Model Number Structure

Modulr Temperture E5ZN New DIN Trck Mounting Temperture Two chnnels of temperture control vilble despite width of only.5 mm. The Temperture itself cn be replced without chnging terminl wiring. Use in combintion with compct Setting Disply Unit to reduce communictions progrmming requirements. wide vriety of opertion indictors (single-color LEDs) enble esy opertion monitoring. Power supply nd communictions wiring not required between Units when mounted side-by-side. Model Number Structure Model Number Legend E5ZN- @ @ @ @ @ -FLK 1 3 4 5 6 7 1. Control points : Two points. Control output Q: Voltge (for driving SSR) T: Trnsistor C: Current 3. uxiliry output P: Trnsistor (sourcing) N: Trnsistor (sinking) 4. Option H: Heter burnout lrm F: Trnsfer output 5. Communictions 3: RS-485 6. Input type TC: Thermocouple P: Pltinum resistnce thermometer 7. CompoWy/F seril communictions -FLK: CompoWy/F seril communictions Temperture Modulr Temperture E5ZN I-19

Ordering Informtion List of Models Nme Temperture (See note 1.) Power supply 4 VDC No. of control points Control output Voltge output (for SSRs) Trnsistor output nlog output (current output) (See note.) uxiliry output Trnsistor output: pts (sinking) Trnsistor output: pts (sourcing) Trnsistor output: pts (sinking) Trnsistor output: pts (sourcing) Trnsistor output: pts (sinking) Trnsistor output: pts (sourcing) Heter burnout lrm (See note 3.) Trnsfer output (liner voltge output) (See note.) Functions Heting or het/cool control is selectble (See note 4.) Event input: 1 point per Unit Communictions functions RS-485 Input type (See note 5.) Thermocouple Pltinum resistnce thermometer Thermocouple Pltinum resistnce thermometer Thermocouple Pltinum resistnce thermometer Thermocouple Pltinum resistnce thermometer Thermocouple Pltinum resistnce thermometer Thermocouple Pltinum resistnce thermometer Model E5ZN-QNH3TC-FLK E5ZN-QNH3P-FLK E5ZN-QPH3TC-FLK E5ZN-QPH3P-FLK E5ZN-TNH3TC-FLK E5ZN-TNH3P-FLK E5ZN-TPH3TC-FLK E5ZN-TPH3P-FLK E5ZN-CNF3TC-FLK E5ZN-CNF3P-FLK E5ZN-CPF3TC-FLK E5ZN-CPF3P-FLK Note: 1. Terminl Units re required for wiring. Purchse seprtely.. When connecting the lod of the controlled system, het control output or cool control output cn be llocted to the control output or uxiliry output. When connecting recording device or Digitl Pnel Meter, trnsfer output cn be llocted to control output or uxiliry output 3 or 4 of nlog output models. 3. When using the heter burnout lrm, purchse Current Trnsformer (CT) seprtely. 4. When using heting nd cooling control functionlity, the uxiliry output will be either heting control output or cooling control output. 5. nlog input nd infrred temperture sensors (ES1-) cn lso be used with thermocouple models. Nme No. of terminls Functions Model Terminl Unit (Includes bus system without bckplne.) Note: 1. When using or more E5ZNs mounted side-by-side, use the E5ZN-SCT18S-5 for the second nd subsequent Units. When using E5ZNs seprtely, be sure to use the E5ZN-SCT4S-5.. Two End Pltes re provided with E5ZN-SCT4S-5 Terminl Units. When mounting to DIN trck, be sure to mount End Pltes on both sides. Current Trnsformer (CT) (Order Seprtely) Terminl Cover 4 18 (See note 1.) Model E54-CT1 E54-CT3 Dimeter 5.8 di. 1. di. Model E53-COV1 E53-COV13 Type For SCT4S-5 models For SCT18S-5 models Note: The Terminl Cover comes with the Terminl Unit nd does not hve to be purchsed seprtely. Equipped with communictions terminls for power supply, communictions, nd setting devices. Not equipped with communictions terminls for power supply, communictions, nd setting devices. Sockets (for Setting Disply Unit - Order Seprtely) E5ZN-SCT4S-5 E5ZN-SCT18S-5 Setting Disply Unit (Order Seprtely) Nme Power supply Model Setting Disply Unit 4 VDC E5ZN-SDL (See note.) Note: Purchse sockets for wiring (shown on pge 13) seprtely. Model PCF-11 PCF-11-E P3G-11 Y9-48G Type Front-connecting socket Terminl cover for finger Front-connecting socket Bck-connecting socket (with finger protection) protection Note: Refer to the following mnul for precutionry informtion nd other informtion necessry to use the E5ZN: E5ZN Temperture Opertion Mnul (Ct. No. H113). I-13 Modulr Temperture E5ZN

Specifictions Rtings Power supply voltge llowble voltge rnge Power consumption Sensor input Control output uxiliry output 4 VDC 85% to 11% of the rted power supply voltge pprox. 3 W Thermocouple: K, J, T, E, L, U, N, R, S, B Infrred temperture sensor (ES1 series): 1 to 7 C, 6 to 1 C, 115 to 165 C, 16 to 6 C (See note 1.) Voltge input: to 5 mv Pltinum resistnce thermometer: Pt1, JPt1 Voltge output (for driving SSR) Trnsistor output Current output Trnsistor output Liner voltge output Output voltge: 1 VDC ±15% (PNP); Mximum lod current: 1 m; Equipped with short-circuit protection circuit Mximum opertionl voltge: 3 VDC; Mximum lod current: 1 m; Residul voltge: 1.5 V mx.; Lekge current:.4 m mx. Current output rnge: 4 to / to m DC; Lod: 35 Ω mx. (See note.) Sourcing Sinking Mximum operting voltge: 3 VDC; Mximum lod current: 5 m; Residul voltge: 1.5 V mx.; Lekge current:.4 m mx. Voltge output rnge: 1 to 5/ to 5 VDC; Lod: 1 kω min. Contct output ON: 1 kω mx., OFF: 1 kω min. Dischrge current: pprox. 7 m Event input Non-contct output ON: Residul voltge: 1.5 V mx., OFF: Lekge current:.1 m mx. Dischrge current: pprox. 7 m Number of input nd control points Input points:, Control points: Setting method Vi communictions or using the Setting Disply Unit (E5ZN-SDL) Control method -PID or ON/OFF control Other functions mbient operting temperture Heter burnout detection function, trnsfer output function Multi-SP nd RUN/STOP switching using event input 1 to 55 C (with no icing or condenstion) For 3 yers of ssured use: 1 to 5 C mbient operting humidity 5% to 85% Storge temperture 5 to 65 C (with no icing or condenstion) Note: 1. ES1 models with temperture rnge of 16 C to 6 C hve been discontinued.. OMRON G3-E Cycle Unit (lod impednce 35 Ω) cn be used. Input Rnge Pltinum Resistnce Thermometer Models nd Thermocouple Models Input type Nme Temperture rnge ( C) 18 17 16 15 14 13 1 11 1 9 8 7 6 5 4 3 1 1 Setting number Pltinum resistnce thermometer models Pltinum resistnce thermometer Pt1 JPt1 85 5. 5. 1.... 199.9 199.9 133 5. 85 4. 4 4. Thermocouple K J T E L U N R S B 4 4.. 1. 1 199.9 199.9. 3 4 3 4 17 5 6 7 18 8 9 11 1 13 14 15 16 The pplicble stndrds for the input types re s follows: K, J, T, E, N, R, S, B: JIS C16-1995, IEC584-1 L: Fe-CuNi, DIN 4371-1985 U: Cu-CuNi, DIN 4371-1985 JPt1: JIS C 164-1989, JIS C 166-1989 Pt1: JIS C 164-1997 IEC 751 Shded prts indicte the settings t the time of purchse. Note: ES1 models with temperture rnge of 16 C to 6 C hve been discontinued. 6 85 Thermocouple models 18 177 Infrred temperture sensor (ES1) nlog input 1 to 6 to 115 to16 to 7 C 1 C165 C 6 C to 5 mv 9 1 165 6 1999 to 9999 or 199.9 to 999.9 by scling Temperture Modulr Temperture E5ZN I-131

Chrcteristics Indiction ccurcy Thermocouple: (Indicted vlue ±.5% or ±1 C, whichever is greter) ±1 digit mx. (See note 1.) Pltinum resistnce thermometer: (Indicted vlue ±.5% or ±1 C, whichever is greter) ±1 digit mx. (See note 1.) nlog input: ±.5% or ±1 digit mx. CT input: ±5% FS ±1 digit mx. Trnsfer output ccurcy: ±.5% FS (See note.) Hysteresis.1 to 999.9 EU (in units of.1 EU) (See note 3.) Proportionl bnd (P).1 to 999.9 EU (in units of.1 EU) (See note 3.) Integrl time (I) to 3,999 s (in units of 1 s) Derivtive time (D) to 3,999 s (in units of 1 s) Control period 1 to 99 s (in units of 1 s) Mnul reset vlue. to 1.% (in units of.1%) lrm setting rnge 1,999 to 9,999 (Position of deciml point depends on input type.) Smpling period 5 ms Insultion resistnce MW min. (t 5 VDC) Dielectric strength 6 VC for 1 minute t 5 or 6 Hz (between unlike terminls of chrged prts) Vibrtion resistnce 1 to 55 Hz, 1 m/s for hrs ech in X, Y, nd Z directions Shock resistnce 15 m/s mx., 3 times ech in ±X, ±Y, nd ±Z directions Enclosure rting Temperture : IP Terminl Unit: IP Memory protection EEPROM (non-voltile memory) (Number of write opertions: 1,) Weight pproved stndrds (See note 4.) Temperture : pprox. 9 g Terminl Unit (18): pprox. 8 g Terminl Unit (4): pprox. 1 g UL File No.: E593 CS File No.: 3889-11484 CE EMS: ESD EN6136, EN61-4- (4 kv/contct, 8 kv/ir) REM field EN6136, EN61-4-3 (1 V/m) Fst trnsient EN6136, EN61-4-4 ( kv/dc power, 1 kv/i/o) Surge immunity EN6136, EN61-4-5 (line to ground: kv/dc power 1 kv/i/o line to line: 1 kv/dc power) Conducted RF EN6136, EN61-4-6 (1 V) EMI: Rdited EN6136 Clss Note: 1. The indiction ccurcy for T nd N thermocouples t 1 C, nd for U nd L thermocouples is ± C ±1 digit mx. There is no specifiction for the indiction ccurcy for the B thermocouple used t 4 C mx. The indiction ccurcy for R nd S thermocouples t C mx. is ±3 C ±1 digit mx.. The trnsfer output ccurcy for to 4 m when to m DC is selected is ±.5% FS.7 m. The trnsfer output ccurcy for to 1 V when to 5 VDC is selected is ±.5% FS.175 V. 3. EU stnds for Engineering Unit. 4. In order to stisfy the EN6136 Clss stndrd for conducted emissions, instll noise filter (Densei-Lmbd MXB-16-33 or equivlent) in DC power line s close to the E5ZN s possible. I-13 Modulr Temperture E5ZN

Communictions (Host Communictions) Trnsmission line connection method Communictions method Synchroniztion method Bud rte Trnsmission code Dt bit length (See note.) Stop bit length (See note.) Error detection Flow control Interfce Retry function Number of Units tht cn be connected in prllel RS-485 multipoint RS-485 (-wire, hlf-duplex) Strt-stop synchroniztion 4,8, 9,6, 19,, or 38,4 bps SCII 7 or 8 bits 1 or bits Verticl prity (none, even, odd) BCC (block check chrcter) None RS-485 None 16 Units mx. (3 chnnels) Note: The bud rte, dt bit length, stop bit length, nd verticl prity cn ll be set independently s host communictions settings. Setting Disply Unit (Order Seprtely) Rtings nd Chrcteristics Current Trnsformer (CT) Rtings (Order Seprtely) Dielectric strength 1, VC (1 minute) Vibrtion resistnce 5 Hz, 98 m/s Weight ccessories (E54-CT3 only) Heter Burnout lrm Chrcteristics Mximum heter current Input current redout ccurcy Heter burnout lrm setting rnge Minimum detection ON time E54-CT1: pprox. 11.5 g E54-CT3: pprox. 5 g rmture () Plug () Single-phse, 5 C (See note 1.) ±5% FS ±1 digit mx.. to 5. (in units of.1 ) (See note.) 19 ms (See note 3.) Note: 1. Use the KCU-F@@-@GS (with GTE input terminl) for burnout detection of 3-phse heters.. If the heter burnout lrm setting is set to., the lrm is lwys OFF, nd if it is set to 5. the lrm is lwys ON. 3. If the ON time for control output is less thn 19 ms, heter burnout detection nd heter current mesurement will not be performed. Power supply voltge llowble voltge rnge Power consumption Disply method mbient operting temperture mbient operting humidity Storge temperture Communictions method Communictions formt Insultion resistnce Dielectric strength Vibrtion resistnce Shock resistnce Enclosure rtings Memory protection Weight 4 VDC 85% to 11% of the rted power supply voltge pprox. 1 W 7-segment digitl disply nd single-color disply 1 to 55 C (with no icing or condenstion) For 3 yers of ssured use: 1 to 5 C 5% to 85% 5 to 65 C (with no icing or condenstion) RS-485 (hlf-duplex) Fixed MW min. (t 5 VDC) 1,5 VC for 1 minute t 5 or 6 Hz (between unlike terminls of chrged prts) 1 to 55 Hz, m/s for hrs ech in X, Y, nd Z directions 3 m/s mx., 3 times ech in ±X, ±Y, nd ±Z directions Front pnel: IP5 Rer cse: IP Terminl cse: IP EEPROM (non-voltile memory) (Number of writes: 1,) pprox. 1 g Mounting brcket: pprox. 1 g Temperture Modulr Temperture E5ZN I-133

Nomenclture E5ZN- Opertion Indictors POWER Lights when power is turned ON. ERROR Lights when ftl error (e.g., memory error or sensor error) occurs. SD/RD (Communictions Opertion) Flshes during communictions with the host. OUT1 (Control Output 1) Lights when the control output 1 is ON. OUT (Control Output ) Lights when the control output is ON. SUB1 (uxiliry Output 1) Lights when the uxiliry output 1 is ON. SUB (uxiliry Output ) Lights when the uxiliry output is ON. POWER ERROR SD/RD OUT1 OUT SUB1 SUB Unit Number Setting Setting rnge of to F llows up to 16 Units to be set. Bud Rte E5ZN-SDL The following digrm shows the nmes nd functions of the E5ZN-SDL prts for when it is connected to the E5ZN-@@@@@@@. Opertion Indictors These indictors indicte the terminl opertions for the E5ZN-@@@@@@@. OUT1, OUT (Control Output 1, Control Output ) Light when the control output 1 or the control output functions re ON. SUB1, SUB (uxiliry Output 1, uxiliry Output ) Light when the uxiliry output 1 or the uxiliry output functions re ON. STOP Lights when opertion stops. Lights for n event or when RUN/STOP is set to STOP during control. Remins unlit t other times. CMW (Communictions Write Control) Lights when communictions write is permitted nd remins unlit when it is prohibited. SUB3 (uxiliry Output 3) Pulse output models: lwys not lit. nlog output models: Not lit when the uxiliry output drops to % or lower. Lit when the uxiliry output is bove %. SUB4 (uxiliry Output 4) Pulse output models: lwys not lit. nlog output models: Not lit when the uxiliry output drops to % or lower. Lit when the uxiliry output is bove %. Unit/Chnnel Indictor Indictes the unit number nd the chnnel number. Level Key Press this key to switch setting levels. Mode Key Press this key to switch setting dt within the setting level. Temperture Unit Displyed when the disply unit for setting dt is temperture. The disply is determined by the setting for temperture unit, with either C or F displyed ccordingly. UNIT Key Press to switch the unit number. Level Key nd Mode Key Press together to switch to protect mode. No. 1 Disply Displys the PV or the type of setting dt. No. Disply Displys the trget vlue, the control vrible, or the set vlue for setting dt (setting contents). Up Key Ech time this key is pressed, the vlue displyed in No. Disply increses. If it is held down, the rte of increse becomes fster. It cn lso be used to move to the next setting item. Down Key Ech time this key is pressed, the vlue displyed in No. Disply decreses. If it is held down, the rte of decrese becomes fster. It cn lso be used to return to the previous setting item. Chnnel Key Press this key to chnge the chnnel number. Copy Key Press this key to red ll the settings from the Temperture to the Setting Disply Unit, or to write from the Setting Disply Unit to the Temperture. I-134 Modulr Temperture E5ZN

Dimensions Note: ll units re in millimeters unless otherwise indicted. E5ZN-@@@3@-FLK Connected to E5ZN-SCT4S-5 E5ZN-@@@3@-FLK Connected to E5ZN-SCT18S-5 46 35 7 11 46 35 7 11 7.8 13 7.8 13 When only using one Unit, purchse the E5ZN-@@@3@- FLK nd the E5ZN-SCT4S-5 together. lso, when using horizontl side-by-side mounting, purchse the first Unit together with the E5ZN-SCT4S-5..3 3 4.7 When mounting Units side-byside, purchse the E5ZN- @@@3@-FLK together with the E5ZN-SCT18S-5 for the second nd subsequent Units. 5..5 4.7 Note: Refer to the following mnul for precutionry informtion nd other informtion necessry to use the E5ZN: E5ZN Modulr Temperture User s Mnul (Ct. No. H113). End Plte PFP-M Spcer PFP-S Eight, M4 pn-hed screws 5 1 6. 1.8 1 35.5 35.3 1.8 5 44.3 16 1 34.8 11.5 1 M4 spring wsher 1.3 4.8 16.5 Note: End Pltes re provided with the E5ZN-SCT4-5. Be sure to mount End Pltes t both ends of Unit blocks. Current Trnsformer (Order Seprtely) E54-CT1 5 3 1 1 15 4.8 5.8 di. 7.5 1.5 Two, 3.5 di. E54-CT3 4 4 15 3.36 di. 1 di. 9 Two, M3 (Depth: 4) E54-CT3 ccessories rmture pprox. 3 di. Plug pprox. 6 di. 18 Connection Exmple rmture Plug Led wire () Temperture 3 3 Mounting Trck (for DIN Trck Mounting - Order Seprtely) PFP-1N PFP-5N 4.5 7.3±.15 35±.3 7±.1 15 5 5 5 5 1 1, (5)* 1 15 (5)* 1 * Indictes dimensions for the PFP-5N. Modulr Temperture E5ZN I-135

Setting Disply Unit E5ZN-SDL 48 48 6 (84) 63.7 14. Pnel Cutout Dimensions Individul Mounting Side-by-side Mounting (48 No. of Units.5) 1. 45.6 E5ZN-SDL Wiring Sockets Front-connecting Sockets 44.8 44.8 6 min. 45.6 45.6 The mounting pnel thickness is 1 to 5 mm. Verticl side-by-side mounting is not possible. (llow sufficient spce bove nd below.) When mounting severl Units, mke sure tht the mbient tem-perture specifictions re not exceeded. PF-11 (Stndrd Model) 5 mx. 31. mx. Two, 4.5-di. holes Eleven, M3.5 7.5 Sems screws 7.8 4 7 mx. 3 35.4 4.5 Terminl rrngement/ Internl Connections (TOP VIEW) Mounting Hole Cutout Dimensions PF-11-E (with Finger Protection) 5 mx. 4 ±. 31. mx. 3 Two, M4 or 4.5 di. 4 ±. Two, 4.5-di. holes 3 7 mx. 1. 4 35.4 Note: DIN trck mounting is lso possible. Eleven, M3.5 7.5 set screws Bck-connecting Sockets 7.8 5 4.5 P3G-11 (Stndrd Model) 7 di. 4 7 3 Terminl rrngement/ Internl Connections (BOTTOM VIEW) 45 5.6 45 4.5 16.3 Note: Use in combintion with Terminl Cover (Y9-48G) for finger protection. 6. 8.7 6 Terminl Cover Y9-48G Twelve, 6.4 di. 34 47.7 47.7 48 48 16.5 4.6 7.6 47.4 I-136 Modulr Temperture E5ZN

Instlltion Connection Digrms Voltge output (control output) is not electriclly isolted from internl circuitry. Therefore, when using grounded thermocouples, do not ground control output terminls. (Doing so my result in temperture mesurement errors due to unwnted current pths.) There is bsic insultion between the power supply inputs nd outputs for this product. If reinforced insultion is required, connect the input nd output terminls to equipment without ny exposed chrge-crrying prts, or to equipment with bsic insultion sufficient for the mximum operting voltge of the power supply nd the inputs nd outputs. Using with the E5ZN-SCT4S-5 4-VDC input power supply* Wiring for terminls 1 to 18 is the sme s for the E5ZN-SCT18-5. See below. *Power supply: recommended power supply; eg. OMRON S8VS E5ZN-SDL RS-485 host Using with the E5ZN-SCT18S-5 7 OUT1 8 ch1 1 4- m DC/ - m DC OUT ch nlog-output type E5ZN-C@F3@-FLK 4- m DC/ - m DC 13 SUB1 14 SUB 15 COM PNP (sourcing) type E5ZN-@P@3@-FLK CT ch CT1 ch1 16 17 18 Voltge-output type E5ZN-Q@H3@-FLK Trnsistor-output type E5ZN-T@H3@-FLK 13 SUB1 14 SUB 15 COM NPN (sinking) type E5ZN-@N@3@-FLK 16 1-5 VDC/ SUB3-5 -VDC SUB4 17 1-5 VDC/ -5 VDC 18 nlog-output type (liner-voltge-output) E5ZN-C@F3@-FLK 13 7 1 14 15 16 17 18 8 9 1 11 1 3 4 5 6 Event input Contct input E5ZN-SCT18S-5 Noncontct input 1 11 OUT1 1 6 ch1 ch Thermocouple/infrred temperture sensor 4 5 7 1 1 VDC 1 m OUT 8 Voltge-output type E5ZN-Q@H3@-FLK 1 11 1 ch1 Pt 4 5 6 7 OUT1 8 1 VDC 1 m OUT ch 1 4 11 5 V V 1 6 ch1 ch nlog input 1 ch1 ch Trnsistor-output type E5ZN-T@H3@-FLK Temperture E5ZN-SDL When the E5ZN-SCT4S-5 is used Do not use. Host side (RS-485) Do not use. Note: Purchse either PCF-11 or P3G-11 Socket seprtely. (Refer to pge 136.) 4 VDC input power supply Recommended power supply; eg. Omron S8VS. Note: 1. Terminls 4 nd 9, 7 nd 11, nd 8 nd 1 re connected internlly t the E5ZN-SDL side.. Do not connect nything to terminls 1,, 5, nd 6. Modulr Temperture E5ZN I-137

Opertion E5ZN-SDL Setting Dt The setting dt tht cn be set from the E5ZN-SDL Setting Disply Unit is shown below. Depending on the protection settings nd other fctors, some settings my not be displyed. pssword is required to move to the dvnced function setting level. The disply below indictes tht there is setting dt for ch1 or ch. 1 in-h 1 Press the CH Button to switch between the screens for ch1 nd ch. ch: in-h 1 ch1: CH in-h 1 Communictions setting level @ Key 1 s mx. len 7 sbit prty euen Communictions dt length Communictions stop bit Communictions prity P : This symbol indictes setting dt tht is displyed only for models with pulse output. ("Models with pulse output" is used here to indicte models with voltge output or trnsistor output.) : This symbol indictes setting dt tht is displyed only for models with nlog output. sdwt Communictions response wit time dvnced function setting level init eu-m 1 eu none mspu sprt rest l1n n-o lh1. ln CHn-o lh. l3n CHn-o lh3. hbu on hbl hbh.1 Prmeter initilize Number of multi-sp uses Event input lloction Multi-SP uses SP rmp set vlue HB ON/OFF P Heter burnout ltch P Heter burnout hysteresis P Move to the dvnced function setting level by entering the pssword "169". Stndby sequence reset lrm 1 open in lrm lrm 1 hysteresis lrm open in lrm lrm hysteresis lrm 3 open in lrm lrm 3 hysteresis - CH 5. ot- sedu 3 mou lf.65 ol-h 15. ol-l inf. pud isdp istp 1lt lt 3lt sero cjc on Voltge output type Top of initil setting level Sensor error indictor used Move to dvnced function setting level α -PID prmeter MV upper limit MV lower limit Input digitl filter dditionl PV disply dditionl temperture input shift vlue disply Temperture input shift type lrm 1 ltch lrm ltch lrm 3 ltch Input error output Cold junction compensting method Top of dvnced function setting level @ Key 1 s min. out 5 sub1 sub 7 sub3 1 sub4 17 cont no tr1h 13 tr1l - trh 13 trl - tr3h 13 tr3l - tr4h 13 tr4l - ot-1 Control output lloction uxiliry output 1 lloction uxiliry output lloction uxiliry output 3 lloction uxiliry output 4 lloction Opertion fter power ON OUT1 trnsfer output upper limit OUT1 trnsfer output lower limit OUT trnsfer output upper limit OUT trnsfer output lower limit SUB3 trnsfer output upper limit SUB3 trnsfer output lower limit SUB4 trnsfer output upper limit SUB4 trnsfer output lower limit Current output type Initil setting vlue in-t in-h 1 in-l dp d-u c sl-h 13 sl-l - cntl onof cp c-cp oreu or-r lt1 lt lt3 out1 Input type Scling upper limit Scling lower limit Deciml point Temperture unit SP upper limit SP lower limit PID ON/OFF Control period (het) Control period (cool) Direct/reverse opertion lrm 1 type lrm type lrm 3 type @ Key @ Key Control output 1 lloction I-138 Modulr Temperture E5ZN

Protect level During control Control stopped Copy mode opt Opertion/djustment protection Power ON Returns utomticlly or when the COPY Key is pressed for 1 s mx. COPY Key 1 s min. @ nd Keys 1 s min. @ nd Keys 3 s min. icpt wtpt Initil setting/ communictions protection Setting chnge protection 1 s min. 3 s min. Opertion level @ Key, 1 s min. @ Key, 1 s min. djustment level 5 PV t T execute/cncel 5 PV/SP c-sc 1. Cooling coefficient cmwt on Communictions writing m-sp sp-m Multi-SP SP rmp monitor c-db. of-r 5. Ded bnd Mnul reset vlue ct. hb. Heter current vlue monitor P Heter burnout detection P ct. Heter current vlue monitor P hys 1. Heting hysteresis sp- SP r-s stop Run/stop chys 1. Cooling hysteresis sp-1 SP 1 l-1 lrm vlue 1 Strt of djustment level ins. Temperture input shift l1h l1l Upper-limit lrm vlue 1 Lower-limit lrm vlue 1 insh. insl. Upper-limit temperture input shift vlue Lower-limit temperture input shift vlue Temperture l- lrm vlue p 8. Proportionl bnd lh Upper-limit lrm vlue i 33 Integrl time ll Lower-limit lrm vlue d 4 Derivtive time l-3 lrm vlue 3 o. MV monitor for heting c-o. MV monitor for cooling Top of opertion level Modulr Temperture E5ZN I-139

UNIT BPS POWER ERROR SD/RD OUT1 OUT SUB1 SUB E5ZN Exmples of Functions Using s Temperture Input Signl Converter Trnsfer Output Types The ten types of dt shown below cn be llocted for trnsfer output using the control output 1 lloction, control output lloction, uxiliry output 3 lloction, nd uxiliry output 4 lloction (initil setting level). Trnsfer output is supported by nlog output models only. ch1 ch Trnsfer output for ch1 set point Trnsfer output for ch set point Trnsfer output for ch1 rmp set point Trnsfer output for ch rmp set point Trnsfer output for ch1 process vlue Trnsfer output for ch process vlue Trnsfer output for ch1 heting control MV Trnsfer output for ch1 cooling control MV Trnsfer output for ch heting control MV Trnsfer output for ch cooling control MV Note: Control outputs 1 nd use current output nd uxiliry outputs 3 nd 4 use liner voltge output. Trnsfer Output Scling The rnge set by the trnsfer output upper limit nd trnsfer output lower limit (initil setting level) cn be scled to the output rnge for the trnsfer output (4 to m DC or to m DC for control outputs 1 nd, nd to 1 to 5 VDC or to 5 VDC for uxiliry outputs 3 nd 4). The scle cn be expnded by setting smll rnge between the trnsfer output upper nd lower limits. Reverse scling cn be performed by setting the trnsfer output upper limit to vlue smller thn the trnsfer output lower limit. The following figure shows scling exmple where the heting control MV trnsfer output is scled to 1 to 5 VDC. Exmple: Scling to 1 to 5 VDC Trnsfer output (V) Exmple : Displying the ch Process Vlues on n Externl Meter Using Trnsfer Output Temperture : E5ZN-C@F3P-FLK (current output, pltinum resistnce thermometer input) Meter: K3M-J 4 VC/VDC (Process Meter) Temperture Settings: Sensor input type (initil setting level): (pltinum resistnce thermometer,. C to 1. C) Control output lloction (initil setting level): 17 (process vlue trnsfer output for ch) OUT trnsfer output upper limit (initil setting level): 1. ( C) OUT trnsfer output lower limit (initil setting level): ( C) Current output type (initil setting level): (4 to m DC) Meter Setting Exmple: Inputs for 4 to m DC re scled to. to 1. C. Input type (initil setting level: in-t): 4 to m DC (4-) Scling input vlue 1 (initil setting level: inp.1): 4 m (4.) Scling disply vlue 1 (initil setting level: dsp.1): () Scling input vlue (initil setting level: inp.): m (.) Scling disply vlue (initil setting level: dsp.): 1 (1) Deciml point (initil setting level: dp): One deciml plce (.) Temperture E5ZN-C@F3P-FLK Input terminl (E5) 4 to m DC output Input terminl (E6) Control output (current output) Terminls 1 nd Process Meter K3M-J 4 VC/VDC MX/MIN LEVEL MODE SHIFT UP Shethed pltinum resistnce thermometer 5 1 1 Trnsfer output lower limit Heting control MV (%) 1 8 Trnsfer output upper limit ch input (pltinum resistnce thermometer input) Terminls 4, 5, nd 6 B (white/blck) (red) B (blck/white) Reding Tempertures for Multiple E5ZN Units With conventionl models, if the present temperture is red from multiple Temperture s using host communictions, there re time differences in the process tempertures red from ech Temperture, mking it difficult to obtin concurrent dt. With the E5ZN, the PV hold function cn be used to ensure tht the dt is concurrent to within 5 ms. PV Hold The PV hold function temporrily stores the present temperture for tht moment s the PV hold vlue, when the "PV hold" opertion commnd sent by host communictions is received. (See fig. 1.) Fig. 1 (1) "PV hold" executed. Host (3) "PV hold vlue" red. Unit No. Unit No. 15 (1) "PV hold" is executed from the host computer. () The present temperture for ech E5ZN Unit from Units No. to 15 is written simultneously to PV hold vlues. (3) The PV hold vlues re red in order, strting with Unit No.. () The present temperture is held. Note: 1. PV hold vlues re overwritten every time the "PV hold" opertion commnd is executed. Once the PV hold vlues hve been red for chnnels tht require simultneous reding of present tempertures, execute the next "PV hold" opertion commnd.. The "PV hold" opertion commnd cnnot be executed nd the "PV hold vlue" cnnot be red from the E5ZN-SDL Setting Disply Unit. 3. When the power is turned OFF, the PV hold vlues chnge to. I-14 Modulr Temperture E5ZN

Precutions Generl Precutions The user must operte the product ccording to the performnce specifictions described in the opertion mnul. Before using the product under conditions tht re not described in the mnul or pplying the product to nucler control systems, rilrod systems, vition systems, vehicles, combustion systems, medicl equipment, musement mchines, sfety equipment, nd other systems, mchines, nd equipment tht my hve serious influence on lives nd property if used improperly, consult your OMRON representtive. Mke sure tht the rtings nd performnce chrcteristics of the product re sufficient for the systems, mchines, nd equipment, nd be sure to provide the systems, mchines, nd equipment with double sfety mechnisms. Sfety Precutions Definition of Precutionry Informtion!WRNING The bove symbol indictes sitution tht my result in injury or property dmge. Wrnings!WRNING Do not llow metl frgments or led wire scrps to fll inside this product. These my cuse electric shock, fire, or mlfunction.!wrning Do not use the product in loctions subject to flmmble or explosive gses. Doing so my result in explosion.!wrning Do not touch ny of the terminls while the power is ON. Doing so my result in electric shock.!wrning Provide t lest one power-interruption switch to ensure tht the power is OFF before wiring. Not doing so my result in electric shock.!wrning To mintin sfety in the event of product mlfunction, lwys tke pproprite sfety mesures, such s instlling n lrm on seprte line to prevent excessive temperture rises. If mlfunction prevents proper control, mjor ccident my result.!wrning Do not ttempt to disssemble, repir, or modify the product. ny ttempt to do so my result in mlfunction, fire, or electric shock.!wrning Tighten screws to the specified torques given below. Loose screws my result in burning or mlfunction. E5ZN-SCT@S-5:.4 to.56 N m E5ZN-SDL:.74 to.9 N m ppliction nd Operting Environment Precutions Observe the following points to ensure sfe opertion. 1. Use nd store the product within the specified temperture nd humidity rnges. Cool the product (e.g., using fns) where necessry.. Do not touch the electronic components or pttern of the PCB. Hold the product by the cse. 3. To ensure proper het dissiption, leve spce round the product. Do not block the product s ventilting holes. 4. Use t the rted power supply voltge with the rted lod. 5. Be sure to connect terminls with the correct polrity. 6. Perform wiring using crimp terminls of the specified size. (E5ZN- SCT@S-5: M3., width 5.8 mm mx.; E5ZN-SDL: M3.5, width 7. mx.) 7. Be sure to use wires stisfying the following specifictions for connection using bre wires. Power supply terminls: WG to 14 Other terminls: WG 8 to 16 (Length of exposed prt: 6 to 8 mm) 8. Do not connect nything to unused terminls. 9. Ensure tht the rted voltge is reched within seconds of turning power ON. 1.llow 3 seconds wrm-up time. 11.Instll the product s fr wy s possible from devices tht generte strong, high-frequency noise nd devices tht generte surges. 1.Keep wiring seprte from high-voltge power lines or power lines crrying lrge currents. Do not wire in prllel with or together with power lines. 13.Instll switches or circuit-brekers so tht the user cn turn the power OFF immeditely, nd indicte these ccordingly. 14.Do not use the product in the following loctions: Loctions subject to dust or corrosive gses (in prticulr, sulfide gs nd mmoni gs) Loctions subject to freezing or condenstion Loctions exposed to direct sunlight Loctions subject to vibrtions or shocks Loctions subject to exposure to wter or oil Loctions subject to het rdited directly from heting equipment Loctions subject to intense temperture chnges 15.When the Terminl Unit is seprted from the Temperture, under no circumstnces touch the electricl components or pply shock to the Temperture. 16.Do not use solvents to clen the product. Use commercil lcohol. 17.fter wiring is completed remove the dust-protection lbel to llow proper het dissiption. 18.When mounting the Temperture to the Terminl Unit, mke sure tht the hook on the side of the Temperture fcing the Terminl Unit is inserted properly. 19.Instll the DIN trck verticlly. Correct Use Temperture!WRNING Set ll settings ccording to the control trget of the product. If the settings re not pproprite for the control trget, the product my operte in n unexpected mnner, resulting in dmge to the product or ccidents. Service Life Use within the following temperture nd humidity rnges: Temperture: 1 to 55 C (with no icing or condenstion) Humidity: 5% to 85% Modulr Temperture E5ZN I-141

If the product is instlled inside control pnel, the temperture round the product (nd not the temperture round the control pnel) must be kept below 55 C. With electronic devices like the E5ZN, the service life will depend not only on the number of switching opertions performed by the rely but lso on the service life of the internl electronic components. The service life of these components depends on the mbient temperture; it will be shorter if the mbient temperture is high, nd longer if the mbient temperture is low. For this reson, the service life of the product cn be lengthened by keeping the inside of the E5ZN t low temperture. If severl Units re mounted side-by-side or re rrnged verticlly, the het generted my cuse the internl temperture of the Units to rise, reducing service life. To prevent this, tke steps to ensure tht the Units re cooled, such s instlling fns. Ensure, however, tht the terminls re not lso cooled, otherwise correct temperture mesurement will not be possible. Mesurement ccurcy When extending the led wires for thermocouples, use compensting conductor pproprite for the type of thermocouple used. When extending the led wires for pltinum resistnce thermometers, use led wires with low resistnce, nd mke the resistnce in the 3 led wires equl. Mount the E5ZN horizontlly. If significnt errors occur, check tht input compenstion hs been set correctly. Mounting nd Dismounting To mount using mounting trck, first hook prt (see below) onto the trck nd then push down on prt B. To dismount, insert flt-blded screwdriver into prt C, pull the hook down, nd then lift the bottom prt of the E5ZN upwrds. Wterproofing The enclosure rtings re given below. Prts for which the enclosure rting is not clerly indicted, nd prts with IP@ rtings (where @ is not ) do not hve wterproof specifictions. Temperture : IP Terminl Unit: IP Stopper 3 mm min. Mount the E5ZN t lest 3 mm wy from other devices to ensure esy mounting nd dismounting. Note: Refer to the following mnul for precutionry informtion nd other informtion necessry to use the E5ZN: E5ZN Temperture Opertion Mnul (Ct. No. H113). I-14 Modulr Temperture E5ZN

Wrrnty nd Limittions of Libility WRRNTY OMRON's exclusive wrrnty is tht the products re free from defects in mterils nd workmnship for period of one yer (or other period if specified) from dte of sle by OMRON. OMRON MKES NO WRRNTY OR REPRESENTTION, EXPRESS OR IMPLIED, REGRDING NON-INFRINGEMENT, MERCHNTBILITY, OR FITNESS FOR PRTICULR PURPOSE OF THE PRODUCTS. NY BUYER OR USER CKNOWLEDGES THT THE BUYER OR USER LONE HS DETERMINED THT THE PRODUCTS WILL SUITBLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DIS- CLIMS LL OTHER WRRNTIES, EXPRESS OR IMPLIED. LIMITTIONS OF LIBILITY OMRON SHLL NOT BE RESPONSIBLE FOR SPECIL, INDIRECT, OR CONSEQUENTIL DMGES, LOSS OF PROFITS, OR COMMER- CIL LOSS IN NY WY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLIM IS BSED ON CONTRCT, WRRNTY, NEGLI- GENCE, OR STRICT LIBILITY. In no event shll the responsibility of OMRON for ny ct exceed the individul price of the product on which libility is sserted. IN NO EVENT SHLL OMRON BE RESPONSIBLE FOR WRRNTY, REPIR, OR OTHER CLIMS REGRDING THE PRODUCTS UNLESS OMRON'S NLYSIS CONFIRMS THT THE PRODUCTS WERE PROPERLY HNDLED, STORED, INSTLLED, ND MINTINED ND NOT SUBJECT TO CONTMINTION, BUSE, MISUSE, OR INPPROPRITE MODIFICTION OR REPIR. ppliction Considertions SUITBILITY FOR USE OMRON shll not be responsible for conformity with ny stndrds, codes, or regultions tht pply to the combintion of products in the customer's ppliction or use of the products. t the customer's request, OMRON will provide pplicble third prty certifiction documents identifying rtings nd limittions of use tht pply to the products. This informtion by itself is not sufficient for complete determintion of the suitbility of the products in combintion with the end product, mchine, system, or other ppliction or use. The following re some exmples of pplictions for which prticulr ttention must be given. This is not intended to be n exhustive list of ll possible uses of the products, nor is it intended to imply tht the uses listed my be suitble for the products. Outdoor use, uses involving potentil chemicl contmintion or electricl interference, or conditions or uses not described in this ctlog. Nucler energy control systems, combustion systems, rilrod systems, vition systems, medicl equipment, musement mchines, vehicles, sfety equipment, nd instlltions subject to seprte industry or government regultions. Systems, mchines, nd equipment tht could present risk to life or property. Plese know nd observe ll prohibitions of use pplicble to the products. NEVER USE THE PRODUCTS FOR N PPLICTION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THT THE SYSTEM S WHOLE HS BEEN DESIGNED TO DDRESS THE RISKS, ND THT THE OMRON PRODUCTS RE PROPERLY RTED ND INSTLLED FOR THE INTENDED USE WITHIN THE OVERLL EQUIPMENT OR SYSTEM. Temperture Modulr Temperture E5ZN I-143

LL DIMENSIONS SHOWN RE IN MILLIMETERS. To convert millimeters into inches, multiply by.3937. To convert grms into ounces, multiply by.357. Ct. No. H116-E1- In the interest of product improvement, specifictions re subject to chnge without notice. I-144 Modulr Temperture E5ZN