-100 Controller IEC Performance Data (CSA C22.2, UL 508 No. 14 in connection with a short-circuit protection device Catalog No. -100... 25A 40A 63A 90A Maximum Short-Circuit Current 480V [ka] 65 65 42 35 600V [ka] 42 42 18 10 Motor Load, Single-Phase 115V [HP] 2 3 5 7-1/2 200V [HP] 3 5 10 15 230V [HP] 3 7-1/2 10 20 Motor Load, Three-Phase 200V [HP] ~ ~ ~ ~ 230V [HP] 7-1/2 10 20 30 460V [HP] 15 30 40 60 575V [HP] 20 30 60 75 Maximum Rated Current of the Protective Device [A] 2000 IEC Performance Data Catalog No. -100... 25A 40A 63A 90A Switching of Three-Phase Motors AC-2, AC-3 230/240V [kw] 5.5/7.5 10/11 13/20 22/25 400/415V [kw] 7.5/12.5 15/22 25/32 37/45 500V [kw] 11/15 18.5/25 30/40 45/55 690V [kw] 15/22 25/30 37/55 63/75 Motor Load, Single-Phase gg, am, only if I cc >I cu 230/240V [A] ~ ~ ~ ~ 400/415V [A] 160 160 160 160 500V [A] 160 160 160 160 690V [A] 160 160 160 160 Ultimate Short-Circuit Breaking Capacity I cu 230/240V [ka] 100 100 100 100 400/415V [ka] 65 65 65 50 500V [ka] 50 30 30 25 690V [ka] 15 8 8 6 Rated Short-Circuit Breaking Capacity I cs 230/240V [ka] 100 100 100 100 400/415V [ka] 65 50 50 25 500V [ka] 50 25 25 13 690V [ka] 15 8 6 6 37
Series -100 Controller General Data Catalog Number -100 Rated Isolation Voltage IEC, SEV, VDE 0660 690V UL, CSA 600V Rated requency 40...60 Hz Lifespan Mechanical 30,000 operations Electrical 10,000 operations at 63 A 5,000 operations at 90 A Switching requency maximum 20 ops/hr Ambient Temperature Storage -25...+80ºC (-13...176º) Operation -25...+60ºC (-13...140º) Corrosion Resistance C IV (per IEC 68) Resistance to heat and humidity 40ºC, 92%, 56 days Resistance to cyclic heat and humidity 23ºC, 83%/40ºC, 93%, 50 cycles Type of Protection IP20 enclosed state Resistance to Shock [G] 30, 11 ms Resistance to Vibration requency range 10...150 Hz In all directions in testing Rated Thermal Current I th IEC, SEV, VDE 0660 ~ At 40ºC ambient temperature 16...90 A At 60ºC ambient temperature 4 adjustment ranges Rated current I e 16...90 A Rated Impulse Voltage/Pollution Main circuits 6 kv/3 Auxiliary circuits 6 kv/3 Overload Protection Characteristics motor protection per IEC 947 Temperature compensation -25...+60ºC (-4...140º) Phase failure protection differential release Magnetic Release Operating current fixed setting 14 x I e maximum I e maximum = maximum value of adjustment range Power Loss P v At maximum rated current and with switch at rated operating temperature 33 W IEC 947-1/2/4/5; Standards EN 60947; UL 508; CSA 22.2 Approvals CE, CSA, UL Lloyd s Register of Shipping Terminals Terminal Type lexible [mm 2 ] Stranded [mm 2 ] 2.5...35 Breakaway Torque [Nm] Stranded [mm 2 ] 4...50/12...2 Breakaway Torque [lb-in.] 6...10/55...90 Weight 3-pole circuit breaker [g] 1845 (4.10) 38
Series -100 Controller General Data Integrated Short-Circuit Indicator in Catalog Number -100-UA...and -100-AA... Rated Thermal Current I th At 40ºC ambient temperature [A] 2 At 60ºC ambient temperature [A] 2 NEMA Contact Class (UL/CSA-Approval) AC DC Make/Break max. voltage 432 VA72 VA480 A 28 VA28 VA250 V Back-Up use gl, gl [A] 16 24V 110V 230V 400V 500V AC-14 1.5A 1.5A 1.0A 1.0A 0.75A Rated Current 24V 48V 60V 110V ~ DC-13 1.5A 0.5A 0.4A 0.2A ~ Terminals Terminal Type lexible [mm 2 ]/[AWG] 0.75...2.5/No. 18...14 Stranded [mm 2 ]/[AWG] 0.75...2.5/No. 18...14 lexible [mm 2 ]/[AWG] 0.75...2.5/No. 18...14 Stranded [mm 2 ]/[AWG] 0.75...2.5/No. 18...14 Tightening Torque [N m]/[lb in] 1...1.5/8.8...10.3 Weight [g (lb)] 91 (0.21) Operating Voltage Pick-up Drop-out Duty cycle Undervoltage Trip Unit for ront Mounting on Catalog Number -100 0.85...1.1 x Us 0.7...0.35 x Us continuous Control Voltage min. 21V 50 Hz / 24V 60 Hz max. 600V 50 Hz Coil Performance Terminals Terminal Type pick-up drop-out upon inquiry lexible [mm 2 ] / [AWG] 2 x 0.50...2.5 (18...14) Stranded [mm 2 ] / [AWG] 2 x 0.75...2.5 (18...14) Tightening Torque [Nm] / [lb-in] 1.2...1.5 (10.6...13.3) Weight [g (lb)] 94 (0.21) 39
-100 Controller Cut-Off Current -100 Controller Maximum Cut-Off Current Rated Operating Voltage 415V Maximum orward Energy Rated Operating Voltage 415V Protection of PVC Insulated Leads Against Overload and During Short-Circuit Protected Minimum Copper Cross-Section at 400V 50 Hz Catalog Number 10 mm 2 6 mm 2 4 mm 2 2.5 mm 2 1.5 mm 2 1 mm 2 0.75 mm 2-100-25A ~ ~ ~ -100-40A ~ ~ ~ ~ -100-63A ~ ~ ~ ~ ~ -100-90A ~ ~ ~ ~ ~ ~ As per IEC 364 and CENELEC coordination documents 384-3 and 384-3. In the Bulletin -100 Motor Protector, overload protection is achieved by means of the adjustable thermal releases. The maximum possible tripping current is substantially lower than in fused overload protection. Short-circuit protection is provided by the non-adjustable magnetic release which is capable of opening the main contacts very quickly. The short total breaking time limits temperature rise in the lead to a minimum in the event of a short-circuit. 40
-100 Controller Time-Current Characteristic -100 Manual Motor Starter/Protector 1. Thermal Release Operating Current The adjustable current-dependent delayed bimetal release protects motors against overload. The characteristic shows the mean at 20 C ambient temperature starting from the cold state. In equipment at operating temperature, release time is less than or equal to release time from the cold state. The precise routine test guarantees motor protection even when a phase is interrupted. Motor protection in protection type EExe: Pursuant to VDE 0165/83, the release time of the cold overload release must be less than the allowed locked-rotor time t E of the motor. The specific tripping characteristics must be available at the operating site. If necessary, they can be ordered from the appropriate Sprecher + Schuh Sales Office. or new systems, protection equipment must be provided for motors in accordance with VDE 0165/83, section 6.1.4.3.3. Such protection equipment must ensure motor protection even in the event of a phase failure. 2. Operating Current for Magnetic Releases Electromagnetic instantaneous releases react at a set tripping current. At the upper thermal release setting, this tripping current is 11 times or 14 times the set current at a lower setting. Current To Be Set Thermal releases meet the requirements for a thermal release for a starter in accordance with IEC 947. If a different value is specified (such as reduced I e in motors with a coolant temperature higher than 40 C or a site altitude >2000 m above M.S.L.), the rated operating current I e must be adjusted. Note: In certain applications such as in multi-speed motors or star delta starters for heavy duty start and/or reduced motor lead cross-sections, the 100 devices are used only as short-circuit protection, while overload protection is accomplished by thermal overload relays. The 100 motor protector must be set for a 20% higher current so that only the downstream thermal overload relays trip in the event of an overload. 41
Dimensions -100 Controller -100 Controller Dimensions are in millimeters (inches). Dimensions not intended for manufacturing purposes. 42
Notes 43