The HB Series Advantage SGS listed cnfirming t UL Standard 2108 & 8750 Certified t CSA Standard C22.2 N.9 LED Life f 50K+ hurs, under nrmal perating cnditins Lw wattage, lw heat, lw vltage (12DVC & 24VDC as indicated) Prvide cnsistent and unifrm illuminatin Emits n UV r infrared light and des nt cntain lead, mercury r glass Ec-friendly handling and dispsal when required Available in RGB r custms ptins Available in Fld r Narrw beam angles in cnfiguratin lengths Set up fr integrating using DMX, r ther cntrl prtcl systems Suitable fr wet lcatins, IP67 Simple user friendly installatin Tp quality cnnectrs and munting hardware Zer warm-up time and n reductin t lamp life in nrmal perating cnditins HIGH POWER RGB LED SERIES Architectural Illuminatin Systems Fr mre infrma-n, please visit ledpwer.cm r call 949.679.0031 Cpyright 2013 LED Pwer Inc. All rights reserved
LED Light Bar Part Numbers Length LEDs View Angle Vltage WaL/Bar (Nrmal) HB4010- RGB- 120 HB40LP- 10- RGB- 120 HB4019- RGB- 120 HB40LP- 19- RGB- 120 HB4028- RGB- 120 HB40LP- 28- RGB- 120 HB4037- RGB- 120 HB40LP- 37- RGB- 120 HB4046- RGB- 120 HB40LP- 46- RGB- 120 HB4019- RGB- 120 HB40LP- 19- RGB- 120 HB4037- RGB- 120 HB40LP- 37- RGB- 120 10.00 9 15 0, 25 0, 120 0 12VDC 10.8W 60W 19.00 18 15 0, 25 0, 120 0 12VDC 21.6W 60W 28.00 27 15 0, 25 0, 120 0 12VDC 32.4W 60W 37.00 36 15 0, 25 0, 120 0 12VDC 43.2W 60W 46.00 45 15 0, 25 0, 120 0 12VDC 54W 60W 19.00 18 15 0, 25 0, 120 0 24VDC 21.6W 96W 37.00 36 15 0, 25 0, 120 0 24VDC 43.2W 96W WaL/Run (Max) SPECIFICATIONS HB RGB LED Bar High Prfile HB High Prfile HB RGB LED Bar Lw Prfile HB Lw Prfile Fr mre infrma-n, please visit ledpwer.cm r call 949.679.0031 Cpyright 2013 LED Pwer Inc. All rights reserved
LED Light Bar Interface Cntrller Part Numbers Descrip-n Dimensin Input Vltage AC- MP MINI DCI- DMX AU03- F/AU03- DMX AC05 Preprgrammed Mini Cntrller DMX Addressable Interface Slave Cntrller/DMX Addressable Cntrller Preprgrammed Cntrller with 12 Shws Output Pwer Output Current 7 x1.75 x1.5 12V DC/24 V DC 36W 3Amp 7 x1.75 x1.5 12V DC/24 V DC 60W @ 12V DC 96W @ 24V DC 7.5 x5 x2 12V DC/24 V DC 60W @ 12V DC 96W @ 24V DC 7.5 x5 x2 12V DC/24 V DC 60W @ 12V DC 96W @ 24V DC 6Amp 6Amp 6Amp SPECIFICATIONS DCI-DMX AC-MP MINI Interface Cntrller Adjustable Bracket Accessries Part Numbers Descrip-n HB40 Flat Bracket Flat Bracket Flat Bracket End Cap HB Cap Male End Cap HB40 AdjBracket Adjustable Bracket HB40 LTW24 M&F- 4 M/F 4 pin 24 Jumper Wire Cable 4 Pin Female Starter Feed Wire Cable HB40 LTW48 M&F- 4 HB40 LTW12 FE- 4P M/F 4 pin 48 Jumper Wire Cable 12 4 pin Female Starter Feed * Other Jumper and Starter Feed wire sizes available Cntact LED Pwer fr p_n and pricing M/F 4 Pin Jumper Wire Cable Fr mre infrma-n, please visit ledpwer.cm r call 949.679.0031 Cpyright 2013 LED Pwer Inc. All rights reserved
LED Light Bar Pwer Supply Part Numbers Descrip-n Dimensin Input Vltage PS- Dimmable- 16192 PS- LED120A- 0012V- 50F PS- LEDINTA0024V41FO PS- LED1003R15X3 (Op_nal) 60W MAGNETIC Pwer Supply 60W Electrnic Pwer Supply 100W ELECTRONIC Pwer Supply NEMA Enclsure (Op_nal) 7 x3 x4 120/240 /277 9.5 x1.5 x 1.2 9.5 x1.5 x 1.2 13.4 x2.75 x2.32 Output Pwer 60W@12V DC 60W@24V DC Output Current 5Amp @ 12V DC 2.5 Amp @ 24V DC 120 60W@12V DC 5Amp @ 12V DC 120/240 /277 96W@24V DC 4.1 Amp - - - SPECIFICATIONS 100W Electrnic Pwer Supply NEMA Enclsure 60W Magnetic Pwer Supply PREPARE ELECTRICAL WIRING Electrical Requirements This RGB Clr Changing lighting system is supplied with an apprpriate pwer supply driver unit; this appliance unit must be supplied with 120V, 60Hz. and cnnected t an individual prperly grunded branch circuit, prtected by a 15 r 20. Amp circuit breaker r time delay fuse. The HB RGB LED Light Bar is a CLASS 2, 12 VDC r 24VDC as indicated, lw vltage luminary and must be used with an apprpriate pwer supply driver unit. Failure t cnnect this lighting system crrectly will vilate all warranty claims. Wiring must be 2 wires with grund and rated fr 75 C (176 F). NOTE: Cnsult lcal building cdes and guidelines n selecting wires. Wires must be UL Listed. Grunding Instructins-Cable Direct This lighting system must be cnnected t a grunded metal, permanent wiring system, r an equipment grunding cnductr must be run with the circuit cnductrs and be cnnected t the equipment grunding terminal. Fr mre infrma-n, please visit ledpwer.cm r call 949.679.0031 Cpyright 2013 LED Pwer Inc. All rights reserved
HB RGB INSTALLATION Flat Bracket Adjustable Bracket Munting Light Fixture with Munting Clips Munting clips, whether flat r rtating adjustable type, must be munted t a flat surface using apprpriate screws r ther fasteners. See the munting clip diagrams Lck ut and tag ut the circuit breaker fr the lighting circuit f the area where the LED light fixtures are being installed. Turn the light switch t ff t ensure n pwer is active. Remve any hazards in rder t access the electrical raceway r necessary space. Use a Vltmeter and check that there is n vltage. Remve any existing fixtures, wiring harnesses, etc. Remve any Ballast r ther pwer supplies frm the electrical raceway r necessary space. Wear glves t prevent injury when handling the ld materials such as reflectrs, ballasts, etc. MOUNTING LIGHT FIXTURE FOR YOUR SAFETY Read and bserve all CAUTIONS and WARNINGS shwn thrughut these instructins. While perfrming installatin described, glves, safety glasses r gggles shuld be wrn. Fr mre infrma-n, please visit ledpwer.cm r call 949.679.0031 Cpyright 2013 LED Pwer Inc. All rights reserved 3-60-381 Adjustable Bracket
Ntes Applicable Unless Otherwise Specified BEFORE YOU BEGIN Read these instructins cmpletely and carefully. WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR INJURY, OBSERVE THE FOLLOWING: A. Use these fixtures nly in the manner intended by the manufacturer. If yu have any questins, cntact the manufacturer. B. Befre servicing r cleaning unit, switch pwer ff at the service panel and fllw apprpriate lck ut/tag ut safety prcedures. HB RGB INSTALLATION Cnnect LED Pwer Supply Munt the LED pwer supply in the electrical raceway r as near as pssible; r where the previus flurescent ballast was lcated. Pwer supply has 120V 50/60HZ input (primary) and 12V DC r 24V DC utput (secndary). Using the apprpriate wiring diagram cnnect the riginal lad and neutral wires t the LED pwer supply input wires (black and white wire) using apprved cnnectin methd. As indicated, Munt ne (1) DMX r ther interface cntrller mdule per ne (1) pwer supply in clse prximity t the LED Pwer Supply. Prir t installing LED Luminary, please check vltage frm the Pwer Supply t ensure prper vltage. Install LED Luminary int the munting clips and tighten the small screws t hld the luminary in place. Fasten each luminary t the munting clip. If using rtating adjustable clip, adjust the luminary as need and tighten the large screws n either side f the clip. Cnnect the LED Luminary male utput cnnectr t the female cnnectr first cable ging t the cntrller. Cnnect the wires frm the the cntrller, t the wires that are cming ut f the 24V DC (secndary) utput f the pwer supply, using apprved cnnectrs fr the applicatin. Cnnect the DMX wires t the keypad cntrller & cnnect the apprpriate pwer supply t the keypad as necessary fllwing the keypad instructins. HB SERIES WIRING DIAGRAM HB SERIES RGB WIRING DIAGRAM FOR YOUR SAFETY Read and bserve all CAUTIONS and WARNINGS shwn thrughut these instructins. While perfrming installatin described, glves, safety glasses r gggles shuld be wrn. Fr mre infrma-n, please visit ledpwer.cm r call 949.679.0031 Cpyright 2013 LED Pwer Inc. All rights reserved
CAUTION The LED POWER HB RGB BAR LED luminary MUST be installed with the LED POWER SUPPLY specified r apprved by LED Pwer, Inc. fr this luminary. NOTE: LED Pwer, Inc. LED light fixtures are plarity sensi-ve. If the fixtures d nt light up, the wires may need t be reversed. HB RGB INSTALLATION * Nte: Keypad Cntrller shwn in diagram refers t all r any generic brand and is fr reference nly as part f the set up. Keypad Cntrller * (Any Generic Type) Cnnect LED Pwer Supply Additinal cnductrs may be needed t cnnect the pwer supply t the existing wiring in the raceway r ther sectin. Use cnductrs f prper size and rating as per lcal and natinal cdes. The LED pwer supply enclsure case includes a terminal fr grunding the incming 120V 50/60HZ grund wire. Attach LED pwer supply t a grund pint in the case either directly with a screw, r by using a green wire t attach t a remte grund pint. When using the DCI cntrl mdule, cnnect remaining wires by fllwing the wiring diagram prvided in rder t cnnect the LED Luminary t the DCI cntrl mdule Cnnect the DCI dimming cntrl mdule t the LED pwer supply by fllwing the wiring diagram prvided. Multiple DCI units can be cnnected t a single keypad cntrller. Cntact LED Pwer fr ther keypad cntrller ptins. DMX Cntrller with Keypad Op_n Wiring Diagram FOR YOUR SAFETY Read and bserve all CAUTIONS and WARNINGS shwn thrughut these instructins. While perfrming installatin described, glves, safety glasses r gggles shuld be wrn. Fr mre infrma-n, please visit ledpwer.cm r call 949.679.0031 Cpyright 2013 LED Pwer Inc. All rights reserved
* Nte: Keypad Cntrller shwn in diagram refers t all r any generic brand and is fr reference nly as part f the set up. HB RGB INSTALLATION Keypad Cntrller * (Any Generic Type) Cnnect LED Pwer Supply When using DMX integrated pwer supplies, cnnect DMX Dial r keypad cntrller directly t the pwer supply. Duble check yur wiring methds and vltage with a meter at the end f each run t be sure that all wires are prperly cnnected with suitable cnnectrs and that there is n vltage drp. Remve the lck ut tag frm the circuit breaker fr the lighting circuit and turn the breakers back n Turn the lights back n t the case and inspect all lights t ensure that they are functining prperly. HB SERIES WIRING DIAGRAM ** Please cnsult with Prfessinal DMX prgrammer r Keypad Cntrller Suppliers fr infrma=n n Keypad Cntrl set up and prgramming. DMX Integrated Pwer Supply Wiring Diagram With DMX Cntrller FOR YOUR SAFETY Read and bserve all CAUTIONS and WARNINGS shwn thrughut these instructins. While perfrming installatin described, glves, safety glasses r gggles shuld be wrn. Fr mre infrma-n, please visit ledpwer.cm r call 949.679.0031 Cpyright 2013 LED Pwer Inc. All rights reserved