[ADS-ALCA] hardware ADS-ALCA accessories ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
Page of DOC.: #5 08 vehicle List - of FEATURES MODEL YEAR DATA IMMOBILIZER BYPASS TACHOMETER STATUS HOOD STATUS OUTPUT BRAKE PEDAL STATUS OUTPUT RAP SHUTDOWN CTRL HEATED MIRRORS CTRL HEATED SEATS CTRL REAR DEFROST CTRL A/M RS CTRL FROM OEM REMOTES NOTES Fusion STD key AT - Fusion Hybrid STD key AT - Fusion PTS AT - Fusion Hybrid PTS AT - MKZ PTS AT - MKZ Hybrid PTS AT - I This firmware does not cover the doorlock feature. Use the OEM remote or an aftermarket one button remote to control the doorlock feature. The OEM remotes remain functional during runtime. LINCOLN FORD Automotive Data Solutions Inc. INSTALL TYPE MAKE II The maximum runtime for all models is 0 minutes. The remote start sequence can only be done once. To perform another remote start sequence, start and stop the vehicle or wait hour.
Page of DOC.: #5 08 BOX CONTENTS - OF BOX CONTENTS WHITE WHITE PIN BLACK CONNECTOR 6 PIN WHITE CONNECTOR MODULE 5 6 5 6 7 WHITE BLUE PROGRAMMING BUTTON 0 PIN BLACK CONNECTOR 7 PIN WHITE CONNECTOR LED A B F C E D 0 9 8 7 6 5 BLACK PIN WHITE CONNECTOR DATA CABLE PIN BLUE CONNECTOR DATA CABLE BLACK DATA PORT (WEBLINK, RF, TELEMATIC) WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc.
Page of DOC.: #5 08 Automotive Data Solutions Inc. COMPONENT LOCATOR 0 Blue module, driver side dash 9 White module, driver side dash CanH Gray/Orange module, driver side dash CanL Purple/Orange module, driver side dash V White/Red (+) module, driver side dash Ground /Gray (-) module, driver side dash CanH 0 Blue module, driver side dash CanL 9 White module, driver side dash CanH Gray/Orange module, driver side dash CanL Purple/Orange module, driver side dash V White/Red (+) module, driver side dash Ground /Gray (-) module, driver side dash CanH 0 Blue module, driver side dash CanL 9 White module, driver side dash CanH Gray/Orange module, driver side dash CanL Purple/Orange module, driver side dash V White/Red (+) module, driver side dash Ground /Gray (-) module, driver side dash WIRE COLOR CanH CanL CONNECTOR NAME MODULE LOCATION WIRE DESCRIPTION POLARITY - POSITION MKZ / MKZ Hybrid PTS AT - CONNECTOR TYPE LINCOLN Fusion / Fusion Hybrid PTS AT CONNECTOR COLOR - FORD Fusion / Fusion Hybrid STD key AT YEAR MODEL MAKE TYPE - WIRE CHART - OF
Page 5 of DOC.: #5 08 TYPE - WIRING DIAGRAM - OF MODULE MODULE, DRIVER SIDE DASH A B F STEP C E DATA D A B 5 6 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 0 GREEN/RED (NC) BLUE/YELLOW (NC) 06 BLUE/RED (NC) 5 6 7 PINK (NC) 0 PINK/BLACK (NC) 0 ORANGE (NC) 0 ORANGE/WHITE (NC) ORANGE/BLACK (NC) 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) WHITE (NC) 0 WHITE/RED (NC) 0 WHITE/BLACK (NC) C D CONNECT TEMPORARILY SEE PROGRAMMING PROCEDURE CANL - 9 CANH - 0 STEP CONNECT TO VEHICLE SEE PROGRAMMING PROCEDURE CANL - CANH - BLACK STEP 0 9 8 7 6 5 0 9 8 7 6 5 SELECT ONE OF THE TWO OPTIONS E 0 0 0 BLUE/WHITE (NC) WHITE (NC) BLACK - GROUND RED - V (+) WITHOUT A COMPATIBLE ESSORY: CONNECT V AND GROUND FROM MODULE TO VEHICLE. OR F 5 6 7 8 9 0 DATA CABLE GROUND V (+) GROUND (-) - V (+) - WITH A COMPATIBLE ESSORY: SEE THE COMPATIBLE ESSORIES PAGE FOR DETAILS. GREEN/BLACK (NC) 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) Automotive Data Solutions Inc.
MODULE PROGRAMMING PROCEDURE - OF CONNECT every wire shown in STEP and STEP of the wiring diagram. 07 Page 6 of DOC.: #5 08 Set ignition to ON position. ON 0 Set ignition to ON position. 08 Wait, LED will turn solid RED. 09 ON Wait, LED will turn solid GREEN for seconds. 0 Set ignition to position. ON 0 Set ignition to position. ON 0 Module Programming Procedure completed. Wait, LED will flash GREEN rapidly. 06 DISCONNECT every wire shown in STEP and CONNECT every wire shown in STEP of the wiring diagram. Automotive Data Solutions Inc.
VALET MODE PROGRAMMING PROCEDURE - OF NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Time restriction. Complete next step within 7 seconds. 0 ON Page 7 of DOC.: #5 08 To exit valet mode: repeat steps to 5. Cycle ignition ON five times [5x /ON] rapidly. 0 0 Wait, LED will turn solid RED for seconds. Set ignition to position. ON Valet Mode Programming Procedure completed. Automotive Data Solutions Inc.
Page 8 of DOC.: #5 08 MODULE NAVIGATION PROCEDURE - OF It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 Module must be programmed to the vehicle. Use the Module Navigation Chart on the next page. 06 Set ignition to position. 07 TO ESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 ON TO ESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. 0 0 [X] Automotive Data Solutions Inc.
Page 9 of DOC.: #5 08 [Z] settings I Default settings are listed in bold. II Make sure the option is covered on the vehicle before attempting to change the setting. [Y] options module navigation chart: notes [X] menus module navigation chart - OF -0 enable 0 DISABLE* DISABLE 0 0 LOCK + UNLOCK + LOCK 0 LocK + LocK + LocK 0 MIN 0 MIN 0 0 MIN 0 5 MIN 5 MIN** 06 0 MIN** 07 5 MIN** 08 5 min 09- TAKEOVER 06 07 FACTORY KEYLESS RS SEQUENCE CONFIGURATION 08 0-07 Technical Support only MODULE RUN TIME *Vehicle will shutdown when a door is opened. **The maximum runtime for models is 0 minutes. Automotive Data Solutions Inc.
[X] number of PaRKing Light FLashes Diagnostic Remote starter error codes - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 Foot brake is ON. 0 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. Remote starter error codes: notes Automotive Data Solutions Inc. Page 0 of DOC.: #5 08
I II III DURING PROGRAMMING DURING REMOTE WITH IGNITION Automotive Data Solutions Inc. Diagnostic test module LeD status module Diagnostics - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. Page of DOC.: #5 08
MODULE RESET PROCEDURE - OF Disconnect all connectors from module except the BLACK -PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK -PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK -PIN connector. Failure to follow procedure may result with a DTC or a CHECK error message. 0 Wait, LED will flash RED. RELEASE programming button. LED will turn RED for seconds. 06 Module RESET completed. Automotive Data Solutions Inc. Page of DOC.: #5 08
TAKEOVER PROCEDURE - OF All vehicle doors must be closed and locked prior to remote start sequence. Press unlock on OEM or aftermarket remote or request switch. 0 ON Page of DOC.: #5 08 DO NOT PRESS BRAKE PEDAL. Set ignition to ON position. Wait seconds for key validation. 0 Press and release BRAKE pedal. 0 Take over procedure completed. Failure to follow procedure will result in vehicle engine shutdown. Automotive Data Solutions Inc.