APEM K range Power rocker switches and indicators Wide range Laser etched symbols Illuminated or nonilluminated Optionally sealed to IP8 Unique rocker design
K range Power rocker switches and indicators The K range at a glance A range of mix and match products KR rocker switches Attractive rugged rocker switches with more that.000.000 possible combinations. Custom laser etching. Page KL locking rocker switches Available with or positions, with one locked position. Patented intuitive ergonomics. Page KI indicators A complete indicator series with a wide choice of colours and a large number of LEDs. Long life expectancy. Page KG rocker switches With a raised protection bezel preventing inadvertent actuation of the rocker. Page Accessories Page Hole plug For future extensions. Connector For separate wiring. Mounting panel units To limit the number of cutouts. Removing tool APEM will be happy to develop custom product solutions. Please contact us with your requirements. www.apem.com APEM
Attractive rugged rocker switch KR series Power rocker switches Distinctive features Removable actuator Easy to stock Easy to customize Uptodate rocker design Smooth curves Wide choice of colours and symbols Laser etched symbols on illuminated versions Optional panel seal High performance LEDs Long life expectancy An array of colours and voltages High performance ultrasonic welding Protection against dust and the effects of continuous immersion under pressure. Integrated resistors Easy electrical connection Robust roller contact Very long life expectancy Many electrical functions available Large variety of terminal options Up to 0 terminals Screw, solder lug and quickconnect APEM will be happy to develop custom product solutions. Please contact us with your requirements. APEM www.apem.com
KR series Power rocker switches Specifications Unique rocker design Wide choice of colours Laser etched symbols Illuminated or nonilluminated Optionally sealed to IP8 ELECTRICAL SPECIFICATIONS Currrent/voltage rating with resistive load : Silver contacts (A) : A VDC, 00.000 cycles 0A VDC, 0.000 cycles (terminals. x 0.8 only) Gold plated contacts (D) : 0mA V, 0.000 cycles Initial contact resistance : 0 m max. Insulation resistance :.000 M min. at 00VDC Dielectric strength :.000 Vrms 0 Hz min. between terminals Mechanical life :0.000 cycles min. ENVIRONMENTAL SPECIFICATIONS Degree of protection of sealed versions : frontal sealing to IP8 according to IEC 09 (submersion under meter of water for more than 0 minutes) Salt spray resistance : 9 hours according to IEC, test f Vibration resistance : 000 Hz / 0 g per IEC 008 Operating temperature : 0 C to 8 C MATERIALS Case : PA Actuator : AS ezel : PA Terminals : brass, silver plated Contacts : silver (A) or silver, gold plated (D) Contact roller : brass, nickel plated SEALING Sealing is optional. To order a sealed product, complete the appropriate box of ordering format on the following pages..0 (.80) DIMENSIONS.00 (.9) Flat seal.0 (.98).00 (.7).00 (.) 0.00 Max (.99 Max) Dimensions : First dimensions are in mm while inches are shown as bracketed numbers. U8.00 (.98) Tolerance : The general tolerance for dimensions in this brochure is ± 0, (.0). Overall dimension tolerance is ± 0, (.00). 7.00 (.80) Packaging unit : 0 pieces Dimensions, specifications and data shown in this brochure are subject to change without notice. www.apem.com APEM
KR series Power rocker switches Selection guide HOW TO ORDER To order a complete product, fill in all the boxes of the following order guide. To order case only (without actuator), finish your order number with the LED wiring code. To order actuator only (without case), begin the order number with code KRR, then follow the order format from actuator type until the end of the options. CASE LEDS KR Side A Side SERIES Electrical functions Contacts Sealing LEDS Wiring Poles Single pole Double pole ON OFF ON ON ON R ON ON MOM MOM ON ON ON 7 MOM OFF MOM 8 ON OFF MOM 9 ON OFF ON Terminals A D Screw 0 terminals with barrier Solder lug/quickconnect terminals with barrier terminals w/o barrier A 0 term. with barrier 0 term. w/o barrier C 0 terminals for use with connector U9 Quickconnect,x0,8 terminals with barrier Silver Gold plated X K No Yes Terminals (continued) Quickconnect,x0,8 terminals w/o barrier D 0 term. with barrier E 0 term. w/o barrier F 0 term. for use with connector U9 Quickconnect,8x0,8 G 0 term. with barrier H 0 term. w/o barrier J 0 terminals for use with connector U8 X A C M R D E F N S J K L P T None LED V red LED V green LED V yellow LED V blue LED V white LED V red LED V green LED V yellow LED V blue LED V white LED V red LED V green LED V yellow LED V blue LED V white See diagrams page 9. ACTUATOR ACTUATOR MARKING Area A Area M Area Type Colour Orientation Symbols For nonilluminated application For illuminated application lue / Dark blue lack Green Grey Yellow Red 7 Ivory 9 Orange A Aluminium bright N O S E ON OFF ON OFF OFF ON OFF ON Symbols : see page. Accessories : see page. A M NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information. APEM www.apem.com
KR series Power rocker switches Case To order case only (without rocker), finish your order number with the LED wiring code. MODEL STRUCTURE CASE LEDS Contact area ottom view Contact & LED area Single pole Double pole KR KR ON OFF KR* ON ON ON KRR* ON ON MOM KR KR MOM ON KR KR ON ON KR7 KR7 MOM OFF MOM KR8 KR8 ON OFF MOM KR9 KR9 ON OFF ON 0 8 LED area * Function : single pole in double pole case 0 terminal version terminal version 9 7 ELECTRICAL FUNCTIONS AND CONNECTIONS In the tables below, terminal connections as viewed from bottom of switch. Only the contact area is represented. For single pole models, only terminals, and are to be considered (not terminals,, ). x = w/o terminal o = with terminal = momentary Positions Positions Function * KRKR Function 8 KR8KR8 Function KRKR Function 9 KR9KR9 Function KRKR Function KR Function 7 KR7KR7 Function R KRR * Function only available for terminal versions. www.apem.com APEM
KR series Power rocker switches Case TERMINALS CASE LEDS Screw Solder lug / quickconnect Normalized quickconnect,x0,8 Normalized quickconnect,8x0,8 Ø.00x0.0 SI (.8DIAx0.0 IS) Ø.0 (.DIA) ø.0 (.09DIA) Ø.0 (.07DIA). (.) 0.80 (.0).0 (.77).x0.80 (.x.0).x0.80 (.0x.0).80x0.80 (.0x.0) 0 term. with barrier terminals with barrier terminals w/o barrier A 0 terminals with barrier C 0 terminals w/o barrier 0 terminals for use with connector U9 terminals with barrier terminals w/o barrier D 0 terminals with barrier E F 0 terminals w/o barrier 0 terminals for use with connector U9 G H J 0 terminals with barrier 0 terminals w/o barrier 0 terminals for use with connector U8.8.0 (.9) (.) Terminals are marked on the case. The drawings show the maximum possible number of terminals..0 (.) 9.0 (.8).8 7.0 (.0) (.80) terminal version 0 terminal version CONTACT MATERIALS CASE LEDS A D Silver Silver, gold plated APEM www.apem.com 7
KR series Power rocker switches Case LEDs SEALING CASE LEDS X K No sealing IP8 (switch assembled on panel) Optional seal (K version) Ultrasonic welding of frame to case is standard on all versions. The ultrasonic welding and the optional panel seal prevent water and dust from introducing into the switch housing. Optional seal (K version) The product shall be installed professionally. Test conditions available on request. LEDS CASE LEDS Side A Side Complete each enlarged box with one of the codes listed below. X Without LED Side A Red Green Yellow lue White VDC A C M R VDC D E F N S VDC J K L P T LED consumption : 0mA @ nominal voltage ( C) Other illumination solutions : on request. 7 8 9 0 9 0 7 8 7 8 Side 9 0 9 0 7 8 8 www.apem.com APEM
WIRING CASE LEDS KR series Power rocker switches Case LEDs The LED wiring diagram is shown on the case. For terminal versions LED connected to the load A (standard) C Note : If not available, terminals are added to connect the LED. D for function (onoff) with LED on side A E F For 0 terminal versions Independent LED or integrated functions 8 7 8 0 9 0 7 9 8 7 0 9 To have independent LEDs. G (standard) H R 8 7 R R 8 7 8 7 R R 0 9 0 9 0 9 R Available in Single Pole only, with H and J quickconnect terminals. To obtain symbol illumination levels (night illumination when OFF and higher illumination when ON). Dotted line = external wiring, continuous line = internal wiring 8 7 0 9 To have a polarity inversion (typical application : fan motor). Dotted line = internal wiring, continuous line = internal wiring I Power supply betweeen and Load between and or and. Available with H and J quickconnect terminals. Please contact us for other wiring solutions. APEM www.apem.com 9
KR series Power rocker switches Actuator Marking To order actuator only (without case), begin the order number with code KRR, then follow the order format from actuator type until the end of the options. ACTUATOR TYPE ACTUATOR For nonilluminated application For illuminated application Other rocker design : on request. ACTUATOR COLOUR ACTUATOR Code Colour Code Colour lue Grey / Dark blue Yellow lack Green 7 Red Ivory Code 9 A Colour Orange Aluminium bright Note : colour 7 not available on illuminated versions. A softtouch varnish can be added. Consult us. MARKING ORIENTATION If no marking required, leave box blank. ACTUATOR MARKING ON ON OFF OFF OFF ON OFF ON Other orientations : on request N O S E 0 www.apem.com APEM
KR series Power rocker switches Marking Mounting SYMOLS ACTUATOR MARKING Available symbols : see page. Marking colour White marking for illuminated rockers (laser etching) and nonilluminated black rockers (pad printing). lack marking for nonilluminated colour rockers (pad printing). Other : on request. Laser etching resistance Water and petrol resistant acccording to EN08 Tear resistant (crosscut test) according to NF ISO 09 : class 0 UV resistant according to ISO 89 Marking area For illuminated versions. The symbol will be included in the hatched area. Marking in M are : on request. A M A M.00 (.) 0.0 (.79).0 (.) R:0.00 (.787 R) R:.00 (. R) 87.00 7.70 (.0) 0.0 (.799) SWITCH PANEL CUTOUT Panel thickness : 0,8 mm to, mm Recommended panel thickness : between mm and, mm.00 mini (.98 min.) MATRIX MOUNTING.00 7.00 mini (.7) (.80 min.) 0.0 (.0).08 0/0. (.80 0/.0).80 0/0. (.9 0/.0) APEM www.apem.com
KL series Locking rocker switches Distinctive features Unlocking actuator Each KL rocker switch includes an unlocking actuator. This actuator must be pressed to activate the protected function of the rocker. Moreover, two frames protect the unlocking actuator from untimely activation. This intuitive and secured ergonomics is patented by APEM. Unlocking actuator Protection frames position versions (electrical functions, and ) Press unlocking actuator to reach the protected position Press opposite part of actuator to leave the protected position position versions (electrical functions 7, 8, 9, R) Press unlocking actuator to reach the protected position Press opposite part of actuator to leave the protected position www.apem.com APEM
KL series Locking rocker switches Specifications One protected position Patented intuitive ergonomics Wide choice of colours Laser etched symbols Illuminated or nonilluminated ELECTRICAL SPECIFICATIONS Currrent/voltage rating with resistive load : Silver contacts (A) : A VDC, 00.000 cycles 0A VDC, 0.000 cycles (terminals. x 0.8 only) Gold plated contacts (D) : 0mA V, 0.000 cycles Initial contact resistance : 0 m max. Insulation resistance :.000 M min. at 00VDC Dielectric strength :.000 Vrms 0 Hz min. between terminals Mechanical life : 0.000 cycles min. MATERIALS Case : PA Actuator and unlocking actuator : AS ezel : PA Terminals : brass, silver plated Contacts : silver (A) or silver, gold plated (D) Contact roller : brass, nickel plated ENVIRONMENTAL SPECIFICATIONS Degree of protection of sealed versions : frontal sealing to IP8 according to IEC 09 (submersion under meter of water for more than 0 minutes) Salt spray resistance : 9 hours according to IEC, test f Operating temperature : 0 C to 8 C SEALING Sealing is optional. To order a sealed product, complete the appropriate box of ordering format on the following pages..0 (.80) DIMENSIONS.00 (.9) 7.00 (.9) Flat seal.0 (.98).00 (.7).0 (.09) 0.00 Max (.99 Max) Dimensions : First dimensions are in mm while inches are shown as bracketed numbers..00 (.98).00 (.) U8 Tolerance : The general tolerance for dimensions in this brochure is ± 0, (.0). Overall dimension tolerance is ± 0, (.00). 7.00 (.80) CKL9DTA Packaging unit : 0 pieces Dimensions, specifications and data shown in this brochure are subject to change without notice. APEM www.apem.com
KL series Locking rocker switches Selection guide To order a complete product, fill in all the boxes of the following order guide. CASE LEDS KL Side SERIES Electrical functions Contacts Sealing LEDS Wiring Poles Single pole Double pole ON OFF ON ON ON R ON ON MOM MOM ON ON ON 7 MOM OFF MOM 8 ON OFF MOM 9 ON OFF ON Terminals A D Screw 0 terminals with barrier Solder lug/quickconnect terminals with barrier terminals w/o barrier A 0 term. with barrier 0 term. w/o barrier C 0 terminals for use with connector U9 Quickconnect,x0,8 terminals with barrier Silver Gold plated X K No Yes Terminals (continued) Quickconnect,x0,8 terminals w/o barrier D 0 term. with barrier E 0 term. w/o barrier F 0 term. for use with connector U9 Quickconnect,8x0,8 G 0 term. with barrier H 0 term. w/o barrier J 0 terminals for use with connector U8 X A C M R D E F N S J K L P T None LED V red LED V green LED V yellow LED V blue LED V white LED V red LED V green LED V yellow LED V blue LED V white LED V red LED V green LED V yellow LED V blue LED V white See diagrams page 8. ACTUATOR ACTUATOR MARKING Area A Area Type For nonillum. application For illuminated application Rocker colour lue / Dark blue lack Green Grey Yellow Red 7 Ivory 9 Orange Unlocking actuator colour lue / Dark blue lack Green Grey Yellow Red 7 Ivory 9 Orange N Orientation ON OFF Symbols : see page. Accessories : see page. Symbols A Marking colour Illuminated models lank White Nonilluminated lue lack Green Grey Yellow Red 7 White 9 Orange NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information. www.apem.com APEM
KL series Locking rocker switches Case CASE LEDS MODEL STRUCTURE Contact area ottom view Contact & LED area Single pole Double pole KL KL ON OFF KL* ON ON ON KLR* ON ON MOM KL KL MOM ON KL KL ON ON KL7 KL7 MOM OFF MOM KL8 KL8 ON OFF MOM KL9 KL9 ON OFF ON 0 8 LED area * Function : single pole in double pole case 0 terminal version terminal version 9 7 ELECTRICAL FUNCTIONS AND CONNECTIONS In the tables below, terminal connections as viewed from bottom of switch. Only the contact area is represented. For single pole models, only terminals, and are to be considered (not,, ). x = w/o terminal o = with terminal = momentary positions positions Press unlocking actuator to unlock. CKLFUNA CKLFUNA Function * KLKL Function 7 KL7KL7 Functionn KL KL Function 8 KL8KL8 Function KLKL Function 9 KL9KL9 * Function Only available for terminal versions. Illuminated versions only available with A wiring. Function KL Function R KLR APEM www.apem.com
KL series Locking rocker switches Case TERMINALS CASE LEDS Screw Solder lug / quickconnect Normalized quickconnect,x0,8 Normalized quickconnect,8x0,8 Ø.00x0.0 SI (.8DIAx0.0 IS) Ø.0 (.DIA) ø.0 (.09DIA) Ø.0 (.07DIA). (.) 0.80 (.0).0 (.77).x0.80 (.x.0).x0.80 (.0x.0).80x0.80 (.0x.0) 0 term. with barrier terminals with barrier terminals w/o barrier A 0 terminals with barrier C 0 terminals w/o barrier 0 terminals for use with connector U9 terminals with barrier terminals w/o barrier D 0 terminals with barrier E F 0 terminals w/o barrier 0 terminals for use with connector U9 G H J 0 terminals with barrier 0 terminals w/o barrier 0 terminals for use with connector U8 Terminals are marked on the case. The drawings show the maximum possible number of terminals..0 (.) 9.0 (.8).8.0 (.9) (.).8 7.0 (.0) (.80) terminal version 0 terminal version CKLCOA CONTACT MATERIALS CASE LEDS A D Silver Silver, gold plated www.apem.com APEM
KL series Locking rocker switches Case LEDs SEALING CASE LEDS X K No sealing IP8 (switch assembled on panel) Optional seal (K version) Ultrasonic welding of frame to case is standard on all versions. The ultrasonic welding and the optional panel seal prevent water and dust from introducing into the switch housing. Optional seal (K version) The product shall be installed professionally. Test conditions available on request. LEDS CASE LEDS Side Complete enlarged box with one of the codes listed below. X Without LED Red Green Yellow lue White VDC A C M R VDC D E F N S VDC J K L P T 7 8 9 0 7 9 8 0 LED consumption : 0mA @ nominal voltage ( C) Other illumination solutions : on request. Side APEM www.apem.com 7
KL series Locking rocker switches Case LED WIRING CASE LED The LED wiring diagram is shown on the case. For terminal versions LED connected to the load A (standard) C E F Note : If not available, terminals are added to connect the LED. For 0 terminal versions Independent LED or integrated functions 8 7 0 9 To have independent LED. G (standard) R 8 7 R 0 9 To obtain symbol illumination levels (night illumination when OFF and higher illumination when ON). Dotted line = external wiring, continuous line = internal wiring H Available in Single Pole only, with H and J quickconnect terminals. 8 7 To have a polarity inversion (typical application : fan motor). 0 9 Dotted line = internal wiring, continuous line = internal wiring I Power supply betweeen and Load between and or and. Available with H and J quickconnect terminals. Please contact us for other wiring solutions. 8 www.apem.com APEM
KL series Locking rocker switches Actuator Marking ACTUATOR TYPE ACTUATOR For nonilluminated application For illuminated application ROCKER COLOUR ACTUATOR Code Colour Code Colour lue Green / Dark blue Grey lack Yellow Code Colour Red 7 Ivory 9 Orange Note : colour 7 not available on illuminated versions UNLOCKING ACTUATOR COLOUR ACTUATOR Code Colour Code Colour Code Colour lue Green Red / Dark blue Grey 7 Ivory lack Yellow 9 Orange MARKING ORIENTATION If no marking required, leave box blank. ACTUATOR MARKING ON OFF N Other orientations : on request APEM www.apem.com 9
KL series Locking rocker switches Marking Mounting SYMOLS ACTUATOR MARKING Available symbols : see page. A Laser etching resistance Water and petrol resistant acccording to EN08 Tear resistant (crosscut test) according to NF ISO 09 : class 0 UV resistant according to ISO 89 A Marking area The symbol will be included in the hatched area..0 (.09).0 (.0).90 (.).0 (.09).0 (.0).90 (.).0 (.).70 (.9).70 (.9).00 (.).00 (.) For illuminated versions For nonilluminated versions MARKING COLOUR ACTUATOR MARKING Illuminated models (laser etching) lank White Nonilluminated models (pad printing) : lue : lack : Green : Grey : Yellow : Red 7 : White 9 : Orange SWITCH PANEL CUTOUT Panel thickness : 0,8 mm to, mm Recommended panel thickness : between mm and, mm.00 mini (.98 min.) MATRIX MOUNTING.00 7.00 mini (.7) (.80 min.) 0.0 (.0).08 0/0. (.80 0/.0).80 0/0. (.9 0/.0) ON ON 0 www.apem.com APEM
KI series Led indicators Specifications Wide choice of bezel colours Wide choice of LEDs Laser etched symbols Long life expectancy ELECTRICAL SPECIFICATIONS Operating voltage : VDC, VDC or VDC Nominal current : 0mA per LED ENVIRONMENTAL SPECIFICATIONS Degree of protection of sealed versions : frontal sealing to IP8 according to IEC 09 (submersion under meter of water for more than 0 minutes) Salt spray resistance : 9 hours according to IEC, test f Operating temperature : 0 C to 8 C MATERIALS Case : AS ezel : AS Terminals : brass, silver plated SEALING Sealing is optional. To order a sealed product, complete the appropriate box of ordering format on the following pages. DIMENSIONS.0 (.8) Flat seal.0 (.98).00 (.7).00 (.) U8 0.00 Max (.99 Max) Dimensions : First dimensions are in mm while inches are shown as bracketed numbers..00 (.98) Tolerance : The general tolerance for dimensions in this brochure is ± 0, (.0). Overall dimension tolerance is ± 0, (.00)..80 (.8) Packaging unit : 0 pieces Dimensions, specifications and data shown in this brochure are subject to change without notice. APEM www.apem.com
KI series LED indicators Selection guide KI Side A Side M Side Side A Side M Side SERIES Colours lue / Dark blue lack Green Grey Yellow Red 9 Orange LEDS X None A LED V red LED V green C LED V yellow M LED V blue R LED V white D LED V red E LED V green F LED V yellow N LED V blue S LED V white J LED V red K LED V green L LED V yellow P LED V blue T LED V white DC voltage standard X S Type of illumination Standard Super bright N O S Marking orientation ON OFF ON ON OFF OFF Symbols A M X K Terminals with barrier Sealing No Yes C Solder lug / quickconnect F Quickconnect, J Quickconnect,8 E OFF ON On request : 8VDC voltage AC voltage new design Symbols : see page. Accessories : see page. NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information. www.apem.com APEM
KI series Led indicators Case LEDs Marking EZEL COLOUR KI Code Colour Code Colour lue Grey / Dark blue Yellow lack Green 9 Red Orange LEDS Side A Side M Side Complete each enlarged box with one of the codes listed below. X Without LED Side A Red Green Yellow lue White VDC A C M R VDC D E F N S VDC J K L P T Side M LED consumption : 0mA @ nominal voltage ( C) Other illumination solutions : on request. Side TYPE OF ILLUMINATION X S Standard Super bright MARKING ORIENTATION If no marking required, leave box blank. Other orientations : on request ON OFF ON OFF OFF ON OFF ON N O S E APEM www.apem.com
KI series LED indicators Marking Terminals SYMOLS Available symbols : see page. Marking colour White (laser etching) Laser etching resistance Water and petrol resistant acccording to EN08 Tear resistant (crosscut test) according to NF ISO 09 : class 0 UV resistant according to ISO 89 Marking area The symbol will be included in the hatched area. A M A M 0.0 (.) 8.0 (.).0 (.) 0.0 (.799).0 (.) TERMINALS (WITH ARRIER) Solder lug / quickconnect Normalized quickconnect,x0,8 Normalized quickconnect,8x0,8 Ø.0 (.DIA) ø.0 (.09DIA) Ø.0 (.07DIA).0 (.77).x0.80 (.x.0).x0.80 (.0x.0).80x0.80 (.0x.0) C 0 terminals for use with connector U9 F 0 terminals for use with connector U9 J 0 terminals for use with connector U8 Terminals are marked on the case. 7.0 (.80) 9.0 (.8) www.apem.com APEM
KI series Led indicators Sealing Mounting SEALING X K No sealing IP8 (switch assembled on panel) Ultrasonic welding of frame to case is standard on all versions. The ultrasonic welding and the optional panel seal prevent water and dust from introducing into the switch housing. Optional seal (K version) The product shall be installed professionally. Test conditions available on request. SWITCH PANEL CUTOUT Panel thickness : 0,8 mm to, mm Recommended panel thickness : between mm and, mm.00 mini (.98 min.) MATRIX MOUNTING.00 7.00 mini (.7) (.80 min.) 0.0 (.0).08 0/0. (.80 0/.0).80 0/0. (.9 0/.0) ON OFF APEM www.apem.com
KG series Power rocker switches Distinctive features and specifications Protected rocker Illuminated or nonilluminated VDE (EN 08) approved Sealed to IP ELECTRICAL SPECIFICATIONS Currrent/voltage rating : functions (ONOFF) and (ONON) : A VDC, 0A VDC, A 0VAC max., 0mA VDC min. functions ( ON ON ON) and R (ON ON MOM) : 8A VDC, A VDC, 8A 0VAC max. other functions : 0A VDC, 8A VDC, 0A 0VAC max. VDE approved ratings : ()A 0VAC, T8/ C Initial contact resistance : 0 m max. at A VDC Insulation resistance :.000 M min. at 00VDC Dielectric strength :.000 Vrms 0 Hz min. between terminals Electrical life : 0.000 cycles min. Mechanical life : position models : 00.000 cycles min. position models : 0.000 cycles min. ENVIRONMENTAL SPECIFICATIONS Degree of protection : IP Shock resistance : 00 g according to IEC, test c Vibration resistance : 000 Hz 0 g according to IEC, test d Salt spray resistance : 9 hours according to IEC, test f Operating temperature : position models : 0 C to 8 C position models : 0 C to C MATERIALS Case : thermoplastic UL9V0 Terminals : brass, silver plated Contacts : silver grain Contact roller : brass, nickel plated EN 08 AGENCY APPROVAL Availability : double pole models, functions ONOFF and ONON. Marking : to order switches marked VDE, add VDE at the end of model number. MATRIX MOUNTING.00 mini. (.98 min.).00 9.00 mini. (.7) (.99 min.).0 (.80) Dimensions : First dimensions are in mm while inches are shown as bracketed numbers. Tolerance : The general tolerance for dimensions in this brochure is ± 0, (.0). Overall dimension tolerance is ± 0, (.00). Packaging unit : 0 pieces Dimensions, specifications and data shown in this brochure are subject to change without notice. www.apem.com APEM
KG series Power rocker switches Case.08 (.80) PANEL CUTOUT Panel thickness : 0,8 mm to, mm Recommended thickness : between mm and, mm.80 (.9) CASE LAMPS ROCKER LENS MARKING MODEL STRUCTURE Flat seal.0 (.9).00 (.) Single pole Double pole KG KG ON OFF KG* ON ON ON KGR* ON ON MOM KG KG MOM ON KG KG ON ON KG7 KG7 MOM OFF MOM KG8 KG8 ON OFF MOM KG9 KG9 ON OFF ON 0.0 (.).0 (.9).00 (.7).8 (.9). (.7).70 (.70) 0.00 (.787) 8.0 (.909) * Function : single pole in double pole case TERMINALS Side A. (.) Ø.00x0.0 SI (.8DIAx0.0 IS) 0.80 (.0).0 (.77) Ø.0 (.DIA).x0.80 (.x.0) Screw Solder lug / quickconnect Quickconnect ø.0 (.09DIA).x0.80 (.0x.0) Terminals to are marked on the case. Side A : terminals and Side : terminals and Side CONTACT MATERIALS A Silver grain Functions ONOFF and ONON : A VDC, 0A VDC, A 0VAC max. 0mA VDC min. Other functions : 0A VDC, 8A VDC, 0A 0VAC max. APEM www.apem.com 7
EZEL KG series Power rocker switches Lamps lack, sealed to IP LAMPS Side A Side Complete each enlarged box with one of the codes listed below. X A C D E F G H I Without lamp V LED red V LED green V LED yellow V LED red V LED green V LED yellow 8V LED red 8V LED green 8V LED yellow J K L M N O P R S T V LED red V LED green V LED yellow Neon V Neon 0V Filament V Filament V Filament V Fluorescent 0V Fluorescent 0V Side A Side LAMP WIRING The lamp wiring diagram is shown on the case. A (standard) C Note : If not available, terminals are added to connect the LED. D for function (onoff) with LED on side A E F To order case only (without rocker), finish your order number with the lamp wiring code. 8 www.apem.com APEM
KG series Power rocker switches Rocker Lenses ROCKER COLOUR lue / Dark blue lack Green Grey 7 9 Yellow Red Ivory Orange ROCKER SHAPE Full rocker Opening on side A Opening on side Opening on sides A and Other rocker shapes on customer specifications : on request. To order rocker only (without case), begin the order number with code KGR, then follow the order format from rocker colour until the end of the options. LENS COLOUR Side A Side Complete each enlarged box with one of the codes listed below. X 9 T No lens lue * Green * Red Orange White Translucent Side A Side * lue or green lens recommended with fluorescent lamp. To order lenses only, begin the order number with the codes : KGLA for lens A and KGL for lens, then follow the order format from lens colour until the end of the options. APEM www.apem.com 9
KG series Power rocker switches Marking MARKING If no marking required, leave all boxes blank. Select one option from each of the tables below. MARKING ORIENTATION MARKING METHOD C Hot stamping V H Other orientations : on request SYMOLS A Available symbols : see page. Marking colour White marking for black rockers lack marking for colour rockers Other : on request. A Marking area For illuminated versions. The symbol will be included in the hatched area..00 (.).00 (.).0 (.88) 0 www.apem.com APEM
range Power rocker switches and indicators Symbols Most symbols meet the ISO 7000 standard graphical symbols for use on equipments (code given in bracket in the description). Contact us for symbols not featured in the following tables. Legend scale : KR series : : KL, KG and KI series : depending on space available on the product (see Symbols section at the end of each series). CODE SYMOL DESCRIPTION XX None CODE SYMOL DESCRIPTION CODE SYMOL DESCRIPTION Emergency first Revolving light aid vehicle () 0 7 Rear ventilator Load tipping (7) 0 8 Heating (07) Loading light (7) 0 9 Door opening Tractor, rearward (0089) 0 0 Windshield demister/defroster (0) Combine, direction of movement (78) 0 Windshield wiper (008) 7 Use no forks (0) 0 Windshield washer (0088) 8 Transmission () 07 Stop Ventilator fan (0089) 9 Working spot light () 08 Motion Side mirror defroster 0 Engine (0) 09 Up motion Restarting pump Horn (0) 0 Down motion Front fog lights (0) Lock () Hot 7 Rear fog lights (0) Taxi sign light () Cold 8 Propulsion system trim Working light (0) Hazard warning (008) 9 eacon () Working light symmetric (0) Traveller lighting 0 Anchor Driver lighting ( Electric motor (00) 7 APEM www.apem.com
K range Power rocker switches and indicators Symbols Most symbols meet the ISO 7000 standard graphical symbols for use on equipments (code given in bracket in the description). Contact us for symbols not featured in the following tables. Legend scale : KR series : : KL, KG and KI series : depending on space available on the product (see Symbols section at the end of each series). CODE SYMOL DESCRIPTION CODE SYMOL DESCRIPTION CODE SYMOL DESCRIPTION 8 All wheel drive Indicator 80 Front windshield heating 9 Differential lock () rake release 8 Aus 0 aggage room left door 8 Radiator fan 7 aggage room right door 8 Remove retarder 8 Power blinds 8 Restricted speed 9 Engine idle control 8 Preheater Rear window wiper (0097) 70 Cruise res/set 8 AS detection Rear window washer (0099) 7 Driver windows up/down 87 ECAS detection Lower load () 7 Middle door opening 88 Engine stop 7 Cab lock (0) 7 Front door opening 89 Cruise res/cancel 8 Extraction 7 Lighting in baggage room 90 ECAS reset 9 Pumping in 7 Cruise on/off 9 Driver windows heating 0 Rear PTO (7) 7 TV 9 Cruise set Front PTO 77 Pump 9 Air bag up/down Rockshaft down 78 Toilet 9 Read lighting Rockshaft up 79 Toilet decontamination 9 Lighting main switch www.apem.com APEM
K range Power rocker switches and indicators Symbols Most symbols meet the ISO 7000 standard graphical symbols for use on equipments (code given in bracket in the description). Contact us for symbols not featured in the following tables. Legend scale : KR series : : KL, KG and KI series : depending on space available on the product (see Symbols section at the end of each series). CODE SYMOL DESCRIPTION CODE SYMOL DESCRIPTION CODE SYMOL DESCRIPTION 9 Heating using water AD AV 97 Low beam AE AW 98 Position lights AF AY 99 Diesel acceleration AG attery charging condition (07) AZ A Manual mode AH Turn signals (008) A Clockwise cabin rotation AJ High beam (008) A Anticlockwise cabin rotation AK Differential lock, bogie (00) A AL rushing with a rotating brush (0070) A AM Differential lock, transfer case x (7) A Parking brake AN Loader bucket, float () A7 AP Loader bucket (7) A8 AQ Rear window washer & wiper (0098) A9 AR Header Header drive (79) AA AS Excavator/backhoe boom side shift (09) A AT Chemical water treatment (8) AC AU Grapple skidder, single funct boom (7) APEM www.apem.com
K range Power rocker switches and indicators Accessories for KR, KL and KI series MOUNTING PANEL END MOUNTING PANEL MIDDLE SINGLE MOUNTING PANEL 9. (.) U U MOUNTING PANEL CUTOUT For element U7 For elements U For elements (xu x U).00 0/0.0 (.98 0/.008).00 0/0.0 77.0 0/0.0 (.008 0/.008) (.0 0/.008) 8.0 0/0.0 (.898 0/.008) 8.0 0/0.0 (.898 0/.008) 8.0 0/0.0 (.898 0/.008).00 (.0).00 (.0).00 (.0).80 (.0).0 (.0).80.0 (.0) (.0). (.0).80.0 (.0) (.0). (.70) U7 Recommended panel thickness :,0 mm,80 mm,0 mm,0 mm,0 mm mm,80 mm For additional elements, add,0 mm (.09) ACTUATOR REMOVING TOOL U0 tools are supplied EXTRACT ACTUATOR (KR ONLY) Allows the extraction of the rocker / rocker support assembly. Place the claws under the support and push as indicated by the arrow. EXTRACT ROCKER (KR ONLY) Allows to separate the rocker from its support. Insert the tool between rocker and support as indicated by the arrrow. Pull out the tool in the opposite direction. EXTRACT SWITCH (KR, KL AND KI) Allows to extract switch from panel mounting units. tools are necessary. Insert the tools between switch and panel mounting units from the rear to compress the snapin device. Pull off switch manually. www.apem.com APEM
K range Power rocker switches and indicators Accessories for KR, KL and KI series CONNECTORS Standard colour : black. Other colours : on request. Connectors cannot be combined with wiring types H and I. U0 U8 U9 terminal version For use with terminals type,, or., (/) tabs to be fitted by the user (example : AMP/Tyco 000). Can be used for the KG series. 0 terminal version For use with terminals type H or J.,8 (.0) tabs to be fitted by the user (example : AMP/Tyco 097779). 0 terminal version For use with terminals type, C, E or F., (/) tabs to be fitted by the user (example : AMP/Tyco 000)..00 (.77).0 (.).0 (.) ➀ pokayoke.00 (.98).00 (.) 0.80 (.89).0 (.).00.0 (.) (.9) 0.0 (.80) 9.0 (.7).0 (.9).00 (.) 0.80 (.89) 9.0 (.7) U0 U8 U9 HOLE PLUGS Usefull for future extensions..0 (.8).0 (.09) Code Colour Code Colour U7 lue U7 Grey U7/ Dark blue U7 Yellow U7 U7 lack Green U7 U77 Red Ivory U79 Orange Recommended panel thickness :,0 mm to mm.00 (.8).0 0.80 (.7) (.89).80 (.8).00 (.98) Connectors can be hanged on specific hole plugs. Contact APEM. APEM www.apem.com
APEM, a world of switching capabilities The APEM group is one of the world s largest manufacturers of switches, switch panels and joysticks. APEM designs, develops, manufactures and sells electromechanical components to multiple industrial markets including: instrumentation, medical, security, communications, industrial automation, avionics, military and transport. Other APEM embedded products " I " range of pushbuttons This range consists of several series of IP7 sealed pushbuttons (IP, I, IS, IF, IA) and a large variety of models: round or square, momentary or latching, illuminated or nonilluminated, plastic or metallic, with optional marking. Specific switch panels In addition to the switching function, specific switch panels incorporate several other functions such as illumination by LED, backlighting, EMC protection, sealing, connection, support, mounting... Applications for these products include transport and utility vehicles, agricultural engines and boats. Joysticks APEM also manufactures joysticks for professional applications. Easy to operate, reliable and designed for extremely long service life, APEM joysticks are offered with a wide range of options allowing to satisfy a large variety of requirements. Several series are available, each one based on a different technology: switch joysticks, potentiometer joysticks and contactless joysticks. Addresses of sales subsidiaries and distributors network on www.apem.com K080A