MM Tubular K-Member, (Mm5KM-7)

Similar documents
MM Caster Camber Plates, (Mm6CC-10)

MM Caster/Camber Plates, (MMCC7989)

Adjustable Tie-rod Ends (Mm5TR-1)

2011+ Adjustable Tie-rod Ends (Mm5TR-2)

Cobra IRS Aluminum Differential Bushings (MMIRSB-40.2)

MM Caster/Camber Plates, (Mm5CC-7)

Coil-Over Kit, MMD-RC1xxxx Shock (MMCO-22)

Coil-Over Kit, MMD-RC1xxxx Shock (MMCO-23)

IRS Racing Brake Kit (MMBAK-15, -16)

3430 Sacramento Dr., Unit D San Luis Obispo, CA Telephone: 805/ Fax: 805/

4.6L Oil Filter Relocation Kit, (OC-7)

Hybrid Steering Shaft, SN95 Rack in Fox Chassis (MMST-13)

MM Brake Hose Kit (MMBK13R)

MM K-Member, chassis with 5.0L engine (MMKM-1.1)

2. Remove front wheels.

MM Brake Line Kit (MMBK14R)

Coil-Over Kit, MMD-RC0xxxx Shock (MMCO-20)

MM Rear Coil-Over Kit - Koni Single and Double Adjustable Shocks (MMCO-5)

2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill 1-3/4" Hole saw 2" Hole saw

MM Rear Coil-Over Kit - Bilstein Shocks (MMCO-3)

Standard Duty Oil Filter Relocation Kit (OC-8)

Severe Duty Oil Filter Relocation Kit (OC-9)

MM K-Member, chassis with 4.6 engine (MMKM-2.1)

Front Coil-Over Kit, MMD-FCxxxxx Series (MMCO-24)

Manual Brake Conversion Kit, (MMBAK-13)

MM Brake Line Kit for Fox-IRS Swap (MMBAK-21)

US Patent You will find many features that set our Caster/Camber Plates apart from the rest.

2010 Current Ford Raptor Lower Control Arm Installation Instructions

MM Adjustable IRS Tie-Rod (MMIRSTR-2)

SPECIAL TOOLS REQUIRED:

MM IRS Coil-Over Kit - Bilstein/MM Shocks (MMCO-4)

»Product» Safety Warning

2005+ Drag Race Roll Bar (Mm5RB-20)

Drag Race Roll Bar (MMRB-6, -7)

Team Z Motorsports. K-Member installation instructions

Roll Bar (MMRB-1.1 to 1.7)

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION

MM Panhard Bar, Mustang (MMPBA)

Standard Duty Oil Filter Relocation Kit (OC-3)

1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST MUSTANG LONG TUBE HEADERS (M30000)

MM K-Member, chassis w/4.6l engine & Hellion Turbo Kit (MMKM-3.1)

Convertible MM Roll Bar (MMRB-10.1 to -10.7)

AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE

63162K 2015 Chevrolet Colorado 4WD Leveling Kit w/ 1 Rear Lift Kit

Installation Instructions

»Product» Safety Warning

1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST MUSTANG GT LONG TUBE HEADERS (M30000)

1 M-3000-H4 F150 4X4 Lowering Kit

Ford F150/Raptor & F150 Lower Control Arm Installation Instructions

B5 A4 1.8t Front Mount Intercooler Install Instructions

MM Heavy Duty Torque-arm (MMTA-3 & -4) Engine Torque Table 4.56: : :

'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS

2005-Pres. Ford Mustang Camber Plate Installation Instructions:

INSTALLATION INSTRUCTIONS

Installation Instructions. 6 Basic System FTS21060BK / FTS21061BK / FTS21042BK GM 2WD C1500 P/U ONLY

AEV30213AH Last Updated: 04/28/17. jk wrangler dualsport sc suspension INSTALLATION GUIDE

RANGER 900 POWER STEERING KIT

PARTS LIST INCLUDED IN KIT TORQUE SPECIFICATIONS PRODUCT SAFETY LABEL MUST BE INSTALLED INSIDE CAB IN PLAIN VIEW OF ALL OCCUPANTS.

INSTRUCTION S G-Comp Front Suspension: Chevy Nova Speedway Motors, Inc. 2017

99-04 GT. Hellion Power Systems Mustang GT Kit Instructions

Installation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER Mustang w/5-speed Manual Transmission (GT only)

INSTALLATION INSTRUCTIONS FOR 2016 TOYOTA TACOMA 4 X 4 AND PRE RUNNER 3 SUSPENSION LIFT KIT PART NUMBER

REVTEK SUSPENSION RECOMMENDS USING RED LOCTITE ON ALL FASTENERS UNLESS OTHERWISE NOTED. ALSO, HAVE THE FRONT END ALIGNMENT CHECKED AFTER INSTALLATION

Alignment Spec. Power Rack & Pinion: 5 degrees positive Camber 0 degrees Toe-In 1/32

NOTICE- THIS K-MEMBER REQUIRES THE USE OF COIL OVER SUSPENSION. K-MEMBER WILL NOT WORK WITH FACTORY STYLE SPRINGS.

Page1. ISF Stainless Steel Headers // Part# HDR-004

4, 6 Suspension System. Ford F250/350 4WD Part#: ,

Part # Camber Caster Plates Ford Mustang All Ford Mustang GT500

INSTRUCTION S G-Comp Front Suspension: Chevy Camaro Speedway Motors, Inc Kit Contents:

FULL LENGTH HEADERS/ CATTED HEAD PIPES

MM010 6TH GEN CAMARO TUBULAR MOTOR MOUNTS

Roll Bar (MMRB-6.1 to -6.7)

MM Standard Torque-arm (MMTA-1 & -2) Engine Torque Table. Differential Ratio. Standard TA Max. Engine Torque (lb-ft)

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3

»Product» Safety Warning

LML 3 Y-Bridge Kit or High Flow Intake Bundle Package

M-Force E36 Camber Plate Installation

It is strongly recommended that this kit be installed by an authorized Polaris dealer.

Installations Instructions for Maier Racing Front Coilover Kit MS Ford Mustang

Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.

Read and understand all instructions and warnings prior to installation of product and operation of vehicle.

EPS LH DRIVE KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev 01 04/16 Page 1 of 11. E2, E4, E6, and el XD

MAZDASPEED3 Intercooler Instructions

2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #

Chevy Nova Pro-Touring Front Suspension Installation Instructions

Performance Air Intake, 2015+

AEV30207AA Last Updated: 2/14/ Dualsport xt suspension INSTALLATION GUIDE

INSTALLATION GUIDE TCP RCKM-01

Tuned Length Headers. Special Tools Required: Install Time: Difficulty: Follow these instructions carefully to ensure correct fitment and operation.

Chrysler A-Body Tubular A-Arms Installation Instructions A-ARM INSTALLATION

INSTALLATION INSTRUCTION 88581

J&M CASTER/CAMBER PLATE INSTALLATION INSTRUCTIONS (#24213) Hardware:

BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt)

Installation Instructions Mustang Level 2 Coilover. Part # Mustang Level 2 CoilOver System.

SCION tc STRUT TIE BAR Preparation

LOW, MID, HIGH RISE PRO-TAPER HANDLEBAR WITH HEATED GRIPS KIT

INSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER 2018 FORD F150

»Product» Safety Warning

»Product» Safety Warning

Installation Procedure GR40 S197 SLA Front Suspension System (Does not include Aluminum Spindle and Hub Instructions)

Transcription:

3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Tubular K-Member, 2005-14 (Mm5KM-7) This Kit Contains Congratulations on purchasing Maximum Motorsports 2005-14 Mustang K-Member. Read all instructions before beginning work. Following instructions in the proper sequence will ensure the best and easiest installation. Required Tools Standard assortment of hand tools Floor Jack & 4 jack stands 1/2 Torque Wrench Description QTY Alignment Pin 2 Aluminum Frame Rail Block, Driver 1 Aluminum Frame Rail Block, Passenger 1 Engine Mount Bracket, Stock-1 2 Engine Mount Bracket, Stock-2 2 Flange Nut, M12-1.5 2 Flange Nut, M14-2.0 3 Flange Bolt, M12-1.75 x 35mm 6 Hex Bolt, M10-1.5 x 25mm 16 Socket Head Cap Screw, M8-1.25 x 20mm 2 3/8 G8 Washer 16 Large Flat Washer 1 Hose Clamp 1 Zip Ties 2 Blue Loctite 1 MM K-member 1 Installation Instructions 1 Required Supplemental Items Mm5TR-2 Bumpsteer Kit MMT-11 Engine Support Brace or an engine hoist Mm5KM-9 Stock Crossmember Brace Adapter Kit (for 2011-14 vehicles that want to retain the OEM k-member to stock radiator core support brace) Installation Time Shop: 3.5 Hours Home Mechanic: 8 Hours Supplemental Installation Notes Alignment is required after installation Measuring and adjusting bumpsteer is recommended but not required Mm5KM-7r2.indd 1

Component Identification 2 Mm5KM-7r2.indd

Installation 5. Support the engine securely from above. The MMT-11 Engine Support Beam can be used to support the engine. 1. Support the car level on 4 jack stands. Place the jack stands underneath the rocker panel pinch welds. WARNING: The engine must be properly supported from above before proceeding. Do NOT use a floor jack to hold the engine up from below, as it can move and allow the engine to fall. NOTE: The bottom of the rocker panel pinch welds should be at least 18 off the ground to allow easy removal of the k-member. 6. (2011-14 ONLY) Remove the 8 rear-most splitter screws using a 7mm nut driver. WARNING: Do NOT lift the car up from anywhere other than the rocker panel pinch welds, or damage will occur. 2. Remove the front wheels. 3. Disconnect the negative terminal of the battery. WARNING: Permanent damage to the electric steering rack control module can occur if it is removed while the battery is still connected. 4. Remove the two upper engine mount nuts using a deep 15mm socket (one on each side of car). 7. (2011-14 ONLY) Remove the 6 crossmember brace bolts and 2 nuts using a 15mm socket. Gently pull down the back edge of the splitter to gain access to the front mounting bolts. Mm5KM-7r2.indd 3

11. (Electric Rack ONLY) Disconnect both of the wiring harness plugs from the driver side of the steering rack. See the pictures below for proper removal. Each harness plug has two locking features to keep them connected to the steering rack. 8. Remove the outer steering tie-rod nuts from the spindle using a 18mm socket. (one on each spindle). 9. Remove the outer steering tie-rods from the spindle arms. If a bumpsteer kit is already installed, remove the rod-end from the tapered stud. 10. Remove the control arm ball joint pinch bolts using an 18mm socket and 15mm wrench. 4 Mm5KM-7r2.indd

12. (Electric Rack ONLY) Disconnect the harness strain relief tab on the forward, outboard corner of the power steering rack control module. 13. (Electric Rack ONLY) With the steering column unlocked, rotate the steering shaft so that the head of the bolt retaining the u-joint to the input shaft is accessible using a socket. 14. (Electric Rack ONLY) Lock the steering column by removing the key from the ignition. WARNING: Do NOT rotate the steering wheel once the rack is removed. 15. (Electric Rack ONLY) Remove the bolt retaining the lower steering shaft u-joint to the steering rack input shaft using a 13mm socket. Stock K-member Removal 21. Remove the four (4) k-member lower frame rail mounting pad bolts using an 18mm socket. NOTE: These bolts require a lot of effort to remove due to the thread retaining compound used. 16. (Electric Rack ONLY) Proceed to the Stock K-member Removal section. 17. (Hydraulic Rack ONLY) Remove the bolt that holds the power steering hose to the center of the k-member. 22. Loosen, but not remove the four (4) k-member upper frame rail mounting nuts using an 18mm socket. 18. (Hydraulic Rack ONLY) With the steering column unlocked, rotate the steering shaft so that the head of the bolt retaining the u-joint to the input shaft is accessible using a socket. 19. (Hydraulic Rack ONLY) Lock the steering column by removing the key from the ignition. WARNING: Do NOT rotate the steering wheel once the rack is removed. 20. (Hydraulic Rack ONLY) Remove the bolt retaining the lower steering shaft u-joint to the steering rack input shaft using a 13mm socket. Mm5KM-7r2.indd 5

23. Support the k-member with a floor jack and remove the nuts loosened in Step 22. 24. (Electric Rack ONLY) Gently lower the k-member to the ground. The spindles may need to be jiggled slightly to remove the control arm ball joints as the k-member is lowered. Stock K-member Disassembly 29. (Electric Rack ONLY) Remove the 3 bolts retaining the steering rack to the stock k-member. Retain the bolts as they will be reused. 25. (Hydraulic Rack ONLY) Lower the k-member, while being careful to not over-stress the attached hydraulic lines, just far enough that the two rack mounting bolts can be accessed. The spindles may need to be jiggled slightly to remove the control arm ball joints as the k-member is lowered. 26. (Hydraulic Rack ONLY) Remove the two rack mounting bolts using an 18mm socket. Retain the bolts as they will be reused. NOTE: The rack mounting bolts will be VERY difficult to remove due to thread retaining compound used. 27. Strap the steering rack to the front swaybar using the provided zip-ties. 30. Remove the 4 bolts holding the engine mounts to the stock k-member using a 13mm socket. Retain the bolts, they will be reused. 28. Safely lower the k-member to the ground. 31. Remove both front control arms from the stock k-member. Use an 18mm socket for the front bolts and a 21mm socket for the two rear nuts. 32. If heat shields are present on the rearward bushing shells of the stock control arms, remove them now. They will not be reused. 6 Mm5KM-7r2.indd

Aluminum Frame Rail Block Preparation 33. Insert one of the provided 8mm socket head caps screws into each of the provided alignment pins and thread them into the tops of the aluminum frame rail blocks. Tighten them to 20 Nm (16 lb-ft). 36. Take 12 of the provided 10mm x 25mm long bolts, with a washer under each head, and apply a drop of Blue Loctite to the first few threads of each bolt. Loosely thread them into the mounting holes for the engine mount adapter plates, but do not tighten. NOTE: The mounting holes are slightly oversized to allow for production tolerances. Torquing the bolts before installing the engine isolators may cause the mounting holes to be misaligned. 34. Lay the two aluminum frame rail blocks adjacent to each other so that the 6 threaded holes are facing you. The alignment pins should be facing up. 35. Locate the 4 engine mount brackets and place them on the aluminum frame rail blocks as shown. The welded on nuts should be oriented downwards. 37. Install the engine isolators onto the aluminum frame rail block assemblies. Loosely thread the factory mounting bolts down, but do not torque. 38. Torque the 10mm bolts installed in Step 36 to 41 Nm (30 lb-ft) and torque the factory engine isolator bolts installed in Step 37 to 55 Nm (41 lb-ft). Mm5KM-7r2.indd 7

MM K-member Preparation 39. Bolt the 2-point k-member brace to the k-member using 4 of the provided 10mm x 25mm long bolts with a washer under the head of each bolt. The bottom of the brace should be flush with the bottom of the k-member. NOTE: If installing the optional Mm5KB2-21 k-member brace with transmission cooling scoop, do so at this time. 43. Reuse the 4 factory nuts removed in Step 23 and loosely thread them onto the 4 upper frame rail mounting bolts so that the aluminum frame rail blocks can still be moved with slight effort. 44. Install the lower frame rail mounting bolts that were removed in Step 21 into the rear mounting pads of the k-member, but do not tighten. 40. Torque the k-member brace bolts to 48 Nm (35 lb-ft). 41. Apply the provided Blue Loctite to the threads of the 6 provided 12mm x 35mm long flange bolts and loosely bolt the aluminum frame rail blocks to the MM K-member so that they can slightly slide around. The corner of the blocks with the large radius faces forwards and outwards. 45. Slide the k-member assembly forward as far as it will go. 46. Set the k-member side-to-side position by aligning the two counter bored holes on the driver side aluminum frame rail mounting block with the edge of the k-member s upper frame rail mounting flange. 47. Torque the upper frame rail mounting nuts to 115 Nm (85 lb-ft). MM K-member Installation 42. Using a floor jack or helper, lift the k-member into position so that the 4 bolts protruding from the upper frame rails slide into the aluminum frame rail blocks. Once near the frame rail, the aluminum frame rail blocks must be moved backand-forth slightly to help position the alignment pins into the locating hole and slot on the frame rails. NOTE: Slide the driver side up into position first, then the passenger side. NOTE: Be sure that the studs on the engine isolators have passed through their mounting holes on the engine. 48. Torque the lower frame rail mounting bolts to 115 Nm (85 lb-ft). 49. Torque the 6 flange bolts installed in Step 41 to 82 Nm (60 lb-ft). 8 Mm5KM-7r2.indd

50. Install the lower control arms into position on the k-member, using the lower set of mounting holes. Reuse the factory hardware to attach the rear pivot bushings to the k-member. 51. Install the lower control arm forward pivot mounting bolts, removed in Step 31, into the lowest control arm mounting holes of the k-member, along with one of the provided 14mm flanged nuts. 61. Reinstall the spindle ball joint bolts/nuts and torque to 103 Nm (73 lb-ft). 62. (Hydraulic Rack ONLY) Use the provided hose clamp to secure the power steering hose relief bracket to the steering rack. Slip the hose clamp through the mounting slot of the bracket, then around the steering rack housing, and firmly tighten. NOTE: Dot not tighten the forward pivot bolts yet. 52. Torque the rear pivot bushing mounting hardware to 185 Nm (136 lb-ft). NOTE: The rear pivot bushing must be torqued first to remove any preload in the rubber bushings. 53. Torque the front pivot bushing mounting hardware to 205 Nm (151 lb-ft). 54. Reinstall the steering rack, making sure to slide the steering shaft u-joint onto the input shaft of the rack. 55. Install the two factory 12mm rack mounting bolts into the steering rack housing and through the mounting bosses on the k-member (removed in Step 26 for hydraulic racks & Step 29 for electric racks). NOTE: These are fine threaded bolts. 56. Use the two provided 12mm-1.5 flange nuts to secure the steering rack mounting bolts. Torque the nuts to 115 Nm (85 lb-ft). 57. (Electric Rack ONLY) Place the provided large flat washer onto the 14mm steering rack mounting bolt and insert from the top of the rack. Use the remaining provided 14mm flanged nut and torque to 115 Nm (85 lb-ft). 58. Reinstall the steering shaft u-joint pinch bolt and torque to 25 Nm (18 lb-ft). 59. (Electric Rack ONLY) Reconnect the two wiring harness plugs and strain relief tab removed in Steps 11 to 12. 60. Insert the control arm ball joints into the spindles. It may be necessary to loosen/remove spindle-to-strut mounting bolts if the control arm cannot be pushed down far enough to engage the ball joint. Mm5KM-7r2.indd 9 63. Install an Mm5TR-2 Bumpsteer Kit. Place the following spacers between the top of the rod end and the bottom of the stud s shoulder: 0.03, 0.24, and 0.48. The remaining spacers must be placed below the rod end. 64. (2011-14 ONLY) If the stock crossmember brace removed in Steps 6 to 7 is being reused, a Mm5KM-9 Crossmember Brace Adapter Bracket kit should be installed at this time. 65. (2011-14 ONLY) Install the 8 rear-most splitter screws removed in Step 6. 66. Lower the engine onto the engine isolators and remove the MMT-11 Engine Support Brace. 67. Reinstall the two upper engine isolator nuts and torque to 63 Nm (46 lb-ft)

68. Reinstall the front wheels and safely lower the vehicle to the ground. 69. Torque to wheels to the factory specifications. 70. Reconnect the battery terminal. 71. Have the vehicle properly aligned. 72. Test drive and enjoy! 10 Mm5KM-7r2.indd