Uniline System FrontespizioUnilineSystem.indd 1 22/11/ :32:41

Uniline ystem

1 Uniline series Uniline series Uniline series description ig. 1 Uniline is a family of ready-to-install linear actuators. They consist of internal ompact Rail roller sliders and steel-reinforced polyurethane belts in a rigid aluminum profile. Longitudinal seals enclose the system. This arrangement provides the best protection for the actuator from soiling and damage. In the series, the fixed bearing rail (T-rail) is mounted horizontally in the aluminum profile. Versions with long (L) or double (D) sliders in one axis are possible. The most important characteristics: ompact design Protected internal linear guides High traversing speeds Grease-free operation possible (depending on the application. or further information, please contact our pplication Engineering department) High versatility Long strokes Versions with long or multiple sliders available in one linear axis Preferred areas of application: Handling and automation Multi-axis gantries Packaging machines utting machines Displaceable panels Painting installations Welding robots pecial machines Technical data: vailable sizes : : 40, 55, 75, 100 Length and stroke tolerances: or strokes <1 m: +0 mm to +10 mm (+0 in to 0.4 in) or strokes >1 m: +0 mm to +15 mm (+0 in to 0.59 in) U-

Uniline ystem The components Extruded profile The anodized 6060 aluminum alloy extrusion used for the profi le of the Rollon Uniline series linear units were designed and manufactured by industry experts to optimize weight while maintaining mechanical strength. (see physical-chemical characteristics below). The dimensional tolerances comply with E 755-9 standard. be achieved. Optimization of the maximum belt width/body dimension ratio enables the following performance characteristics to be achieved: High speed Low noise Low wear Driving belt The Rollon Uniline series linear units use steel reinforced polyurethane drive belts with RPP pitch and parabolic profi les. This belt is ideal due to its high load transmission characteristics, compact size and low noise. Used in conjunction with a backlash-free pulley, smooth alternating motion can arriage The carriage of the Rollon Uniline series linear units are made entirely of anodized aluminum. Each carriage has mounting T-slots for the connection to the moving element (size 40 has threded holes). Rollon offers multiple carriages to accommodate a vast array of applications. General data about aluminum used: L 6060 hemical composition [%] I Mg i e Mn n u Impurites Remainder 0.5-0.60 0.0-0.60 0.0 0.10 0.10 0.10 0.05-0.15 Tab. 1 Physical characteristics Density kg dm oeff. of elasticity k mm oeff. of thermal expansion (0-100 ) 10-6 K Thermal conductivity (0 ) W m. K pecific heat (0-100 ) J kg. K Resistivity Melting point Ω. m. 10-9.7 69 00 880-900 600-655 Tab. U Mechanical characteristics Rm Rp (0) H mm % mm 05 165 10 60-80 Tab. U-

40 40 system 4,5 80 4 M4 threads 15 7,5, lider troke** L J K E ection - G V W V 9 H 8, 16,5 I 1 Uniline series ore diameter * M M * or information on the motor connection bores, see ordering key. ** The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. * E G* H I J K M V W troke** 40 40 51.5 57 4.5 0 6 14 Ø 14,9 5 0. Ø 165 0.5 9 91.5 1900 Tab. 4 * or the position of the T-nuts when using our motor adapter plates, see pg. U-15ff ** Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 9 40L with long slider 4,5 = = 6 M4 threads 7,5 15 n L * The length of the safety stroke is provided on request according to the customer's specifi c requirements. troke* ig. min max n troke* 40L 40 400 n = min + n 10 91.5 1660 Tab. 5 * Maximum stroke for a single-piece guiding rail and a maximum slider plate length max or longer strokes, see tab. 9 40D with double slider L 4,5 80 4 M4 threads lider troke* 7,5 15 * The length of the safety stroke is provided on request according to the customer's specifi c requirements. Ln 4 M4 threads ig. 4 L min L max ** Ln troke* 40D 165 5 1900 Ln = L min + n 5 91.5 1660 Tab. 6 * Maximum stroke for a single-piece guiding rail and a minimum slider plate distance L min ** Maximum distance L max between the centres of slider plates at a stroke of 0 mm or longer strokes, see tab. 9 U-4

Uniline ystem Load ratings, moments and characteristic data 40 Driving belt The driving belt is manufactured from a friction resistant polyurethane and 0ax M x with steel cords for high tensile stress resistance. of belt elt width Weight kg/m M z 40 10RPP5 10 0.041 Tab. 7 elt length (mm) = x L - 168 tandard slider M y 0rad elt length (mm) = x L - n - Long slider elt length (mm) = x L - L n - 168 Double slider ig. 5 [] 0rad [] 0ax [] M x [m] M y [m] M z [m] 40 150 80 00.8 5.6 1.1 40-L 060 1640 600 5.6 to 70 61 to 19 40-D 060 1640 600 5.6 70 to 570 19 to 1558 or the calculation of the allowed moments, please observe pages L-5ff Tab. 8 Technical data tandard belt tension [] 160 Moment at no load [m] 0.14 40 Max. traversing speed [m/s] Max. acceleration [m/s²] 10 U Repeat accuracy 0.1 Linear accuracy 0.8 ompact Rail guiding rail lider type TLV18 18 spec. Moment of inertia Iy [cm 4 ] 1 Moment of inertia Iz [cm 4 ] 1.6 Pitch diameter of pulley [m] 0.0706 Moment of inertia of each pulley [gmm²] 5055 troke per shaft revolution 85 Mass of slider [g] 0 Weight with zero stroke [g] 1459 Weight with 1 m stroke [g] 465 Max. stroke 500 Working temperature from -0 to + 80 Tab. 9 U-5

55 system lider troke** L E G I 1 Uniline series 55, J Y K X ection - V W V H D ore diameter * 8, 16,5 9 M M * or information on the motor connection bores, see ordering key. ** The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. 6 * D E G* H I J K M X Y V W troke** 55 55 71 67.5 5 50.5 7.5.5 15 Ø 4.9 1.5 5.5 Ø 47 00 8 1 0.5 54 108 070 Tab. 10 * or the position of the T-nuts when using our motor adapter plates, see pg. U-15ff ** Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 15 55L with long slider n troke* L * The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. 7 min max n troke* 055-L 10 500 n = min + n 10 108 770 Tab. 11 * Maximum stroke for a single-piece guiding rail and a maximum slider plate length max or longer strokes, see tab. 15 55D with double slider L lider lider troke* * The length of the safety stroke is provided on request according to the customer's specifi c requirements. Ln ig. 8 L min L max ** Ln troke* 55D 00 00 070 Ln = L min + n 5 108 770 Tab. 1 * Maximum stroke for a single-piece guiding rail and a minimum slider plate distance L min ** Maximum distance L max between the centres of slider plates at a stroke of 0 mm or longer strokes, see tab. 15 U-6

Uniline ystem Load ratings, moments and characteristic data 55 Driving belt The driving belt is manufactured from a friction resistant polyurethane and 0ax M x with steel cords for high tensile stress resistance. of belt elt width Weight kg/m M z 55 18RPP5 18 0.074 Tab. 1 elt length (mm) = x L - 18 tandard slider M y 0rad elt length (mm) = x L - n +18 Long slider elt length (mm) = x L - L n - 18 Double slider ig. 9 [] 0rad [] 0ax [] M x [m] M y [m] M z [m] 55 460 175 750 11.5 1.7 54.4 55-L 850 450 1500 8 to 5 9 to 65 55-D 850 450 1500 5 to 0 65 to 6677 or the calculation of the allowed moments, please observe pages L-5ff Tab. 14 Technical data tandard belt tension [] 0 Moment at no load [m] 0. 55 Max. traversing speed [m/s] 5 Max. acceleration [m/s²] 15 U Repeat accuracy 0.1 Linear accuracy 0.8 ompact Rail guiding rail lider type TLV8 8 spec. Moment of inertia Iy [cm 4 ] 4.6 Moment of inertia Iz [cm 4 ] 41.7 Pitch diameter of pulley [m] 0.0418 Moment of inertia of each pulley [gmm²] 456 troke per shaft revolution 10 Mass of slider [g] 475 Weight with zero stroke [g] 897 Weight with 1 m stroke [g] 4505 Max. stroke 5500 Working temperature from -0 to + 80 Tab. 15 U-7

1 Uniline series 75 75 system lider troke** L E G I, J Y K X ection - V W V H D ore diameter * M 8, 16,5 9 M * or information on the motor connection bores, see ordering key. ** The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. 10 * D E G* H I J K M X Y V W troke** 75 75 90 71.5 5 5.5 8.8 4.5 0 Ø 9.5 5 65 4.85 Ø 55 85 6 14.5. 70.4 116 40 Tab. 16 * or the position of the T-nuts when using our motor adapter plates, see pg. U-15ff ** Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 1 75L with long slider n troke* L * The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. 11 min max n troke* 75-L 440 700 n = min + n 10 116 000 Tab. 17 * Maximum stroke for a single-piece guiding rail and a maximum slider plate length max or longer strokes, see tab. 1 75D with double slider L lider lider troke* * The length of the safety stroke is provided on request according to the customer's specifi c requirements. Ln ig. 1 L min L max ** Ln troke* 75D 85 416 416 Ln = L min + n 8 116 000 Tab. 18 * Maximum stroke for a single-piece guiding rail and a minimum slider plate distance L min ** Maximum distance L max between the centres of slider plates at a stroke of 0 mm or longer strokes, see tab. 1 U-8

Uniline ystem Load ratings, moments and characteristic data 75 Driving belt The driving belt is manufactured from a friction resistant polyurethane and 0ax M x with steel cords for high tensile stress resistance. of belt elt width Weight kg/m M z 75 0RPP8 0 0.185 Tab. 19 elt length (mm) = x L - 1 tandard slider M y 0rad elt length (mm) = x L - n +7 Long slider elt length (mm) = x L - L n - 1 Double slider ig. 1 [] 0rad [] 0ax [] M x [m] M y [m] M z [m] 75 180 5500 1855 4.6 81.5 09 75-L 4560 11000 710 87. 87 to 770 85 to 8 75-D 4560 11000 710 87. 771 to 66 88 to 18788 or the calculation of the allowed moments, please observe pages L-5ff Tab. 0 Technical data 75 tandard belt tension [] 800 Moment at no load [m] 1.15 Max. traversing speed [m/s] 7 Max. acceleration [m/s²] 15 Repeat accuracy 0.1 Linear accuracy 0.8 ompact Rail guiding rail TLV4 lider type 4 spec. Moment of inertia Iy [cm 4 ] 17 Moment of inertia Iz [cm 4 ] 17 Pitch diameter of pulley [m] 0.0509 Moment of inertia of each pulley [gmm²] 19969 troke per shaft revolution 160 Mass of slider [g] 14 Weight with zero stroke [g] 679 Weight with 1 m stroke [g] 9751 Max. stroke 7500 Working temperature from -0 to + 80 Tab. 1 U U-9

1 Uniline series 100 100 system 5 0 180 0 4 M6 threads (on both sides) 5 5 10 5 8 M8 threads 17 45 10 1 lider troke* L J K 6 10, 1 0,1 H D 1 * The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. 14 1 D H J K 1 troke* 100 101 105 1.5 45.5 10.5 79 00 1 117 40 * Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 7 Tab. U-10

Uniline ystem 100L with long slider 10 5 0 84 0 4 M6 threads (on both sides) 5 5 4 5 8 M8 threads 17 45 1 n troke* L * The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. 15 min max n 1 troke* 100L 404 404 n = min = max 1 117 16 Tab. * Maximum stroke for a single-piece guiding rail and a maximum slider plate length max or longer strokes, see tab. 7 100D with double slider L 1 lider lider troke* 5 5 10 5 5 5 10 5 Ln U * The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. 16 L min L max ** Ln 1 troke* 100D 00 96 96 Ln = L min + n 50 1 117 04 Tab. 4 * Maximum stroke for a single-piece guiding rail and a minimum slider plate distance L min ** Maximum distance L max between the centres of slider plates at a stroke of 0 mm or longer strokes, see tab. 7 U-11

1 Uniline series Load ratings, moments and characteristic data 100 Driving belt The driving belt is manufactured from a friction resistant polyurethane and 0ax M x with steel cords for high tensile stress resistance. of belt elt width Weight kg/m M z 100 6T10 6 0.0 Tab. 5 elt length (mm) = x L - 197 tandard slider M y 0rad elt length (mm) = x L + 01 Long slider elt length (mm) = x L - L n - 197 Double slider ig. 17 [] 0rad [] 0ax [] M x [m] M y [m] M z [m] 100 0750 1500 700 50 50 600 100-L 0750 1500 700 50 500 100 100-D 61500 5000 14400 500 851 to 4451 4950 to 4450 or the calculation of the allowed moments, please observe pages L-5ff Tab. 6 Technical data 100 tandard belt tension [] 1000 Moment at no load [m]. Max. traversing speed [m/s] 9 Max. acceleration [m/s²] 0 Repeat accuracy 0.1 Linear accuracy 0.8 ompact Rail guiding rail lider type TLV6 6 spec. Moment of inertia Iy [cm 4 ] 500 Moment of inertia Iz [cm 4 ] 400 Pitch diameter of pulley [m] 0.06048 Moment of inertia of each pulley [gmm²] 0000 troke per shaft revolution 190 Mass of slider [g] 400 Weight with zero stroke [g] 1700 Weight with 1 m stroke [g] 15950 Max. stroke 5600 Working temperature from -0 to + 80 Tab. 7 U-1

Uniline ystem 100 motor connection model Motor connection via key 4 M6 threads (on both sides) G G I ore diameter * 1 M * or information on the motor connection bores, see ordering key ** or information on the motor drive shaft, see chapter ccessories, pg. U-15 ig. 18 100 motor connection model Motor connection via hrink Disk 4 M6 threads (on both sides) G G I ore diameter * 1 M U * ee chapter ccessories, pg. U-15 ig. 19 1 G I M 100 101 105.5.5 Ø 9,5 4 Ø 68 Tab. 8 U-1

1 Uniline series Lubrication The raceways of the guide rails in the Uniline linear axes are prelubricated. To achieve the calculated service life, a lubrication film must always be present between the raceway and the roller. The lubrication film also provides anticorrosion protection to the ground raceways. n approximate value for the lubrication period is every 100 km or every six months. The recommended lubricant is a lithium-based roller bearing grease of medium consistency. Lubrication of the raceways Proper lubrication under normal conditions: reduces friction reduces wear reduces stress on the contact faces reduces running noise Lubricants Thickeners Temperature range [ ] Dynamic viscosity [mpas] Roller bearing grease Lithium soap -0 to +170 <4500 Tab. 9 Relubrication of the guide rails These types of rails have a lubricating conduit on the side of the slider plate (type 100 is equipped with lubricating nipple) through which the lubricant can be applied directly to the raceways. Lubrication can be done in one of two ways: 1. Relubrication using a grease gun: This is done by inserting the tip of the grease gun into the conduit at the slider plate and injecting the grease inside (see fig. 0). Please note that the grease has to fill the whole conduit in order to lubricate the rail properly; for this reason sufficient grease must be used.. utomatic lubrication system: To connect the unit to an automatic greasing system, use a proper adapter/connector* that attaches to the threaded hole on the side of the trolley. The advantage of this solution is the possibility of rail re-lubrication without machine downtime. *(ny adapter that may be necessary must be manufactured on site) ig. 0 leaning the guide rails It is always recommended to clean the slider rail prior to any relubrication, in order to remove grease residues. This can be done while performing maintenance work or during a scheduled machine stop. 1. Unscrew the safety screws (on top of the slider plate) from the belt tensioning device (see fig. 1).. lso completely unscrew the belt tensioning screws and remove the belt tensioning devices from their housings.. Lift the toothed belt until the guide rails can be seen. Important: Ensure that the side seal is not damaged. 4. lean the rail raceways with a clean and dry cloth. Ensure that all grease and dirt residues from previous work processes are removed. To ensure that the rails are cleaned over their entire length, the slider plate should be moved once over its entire length. 5. pply a sufficient amount of grease to the raceways. 6. Re-insert the belt tensioning devices into their housings and mount the belt tensioning screws. Re-adjust the belt tension (see pg. U- 6). 7. asten the safety screws. ig. 1 U-14

Uniline ystem ccessories dapter plates tandard motor adapter plates Mounting plates for the most common motors or gearboxes. The connection bores for the motors or gearboxes must be made on site. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 10 E ection - Motor I x* side UILIE side * y * rea of plate needs to be cut if used for ED75 linear unit. (dding 0 mm to total length of unit will render this modification unnecessary). Othewise it gets in contact with the outer rail. X = 0 mm; Y = 5 mm H D G ig. ize D E G H I 40 110 40 8 1 4.5 0 17.5 14 Ø 0 Ø 55 16 55 100 5 50.5 7.5 18 15 Ø 0 Ø 47 75 15 70 106 5 5.5 5 19 17.5 Ø 5 Ø 55 Tab. 0 EM plates 1-P Mounting plates for EM motors or gearboxes. These plates are delivered ready-to-mount on the linear axes. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 10 ection - O I P Motor side UILIE side ize EM Motors / Gearboxes 40 EM E Q 45 x* * y U 55 EM 4 75 EM 4 Tab. 1 * rea of plate needs to be cut if used for ED75 linear unit. (dding 0 mm to total length of unit will render this modification unnecessary). Othewise it gets in contact with the outer rail. X = 0 mm; Y = 60 mm H D G 90 ig. ize D E G H I O P Q 40 110 70 8 1 4.5 5 17.5 9 0 Ø Ø 9 Ø 5 Ø 66.7 55 16 100 100 5 50.5 50 18 7.5 0 Ø 47 Ø 74 Ø 5.5 Ø 98.4 75 15 10 106 5 5.5 60 19 4.5 5 Ø 55 Ø 57 Ø 7.1 Ø 15.7 Tab. ynchronous use of linear axes in pairs If two axes are to be used in parallel using a connecting shaft, please specify when ordering, to ensure that the key slots of the pulleys are synchronized. U-15

1 Uniline series ixing brackets P- ixing clamp (for all sizes except 100) for simple mounting of a linear axis on a mounting surface or for connecting two units with or without a 5 5 ection - holes 4,5 6,5 connection plate (see pg. U-68). spacer* may be necessary. 4 *(ny spacer that may be necessary must be manufactured on site) 8,5 0 7, 0 15 0 7,5 40 ig. 4 T-nut izes 40-75 The maximum tightening torque is 10 m. ection - ig. 5 100 double or type 100 with motor connection only. 168 Ø19* Ø19* 6 7,9 1,5 M6 16,5 6 x 6 x key slot to DI 6885 6 x 6 x 5 key slot to DI 6885 1, 1, * lso available with a 0 mm diameter shaft ig. 6 100 conical fitting device -10M01 or type 100 with motor connection only. Rollon itting device Ø4 Ø19 6, 4,9 8 10 M6 Motor Intermediate plate* * ny intermediate plate that may be necessary must be manufactured on site. ig. 7 The maximum transferrable torque is 6 m. U-16

Uniline ystem ssembly kits T-connection plate P-1 T-connection plate allows two units to be mounted perpendicular to each other (see pg. U-65). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 165 55 55 6 6 5 5 4 1 6 6 1 1 5 4 5 1 150 luminum profile mounting side lider mounting side ngle connection plate P- ig. 8 ize ixing holes for the slider ixing holes for the profile 40 Holes 1 Holes 4 55 Holes Holes 5 75 Holes Holes 6 Tab. allows the right angle mounting of two units. The trolley of one unit can be mounted to the side of the other (see pg. U-66). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting to the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 7 8 75 8 1 6 5 lider mounting side luminum profile mounting side 4 1 1 165 6 5 1 ig. 9 ize ixing holes for the slider ixing holes for the profile 40 Holes 1 Holes 4 55 Holes Holes 5 75 Holes Holes 6 Tab. 4 U X connection plate P- X connection plate for mounting two sliders perpendicular to each other (see pg. U-67). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ize ixing holes for slider 1 ixing holes for slider 40 Holes 1 Holes 4 55 Holes Holes 5 75 Holes Holes 6 Tab. 5 160 5,5 55 ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 6 6 5 5 4 4 1 1 1 1 4 4 5 5,5 55 160 5 6 6 10 ig. 0 U-17

Ordering key Ordering key Identification code for Uniline linear unit U 07 04=40 05=55 07=75 10=100 1 1190 1 D 500 L 50 Indices of long slider plate see pg. U-4 - U-6 - U-8 - U-10 Indices of double slider plate, distance of the centers of slider plates see pg. U-4 - U-6 - U-8 - U-10 Profi le/rail code Driving head code L= Total length of the unit ize see pg. U-4 - U-6 - U-8 - U-10 Uniline prefi x Ordering example: U 07 1 1190 1 D 500 L 50 In order to create identifi cation codes for ctuator Line, you can visit: http://configureactuator.rollon.com U-18

Uniline ystem ccessories tandard motor adapter plate 07 tandard motor adapter plates ize see pg. U-15 (except 100) see pg. U-15 Ordering example: 07- Ordering information: The sizes are always specified with three digits with prefixed zeros. EM motor adapter plates 07 1 EM motor adapter plates ize see pg. U-15 (except 100) see pg. U-15 Ordering example: 07-1 Ordering information: The sizes are always specified with three digits with prefixed zeros. T-connection plate ngle connection plate X connection plate ixing clamp Order code: P-1 (for all sizes except 100), s. pg. U-17 Order code: P- (for all sizes except 100), s. pg. U-17 Order code: P- (for all sizes except 100), s. pg. U-17 Order code: P- (for all sizes except 100), s. pg. U-16 Motor connection bores U ize Hole [Ø] 40 55 75 100 Head code Metric with slot for key 10G8 / js9 1G8 / 4js9 14G8 / 5js9 19G8 / 6js9 1 10G8 / js9 16G8 / 5js9 0G8 / 6js9 14G8 / 5js9 19G8 / 6js9 16G8 / 5js9 Metric 18 1 for compression coupling 4 8 / 1 8 1 / 1 8 5 8 / 16 1P Inch [in] with slot for key 8 / 1 8 P 5 8 / 16 P The highlighted connection bores are standard connections Tab. 6 Metric: key seat for keys to DI 6885 form Inch: key seat for keys to 46 Part 1: 1958 4 U-19

Uniline series Uniline series Uniline series description ig. 1 Uniline is a family of ready-to-install linear actuators. They consist of internal ompact Rail roller sliders and steel-reinforced polyurethane belts in a rigid aluminum profile. Longitudinal seals enclose the system. This arrangement provides the best protection for the actuator from soiling and damage. In the series, the fixed bearing rail (T-rail) and the compensating bearing rail (U-rail) are mounted in the aluminum profile vertically. Versions with long (L) or double (D) sliders in one axis are possible. The most important characteristics: ompact design Protected internal linear guides High traversing speeds Grease-free operation possible (depending on the application. or further information, please contact our pplication Engineering department) High versatility Long strokes Versions with long or multiple sliders available in one linear axis Preferred areas of application: Handling and automation Multi-axis gantries Packaging machines utting machines Displaceable panels Painting installations Welding robots pecial machines Technical data: vailable sizes : : 55, 75 Length and stroke tolerances: or strokes <1 m: +0 mm to +10 mm (+0 in to 0.4 in) or strokes >1 m: +0 mm to +15 mm (+0 in to 0.59 in) U-0

Uniline ystem The components Extruded profile The anodized 6060 aluminum alloy extrusion used for the profi le of the Rollon Uniline series linear units were designed and manufactured by industry experts to optimize weight while maintaining mechanical strength. (see physical-chemical characteristics below).the dimensional tolerances comply with E 755-9 standard. be achieved. Optimization of the maximum belt width/body dimension ratio enables the following performance characteristics to be achieved: High speed Low noise Low wear Driving belt The Rollon Uniline series linear units use steel reinforced polyurethane drive belts with RPP pitch and parabolic profi les. This belt is ideal due to its high load transmission characteristics, compact size and low noise. Used in conjunction with a backlash-free pulley, smooth alternating motion can arriage The carriage of the Rollon Uniline series linear units are made entirely of anodized aluminum. Each carriage has mounting T-slots for the connection to the moving element. Rollon offers multiple carriages to accommodate a vast array of applications. General data about aluminum used: L 6060 hemical composition [%] I Mg i e Mn n u Impurites Remainder 0.5-0.60 0.0-0.60 0.0 0.10 0.10 0.10 0.05-0.15 Tab. 7 Physical characteristics Density kg dm oeff. of elasticity k mm oeff. of thermal expansion (0-100 ) 10-6 K Thermal conductivity (0 ) W m. K pecific heat (0-100 ) J kg. K Resistivity Melting point Ω. m. 10-9.7 69 00 880-900 600-655 Tab. 8 U Mechanical characteristics Rm Rp (0) H % mm mm 05 165 10 60-80 Tab. 9 U-1

Uniline series 55 55 system, J Y K X lider L ore diameter * troke** ection - V W V 8, 16,5 9 I H * or information on the motor connection bores, see ordering key. ** The length of the safety stroke is provided on request according to the customer's specifi c requirements. G E M M ig. * E G* H I J K M X Y V W troke** 55 55 71 67.5 50.5 7.5.5 15 Ø 4.9 1.5 5.5 Ø 47 00 8 1 0.5 54 108 1850 Tab. 40 * or the position of the T-nuts when using our motor adapter plates, see pg. U-7ff ** Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 45 55L with long slider * The length of the safety stroke is provided on request according to the customer's specifi c requirements. lider n troke* L ig. min max n troke* 55L 10 500 n = min + n 10 108 1550 Tab. 41 * Maximum stroke for a single-piece guiding rail and a maximum slider plate length max or longer strokes, see tab. 45 55D with double slider L lider lider troke* * The length of the safety stroke is provided on request according to the customer's specifi c requirements. Ln ig. 4 L min L max ** Ln troke* 55D 00 00 1850 Ln = L min + n 5 108 1570 Tab. 4 * Maximum stroke for a single-piece guiding rail and a minimum slider plate distance L min ** Maximum distance L max between the centres of slider plates at a stroke of 0 mm or longer strokes, see tab. 45 U-

Uniline ystem Load ratings, moments and characteristic data 55 Driving belt 0ax M x The driving belt is manufactured from a friction resistant polyurethane and with steel cords for high tensile stress resistance. of belt elt width Weight kg/m M z 55 18RPP5 18 0.074 Tab. 4 elt length (mm) = x L - 18 tandard slider M y 0rad elt length (mm) = x L - n +18 Long slider elt length (mm) = x L - L n - 18 Double slider ig. 5 [] 0rad [] 0ax [] M x [m] M y [m] M z [m] 55 560 00 1640 18.5 65.6 11.7 55-L 110 600 80 7 1 to 55 9 to 96 55-D 110 600 80 7 49 to 04 90 to 555 or the calculation of the allowed moments, please observe pages L-5ff Tab. 44 Technical data tandard belt tension [] 0 Moment at no load [m] 0. 55 Max. traversing speed [m/s] Max. acceleration [m/s²] 10 U Repeat accuracy 0.1 Linear accuracy 0.8 ompact Rail guiding rail lider type TLV18 / ULV18 18 spec. Moment of inertia Iy [cm 4 ] 4.4 Moment of inertia Iz [cm 4 ] 45.5 Pitch diameter of pulley [m] 0.0418 Moment of inertia of each pulley [gmm²] 456 troke per shaft revolution 10 Mass of slider [g] 549 Weight with zero stroke [g] 971 Weight with 1 m stroke [g] 4605 Max. stroke 5500 Working temperature from -0 to + 80 Tab. 45 U-

Uniline series 75 75 system lider L troke**, J Y K X ore diameter * ection - V W V 8, 16,5 9 I H * or information on the motor connection bores, see ordering key. ** The length of the safety stroke is provided on request according to the customer's specifi c requirements. G E M M ig. 6 * E G* H I J K M X Y V W troke** 75 75 90 71.5 5.5 8.8 4.5 0 Ø 9.5 5 65 4.85 Ø 55 85 6 14.5. 70.4 116 000 Tab. 46 * or the position of the T-nuts when using our motor adapter plates, see pg. U-7ff ** Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 51 75L with long slider * The length of the safety stroke is provided on request according to the customer's specifi c requirements. lider n troke* L ig. 7 min max n troke* 75L 440 700 n = min + n 10 116 610 Tab. 47 * Maximum stroke for a single-piece guiding rail and a maximum slider plate length max or longer strokes, see tab. 51 75D with double slider L lider lider troke* * The length of the safety stroke is provided on request according to the customer's specifi c requirements. Ln ig. 8 L min L max ** Ln troke* 75D 85 416 04 Ln = L min + n 8 116 610 Tab. 48 * Maximum stroke for a single-piece guiding rail and a minimum slider plate distance L min ** Maximum distance L max between the centres of slider plates at a stroke of 0 mm or longer strokes, see tab. 51 U-4

Uniline ystem Load ratings, moments and characteristic data 75 Driving belt 0ax M x The driving belt is manufactured from a friction resistant polyurethane and with steel cords for high tensile stress resistance. of belt elt width Weight kg/m M z 75 0RPP8 0 0.185 Tab. 49 elt length (mm) = x L - 1 tandard slider M y 0rad elt length (mm) = x L - n +7 Long slider elt length (mm) = x L - L n - 1 Double slider ig. 9 [] 0rad [] 0ax [] M x [m] M y [m] M z [m] 75 1470 750 450 85. 17 6.1 75-L 940 1500 8700 170.4 674 to 1805 116 to 11 75-D 940 1500 8700 170.4 1809 to 1154 1 to 68 or the calculation of the allowed moments, please observe pages L-5ff Tab. 50 Technical data tandard belt tension [] 800 Moment at no load [m] 1. 75 Max. traversing speed [m/s] 5 Max. acceleration [m/s²] 15 U Repeat accuracy 0.1 Linear accuracy 0.8 ompact Rail guiding rail lider type TLV8 / ULV8 8 spec. Moment of inertia Iy [cm 4 ] 108 Moment of inertia Iz [cm 4 ] 155 Pitch diameter of pulley [m] 0.0509 Moment of inertia of each pulley [gmm²] 19969 troke per shaft revolution 160 Mass of slider [g] 1666 Weight with zero stroke [g] 685 Weight with 1 m stroke [g] 9151 Max. stroke 7500 Working temperature from -0 to + 80 Tab. 51 U-5

Uniline series Lubrication The raceways of the guide rails in the Uniline linear axes are prelubricated. To achieve the calculated service life, a lubrication film must always be present between the raceway and the roller. The lubrication film also provides anticorrosion protection to the ground raceways. n approximate value for the lubrication period is every 100 km or every six months. The recommended lubricant is a lithium-based roller bearing grease of medium consistency. Lubrication of the raceways Proper lubrication under normal conditions: reduces friction reduces wear reduces stress on the contact faces reduces running noise Lubricants Thickeners Temperature range [ ] Dynamic viscosity [mpas] Roller bearing grease Lithium soap -0 to +170 <4500 Tab. 5 Relubrication of the guide rails 1. lide the slider plate to one end of the unit.. t about half the stroke press and manually move the belt in order to see one of the two rails inside the unit (see ig. 40). It may be necessary to release or loosen the belt tension. ee chapter elt tension (pg. U-6).. y using a grease syringe (not supplied by ROLLO) or an alternative tool (i.e. brush), apply a sufficient quantity of grease on the raceways. 4. If required, re-establish the recommended belt tension (see pg. U- 6). 5. inally slide the slider plate back and forth over the entire stroke, in order to distribute the grease over the entire length of the rail. leaning the guide rails It is always recommended to clean the slider rail prior to any relubrication, in order to remove grease residues. This can be done while performing maintenance work or during a scheduled machine stop. 1. Unscrew the safety screws (on top of the slider plate) from the belt tensioning device (see fig. 41).. lso completely unscrew the belt tensioning screws and remove the belt tensioning devices from their housings.. Lift the toothed belt until the guide rails can be seen. Important: Ensure that the side seal is not damaged. 4. lean the rail raceways with a clean and dry cloth. Ensure that all grease and dirt residues from previous work processes are removed. To ensure that the rails are cleaned over their entire length, the slider plate should be moved once over its entire length. 5. pply a sufficient amount of grease to the raceways. ig. 40 6. Re-insert the belt tensioning devices into their housings and mount the belt tensioning screws. Re-adjust the belt tension (see pg. U-6). 7. asten the safety screws. ig. 41 U-6

Uniline ystem ccessories dapter plates tandard motor adapter plates Mounting plates for the most common motors or gearboxes. The connection bores for the motors or gearboxes must be made on site. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 10 E ection - Motor I x* side UILIE side * y * rea of plate needs to be cut if used for ED75 linear unit. (dding 0 mm to total length of unit will render this modification unnecessary). Othewise it gets in contact with the outer rail. X = 0 mm; Y = 5 mm H D G ig. 4 ize D E G H I 55 16 55 100 5 50.5 7.5 18 15 Ø 0 Ø 47 75 15 70 106 5 5.5 5 19 17.5 Ø 5 Ø 55 Tab. 5 EM plates 1-P Mounting plates for EM motors or gearboxes. These plates are delivered ready-to-mount on the linear axes. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 10 ection - O I P Motor side UILIE side ize EM Motors / Gearboxes 55 EM 4 E Q 45 x* * y U 75 EM 4 Tab. 54 H D 90 * rea of plate needs to be cut if used for ED75 linear unit. (dding 0 mm to total length of unit will render this modification unnecessary). Othewise it gets in contact with the outer rail. X = 0 mm; Y = 60 mm G ig. 4 ize D E G H I O P Q 55 16 100 100 5 50.5 50 18 7.5 0 Ø 47 Ø 74 Ø 5.5 Ø 98.4 75 15 10 106 5 5.5 60 19 4.5 5 Ø 55 Ø 57 Ø 7.1 Ø 15.7 Tab. 55 ynchronous use of linear axes in pairs If two axes are to be used in parallel using a connecting shaft, please specify when ordering, to ensure that the key slots of the pulleys are synchronized. U-7

Uniline series ixing brackets P- 5 5 4 ection - holes 4,5 6,5 ixing clamp for simple mounting of a linear axis on a mounting surface or for connecting two units with or without a connection plate (see pg. U-68). spacer* may be necessary. *(ny spacer that may be necessary must be manufactured on site) 8,5 0 7, 0 40 15 0 7,5 ig. 44 T-nut izes 40-75 ection - The maximum tightening torque is 10 m. 6 7,9 1,5 M6 16,5 ig. 45 ssembly kits T-connection plate P-1 T-connection plate allows two units to be mounted perpendicular to each other (see pg. U-65). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 165 55 55 6 6 5 5 4 150 ize ixing holes for the slider ixing holes for the profile 55 Holes Holes 5 75 Holes Holes 6 Tab. 56 1 6 6 1 1 5 4 5 1 luminum profile mounting side lider mounting side ig. 46 U-8

Uniline ystem ngle connection plate P- allows the right angle mounting of two units. The trolley of one unit can be mounted to the side of the other (see pg. U-66). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting to the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 7 8 8 6 5 lider mounting side luminum profile mounting side 4 6 5 ize ixing holes for the slider ixing holes for the profile 55 Holes Holes 5 75 Holes Holes 6 Tab. 57 75 1 1 1 1 165 ig. 47 X connection plate P- X connection plate for mounting two sliders perpendicular to each other (see pg. U-67). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ize ixing holes for slider 1 ixing holes for slider 55 Holes Holes 5 75 Holes Holes 6 Tab. 58 160 5,5 55 ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 6 6 5 5 4 4 1 1 1 1 4 4 5 5,5 55 160 5 6 6 10 ig. 48 U U-9

Ordering key Ordering key Identification code for Uniline linear unit U 07 05=55 07=75 1 1190 1 D 500 L 50 Indices of long slider plate see from pg. U- to pg. U-4 Driving head code Indices of double slider plate, distance of the centers of slider plates see from pg. U- to pg. U-4 Profi le/rail code L= Total length of the unit ize see from pg. U- to pg. U-4 Uniline prefi x Ordering example: U 07 1 1190 1 D 500 L 50 In order to create identifi cation codes for ctuator Line, you can visit: http://configureactuator.rollon.com U-0

Uniline ystem ccessories tandard motor adapter plate 07 tandard motor adapter plates ize see pg. U-7 see pg. U-7 Ordering example: 07- Ordering information: The sizes are always specified with three digits with prefixed zeros. EM motor adapter plates 07 1 EM motor adapter plates ize see pg. U-7 see pg. U-7 Ordering example: 07-1 Ordering information: The sizes are always specified with three digits with prefixed zeros. T-connection plate ngle connection plate X connection plate ixing clamp Order code: P-1, s. pg. U-8 Order code: P-, s. pg. U-9 Order code: P-, s. pg. U-9 Order code: P-, s. pg. U-8 Motor connection bores U ize Hole [Ø] 55 75 Head code Metric with slot for key 1G8 / 4js9 14G8 / 5js9 1 10G8 / js9 16G8 / 5js9 14G8 / 5js9 19G8 / 6js9 16G8 / 5js9 Metric 18 1 for compression coupling 4 1 / 1 8 5 8 / 16 1P Inch [in] with slot for key 8 / 1 8 P 5 8 / 16 P The highlighted connection bores are standard connections Tab. 59 Metric: key seat for keys to DI 6885 form Inch: key seat for keys to 46 Part 1: 1958 4 U-1

Uniline E series Uniline E series Uniline E series description ig. 49 Uniline is a family of ready-to-install linear actuators. They consist of internal ompact Rail roller sliders and steel-reinforced polyurethane belts in a rigid aluminum profile. Longitudinal seals enclose the system. This arrangement provides the best protection for the actuator from soiling and damage. In the E series, the fixed bearing rail (T-rail) is mounted horizontally in the aluminum profile, and the compensating bearing rail (U-rail) is flanged to the outside of the profile as moment support. Versions with long (L) or double (D) sliders in one axis are possible. The most important characteristics: ompact design Protected internal linear guides High traversing speeds Grease-free operation possible (depending on the application. or further information, please contact our pplication Engineering department) High versatility Long strokes Versions with long or multiple sliders available in one linear axis Preferred areas of application: Handling and automation Multi-axis gantries Packaging machines utting machines Displaceable panels Painting installations Welding robots pecial machines Technical data: vailable sizes : E: 55, 75 Length and stroke tolerances: or strokes <1 m: +0 mm to +10 mm (+0 in to 0.4 in) or strokes >1 m: +0 mm to +15 mm (+0 in to 0.59 in) U-

Uniline ystem The components Extruded profile The anodized 6060 aluminum alloy extrusion used for the profi le of the Rollon Uniline E series linear units were designed and manufactured by industry experts to optimize weight while maintaining mechanical strength. (see physical-chemical characteristics below).the dimensional tolerances comply with E 755-9 standard. be achieved. Optimization of the maximum belt width/body dimension ratio enables the following performance characteristics to be achieved: High speed Low noise Low wear Driving belt The Rollon Uniline E series linear units use steel reinforced polyurethane drive belts with RPP pitch and parabolic profi les. This belt is ideal due to its high load transmission characteristics, compact size and low noise. Used in conjunction with a backlash-free pulley, smooth alternating motion can arriage The carriage of the Rollon Uniline E series linear units are made entirely of anodized aluminum. Each carriage has mounting T-slots for the connection to the moving element. Rollon offers multiple carriages to accommodate a vast array of applications. General data about aluminum used: L 6060 hemical composition [%] I Mg i e Mn n u Impurites Remainder 0.5-0.60 0.0-0.60 0.0 0.10 0.10 0.10 0.05-0.15 Tab. 60 Physical characteristics Density kg dm oeff. of elasticity k mm oeff. of thermal expansion (0-100 ) 10-6 K Thermal conductivity (0 ) W m. K pecific heat (0-100 ) J kg. K Resistivity Melting point Ω. m. 10-9.7 69 00 880-900 600-655 Tab. 61 U Mechanical characteristics Rm Rp (0) H % mm mm 05 165 10 60-80 Tab. 6 U-

Uniline E series E55 E55 system lider troke** L J Y X K ore diameter * ection - V W V, H D 16,5 9 8, * or information on the motor connection bores, see ordering key. ** The length of the safety stroke is provided on request according to the customer's specifi c requirements. G E I M M ig. 50 * D E G* H I J K M X Y V W troke** E55 55 71 67.5 5 50.5 7.5.5 15 Ø 4.9 1.5 71.5 Ø 47 00 8 1 0.5 54 108 070 Tab. 6 * or the position of the T-nuts when using our motor adapter plates, see pg. U-9ff ** Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 68 E55L with long slider * The length of the safety stroke is provided on request according to the customer's specifi c requirements. lider n troke* L ig. 51 min max n troke* E55L 10 500 n = min + n 10 108 770 Tab. 64 * Maximum stroke for a single-piece guiding rail and a maximum slider plate length max or longer strokes, see tab. 68 E55D with double slider L lider lider troke* * The length of the safety stroke is provided on request according to the customer's specifi c requirements. Ln ig. 5 L min L max ** Ln troke* E55D 00 00 070 Ln = L min + n 5 108 770 Tab. 65 * Maximum stroke for a single-piece guiding rail and a minimum slider plate distance L min ** Maximum distance L max between the centres of slider plates at a stroke of 0 mm or longer strokes, see tab. 68 U-4

Uniline ystem Load ratings, moments and characteristic data E55 Driving belt The driving belt is manufactured from a friction resistant polyurethane and 0ax M x with steel cords for high tensile stress resistance. of belt elt width Weight kg/m M z E55 18RPP5 18 0.074 Tab. 66 elt length (mm) = x L - 18 tandard slider M y 0rad elt length (mm) = x L - n +18 Long slider elt length (mm) = x L - L n - 18 Double slider ig. 5 [] 0rad [] 0ax [] M x [m] M y [m] M z [m] E55 460 175 1500 5.5 4.4 54.4 E55-L 850 450 000 51 165 to 450 9 to 65 E55-D 850 450 000 51 450 to 4605 65 to 6677 or the calculation of the allowed moments, please observe pages L-5ff Tab. 67 Technical data tandard belt tension [] 0 Moment at no load [m] 0. E55 Max. traversing speed [m/s] Max. acceleration [m/s²] 10 U Repeat accuracy 0.1 Linear accuracy 0.8 ompact Rail guiding rail TLV8 / ULV18 lider type 8 spec. / P 18 Moment of inertia Iy [cm 4 ] 4.6 Moment of inertia Iz [cm 4 ] 41.7 Pitch diameter of pulley [m] 0.0418 Moment of inertia of each pulley [gmm²] 456 troke per shaft revolution 10 Mass of slider [g] 65 Weight with zero stroke [g] 167 Weight with 1 m stroke [g] 5055 Max. stroke 5500 Working temperature from -0 to + 80 Tab. 68 U-5

Uniline E series E75 E75 system lider troke** L J Y X K ore diameter * ection - V W V, H D 16,5 9 8, * or information on the motor connection bores, see ordering key. ** The length of the safety stroke is provided on request according to the customer's specifi c requirements. G E I M M ig. 54 * D E G* H I J K M X Y V W troke** E75 75 90 71.5 5 5.5 8.8 4.5 0 Ø 9.5 5 95 4.85 Ø 55 85 6 14.5. 70.4 116 40 Tab. 69 * or the position of the T-nuts when using our motor adapter plates, see pg. U-9ff ** Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 74 E75L with long slider * The length of the safety stroke is provided on request according to the customer's specifi c requirements. lider n troke* L ig. 55 min max n troke* E75L 440 700 n = min + n 10 116 000 Tab. 70 * Maximum stroke for a single-piece guiding rail and a maximum slider plate length max or longer strokes, see tab. 74 E75D with double slider L lider lider troke* * The length of the safety stroke is provided on request according to the customer's specifi c requirements. Ln ig. 56 L min L max ** Ln troke* E75D 85 416 416 Ln = L min + n 8 116 000 Tab. 71 * Maximum stroke for a single-piece guiding rail and a minimum slider plate distance L min ** Maximum distance L max between the centres of slider plates at a stroke of 0 mm or longer strokes, see tab. 74 U-6

Uniline ystem Load ratings, moments and characteristic data E75 Driving belt The driving belt is manufactured from a friction resistant polyurethane and 0ax M x with steel cords for high tensile stress resistance. of belt elt width Weight kg/m M z E75 0RPP8 0 0.185 Tab. 7 elt length (mm) = x L - 1 tandard slider M y 0rad elt length (mm) = x L - n +7 Long slider elt length (mm) = x L - L n - 1 Double slider ig. 57 [] 0rad [] 0ax [] M x [m] M y [m] M z [m] E75 180 5500 710 85.5 16 09 E75-L 4560 11000 740 171 575 to 1540 85 to 8 E75-D 4560 11000 740 171 154 to 167 88 to 18788 or the calculation of the allowed moments, please see pages L-5ff Tab. 7 Technical data tandard belt tension [] 800 Moment at no load [m] 1. E75 Max. traversing speed [m/s] 5 Max. acceleration [m/s²] 15 U Repeat accuracy 0.1 Linear accuracy 0.8 ompact Rail guiding rail TLV4 / ULV8 lider type 4 spec. / P 8 Moment of inertia Iy [cm 4 ] 17 Moment of inertia Iz [cm 4 ] 17 Pitch diameter of pulley [m] 0.0509 Moment of inertia of each pulley [gmm²] 19969 troke per shaft revolution 160 Mass of slider [g] 177 Weight with zero stroke [g] 7544 Weight with 1 m stroke [g] 10751 Max. stroke 7500 Working temperature from -0 to + 80 Tab. 74 U-7

Uniline E series Lubrication The raceways of the guide rails in the Uniline linear axes are prelubricated. To achieve the calculated service life, a lubrication film must always be present between the raceway and the roller. The lubrication film also provides anticorrosion protection to the ground raceways. n approximate value for the lubrication period is every 100 km or every six months. The recommended lubricant is a lithium-based roller bearing grease of medium consistency. Lubrication of the raceways Proper lubrication under normal conditions: reduces friction reduces wear reduces stress on the contact faces reduces running noise Lubricants Thickeners Temperature range [ ] Dynamic viscosity [mpas] Roller bearing grease Lithium soap -0 to +170 <4500 Tab. 75 Relubrication of the guide rails These types of rails have a lubricating conduit on the side of the slider plate through which the lubricant can be applied directly to the raceways. Lubrication can be done in one of two ways: The advantage of this solution is the possibility of rail re-lubrication without machine downtime. *(ny adapter that may be necessary must be manufactured on site) 1. Relubrication using a grease gun: This is done by inserting the tip of the grease gun into the conduit at the slider plate and injecting the grease inside (see fig. 58). Please note that the grease has to fill the whole conduit in order to lubricate the rail properly; for this reason sufficient grease must be used.. utomatic lubrication system: To connect the unit to an automatic greasing system, use a proper adapter/connector* that attaches to the threaded hole on the side of the trolley. ig. 58 leaning the guide rails It is always recommended to clean the slider rail prior to any relubrication, in order to remove grease residues. This can be done while performing maintenance work or during a scheduled machine stop. 1. Unscrew the safety screws (on top of the slider plate) from the belt tensioning device (see fig. 59).. lso completely unscrew the belt tensioning screws and remove the belt tensioning devices from their housings.. Lift the toothed belt until the guide rails can be seen. Important: Ensure that the side seal is not damaged. 4. lean the rail raceways with a clean and dry cloth. Ensure that all grease and dirt residues from previous work processes are removed. To ensure that the rails are cleaned over their entire length, the slider plate should be moved once over its entire length. 5. pply a sufficient amount of grease to the raceways. 6. Re-insert the belt tensioning devices into their housings and mount the belt tensioning screws. Re-adjust the belt tension (see pg. U-6). 7. asten the safety screws. ig. 59 U-8

Uniline ystem ccessories dapter plates tandard motor adapter plates Mounting plates for the most common motors or gearboxes. The connection bores for the motors or gearboxes must be made on site. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 10 E ection - Motor I x* side UILIE side * y * rea of plate needs to be cut if used for ED75 linear unit. (dding 0 mm to total length of unit will render this modification unnecessary). Othewise it gets in contact with the outer rail. X = 0 mm; Y = 5 mm H D G ig. 60 ize D E G H I 55 16 55 100 5 50.5 7.5 18 15 Ø 0 Ø 47 75 15 70 106 5 5.5 5 19 17.5 Ø 5 Ø 55 Tab. 76 EM plates 1-P Mounting plates for EM motors or gearboxes. These plates are delivered ready-to-mount on the linear axes. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 10 ection - O I P Motor side UILIE side ize EM Motors / Gearboxes 55 EM 4 E Q 45 x* * y U 75 EM 4 Tab. 77 H D 90 * rea of plate needs to be cut if used for ED75 linear unit. (dding 0 mm to total length of unit will render this modification unnecessary). Othewise it gets in contact with the outer rail. X = 0 mm; Y = 60 mm G ig. 61 ize D E G H I O P Q 55 16 100 100 5 50.5 50 18 7.5 0 Ø 47 Ø 74 Ø 5.5 Ø 98.4 75 15 10 106 5 5.5 60 19 4.5 5 Ø 55 Ø 57 Ø 7.1 Ø 15.7 Tab. 78 ynchronous use of linear axes in pairs If two axes are to be used in parallel using a connecting shaft, please specify when ordering, to ensure that the key slots of the pulleys are synchronized. U-9

Uniline E series ixing brackets P- 5 5 4 ection - holes 4,5 6,5 ixing clamp for simple mounting of a linear axis on a mounting surface or for connecting two units with or without a connection plate (see pg. U-68). spacer* may be necessary. *(ny spacer that may be necessary must be manufactured on site) 8,5 0 7, 0 40 15 0 7,5 ig. 6 T-nut izes 40-75 ection - The maximum tightening torque is 10 m. 6 7,9 1,5 M6 16,5 ig. 6 ssembly kits T-connection plate P-1 T-connection plate allows two units to be mounted perpendicular to each other (see pg. U-65). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 165 55 55 6 6 5 5 4 150 ote This adapter plate can be used with types E and ED only to a limited extent. or further information, please contact our pplication Engineering Department. ize ixing holes for the slider ixing holes for the profile 55 Holes Holes 5 75 Holes Holes 6 Tab. 79 1 6 6 1 1 5 4 5 1 luminum profile mounting side lider mounting side ig. 64 U-40

Uniline ystem ngle connection plate P- allows the right angle mounting of two units. The trolley of one unit can be mounted to the side of the other (see pg. U-66). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting to the linear units. ote This adapter plate can be used with types E and ED only to a limited extent. or further information, please contact our pplication Engineering Department. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 7 8 8 6 5 lider mounting side luminum profile mounting side 4 6 5 ize ixing holes for the slider ixing holes for the profile 55 Holes Holes 5 75 Holes Holes 6 Tab. 80 75 1 1 1 1 165 ig. 65 X connection plate P- X connection plate for mounting two sliders perpendicular to each other (see pg. U-67). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ize ixing holes for slider 1 ixing holes for slider 55 Holes Holes 5 75 Holes Holes 6 Tab. 81 160 5,5 55 ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 6 6 5 5 4 4 1 1 1 1 4 4 5 5,5 55 160 5 6 6 10 U ig. 66 U-41

Ordering key Ordering key Identification code for Uniline linear unit U E 07 05=55 07=75 1 1190 1 D 500 L 50 Indices of long slider plate see from pg. U-4 to pg. U-6 Uniline prefi x ize Driving head code Ordering example: UE 07 1 1190 1 D 500 L 50 Indices of double slider plate, distance of the centers of slider plates see from pg. U-4 to pg. U-6 Profi le/rail code L= Total length of the unit see from pg. U-4 to pg. U-6 In order to create identifi cation codes for ctuator Line, you can visit: http://configureactuator.rollon.com U-4

Uniline ystem ccessories tandard motor adapter plate E 07 ize tandard motor adapter plates see pg. U-9 see pg. U-9 Ordering example: E07- Ordering information: The sizes are always specified with three digits with prefixed zeros. EM motor adapter plates E 07 1 ize EM motor adapter plates see pg. U-9 see pg. U-9 Ordering example: E07-1 Ordering information: The sizes are always specified with three digits with prefixed zeros. T-connection plate ngle connection plate X connection plate ixing clamp Order code: P-1, s. pg. U-40 Order code: P-, s. pg. U-41 Order code: P-, s. pg. U-41 Order code: P-, s. pg. U-40 Motor connection bores U ize Hole [Ø] 55 75 Head code Metric with slot for key 1G8 / 4js9 14G8 / 5js9 1 10G8 / js9 16G8 / 5js9 14G8 / 5js9 19G8 / 6js9 16G8 / 5js9 Metric 18 1 for compression coupling 4 1 / 1 8 5 8 / 16 1P Inch [in] with slot for key 8 / 1 8 P 5 8 / 16 P The highlighted connection bores are standard connections Tab. 8 Metric: key seat for keys to DI 6885 form Inch: key seat for keys to 46 Part 1: 1958 4 U-4

4 Uniline ED series Uniline ED series Uniline ED series description ig. 67 Uniline is a family of ready-to-install linear actuators. They consist of internal ompact Rail roller sliders and steel-reinforced polyurethane belts in a rigid aluminum profile. Longitudinal seals enclose the system. This arrangement provides the best protection for the actuator from soiling and damage. In the ED series, a compensating bearing rail (U-rail) is mounted horizontally in the aluminum profile, and for increased moment support, two more compensating bearing rails (U-rail) are flanged to the profile externally. Versions with long (L) or double (D) sliders in one axis are possible. Preferred areas of application: Handling and automation Multi-axis gantries Packaging machines utting machines Displaceable panels Painting installations Welding robots pecial machines The most important characteristics: ompact design Protected internal linear guides High traversing speeds Grease-free operation possible (depending on the application. or further information, please contact our pplication Engineering department) High versatility Long strokes Versions with long or multiple sliders available in one linear axis Technical data: vailable sizes : ED: 75 Length and stroke tolerances: or strokes <1 m: +0 mm to +10 mm (+0 in to 0.4 in) or strokes >1 m: +0 mm to +15 mm (+0 in to 0.59 in) U-44

Uniline ystem The components Extruded profile The anodized 6060 aluminum alloy extrusion used for the profi le of the Rollon Uniline ED series linear units were designed and manufactured by industry experts to optimize weight while maintaining mechanical strength. (see physical-chemical characteristics below).the dimensional tolerances comply with E 755-9 standard. be achieved. Optimization of the maximum belt width/body dimension ratio enables the following performance characteristics to be achieved: High speed Low noise Low wear Driving belt The Rollon Uniline ED series linear units use steel reinforced polyurethane drive belts with RPP pitch and parabolic profi les. This belt is ideal due to its high load transmission characteristics, compact size and low noise. Used in conjunction with a backlash-free pulley, smooth alternating motion can arriage The carriage of the Rollon Uniline ED series linear units are made entirely of anodized aluminum. Each carriage has mounting T-slots for the connection to the moving element. Rollon offers multiple carriages to accommodate a vast array of applications. General data about aluminum used: L 6060 hemical composition [%] I Mg i e Mn n u Impurites Remainder 0.5-0.60 0.0-0.60 0.0 0.10 0.10 0.10 0.05-0.15 Tab. 8 Physical characteristics Density kg dm oeff. of elasticity k mm oeff. of thermal expansion (0-100 ) 10-6 K Thermal conductivity (0 ) W m. K pecific heat (0-100 ) J kg. K Resistivity Melting point Ω. m. 10-9.7 69 00 880-900 600-655 Tab. 84 U Mechanical characteristics Rm Rp (0) H % mm mm 05 165 10 60-80 Tab. 85 U-45

4 Uniline ED series ED75 ED75 system lider troke** L 8,, 16,5 9 K X Y H D ore diameter * G M E * or information on the motor connection bores, see ordering key. ** The length of the safety stroke is provided on request according to the customer's specifi c requirements. I ection - V W V M ig. 68 * D E G* H I K M X Y V W troke** ED75 75 90 71.5 5 5.5 8.8 4.5 0 Ø 9.5 15 4.85 Ø 55 0 6 49.5. 70.4 116 900 Tab. 86 * or the position of the T-nuts when using our motor adapter plates, see pg. U-49ff ** Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 91 ED75L with long slider lider troke* L * The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. 69 min * max n troke** ED75L 440 700 n = min + n 10 116 500 Tab. 87 * The length of 440 mm is considered standard, all other lengths are considered special dimensions ** Maximum stroke for a single-piece guiding rail and a maximum slider plate length max or longer strokes, see tab. 91 ED75D with double slider L lider lider troke* * The length of the safety stroke is provided on request according to the customer's specifi c requirements. Ln ig. 70 L min L max ** Ln troke* ED75D 0 416 864 Ln = L min + n 8 116 450 Tab. 88 * Maximum stroke for a single-piece guiding rail and a minimum slider plate distance L min ** Maximum distance L max between the centres of slider plates at a stroke of 0 mm or longer strokes, see tab. 91 U-46

Uniline ystem ED Driving belt 0ax M x with steel cords for high tensile stress resistance. The driving belt is manufactured from a friction resistant polyurethane and of belt elt width Weight kg/m M z ED75 0RPP8 0 0.185 Tab. 89 elt length (mm) = x L - 58 tandard slider M y 0rad elt length (mm) = x L - n +7 Long slider elt length (mm) = x L - L n - 58 Double slider ig. 71 [] 0rad [] 0ax [] M x [m] M y [m] M z [m] ED75 9815 5500 8700 400. 868 09 ED75-L 1960 11000 8700 400. 1174 to 05 85 to 8 ED75-D 1960 11000 17400 800.4 619 to 4917 88 to 1575 or the calculation of the allowed moments, please see pages L-5ff Tab. 90 Technical data ED75 tandard belt tension [] 1000 Moment at no load [m] 1.5 Max. traversing speed [m/s] 5 Max. acceleration [m/s²] 15 U Repeat accuracy 0.1 Linear accuracy 0.8 ompact Rail guiding rail lider type ULV4 / ULV8 4 spec. / 8 spec. Moment of inertia Iy [cm 4 ] 17 Moment of inertia Iz [cm 4 ] 17 Pitch diameter of pulley [m] 0.0509 Moment of inertia of each pulley [gmm²] 19969 troke per shaft revolution 160 Mass of slider [g] 770 Weight with zero stroke [g] 9850 Weight with 1 m stroke [g] 14400 Max. stroke 7500 Working temperature from -0 to + 80 Tab. 91 U-47

4 Uniline ED series Lubrication The raceways of the guide rails in the Uniline linear axes are prelubricated. To achieve the calculated service life, a lubrication film must always be present between the raceway and the roller. The lubrication film also provides anticorrosion protection to the ground raceways. n approximate value for the lubrication period is every 100 km or every six months. The recommended lubricant is a lithium-based roller bearing grease of medium consistency. Lubrication of the raceways Proper lubrication under normal conditions: reduces friction reduces wear reduces stress on the contact faces reduces running noise Lubricants Thickeners Temperature range [ ] Dynamic viscosity [mpas] Roller bearing grease Lithium soap -0 to +170 <4500 Tab. 9 Relubrication of the guide rails 1. lide the slider plate to one end of the unit.. t about half the stroke press and manually move the belt in order to see one of the two rails inside the unit (see ig. 7). It may be necessary to release or loosen the belt tension. ee chapter elt tension (pg. U-6).. y using a grease syringe (not supplied by ROLLO) or an alternative tool (i.e. brush), apply a sufficient quantity of grease on the raceways. 4. If required, re-establish the recommended belt tension (see pg. U- 6). 5. inally slide the slider plate back and forth over the entire stroke, in order to distribute the grease over the entire length of the rail. leaning the guide rails It is always recommended to clean the slider rail prior to any relubrication, in order to remove grease residues. This can be done while performing maintenance work or during a scheduled machine stop. 1. Unscrew the safety screws (on top of the slider plate) from the belt tensioning device (see fig. 7).. lso completely unscrew the belt tensioning screws and remove the belt tensioning devices from their housings.. Lift the toothed belt until the guide rails can be seen. Important: Ensure that the side seal is not damaged. 4. lean the rail raceways with a clean and dry cloth. Ensure that all grease and dirt residues from previous work processes are removed. To ensure that the rails are cleaned over their entire length, the slider plate should be moved once over its entire length. 5. pply a sufficient amount of grease to the raceways. ig. 7 6. Re-insert the belt tensioning devices into their housings and mount the belt tensioning screws. Re-adjust the belt tension (see pg. U-6). 7. asten the safety screws. ig. 7 U-48

Uniline ystem ccessories dapter plates tandard motor adapter plates Mounting plates for the most common motors or gearboxes. The connection bores for the motors or gearboxes must be made on site. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 10 E ection - Motor I x* side UILIE side * y * rea of plate needs to be cut if used for ED75 linear unit. (dding 0 mm to total length of unit will render this modification unnecessary). Othewise it gets in contact with the outer rail. X = 0 mm; Y = 5 mm H D G ig. 74 ize D E G H I 75 15 70 106 5 5.5 5 19 17.5 Ø 5 Ø 55 Tab. 9 EM plates 1-P Mounting plates for EM motors or gearboxes. These plates are delivered ready-to-mount on the linear axes. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 10 ection - O I P Motor side UILIE side ize EM Motors / Gearboxes 75 EM 4 Tab. 94 H D E Q 45 90 x* * y U * rea of plate needs to be cut if used for ED75 linear unit. (dding 0 mm to total length of unit will render this modification unnecessary). Othewise it gets in contact with the outer rail. X = 0 mm; Y = 60 mm G ig. 75 ize D E G H I O P Q 75 15 10 106 5 5.5 60 19 4.5 5 Ø 55 Ø 57 Ø 7.1 Ø 15.7 Tab. 95 ynchronous use of linear axes in pairs If two axes are to be used in parallel using a connecting shaft, please specify when ordering, to ensure that the key slots of the pulleys are synchronized. U-49

4 Uniline ED series ixing brackets P- 5 5 4 ection - holes 4,5 6,5 ixing clamp for simple mounting of a linear axis on a mounting surface or for connecting two units with or without a connection plate (see pg. U-68). spacer* may be necessary. *(ny spacer that may be necessary must be manufactured on site) 8,5 0 7, 0 40 15 0 7,5 ig. 76 T-nut izes 40-75 ection - The maximum tightening torque is 10 m. 6 7,9 1,5 M6 16,5 ig. 77 ssembly kits T-connection plate P-1 T-connection plate allows two units to be mounted perpendicular to each other (see pg. U-65). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 165 55 55 6 6 5 5 4 150 ote This adapter plate can be used with types E and ED only to a limited extent. or further information, please contact our pplication Engineering Department. ize ixing holes for the slider ixing holes for the profile 75 Holes Holes 6 Tab. 96 1 6 6 1 1 5 4 5 1 luminum profile mounting side lider mounting side ig. 78 U-50

Uniline ystem ngle connection plate P- allows the right angle mounting of two units. The trolley of one unit can be mounted to the side of the other (see pg. U-66). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting to the linear units. ote This adapter plate can be used with types E and ED only to a limited extent. or further information, please contact our pplication Engineering Department. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 7 8 8 6 5 lider mounting side luminum profile mounting side 4 6 5 ize ixing holes for the slider ixing holes for the profile 75 Holes Holes 6 Tab. 97 75 1 1 1 1 165 ig. 79 X connection plate P- X connection plate for mounting two sliders perpendicular to each other (see pg. U-67). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ize ixing holes for slider 1 ixing holes for slider 75 Holes Holes 6 Tab. 98 160 5,5 55 ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 6 6 5 5 4 4 1 1 1 1 4 4 5 5,5 55 160 5 6 6 10 U ig. 80 U-51

Ordering key Ordering key Identification code for Uniline linear unit U D 07 07=75 1 1190 1 D 500 L 50 Driving head code Indices of long slider plate see pg. U-46 Indices of double slider plate, distance of the centers of slider plates see pg. U-46 Profi le/rail code L= Total length of the unit ize see pg. U-46 Uniline prefi x Ordering example: UD 07 1 1190 1 D 500 L 50 In order to create identifi cation codes for ctuator Line, you can visit: http://configureactuator.rollon.com U-5

Uniline ystem ccessories tandard motor adapter plate D 07 ize tandard motor adapter plates see pg. U-49 see pg. U-49 Ordering example: D07- Ordering information: The sizes are always specified with three digits with prefixed zeros. EM motor adapter plates D 07 1 ize EM motor adapter plates see pg. U-49 see pg. U-49 Ordering example: D07-1 Ordering information: The sizes are always specified with three digits with prefixed zeros. T-connection plate ngle connection plate X connection plate ixing clamp Order code: P-1, s. pg. U-50 Order code: P-, s. pg. U-51 Order code: P-, s. pg. U-51 Order code: P-, s. pg. U-50 Motor connection bores U ize Hole [Ø] 75 Head code Metric with slot for key 14G8 / 5js9 16G8 / 5js9 19G8 / 6js9 1 4 Metric 18 1 for compression coupling 4 Inch [in] with slot for key 5 8 / 16 1P P P Tab. 99 The highlighted connection bores are standard connections Metric: key seat for keys to DI 6885 form Inch: key seat for keys to 46 Part 1: 1958 U-5

5 Uniline H series Uniline H series Uniline H series description ig. 81 Uniline is a family of ready-to-install linear actuators. They consist of internal ompact Rail roller sliders in a rigid aluminum profile. Longitudinal seals enclose the system. This arrangement provides the best protection for the actuator from soiling and damage. In the H series, the compensating bearing rail (U-rail) is mounted horizontally in the aluminum profile. The H series is used as a compensating bearing axis for load absorption of radial forces, and in combination with the other series, as support bearing for the resulting moments. Versions with long (L) or double (D) sliders in one axis are possible. H series is a slave actuator, it has not the driving belt. The most important characteristics: ompact design Protected internal linear guides High traversing speeds Grease-free operation possible (depending on the application. or further information, please contact our pplication Engineering department) High versatility Long strokes Versions with long or multiple sliders available in one linear axis Preferred areas of application: Handling and automation Multi-axis gantries Packaging machines utting machines Displaceable panels Painting installations Welding robots pecial machines Technical data: vailable sizes : H: 40, 55, 75 Length and stroke tolerances: or strokes <1 m: +0 mm to +10 mm (+0 in to 0.4 in) or strokes >1 m: +0 mm to +15 mm (+0 in to 0.59 in) U-54

5 Uniline H series H40 H40 system 4,5 80 4 M4 threads 15 7,5 lider troke* L, J K 8, 16,5 9 H * The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. 8 * nom min max D H J K X Y troke** H40 40 51.5 51. 5.6-14 5 0 165 - - 1 1900 Tab. 10 * Including long or double slider. ee chapter Product dimensions s...l and...d ** Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 105 H40 0ax Technical data H40 M z Max. traversing speed [m/s] Max. acceleration [m/s²] 10 Repeat accuracy 0.1 Linear accuracy 0.8 M y 0rad ompact Rail guiding rail ULV18 M x lider type 18 spec. ig. 8 Moment of inertia Iy [cm 4 ] 1 Moment of inertia Iz [cm 4 ] 1.6 [] 0rad [] 0ax [] M x [m] M y [m] M z [m] Mass of slider [g] 0 Weight with zero stroke [g] 860 H40 150 80 1.1 Weight with 1 m stroke [g] 8 H40-L 060 1640 0 0 0 61 to 19 Max. stroke 500 H40-D 060 1640 19 to 1558 Working temperature from -0 to + 80 Tab. 104 Tab. 105 or the calculation of the allowed moments, please see pages L-5ff U-56

Uniline ystem H55 H55 system lider troke* L, J Y K X H D 8, 16,5 9 * The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. 84 * nom min max D H J K X Y troke** H55 55 71 70.4 7. 5 15 1.5 5 00 8 1 1 070 Tab. 106 * Including long or double slider. ee chapter Product dimensions s...l and...d ** Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 108 H55 0ax Technical data H55 U M x [] 0rad [] H55 460 175 M z 0ax [] M y M x [m] M y [m] 0rad M z [m] 54.5 ig. 85 H55-L 850 450 0 0 0 9 to 65 H55-D 850 450 65 to 6677 Working temperature from -0 to + 80 Tab. 107 Tab. 108 or the calculation of the allowed moments, please see pages L-5ff Max. traversing speed [m/s] 5 Max. acceleration [m/s²] 15 Repeat accuracy 0.1 Linear accuracy 0.8 ompact Rail guiding rail lider type ULV8 8 spec. Moment of inertia Iy [cm 4 ] 4.6 Moment of inertia Iz [cm 4 ] 41.7 Mass of slider [g] 475 Weight with zero stroke [g] 1460 Weight with 1 m stroke [g] 457 Max. stroke 5500 U-57

5 Uniline H series H75 H75 system lider troke* L, J Y K X H D 8, 16,5 9 * The length of the safety stroke is provided on request according to the customer's specifi c requirements. ig. 86 * nom min max D H J K X Y troke** H75 75 90 88.6 9.5 5 0 5 65 85 6 14.5 1 40 Tab. 109 * Including long or double slider. ee chapter Product dimensions s...l and...d ** Maximum stroke for a single-piece guiding rail. or longer strokes, see tab. 111 H75 0ax Technical data H75 M x [] 0rad [] H75 180 5500 M z 0ax [] M x [m] M y [m] M z [m] 09 ig. 87 H75-L 4560 11000 0 0 0 85 to 8 H75-D 4560 11000 88 to 18788 Tab. 110 M y or the calculation of the allowed moments, please see pages L-5ff 0rad Max. traversing speed [m/s] 7 Max. acceleration [m/s²] 15 Repeat accuracy 0.1 Linear accuracy 0.8 ompact Rail guiding rail ULV4 lider type 4 spec. Moment of inertia Iy [cm 4 ] 17 Moment of inertia Iz [cm 4 ] 17 Mass of slider [g] 14 Weight with zero stroke [g] 4160 Weight with 1 m stroke [g] 981 Max. stroke 7500 Working temperature from -0 to + 80 Tab. 111 U-58

Uniline ystem Lubrication The raceways of the guide rails in the Uniline linear axes are prelubricated. To achieve the calculated service life, a lubrication film must always be present between the raceway and the roller. The lubrication film also provides anticorrosion protection to the ground raceways. n approximate value for the lubrication period is every 100 km or every six months. The recommended lubricant is a lithium-based roller bearing grease of medium consistency. Lubrication of the raceways Proper lubrication under normal conditions: reduces friction reduces wear reduces stress on the contact faces reduces running noise Lubricants Thickeners Temperature range [ ] Dynamic viscosity [mpas] Roller bearing grease Lithium soap -0 to +170 <4500 Tab. 11 Relubrication of the guide rails These types of rails have a lubricating conduit on the side of the slider plate through which the lubricant can be applied directly to the raceways. Lubrication can be done in one of two ways: The advantage of this solution is the possibility of rail re-lubrication without machine downtime. *(ny adapter that may be necessary must be manufactured on site) 1. Relubrication using a grease gun: This is done by inserting the tip of the grease gun into the conduit at the slider plate and injecting the grease inside (see fig. 88). Please note that the grease has to fill the whole conduit in order to lubricate the rail properly; for this reason sufficient grease must be used.. utomatic lubrication system: To connect the unit to an automatic greasing system, use a proper adapter/connector* that attaches to the threaded hole on the side of the trolley. leaning the guide rails It is always recommended to clean the slider rail prior to any relubrication, in order to remove grease residues. This can be done while performing maintenance work or during a scheduled machine stop. ig. 88 U 1. lean the rail raceways with a clean and dry cloth. Ensure that all grease and dirt residues from previous work processes are removed. To ensure that the rails are cleaned over their entire length, the slider plate should be moved once over its entire length.. pply a sufficient amount of grease to the raceways. U-59

5 Uniline H series ccessories ixing brackets P- 5 5 4 ection - holes 4,5 6,5 ixing clamp for simple mounting of a linear axis on a mounting surface or for connecting two units with or without a connection plate (see pg. U-68). spacer* may be necessary. *(ny spacer that may be necessary must be manufactured on site) 8,5 0 7, 0 40 15 0 7,5 ig. 89 T-nut izes 40-75 ection - The maximum tightening torque is 10 m. 6 7,9 1,5 M6 16,5 ig. 90 ssembly kits T-connection plate P-1 T-connection plate allows two units to be mounted perpendicular to each other (see pg. U-65). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ote This adapter plate can be used with types E and ED only to a limited extent. or further information, please contact our pplication Engineering Department. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 165 55 55 6 6 5 5 4 1 6 6 1 1 5 4 5 1 150 luminum profile mounting side lider mounting side ig. 91 ize ixing holes for the slider ixing holes for the profile 40 Holes 1 Holes 4 55 Holes Holes 5 75 Holes Holes 6 Tab. 11 U-60

Uniline ystem ngle connection plate P- allows the right angle mounting of two units. The trolley of one unit can be mounted to the side of the other (see pg. U-66). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting to the linear units. ote This adapter plate can be used with types E and ED only to a limited extent. or further information, please contact our pplication Engineering Department. ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 7 8 75 8 1 6 5 lider mounting side luminum profile mounting side 4 1 1 165 6 5 1 ize ixing holes for the slider ixing holes for the profile 40 Holes 1 Holes 4 55 Holes Holes 5 75 Holes Holes 6 Tab. 114 ig. 9 X connection plate P- X connection plate for mounting two sliders perpendicular to each other (see pg. U-67). The plate will not interfere with the strokes of either unit. ll plates are delivered with M6 x 10 screws to DI 91 and T-nuts for mounting on the linear units. ize ixing holes for slider 1 ixing holes for slider 40 Holes 1 Holes 4 55 Holes Holes 5 75 Holes Holes 6 Tab. 115 160 5,5 55 ounterbore for M6 screw to DI 91 (for mounting in the slots of the nuts) 6 6 5 5 4 4 1 1 1 1 4 4 5 5,5 55 160 5 6 6 10 ig. 9 U U-61

Ordering key Ordering key Identification code for Uniline linear unit U H 07 04=40 05=55 07=75 1 1190 1 D 500 L 50 Indices of long slider plate see pg. U-56 - U-57 - U-58 Uniline prefi x ize Driving head code Ordering example: UH 07 1 1190 1 D 500 L 50 Indices of double slider plate, distance of the centers of slider plates see pg. U-56 - U-57 - U-58 Profi le/rail code L= Total length of the unit see pg. U-56 - U-57 - U-58 In order to create identifi cation codes for ctuator Line, you can visit: http://configureactuator.rollon.com U-6

Uniline ystem elt tension ll Uniline linear axes are all supplied with a standard belt tension suitable for most applications (see tab. 116). ize 40 55 75 ED75 100 elt tension [] 160 0 800 1000 1000 Tab. 116 ig. 94 The belt tensioning system (located at the ends of the slider plates for sizes 45 to 75, and at the deflection head for size 100) allows the toothed belt tension to be set in accordance with requirements. 400 00 ize 40 ize 55 To set the belt tension for sizes 40 to 75, the following steps must be followed (the reference values are standard values): 1. Determine the deviation of the belt tension from the standard value.. igures 95 and 96 show how many turns the belt tensioning screws must be for the required belt tension deviation.. alcualte the length of the belt (m), with the formula: L = x stroke (m) + 0.515 m (size 40); L = x stroke (m) + 0.60 m (size 55); L = x stroke (m) + 0.79 m (size 75). 4. Multiply the number of turns (see step ) by the toothed belt length m (see step ) to calculate the required number of turns to achieve the new desired belt tension.. 5. Unscrew the safety screw. 6. Turn the belt tensioning screws in accordance with the above explanation. Re-tighten the safety screw. elt tension [] elt tension [] 00 100 0 0 1500 1000 500 0 0 0,5 1 1,5 Turns of the belt screw per metre of toothed belt [U/m] Turns of the belt screw per metre of toothed belt [U/m] ig. 95 ize 75 0,5 1 1,5 U ig. 96 Example: Increasing the belt tension from 0 to 0 for an 55-1070: 1. deviation = 0-0 = 110.. igures 95 and 96 show that the value by which the belt tensioning screws must be turned to increase the belt tension by 110 is 0.5 turns.. ormula for calculating the toothed belt length: L = x stroke (m) + 0.60 m = x 1.070 + 0.60 =.77 m. 4. This means that the required number of turns is: 0.5 rpm x.77 m = 1.4 turns. 5. Unscrew the safety screw. 6. Turn the belt tensioning screws by 1.4 turns with the aid of an external reference. 7. Re-tighten the safety screw. U-6

6 elt tension To set the belt tension for size 100, the following steps must be followed (the reference values are standard values): 1. Determine the deviation of the belt tension from the standard value.. igure 97 shows how far the belt deflection pulley must be offset at the deflection head via the set screws, in order to obtain the desired belt tension.. Multiply the offset by the stroke length. 4. Turn the set screws in accordance with the above explanation. ig. 97 elt tension 100 000 1500 elt tension [] 1000 500 0 0 0,5 1 1,5 Offset of the belt deflection pulley in mm per metre of stroke ig. 98 Example: Increasing the belt tension from 1000 auf 1500 for an 100-000: 1. Deviation = 1500-1000 = 500.. The graphic shows that the offset of the belt deflection pulley required for increasing the belt tension by 500 is 0.5 mm per metre of stroke. Offset = 0.5 mm x (stroke) = 1 mm ote: If the linear unit is used such that the load acts directly on the toothed belt, it is important not to exceed the specified values for the belt tension. Otherwise, the positional accuracy and stability of the toothed belt cannot be guaranteed. If higher values are required for the belt tension, please contact our pplication Engineering Department. U-64

Uniline ystem Installation instructions Motor adapter plates and 1-P, sizes 40-75 To connect the linear units to the motor and gearbox, suitable adapter plates must be used. Rollon offers these plates in two different designs (see chapter ccessories), except for size 100. The standard plates are already provided with the holes required for mounting to the linear unit. The fixing holes must be made on site. Ensure that the mounted plate will not interfere with the stroke of the traversing slider plate. ig. 99 onnection to motor and gearbox 1. ttach the motor adapter plate to the motor or gearbox.. onnect the T-nuts by inserting the screws without tightening them and align the nuts in parallel to the slots of the unit.. Insert the connecting shaft into the drive head by aligning the key in the key slot. 4. ttach the motor adapter plate to the drive head of the linear axis by means of nuts and make sure that the nuts in the slots were rotated by 90 (see ccessories). Ensure correct fit of the adapter plate. ote: The connecting plates for the Uniline 40 are delivered with four fixing holes, even though only two holes are required for the connection. The presence of four holes give the plate a symmetric design which allows it to be used on any side of the unit. Due to the constructive design of the aluminum profile, only three fixing holes can be used the for the Uniline series. (see pg. U-, fig. ). T-connection plate P-1, sizes 40-75 onnection of two linear axes is achieved by means of the T-connection plate P-1 (see chapter ccessories). To mount the above-mentioned configuration, the following steps should be carried out: 1. Prepare the connection plate by inserting the screws into the existing holes on the P-1 (see fig. 100).. onnect the T-nuts by introducing the screws without tightening them and align the nuts in parallel to the slots of the unit.. Place the plate against the long side of unit 1 and tighten the screws. Ensure that the nuts in the slots were rotated by 90. 4. To fasten the plate to unit, insert the screws from the the long side of unit 1 (see fig. 101). 5. onnect the T-nuts by introducing the screws without tightening them and align the nuts in parallel to the slots of the slider plate of unit. 6. Place the plate against the slider plate and tighten the screws. Important: Please make sure that the nuts in the slots were rotated by 90. 1 ig. 100 1 U ig. 101 U-65

7 Installation instructions Example 1: ystem consisting of X-axes and 1 Y-axis The connection of the two units is attained by means of the parallel slider plates and the drive heads. or this configuration, we recommend using our connection plate P-1. ig. 10 ngle connection plate P-, sizes 40-75 onnection of two linear axes is achieved by means of the angle connection plate P-. To mount the above-mentioned configuration, the following steps should be carried out: 1. Insert the screws to be used for the connection to unit 1 into the prepared holes (see fig. 10).. onnect the T-nuts by inserting the screws without tightening them and align the nuts in parallel to the slots of the slider plates.. Place the connection plate against the slider plate and tighten the screws. Ensure that the nuts in the slots were rotated by 90. 4. To fix the connection plate to unit, insert the screws into the prepared holes on the short plate side (see fig. 104). 5. onnect the T-nuts by inserting the screws without tightening them and align the nuts in parallel to the slots of the aluminum profile of unit. 6. Place the connection plate against the slider plate and tighten the screws. Ensure that the nuts in the slots were rotated by 90. 1 ig. 10 1 ig. 104 Example ystem consisting of 1 X-axis and 1 -axis With this configuration, the -axis is connected to the slider plate of the X-axis by means of the angle connection plate P-. U-66 ig. 105

Uniline ystem X connection plate P-, sizes 40-75 onnection of the two linear axes is achieved by means of the X connection plate P- (see chapter ccessories). To mount the above-mentioned configuration, the following steps should be carried out: 1. Insert the screws from one side of the connection plate into the prepared holes (see fig. 106).. onnect the T-nuts by inserting the screws without tightening them and align the nuts in parallel to the slots of the slider plate of unit 1.. Place the connection plate against the slider plate and tighten the screws. Ensure that the nuts in the slots were rotated by 90. 4. Insert the screws from the other side of the connection plate (see fig. 107). 5. onnect the T-nuts by inserting the screws without tightening them and align the nuts in parallel to the slots of the slider plate of unit. 6. Place the connection plate against the slider plate and tighten the screws. Ensure that the nuts in the slots were rotated by 90. 1 1 ig. 106 ig. 107 Example ystem consisting of X-axes, 1 Y-axis and 1 -axis onnect four linear units to create a -axis gantry. The vertical axis is arranged to be self-supporting on the central unit. To do so, connect the two slider plates to each other, using the X connection plate P-. The connection of the two parallel axes to the central unit is attained by means of the T-connection plate P-1. U ig. 108 U-67

7 Installation instructions ixing clamp P-, sizes 40-75 onnection of two linear axes is achieved by means of the fixing clamps P- (see chapter ccessories). To mount the above-mentioned configuration, the following steps should be carried out: 1. Insert the fastening screws into the clamp and, if necessary, place a spacer* between the clamp and the slider plate. *(ny spacer that is to be used must be manufactured on site). onnect the T-nuts by inserting the screws without tightening them and align the nuts in parallel to the slots of the slider plates.. Insert the projecting part of the clamp into the lower slot of the aluminum profile of unit 1. 4. Position the clamp lengthwise according to the desired position of the slider plate of unit. 5. Tighten the fastening screws. Ensure that the nuts in the slots were rotated by 90. 6. Repeat this operation for the required number of fixing clamps. 1 ig. 109 Example 4 ystem consisting of 1 Y-axis and -axes The connection of the Y-axis to the parallel slider plates is attained via the fixing clamps P-. ig. 110 U-68