ASTRO ATS-9900 TABBER, LABELER, AND STAMP AFFIXER. Parts Manual

ASTRO ATS-9900 TABBER, LABELER, AND STAMP AFFIXER Parts Manual

This manual is intended solely for the use and information of Astro Machine Corp. its designated agents, customers, and their employees. The information in this guide was obtained from several different sources that are deemed reliable by all industry standards. To the best of our knowledge, that information is accurate in all respects. However, neither Astro Machine Corp. nor any of its agents or employees shall be responsible for any inaccuracies contained herein. All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or any information storage and retrieval system, without permission in writing from the publisher.

TABLE OF CONTENTS GROUP 1 Tab Reel and Head Assembly 1 GROUP 1A Tab Reel Assembly 3 GROUP 1B Head Assembly 5 GROUP 1C Label Head Assembly 7 GROUP 1D Tab Applicator Assembly 8 GROUP 2A Tabber Body 9 GROUP 2B Tabber Body New Style* 11 GROUP 2C Tabber Body Assemblies 13 GROUP 3A Applicator Head Assembly 15 GROUP 3B Applicator Head Assembly New Style* 17 GROUP 4A Head Support Mechanism 19 GROUP 4B Head Support Mechanism New Style* 21 GROUP 4C Short Media Kit 23 GROUP 5A Drive and Transport 25 GROUP 5B Drive and Transport New Style* 27 GROUP 6 Transport Section 29 GROUP 7 Head Raising Mechanism 31 GROUP 8 Main Frame 33 GROUP 9 Base Electrical (115/120V) 35 GROUP 9A Base Electrical (220V) 37 GROUP 9B 220V Transformer & Components 39 GROUP 10 Rear Cover 40 GROUP 11 Control Panel 42 GROUP 12 Terminal Block 44 GROUP 13 Feeder Guide Kit 46 INDEX 47 *NOTE: To determine if you have a "New Style" unit, look for the following: 1. Wheel assemblies attached to the underside of the Applicator Head Assembly Cover (See Group 3B, #14). 2. A second set of Rollers at the exit end of the Tabber (See Group 5B, #16)

GROUP 1 TAB REEL AND HEAD ASSEMBLY 1

GROUP 1 TAB REEL AND HEAD ASSEMBLY 1. 123-0011 SCREW, 1/4-20 x 1 SOC. HD CAP, BLACK 2 2. 123-0064 LOCK WASHER, 1/4, SS 1 3. 123-0182 SCREW, 1/4 x 20 x 3/4 SOC. HD. CAP, BLACK 1 4. 123-0278 LOCK WASHER, 1/4 INTERNAL TOOTH 1 5. 123-0524 SCREW, 1/4 x 1/2 SOC. HD. CAP 3 6. DOUBLE TABBER ASSEMBLY (SEE GROUP 2A OR 2B) 1 7. 33-220-02 HEAD ASSEMBLY 1 8. 33-225-02 REEL ASSEMBLY 1 2

3 GROUP 1A TAB REEL ASSEMBLY

GROUP 1A TAB REEL ASSEMBLY 1. 33-500-78 BRAKE 12V 1 2. 33-125-24 KEY 1 3. 33-225-23 SUPPLY POST COVER 1 4. 33-125-19 SUPPLY GUIDE ASSEMBLY 1 5. 33-125-18 STAND OFF 4 6. 33-125-13 BEARING HOUSING 1 7. 33-125-12 ROLL GUIDE 4 8. 33-125-11 ROLL GUIDE 1 9. 33-125-08 SUPPLY HUB 1 10. 33-125-07 SUPPLY SHAFT 1 11. 33-125-06 SUPPLY PLATE 1 12. 33-225-04 SUPPLY POST 1 13. 123-2062 SCREW, 10-32 x 7/16 SOC. HD. CAP SS, BLACK 4 14. 123-1650 C-CLIP, RETAINING 0.500 x 1/2 x 0.461 DIA. 2 15. 123-1210 SCREW, 10-32 x 3/8 BTN. HD. SOC. CAP 4 16. 123-1204 SCREW, 6-32 x 1/4 BTN. HD. SOC. CAP SS, BLACK 1 17. 123-1161 SET SCREW, 1/4-20 x 3/8 CUP PT. 1 18. 123-0324 BEARING, NICE 1816 DS 1 * 33-113-17 FANFOLD TRAY (FOR LABELS UP TO 5" LONG) 1 * 33-117-31 FANFOLD TRAY (FOR LABELS OVER 5" LONG) 1 *NOT SHOWN 4

GROUP 1B HEAD ASSEMBLY 5

GROUP 1B HEAD ASSEMBLY 1. 33-500-77 MOTOR, REWIND ASSEMBLY 1 2. 33-500-144 SERVO MOTOR ASSEMBLY 1 3. 33-500-134 PAPER LOOP SENSOR ASSEMBLY 1 4. 33-126-15 STANDOFF 3 5. 33-126-13 WASTE TAKE UP SUPPORT ASSEMBLY 1 6. 33-122-35 MOTOR, UNWIND 1 7. 33-122-27 TAB GUIDE ASSEMBLY 1 8. 33-122-22 IDLER ROLLER 3 9. 33-122-19 LABEL SUPPLY ROLLER 1 10. 33-122-11 LOOP GUIDE ASSEMBLY 1 11. 33-122-06 IDLER ROLL ASSEMBLY 2 12. 33-121-15 FRONT COVER 1 13. 33-121-14 BOTTOM COVER 1 14. 33-121-12 TOP COVER 1 15. 33-121-08 TAB DRIVER WHEEL ASSEMBLY 1 16. 33-220-20 HEAD TOP COVER 1 17. 33-120-07 HEAD SIDE FRAME, REAR 1 18. 33-112-01 TAB APPLICATOR SENSOR AND WIRING HARNESS 2 18A. 33-113-03 LABEL HEAD ASSEMBLY (SEE GROUP 1C) 1 18B. 33-111-03 TAB APPLICATOR HEAD ASSEMBLY (SEE GROUP 1D) 1 19. 123-0011 SCREW, 1/4-20 x 1 SOC. HD. CAP SS BLACK 2 20. 33-126-17 DRIVE SPOOL 1 20.1 123-0757 SET SCREW, 6-32 x 1/4 STD. CUP PT. 1 21. 123-1085 O-RING, CLEAR 3 22. 33-120-15 SWITCH HOLDER ASSEMBLY 1 22.1 33-120-16 SWITCH HOLDER 1 22.2 123-0988 MICRO SWITCH 2 22.3 123-2030 SCREW, 4-40 x 1 PAN HD. PH 2 6

GROUP 1C LABEL HEAD ASSEMBLY 33-113-03 LABEL HEAD ASSEMBLY (INCLUDES ALL PARTS LISTED BELOW) 1 1. 123-0004 SCREW, 10-32 x 5/8, SOC. HD. CAP, BLACK 2 2. 123-0191 WASHER, #6 PLAIN 2 3. 123-0267 SCREW, 6-32 x 5/16 SOC. HD. CAP, SS (USE RED LOCTITE) 1 4. 123-0524 SCREW, 1/4 x 1/2 SOC. HD. CAP 2 5. 123-0612 SCREW, 6-32 x 1/4 PAN HD. PH. SS 1 6. 123-0975 SCREW, 4-40 x 1/4 PH, FH SS 2 7. 123-1677 LOCK WASHER, #10 SS 2 8. 33-111-05 TAB APPLICATOR HOLDER 1 9. 33-111-08 SENSOR COVER 1 10. 33-111-11 TOP APPLICATOR SPACER 1 11. 33-111-12 SENSOR BRACKET 1 12. 33-111-13 TOP APPLICATOR SPACER 1 13. 33-112-01 TAB APPLICATOR SENSOR AND WIRING HARNESS 1 14. 33-112-15 SENSOR SCREW 1 15. 33-113-07 LABEL SEPARATOR 1 16. 33-113-10 LABEL GUIDE 1 7

GROUP 1D TAB APPLICATOR ASSEMBLY 33-111-03 TAB APPLICATOR ASSEMBLY (INCLUDES ALL PARTS LISTED BELOW) 1 1. 123-0004 SCREW, 10-32 x 5/8, SOC. HD. CAP, BLACK 2 2. 123-0191 WASHER, #6 PLAIN 2 3. 123-0267 SCREW, 6-32 x 5/16 SOC. HD. CAP, SS (USE RED LOCTITE) 1 4. 123-0524 SCREW, 1/4 x 1/2 SOC. HD. CAP 2 5. 123-0975 SCREW, 4-40 x 1/4 PH, FH SS 2 6. 123-1677 LOCK WASHER, #10 SS 2 7. 33-111-05 TAB APPLICATOR HOLDER 1 8. 33-111-07 TAB SEPARATOR 1 9. 33-111-08 SENSOR COVER 1 10. 33-111-10 TAB GUIDE 11. 33-111-11 TOP APPLICATOR SPACER 1 12. 33-111-12 SENSOR BRACKET 1 13. 33-111-13 TOP APPLICATOR SPACER 1 14. 33-112-01 TAB APPLICATOR SENSOR AND WIRING HARNESS 1 15. 33-112-15 SENSOR SCREW 1 8

GROUP 2A TABBER BODY 9

GROUP 2A TABBER BODY 1. 123-0017 SCREW, 10-32 x 1/4 TRUSS HD. PH SS 30 2. 123-0237 LOCK WASHER, #10 EXTERNAL TOOTH 16 3. 123-1178 SCREW, 6-32 x 1/4 FL. HD. PH, UNDERCUT 3 4. 123-1442 SCREW, 1/4-20 x 1/2 BTN. HD. SOC. CAP, SS 13 5. 123-1503 SCREW, 10-24 x 3/8 BTN. HD. SOC CAP SS, BLACK 2 6. 123-1790 BEARING, SNAP-IN 1/2" 1 7. 33-100-15 SUPPORT, EXIT ROLLERS 1 8. 33-104-05 CLOSURE, FRONT 1 9. 33-104-10 CENTER PLATE 1 10. HEAD SUPPORT MECHANISM & DRIVE AND TRANSPORT ASSEMBLY 1 (SEE GROUPS 4A, 5A) 11. 33-200-20 H-BRIDGE ASSEMBLY (SEE GROUP 9) 1 12. 33-200-30 CLOSURE, RIGHT-HAND FRONT 1 13. 33-200-31 CLOSURE, RIGHT-HAND REAR 1 14. 33-200-32 CLOSURE, LEFT-HAND FRONT 1 15. 33-200-33 CLOSURE, LEFT-HAND REAR 1 16. 33-200-38 CLOSURE, REAR TOP ASSEMBLY 1 17. 33-206-19 SIDE ADJUST WHEEL ASSEMBLY 1 10

GROUP 2B TABBER BODY NEW STYLE 11

GROUP 2B TABBER BODY NEW STYLE 1. 123-0017 SCREW, 10-32 x 1/4 TRUSS HD. PH SS 30 2. 123-0237 LOCK WASHER, #10 EXTERNAL TOOTH 16 3. 123-1178 SCREW, 6-32 x 1/4 FL. HD. PH, UNDERCUT 3 4. 123-1442 SCREW, 1/4-20 x 1/2 BTN. HD. SOC. CAP, SS 13 5. 123-1503 SCREW, 10-24 x 3/8 BTN. HD. SOC CAP SS, BLK 2 6. 123-1790 BEARING, SNAP-IN 1/2" 1 7. 33-100-15 SUPPORT, EXIT ROLLERS 1 8. 33-104-05 CLOSURE, FRONT 1 9. 33-104-10A CENTER PLATE 1 10. HEAD SUPPORT MECHANISM & DRIVE AND TRANSPORT ASSEMBLY 1 (SEE GROUPS 4B, 5B) 11. 33-200-20 H-BRIDGE ASSEMBLY (SEE GROUP 9) 1 12. 33-200-30 CLOSURE, RIGHT-HAND FRONT 1 13. 33-200-31 CLOSURE, RIGHT-HAND REAR 1 14. 33-200-32 CLOSURE, LEFT-HAND FRONT 1 15. 33-200-33 CLOSURE, LEFT-HAND REAR 1 16. 33-200-38 CLOSURE, REAR TOP ASSEMBLY 1 17. 33-206-19 SIDE ADJUST WHEEL ASSEMBLY 1 12

GROUP 2C TABBER ASSEMBLIES 13

GROUP 2C TABBER ASSEMBLIES 1. 33-109-02 REGISTRATION DEVICE ASSEMBLY 1 1.1 33-109-12 REGISTRATION DEVICE BLOCK ASSEMBLY 1 1.2 123-1503 SCREW, 10-24 x 3/8 SOC. CAP, BTN. HD. 2 1.3 123-1210 SCREW, 10-32 x 3/8 SOC. CAP, BTN. HD. 3 1.4 123-0017 SCREW, 10-32 x 1/4 TRUSS HD. PH (APPLY BLUE LOCTITE) 3 1.5 33-109-05 REGISTRATION DEVICE BODY 1 1.6 33-109-06 ARM HOLDER ASSEMBLY 3 1.7 97-115-02 WHEEL ASSEMBLY 3 2. 33-109-31 LEFT-HAND RETAINER SPRING ASSEMBLY 1 2.1 25-133-21 BRASS SCREW, 1/4-20, ASSEMBLY 1 2.2 25-116-34 RETAINER SPRING HOLDER ASSEMBLY 1 2.3 123-0053 STOP NUT, 10-32 NYLON INSERT 1 2.4 123-1210 SCREW, 10-32 x 3/8 SOC. CAP, BTN. HD 1 2.5 123-1206 SCREW, 10-32 x 1/4 SOC. CAP, BTN. HD. (APPLY BLUE LOCTITE) 1 2.6 33-109-35 RETAINER SPRING WELDMENT, LEFT-HAND 1 2.7 123-0169 C-CLIP, 1/4" CRESCENT 2 2.8 123-0035 BEARING, NMB R-4HH 1 2.9 33-109-39 RETAINER SPRING PIVOT 1 2.10 123-1135 SCREW, 6-32 x 1/4 TRUSS HD. (APPLY BLUE LOCTITE) 2 3. 33-109-32 RIGHT-HAND RETAINER SPRING ASSY. 1 3.1 25-133-21 BRASS SCREW, 1/4-20, ASSEMBLY 1 3.2 25-116-34 RETAINER SPRING HOLDER ASSEMBLY 1 3.3 123-0053 STOP NUT, 10-32 w/nylon INSERT 1 3.4 123-1210 SCREW, 10-32 x 3/8 SOC. CAP, BTN. HD. 1 3.5 123-1206 SCREW, 10-32 x 1/4 SOC. CAP, BTN. HD. (APPLY BLUE LOCTITE) 1 3.6 33-109-33 RETAINER SPRING WELDMENT, RIGHT-HAND 1 3.7 123-0169 C-CLIP, 1/4" CRESCENT 2 3.8 123-0035 BEARING, NMB R-4HH 1 3.9 123-1135 SCREW, 6-32 x 1/4 TRUSS HD. (APPLY BLUE LOCTITE) 2 3.10 33-109-39 RETAINER SPRING PIVOT 1 4.* 33-109-44 RETAINER SPRING EXTENSION ASSY. 1 4.1 84-114-05 THUMBSCREW ASSEMBLY, PLASTIC CAP 1 4.2 33-109-46 RETAINER SPRING HOLDER 1 4.3 123-0127 SCREW, 6-32 x 1/8 PAN HD. PH 2 4.4 33-109-48 RETAINER SPRING WELDMENT 1 4.5 123-0169 C-CLIP, 1/4" CRESCENT 2 4.6 123-0035 BEARING, NMB R-4HH 1 4.7 123-1135 SCREW, 6-32 x 1/4 TRUSS HD. (APPLY BLUE LOCTITE) 2 4.8 33-109-39 RETAINER SPRING PIVOT 1 *Optional Assembly 14

GROUP 3A APPLICATOR HEAD ASSEMBLY STRONGLY RECOMMENDED: REPLACE BEARINGS WHEN REPLACING ROLLER SHAFTS. 15

GROUP 3A APPLICATOR HEAD ASSEMBLY 1. 123-0017 SCREW, 10-32 x 1/4 TRUSS HD. PH. SS 4 2. 123-0374 SET SCREW, 10-32 x 1/4 SOC. HD. SS BLACK OXIDE 2 3. 123-1861 SET SCREW, 10-24 x 1/4 HEX SOC. CUP PT. 1 4. 123-2004 BELT, TIMING XL67 GROOVES 13.40L x 0.46 W x 1.5 PITCH 1 5. 33-100-56 SPRING HOOK 1 6. 33-101-28 PULLEY, 30 GROOVES 1 7. 33-101-43 ROLLER ASSEMBLY, HARD (INCLUDES LOCK SCREW) 4 7A. 33-101-51 LOCK SCREW FOR 33-101-43 HARD ROLLER ASSEMBLY 4 8. 33-101-46 ROLLER, SOFT ADJUSTABLE (INCLUDES SET SCREW) 2 8A. 123-2040 SET SCREW FOR 33-101-46 SOFT ADJUSTABLE ROLLER ASSEMBLY 2 9. 33-108-12 SPRING 1 10. 33-110-02 APPLICATOR HEAD ASSEMBLY 1 10.1 33-110-05 ARM ASSEMBLY, REAR (BEARINGS INCL.) 1 10.2 33-110-03 ARM ASSEMBLY, FRONT (BEARINGS INCL.) 1 10.3 28-104-13 BEARING ASSEMBLY 4 10.4 33-110-10 APPLICATOR ROLLER SHAFT 1 10.5 97-115-02 WHEEL ASSEMBLY 2 10.6 123-0008 SCREW, 10-32 x 1/2 BTN. HD. PH 2 11. 33-110-13 SHAFT, TOP EXIT 1 LOCK FLANGE ASSEMBLY KIT (INCLUDES ONE INTERCHANGEABLE LOCK FLANGE, 12. 33-900-20* LOCK KNOB AND 2 WASHERS) 2 *Replaces 33-110-21 Lever-style Handle Assembly 13. 33-110-11 FRONT COVER ASSEMBLY 1 13.1 33-110-08 FRONT COVER WELDMENT 1 13.2 123-0381 PULL HANDLE (INCLUDES SCREWS) 1 14. HEAD SUPPORT MECHANISM (SEE GROUP 4A) 1 14.1. 33-108-02 TENSIONER ASSEMBLY 1 14.2. 33-102-03 FRONT BRIDGE ASSEMBLY 1 14.3. 33-102-05 REAR BRIDGE ASSEMBLY 1 14.4. 33-110-33 MICRO SWITCH BRACKET ASSEMBLY 1 14.4.1 33-110-31 MICRO SWITCH BRACKET WELDMENT 1 14.4.2 33-110-17 STOPPER 1 14.4.3 123-0978 SCREW, 4-40 x 1/2 PAN HD. PH SS 2 14.4.4 123-0988 MICRO SWITCH 2 14.4.5 123-2030 SCREW, 4-40 x 1 PAN HD. PH 2 14.5. 33-110-35 STOPPER ASSEMBLY 1 14.6. 33-200-37 COVER, REAR TOP 1 15. 65-303-01 MOTOR PULLEY ASSEMBLY, 14 GROOVES 1 16. 123-0573 BELT 1 17. 33-900-10 EXIT ROLLER HEAD SAFETY COVER KIT 1 17.1 33-110-63 HEAD SAFETY COVER 1 17.2 123-0024 SCREW, 10-32 x 3/8 TRUSS HD. PH SS 1 17.3 33-110-67 WASHER, SAFETY COVER 1 16

GROUP 3B APPLICATOR HEAD ASSEMBLY NEW STYLE STRONGLY RECOMMENDED: REPLACE BEARINGS WHEN REPLACING ROLLER SHAFTS. 17

GROUP 3B APPLICATOR HEAD ASSEMBLY NEW STYLE 1. 123-0017 SCREW, 10-32 x 1/4 TRUSS HD. PH. SS 8 2. 123-0374 SET SCREW, 10-32 x 1/4 SOC. HD. SS BLACK OXIDE 2 3. 123-1861 SET SCREW, 10-24 x 1/4 HEX SOC. CUP PT 2 4. 123-2004 BELT, TIMING XL67 GROOVES 13.40L x 0.46 W x 1.5 PITCH 1 5. 33-100-56 SPRING HOOK 1 6. 33-101-28 PULLEY, 30 GROOVES 1 7. 33-101-43 ROLLER ASSEMBLY, HARD (INCLUDES LOCK SCREW) 4 7A. 33-101-51 LOCK SCREW FOR 33-101-43 HARD ROLLER ASSEMBLY 4 8. 33-101-46 ROLLER, SOFT ADJUSTABLE (INCLUDES SET SCREW) 4 8A. 123-2040 SET SCREW FOR 33-101-46 SOFT ADJUSTABLE ROLLER ASSEMBLY 4 9. 33-108-12 SPRING 1 10. 33-110-02 APPLICATOR HEAD ASSEMBLY 1 10.1 33-110-05 ARM ASSEMBLY, REAR (BEARINGS INCL.) 1 10.2 33-110-03 ARM ASSEMBLY, FRONT (BEARINGS INCL.) 1 10.3 28-104-13 BEARING ASSEMBLY 4 10.4 33-110-10 APPLICATOR ROLLER SHAFT 1 10.5 97-115-02 WHEEL ASSEMBLY 2 10.6 123-0008 SCREW, 10-32 x1/2 BTN. HD. PH 2 11. 33-114-23 SHAFT, TOP EXIT 1 LOCK FLANGE ASSEMBLY KIT (INCLUDES ONE INTERCHANGEABLE LOCK FLANGE, 12. 33-900-20* LOCK KNOB AND 2 WASHERS) 2 *Replaces 33-110-21 Lever-style Handle Assembly 13. 33-114-06 FRONT COVER ASSEMBLY 1 13.1 33-110-08 FRONT COVER WELDMENT 1 13.2 123-0381 PULL HANDLE (INCLUDES SCREWS) 1 13.3 123-0017 SCREW, 10-32 x 1/4 TRUSS HD. PH. SS 4 13.4 33-114-10 WHEEL ARM BRACKET ASSEMBLY 2 13.4.1 97-115-02 WHEEL ASSEMBLY 4 13.4.2 123-0008 SCREW, 10-32 x1/2 BTN. HD. PH 4 14. HEAD SUPPORT MECHANISM (SEE GROUP 4B) 1 14.1. 33-108-02 TENSIONER ASSEMBLY 1 14.2. 33-102-03 FRONT BRIDGE ASSEMBLY 1 14.3. 33-102-05 REAR BRIDGE ASSEMBLY 1 14.4. 33-110-33 MICRO SWITCH BRACKET ASSEMBLY 1 14.4.1 33-110-31 MICRO SWITCH BRACKET WELDMENT 1 14.4.2 33-110-17 STOPPER 1 14.4.3 123-0978 SCREW, 4-40 x 1/2 PAN HD. PH SS 2 14.4.4 123-0988 MICRO SWITCH 2 14.4.5 123-2030 SCREW, 4-40 x 1 PAN HD. PH 2 14.5. 33-110-35 STOPPER ASSEMBLY 1 14.6. 33-200-37 COVER, REAR TOP 1 15. 65-303-01 MOTOR PULLEY ASSEMBLY, 14 GROOVES 2 16. 123-0573 BELT 1 17. 33-900-10 EXIT ROLLER HEAD SAFETY COVER KIT 1 17.1 33-110-63 HEAD SAFETY COVER 1 17.2 123-0024 SCREW, 10-32 x 3/8 TRUSS HD. PH SS 1 17.3 33-110-67 WASHER, SAFETY COVER 1 18

GROUP 4A HEAD SUPPORT MECHANISM 19

GROUP 4A HEAD SUPPORT MECHANISM 1. 123-0011 SCREW, 1/4-20 x 1 SOC. HD. CAP SS 8 2. 123-0064 LOCK WASHER, 1/4 MED. SPLIT 8 3. 123-0182 SCREW, 1/4-20 x 3/4 SOC. HD. CAP BLACK 4 4. 123-0855 LOCK WASHER, 5/16 SS 4 5. 123-1382 SCREW, 5/16-18 x 1 SOC. HD. CAP ALLOY STEEL 2 6. 123-1630 SCREW, 5/16-18 x 1 SOC. HD. CAP SS BLACK 4 7. DRIVE AND TRANSPORT ASSEMBLY (SEE GROUP 5A) 1 8. 33-102-03 FRONT BRIDGE ASSEMBLY 1 9. 33-102-05 REAR BRIDGE ASSEMBLY 1 10. 33-102-07 CROSS BEAM, L/H 1 11. 33-102-08 CROSS BEAM, R/H 1 12. 33-102-10 SENSOR BEAM ASSEMBLY 1 13. 33-105-02 FRONT POST ASSEMBLY, R/H 1 14. 33-105-04 REAR POST ASSEMBLY, R/H 1 15. 33-105-06 POST ASSEMBLY, L/H 2 16. 33-105-09 MAIN CROSS BEAM 1 17. 33-105-14 BASE CROSS BEAM 2 18. 33-105-17 REAR CROSS BEAM 1 19. 33-105-18 BUSHING 1 20. 33-105-19 BUSHING 4 21. 33-110-33 MICRO SWITCH BRACKET ASSEMBLY 1 21.1 33-110-31 MICRO SWITCH BRACKET WELDMENT 1 21.2 33-110-17 STOPPER 1 21.3 123-0978 SCREW, 4-40 x 1/2 PAN HD. PH SS 2 21.4 123-0988 MICRO SWITCH 2 21.5 123-2030 SCREW, 4-40 x 1 PAN HD. PH 2 22. 33-110-35 STOPPER ASSEMBLY 1 23. 33-119-06 HEAD HUB ASSEMBLY 1 24. 33-200-36 COVER, FRONT TOP 1 25. 33-200-37 COVER, REAR TOP 1 26. 33-109-18 SENSOR #1 ASSEMBLY 1 27. 33-109-19 SENSOR #2 ASSEMBLY 1 28. 123-2033A SENSOR REFLECTOR 2 20

GROUP 4B HEAD SUPPORT MECHANISM NEW STYLE 21

GROUP 4B HEAD SUPPORT MECHANISM NEW STYLE 1. 123-0011 SCREW, 1/4-20 x 1 SOC. HD. CAP SS 8 2. 123-0064 LOCK WASHER, 1/4 MED. SPLIT 8 3. 123-0182 SCREW, 1/4-20 x 3/4 SOC. HD. CAP BLACK 4 4. 123-0855 LOCK WASHER, 5/16 SS 4 5. 123-1382 SCREW, 5/16-18 x 1 SOC. HD. CAP ALLOY STEEL 2 6. 123-1630 SCREW, 5/16-18 x 1 SOC. HD. CAP SS BLACK 4 7. DRIVE AND TRANSPORT ASSEMBLY (SEE GROUP 5B) 1 8. 33-102-03 FRONT BRIDGE ASSEMBLY 1 9. 33-102-05 REAR BRIDGE ASSEMBLY 1 10. 33-102-07 CROSS BEAM, L/H 1 11. 33-102-08 CROSS BEAM, R/H 1 12. 33-102-10 SENSOR BEAM ASSEMBLY 1 13. 33-105-02 FRONT POST ASSEMBLY, R/H 1 14. 33-105-04 REAR POST ASSEMBLY, R/H 1 15. 33-105-06 POST ASSEMBLY, L/H 2 16. 33-105-09 MAIN CROSS BEAM 1 17. 33-105-14 BASE CROSS BEAM 2 18. 33-105-17 REAR CROSS BEAM 1 19. 33-105-18 BUSHING 1 20. 33-105-19 BUSHING 4 21. 33-110-33 MICRO SWITCH BRACKET ASSEMBLY 1 21.1 33-110-31 MICRO SWITCH BRACKET WELDMENT 1 21.2 33-110-17 STOPPER 1 21.3 123-0978 SCREW, 4-40 x 1/2 PAN HD. PH SS 2 21.4 123-0988 MICRO SWITCH 2 21.5 123-2030 SCREW, 4-40 x 1 PAN HD. PH 2 22. 33-110-35 STOPPER ASSEMBLY 1 23. 33-119-06 HEAD HUB ASSEMBLY 1 24. 33-200-36 COVER, FRONT TOP 1 25. 33-200-37 COVER, REAR TOP 1 26. 33-109-18 SENSOR #1 ASSEMBLY 1 27. 33-109-19 SENSOR #2 ASSEMBLY 1 28. 123-2033A SENSOR REFLECTOR 2 22

GROUP 4C SHORT MEDIA KIT 23

GROUP 4C SHORT MEDIA KIT SM-9900 SHORT MEDIA KIT 1. 33-115-40 INPUT RETAINER SPRING ASSEMBLY 1 1.1. 25-133-21 BRASS SCREW, 1/4-20 ASSEMBLY 1 1.2. 25-116-34 RETAINER SPRING HOLDER ASSEMBLY 1 1.3. 123-1206 SCREW, 1-32 x 1/4 BTN. HD. SOC. CAP, (APPLY BLUE LOCTITE) 1 1.4. 123-1210 SCREW, 10-32 x 3/8 SOC. CAP BTN. HD. 1 1.5. 123-0053 NYLON INSERT STOP NUT, 10-32 1 1.6. 33-115-41 INPUT RETAINER SPRING 1 1.7. 123-0976 SCREW, 4-40 x 1/4 PH PAN HD. (APPLY RED LOCTITE) 2 1.8. 21-144-00 WHEEL ASSEMBLY 2 1.9. 123-0080 3/16 TRUARC, #5133-1B 4 1.10. 32-111-17 CARTRIDGE SHAFT 2 2. 33-115-44 EXIT RETAINER SPRING ASSEMBLY 1 2.1. 84-114-05 SHAFT, RUBBER ROLLER 1 2.2. 33-115-45 BRACKET, EXIT RETAINER SPRING 1 2.3. 123-0021 SCREW, 4-40 x 1/8 PH BTN. HD. (APPLY BLUE LOCTITE) 4 2.4. 33-115-46 REAR RETAINER SPRING ASSEMBLY 1 2.5. 33-115-48 FRONT RETAINER SPRING ASSEMBLY 1 24

GROUP 5A DRIVE AND TRANSPORT STRONGLY RECOMMENDED: REPLACE BEARINGS WHEN REPLACING ROLLER SHAFTS. 25

GROUP 5A DRIVE AND TRANSPORT 1. TRANSPORT SECTION (SEE GROUP 6) 1 1.1. 33-101-05 DRIVER ROLLER ASSEMBLY (SEE GROUP 6) 1 1.1.1. 33-101-29 PULLEY, 30 GROOVES 1 1.2. 33-101-30 ENCODER ASSEMBLY (INCLUDES 1.2.1, 1.2.2 & 1.2.3) 1 1.2.1. 123-2013 PULLEY, TIMING BELT, 33 GROOVE 1 1.2.2. 33-101-31 ENCODER BRACKET 1 1.2.3. 33-500-135 ENCODER 1 1.3. 33-101-55 BASE MOTOR ASSEMBLY 1 1.3.1. 33-101-47 MOTOR PULLEY SUBASSEMBLY, 12XL 1 2. 33-101-14 BOTTOM EXIT SHAFT ASSEMBLY 1 2.1. 123-0994 PULLEY, 40 DP 1 2.2. 33-101-29 PULLEY, 30 GROOVES 1 2.3. 33-101-15 BOTTOM EXIT SHAFT 1 2.4. 33-101-43 ROLLER ASSEMBLY, HARD (INCLUDES LOCK SCREW) 2 2.5. 33-101-42 ROLLER ASSEMBLY, SOFT (INCLUDES LOCK SCREW) 2 2.6 33-101-51 LOCK SCREW FOR 33-101-42 AND 33-101-43 ROLLER ASSEMBLIES 4 3. 33-108-02 TENSIONER ASSEMBLY 1 4. 123-1679 SCREW, 5/16-18 x 1-1/4, SOC. HD. CAP 1 5. 123-0855 LOCK WASHER, 5/16 SS 1 6. 123-2003 BELT, TIMING XL, 115 GROOVES, x 0.625, DOUBLE-SIDED 1 7. 123-0984 BELT, TIMING 40 DP, 94 GR., 0.188 1 8. 33-104-24 SUPPORT, TAB GUIDE 2 9. 123-0513 SCREW, 10-32 x 7/8 SOC. HD. CAP 3 10. 123-0531 SCREW, 10-32 x 3/4 FL. HD. PH 2 11. 33-104-29 TAB GUIDE WELDMENT, R/H 1 12. 33-104-30 TAB GUIDE WELDMENT, L/H 1 13. 123-0017 SCREW, 10-32 x 1/4 TRUSS HD. PH. SS 4 26

GROUP 5B DRIVE AND TRANSPORT NEW STYLE STRONGLY RECOMMENDED: REPLACE BEARINGS WHEN REPLACING ROLLER SHAFTS. 27

GROUP 5B DRIVE AND TRANSPORT NEW STYLE 1. 123-0017 SCREW, 10-32 x 1/4 TRUSS HD. PH. SS 4 2. 123-0513 SCREW, 10-32 x 7/8 SOC. HD. CAP 3 3. 123-0531 SCREW, 10-32 x 3/4 FL. HD. PH 2 4. 123-0751 SCREW, 6-32 x 3/8 FL. HD. PH. UNDERCUT 2 5. 123-0855 LOCK WASHER, 5/16 SS 1 6. 123-0984 BELT, TIMING 40 DP, 94 GR, 0.188 1 7. 123-1679 SCREW, 5/16 x 1-1/4, SOC. HD. CAP 1 8. 123-1708 BELT, TIMING 80xL037 1 9. 123-2003 BELT, TIMING AL, 115 GROOVES S 0.625, DOUBLE-SIDED 1 10. TRANSPORT SECTION (SEE GROUP 6) 1 10.1. 33-101-05 DRIVE ROLLER ASSEMBLY (SEE GROUP 6) 1 10.1.1. 33-101-29 PULLEY, 30 GROOVES 1 10.2. 33-101-30 ENCODER ASSEMBLY (INCLUDES 10.2.1, 10.2.2 & 10.2.3) 1 10.2.1. 123-2013 PULLEY, TIMING BELT, 33 GROOVES 1 10.2.2. 33-101-31 ENCODER BRACKET 1 10.2.3. 33-500-135 ENCODER 1 10.3. 33-101-55 BASE MOTOR ASSEMBLY 1 10.3.1. 33-101-47 MOTOR PULLEY SUBASSEMBLY, 12 XL 1 11. 33-104-24 SUPPORT, TAB GUIDE 2 12. 33-104-29 TAB GUIDE WELDMENT, R/H 1 13. 33-104-30 TAB GUIDE WELDMENT, L/H 1 14. 33-108-02 TENSIONER ASSEMBLY 1 15. 33-114-20 BOTTOM EXIT SHAFT ASSEMBLY 1 15.1. 123-0994 PULLEY, 40 DP 1 15.2. 33-101-29 PULLEY, 30 GROOVES 1 15.3. 33-101-15 BOTTOM EXIT SHAFT 1 15.4. 33-101-43 WHEEL ASSEMBLY, HARD (INCLUDES LOCK SCREW) 2 15.5. 33-101-42 WHEEL ASSEMBLY, SOFT (INCLUDES LOCK SCREW) 2 15.6. 90-101-04 PULLEY, 20 GROOVES, 1/5 PITCH 1 15.7. 123-0256 SCREW, 10-32 x 3/8 SOC. HD. CONE PT. 1 15.8 33-101-51 LOCK SCREW FOR 33-101-42 AND 33-101-43 ROLLER ASSEMBLIES 4 16. 33-114-30 INTERMEDIATE ROLLER SHAFT ASSY. 1 16.1. 99-100-98 BALL BEARING HOUSING ASSEMBLY 1 16.2. 33-114-31 SHAFT,INTERMEDIATE ROLLER 1 16.3. 65-303-01 MOTOR PULLEY ASSEMBLY, 14 GROOVES 1 16.4. 123-1861 SET SCREW, 10-24 x 1/4 HEX SOC. CUP PT. 1 16.5. 56-101-17 ROLLER ASSEMBLY, RUBBER FEED 4 16.6. 123-1956 SET SCREW, 8-32 x 5/16 SOC. HD. 4 28

GROUP 6 TRANSPORT SECTION STRONGLY RECOMMENDED: REPLACE BEARINGS WHEN REPLACING ROLLER SHAFTS. 29

GROUP 6 TRANSPORT SECTION 1. 123-0003 SCREW, 10-32 x 1/2 FL. HD. PH. UNDERCUT 2 2. 123-0004 SCREW, 10-32 x 5/8, SOC. HD. CAP, BLACK 4 3. 123-0063 WASHER, 0.62 OD x 0.281 ID x 1/16 4 4. 123-0064 LOCK WASHER, 1/4, SS 4 5. 123-0148 WASHER, 7/16 OD x 0.200 ID x 1/32 2 6. 123-0211 SCREW, 1/4-20 x 1-1/4 SOC. HD. CAP 4 7. 123-0513 SCREW, 10-32 x 7/8 SOC. HD. CAP 4 8. 123-0531 SCREW, 10-32 x 3/4 FL. HD. PH. 2 9. 123-0855 LOCK WASHER, 5/16 SS 2 10. 123-1677 LOCK WASHER, #10 SS 2 11. 123-1679 SCREW, 5/16-18 x 1-1/4, SOC. HD. CAP 2 12. HEAD RAISING MECHANISM (SEE GROUP 7) 1 13. 33-101-05 DRIVE ROLLER ASSEMBLY 1 13.1. 123-1997 BEARING 1 13.2. 123-1690 RETAINING CLIP, 5/8 x 0.588 x 0.039 2 14. 33-101-11 DRIVEN ROLLER ASSEMBLY 1 14.1 33-101-50 BEARING ASSEMBLY 2 14.2 123-0001 SET SCREW, 10-32 x 1/4 2 15. 33-101-25 ECCENTRIC 2 16. 33-101-30 ENCODER ASSEMBLY (SEE GROUPS 5A & 5B) 1 17. 33-101-41 BELT, REGISTRATION TABLE 6 18. 33-101-55 BASE MOTOR ASSEMBLY 1 19. 33-104-02 BELT SUPPORT ASSEMBLY 1 20. 33-104-12 CENTER PLATE SUPPORT ASSEMBLY 1 20.1. 97-115-02 WHEEL ASSEMBLY 2 20.2. 123-0008 SCREW, 10-32 x1/2 BTN. HD. PH 2 21. 33-101-29 PULLEY, 30 GROOVES 1 21.1. 123-0374 SET SCREW, 10-32 x 1/4 SOC. HD. SS, BLACK 2 22. 123-2033A SENSOR REFLECTOR 2 30

GROUP 7 HEAD RAISING MECHANISM 31

GROUP 7 HEAD RAISING MECHANISM 1. 123-0011 SCREW, 1/4-20 x 1, SOC. HD. CAP, BLACK 4 2. 123-0064 LOCK WASHER, 1/4 SS 4 3. 123-0374 SET SCREW, 10-32 x 1/2 HEXAGON SOCKET CUP PT. 2 4. MAIN FRAME ASSEMBLY (SEE GROUP 8) 1 5. 33-106-03 SHAFT, ECCENTRIC 2 6. 33-106-04 CAM, ECCENTRIC 4 7. 33-106-05 SCREW, ECCENTRIC CAM 4 8. 33-106-10 GEAR, WORM, 20 TOOTH 2 9. 33-106-07 HEIGHT ADJUSTMENT BRACKET 1 10. 33-106-28 HEIGHT ADJUSTMENT BRACKET 1 11. 123-2000 RUBBER BUMPERS (FEET) 4 12. 123-0051 NUT, 5/16-18 HEX 4 32

GROUP 8 MAIN FRAME 33

GROUP 8 MAIN FRAME 1. 123-0011 SCREW, 1/4-20 x 1. SOC. HD. CAP, BLACK 8 2. 123-0241 SCREW, 4-40 x 7/16 BIND HD. PH 1 3. 123-0531 SCREW, 10-32 x 3/4 FL. HD. PH 1 4. 123-0855 LOCK WASHER, 5/16 SS 2 5. 123-1679 SCREW, 5/16-18 x 1-1/4, SOC. HD. CAP 2 6. 33-100-04 FRONT SIDE FRAME ASSEMBLY (BEARINGS INCL.) 1 7. 33-100-09 REAR SIDE FRAME ASSEMBLY (BEARINGS INCL.) 1 8. 33-101-49 BEARING ASSEMBLY 3 9. 33-100-12 BRIDGE SUPPORT 1 10. 33-100-28 BEAM, BODY CROSS 1 11. 33-101-16 BELT GUIDE ASSEMBLY, FRONT 1 12. 33-101-17 BELT GUIDE ASSEMBLY, REAR 1 34

GROUP 9 BASE ELECTRICAL (115/120V) 35

GROUP 9 BASE ELECTRICAL (115/120V) 1. 95-100-32 SUPPORT, PC BOARD 10 2. 57-500-03 WIRE HARNESS ASSEMBLY - A/C INLET 1 3. 33-100-59 SLOTTED WIRING DUCT 1 4. 33-100-57 SLOTTED WIRING DUCT 2 5. 33-500-530 PC BOARD, I/O 1 6. 33-500-180 TERMINAL BLOCK (SEE GROUP 12) 1 7. 33-100-60 SLOTTED WIRING DUCT 1 8. 33-100-58 SLOTTED WIRING DUCT 1 9. 33-500-54 FRONT BOTTOM COVER WELDMENT 1 10. 33-200-40 FRONT COVER LAYOUT 1 11. 33-200-35 COVER, REAR BOTTOM 1 12. 33-100-24 GUIDE, WIRE HARNESS 1 13. 29-500-16 FILTER ASSEMBLY 2 14. 26-102-20 RELAY HOLDER ASSEMBLY 1 15. 123-2129 SCREW, 6-32 x 5/16, PH TRUSS HD. 2 16. 123-2053 CONNECTOR, 9-PIN 1 17. 123-2052 HINGE, LIFT-OFF L/H 1 18. 123-2051 HINGE, LIFT-OFF R/H 1 19. 123-2005 POWER SUPPLY 25 WATT 1 20. 33-500-200 CONTROLLER, SERVO MOTOR, S2000 (33-500-200 REPLACES 123-1998) 1 21. 33-565-10 CONTROL, SPEED 1 22. 123-1604 RELAY, KUEP-3A15 1 23. 123-1425 FUSE, 7A SLO-BL9O (3AG 0.313 SERIES) 1 24. 123-1359 RELAY, OMRON G7LL-1AS-TUB-J-CB-AC 100/120 1 25. 123-1313T 12V POWER SUPPLY MAP80-1012G 1 26. 123-1132 LABEL GROUND MACHINE 1 27. 123-0831 RELAY, AC SOLID STATE, 110-120V (110V VERSION) 2 28. 123-0612 SCREW, 6-32 x 1/4 PAN HD. PH. SS 14 29. 123-0461 SCREW, 6-32 x 3/16 SS H\PH ROUND HD. 31 30. 123-0434 SCREW, 10-32 x 5/16 SOC. CAP SS 18-8 2 31. 123-0355 HOLDER, FUSE 1 32. 123-0274 SCREW, 6-32 x 3/8 TRUSS HD. PH SS 4 33. 123-0237 STAR WASHER, #10 EXTERNAL 4 34. 123-0017 SCREW, 10-32 x 1/4 TRUSS HD. PH. SS 7 * 33-550-02 CONTROL PANEL DECAL 1 * 123-0635 115V POWER CORD 1 * NOT SHOWN 36

GROUP 9A BASE ELECTRICAL (220V) 37

GROUP 9A BASE ELECTRICAL (220V) 1. 95-100-32 SUPPORT, PC BOARD 10 2. 57-500-03 WIRE HARNESS ASSEMBLY - A/C INLET 1 3. 33-100-59 SLOTTED WIRING DUCT 1 4. 33-100-57 SLOTTED WIRING DUCT 2 5. 33-500-530 PC BOARD, I/O 1 6. 33-500-180 TERMINAL BLOCK (SEE GROUP 12) 1 7. 33-100-60 SLOTTED WIRING DUCT 1 8. 33-100-58 SLOTTED WIRING DUCT 1 9. 33-500-54 FRONT BOTTOM COVER WELDMENT 1 10. 33-200-40 FRONT COVER LAYOUT 1 11. 33-200-35 COVER, REAR BOTTOM 1 12. 33-100-24 GUIDE, WIRE HARNESS 1 13. 29-500-16 FILTER ASSEMBLY 2 14. 26-102-20 RELAY HOLDER ASSEMBLY 1 15. 123-2129 SCREW, 6-32 x 5/16, PH TRUSS HD. 2 16. 123-2053 CONNECTOR, 9-PIN 1 17. 123-2052 HINGE, LIFT-OFF L/H 1 18. 123-2051 HINGE, LIFT-OFF R/H 1 19. 123-2005 POWER SUPPLY 25 WATT 1 20. 33-500-200 CONTROLLER, SERVO MOTOR, S2000 (33-500-200 REPLACES 123-1998) 1 21. 33-565-10 CONTROL, SPEED 1 22. 123-1604 RELAY, KUEP-3A15 1 23. 123-1425 FUSE, 7A SLO-BL9O (3AG 0.313 SERIES) 1 24. 123-2292 RELAY, 220V 1 25. 123-1313T 12V POWER SUPPLY MAP80-1012G 1 26. 123-1132 LABEL GROUND MACHINE 1 27A 123-0831 RELAY, AC SOLID STATE, 110-120V 1 27B 123-2294 RELAY, AC SOLID STATE, 220V 1 28. 123-0612 SCREW, 6-32 x 1/4 PAN HD. PH. SS 14 29. 123-0461 SCREW, 6-32 x 3/16 SS H\PH ROUND HD. 31 30. 123-0434 SCREW, 10-32 x 5/16 SOC. CAP SS 18-8 2 31. 123-0355 HOLDER, FUSE 1 32. 123-0274 SCREW, 6-32 x 3/8 TRUSS HD. PH SS 4 33. 123-0237 STAR WASHER, #10 EXTERNAL 4 34. 123-0017 SCREW, 10-32 x 1/4 TRUSS HD. PH. SS 7 35. 123-1562 220V AC TRANSFORMER (SEE GROUP 9B) 1 * 33-550-02 CONTROL PANEL DECAL 1 * 123-0735 220V POWER CORD 1 * NOT SHOWN 38

GROUP 9B 220V TRANSFORMER & COMPONENTS EY PART NO. DESCRIPTION QTY. 33-900-30 220V CONVERSION KIT (Includes all parts listed below to convert a 115V ATS-9900 to 220V) 1. 123-1562 220V TRANSFORMER A41-130-230 1 2 33-100-62 TRANSFORMER MOUNTING BRACKET 1 3. 123-0524 SCREW, 1/4 x 1/2 SOC. HD. CAP 2 123-0063 WASHER, 5/8 OD x 9/32 ID x 1/16 2 123-0064 LOCK WASHER, 1/4 2 4. 123-0053 NUT, TRANSFORMER, NYLON INSERT 4 5. 33-505-05 TRANSFORMER WIRE HARNESS (1, C11) 1 6. 33-505-06 TRANSFORMER WIRE HARNESS (6, C5) 1 7. 33-505-08 TRANSFORMER FILTER WIRE HARNESS (8, 12, LINE 2) 1 8. 33-505-07 TRANSFORMER RELAY WIRE HARNESS (7, 11, OP2-1) 1 9. 20-500-107 TRANSFORMER JUMPER, WIRE HARNESS (2, 5) 1 123-2292 RELAY, 220V, 30 AMP (SEE GROUP 9A, KEY 24) 1 123-2293 RELAY, 220V (SEE GROUP 12, KEY 1) 1 123-2294 RELAY, AC SOLID STATE, 220V, 12 AMP (SEE GROUP 9A, KEY 27B) 1 123-0735 220V POWER CORD 1 39

GROUP 10 REAR COVER 40

GROUP 10 REAR COVER 1. 33-200-39 REAR TOP COVER 1 2. 33-500-30 CABLE SET, w/hip20 MOLEX CONNECTOR 1 3. 33-500-143 WIRE HARNESS, HEAD EXTENSION 1 4. 33-500-130 WIRE HARNESS, TAB SENSOR EXTENSION 1 5. 123-0274 SCREW, 6-32 x 3/8 TRUSS HD. PH. 12 6. 123-0192 NUT, 6-32 HEX 12 41

GROUP 11 CONTROL PANEL 42

GROUP 11 CONTROL PANEL 1. 33-200-42 FRONT TOP CLOSURE WELDMENT 1 2. 123-0612 SCREW, 6-32 x 1/4 PAN HD. PH. SS 6 3. 123-2027 LAMP, NEON 120V T-3 1/4 1 4. 123-2028 SWITCH, DUAL PUSH BUTTON 1 5. 123-2029 HOLDER, LAMP 1 6. 123-2006 SWITCH, LIGHTED PUSH BUTTON 2 7. 123-2017 LAMP, T-3 1/4, 14V 2 8. 123-1981 BLOCK, CONTACT 1 NO 3 9. 123-1637 SWITCH, EAO #704.02-1197 1 10. 123-2018 BLOCK, CONTACT 2NC 2 11. 123-1367 PUSHBUTTON, RED MUSHROOM (EMERGENCY) 1 12. 123-1440 CONTACT, 7049005 FOR IB 1 13. 33-500-505 PROCESSOR BOARD, 9900 1 14. 33-500-540 PC BOARD, KEYPAD DISPLAY 1 15. 33-500-05 POTENTIOMETER ASSEMBLY 1 16. 33-500-44 RESISTOR - POWER SWITCH, (FOR 110/120V VERSION) 1 33-505-09 RESISTOR - POWER SWITCH, (FOR 220V VERSION) 1 43

GROUP 12 TERMINAL BLOCK 44

GROUP 12 TERMINAL BLOCK 1. 123-1356 RELAY, OMRON LY2-AC110120, (FOR 110V/120V VERSION) 1 123-2293 RELAY, (FOR 220V VERSION) 1 2. 123-1357 SOCKET, RELAY OMRON 3 3. 123-1423 FUSE, 3Z SLO-BLO 1 4. 123-1424 FUSE, 5A SLO-BLO 1 5. 123-1445 BLOCK, SINGLE LEVEL TERMINAL 4 6. 123-1446 BLOCK, TERMINAL GROUND 1 7. 123-1448 TAGS, MARKING GND 1 8. 123-1449 TAGS, MARKING 1-50 1 9. 123-1451 PLATE, END WAP 2.5 10 1 10. 123-1502 BLOCK, TERMINAL 2/FUSE FOR 33MM DIN-RAIL 3 11. 123-1585 FUSE, 2A SLO-BLO 1 12. 123-1661 BRACKET, END WEW 1 13. 123-1662 BRANCH, WDU 3 14. 123-1663 BRANCH, WDU 3 15. 123-1665 BLOCK, DOUBLE LEVEL TERMINAL 2 16. 123-1666 PLATE, END WAP 1 17. 123-1759 JUMPER, WZQ 1 18. 123-1798 JUMPER, QL3 1 19. 123-1799 JUMPER, SCREW 3 20. 123-1970 RELAY, OMRON LY2-DC12 2 21. 123-2034 SOCKET, 11 PIN DIN RAIL MOUNT 1 22. 123-2035 RELAY, 4PDT 12V DC CO9L 1 23. 123-2076 JUMPER, WQV 1 45

GROUP 13 FEEDER GUIDE KIT KEY PART NO. DESCRIPTION QTY 33-104-40 FEEDER GUIDE KIT (INCLUDES ALL COMPONENTS LISTED BELOW) 1. 33-104-42 FEEDER GUIDE (ATTACHES TO TABBER) 1 2. 123-0620 RUBBER FOOT 2 3. 123-0053 NYLON INSERT STOP NUT, 10-32 2 4. 33-104-41 FEEDER BASE GUIDE (ATTACHES TO FEEDER BASE STAND) 5. 33-104-43 TEFLON TAPE 1 1 1 46

PART NO. GROUP KEY 123-0001 6 14.2 123-0003 6 1 123-0004 1C 1 123-0004 1D 1 123-0004 6 2 123-0008 3A 10.6 123-0008 3B 10.6 123-0008 3B 13.4.2 123-0008 6 20.2 123-0011 1 1 123-0011 1B 19 123-0011 4A 1 123-0011 4B 1 123-0011 7 1 123-0011 8 1 123-0017 2A 1 123-0017 2B 1 123-0017 2C 1.4 123-0017 3A 1 123-0017 3B 1 123-0017 3B 13.3 123-0017 5A 13 123-0017 5B 1 123-0017 9 34 123-0017 9A 34 123-0021 4C 2.3 123-0024 3A 17.2 123-0024 3B 17.2 123-0035 2C 2.8 123-0035 2C 3.8 123-0035 2C 4.6 123-0051 7 12 123-0053 2C 2.3 123-0053 2C 3.3 123-0053 4C 1.5 123-0053 9B 4 123-0053 13 3 123-0063 6 3 123-0063 9B 3 123-0064 1 2 123-0064 4A 2 123-0064 4B 2 123-0064 6 4 123-0064 7 2 123-0064 9B 3 123-0080 4C 1.9 123-0127 2C 4.3 123-0148 6 5 123-0169 2C 2.7 123-0169 2C 3.7 123-0169 2C 4.5 123-0182 1 3 123-0182 4A 3 INDEX 47 PART NO. GROUP KEY 123-0182 4B 3 123-0191 1C 2 123-0191 1D 2 123-0192 10 6 123-0211 6 6 123-0237 2A 2 123-0237 2B 2 123-0237 9 33 123-0237 9A 33 123-0241 8 2 123-0256 5B 15.7 123-0267 1C 3 123-0267 1D 3 123-0274 9 32 123-0274 9A 32 123-0274 10 5 123-0278 1 4 123-0324 1A 18 123-0355 9 31 123-0355 9A 31 123-0374 3A 2 123-0374 3B 2 123-0374 6 21.1 123-0374 7 3 123-0381 3A 13.2 123-0381 3B 13.2 123-0434 9 30 123-0434 9 30 123-0461 9A 29 123-0461 9A 29 123-0513 5A 9 123-0513 5B 2 123-0513 6 7 123-0524 1 5 123-0524 1C 4 123-0524 1D 4 123-0524 9B 3 123-0531 5A 10 123-0531 5B 3 123-0531 6 8 123-0531 8 3 123-0573 3A 16 123-0573 3B 16 123-0612 1C 5 123-0612 9 28 123-0612 9A 28 123-0612 11 2 123-0620 13 2 123-0635 9 -- 123-0735 9A -- 123-0735 9B -- 123-0751 5B 4 123-0757 1B 20.1

PART NO. GROUP KEY 123-0831 9 27 123-0831 9A 27A 123-0855 4A 4 123-0855 4B 4 123-0855 5A 5 123-0855 5B 5 123-0855 6 9 123-0855 8 4 123-0975 1C 6 123-0975 1D 5 123-0976 4C 1.7 123-0978 3A 14.4.3 123-0978 3B 14.4.3 123-0978 4A 21.3 123-0978 4B 21.3 123-0984 5A 7 123-0984 5B 6 123-0988 1B 22.2 123-0988 3A 14.4.4 123-0988 3B 14.4.4 123-0988 4A 21.4 123-0988 4B 21.4 123-0994 5A 2.1 123-0994 5B 15.1 123-1085 1B 21 123-1132 9 26 123-1132 9A 26 123-1135 2C 2.10 123-1135 2C 3.9 123-1135 2C 4.7 123-1161 1A 17 123-1178 2A 3 123-1178 2B 3 123-1204 1A 16 123-1206 2C 2.5 123-1206 2C 3.5 123-1206 4C 1.3 123-1210 1A 15 123-1210 2C 1.3 123-1210 2C 2.4 123-1210 2C 3.4 123-1210 4C 1.4 123-1313T 9 25 123-1313T 9A 25 123-1356 12 1 123-1357 12 2 123-1359 9 24 123-1367 11 11 123-1382 4A 5 123-1382 4B 5 123-1423 12 3 123-1424 12 4 123-1425 9 23 INDEX 48 PART NO. GROUP KEY 123-1425 9A 23 123-1440 11 12 123-1442 2A 4 123-1442 2B 4 123-1445 12 5 123-1446 12 6 123-1448 12 7 123-1449 12 8 123-1451 12 9 123-1502 12 10 123-1503 2A 5 123-1503 2B 5 123-1503 2C 1.2 123-1562 9A 35 123-1562 9B 1 123-1585 12 11 123-1604 9 22 123-1604 9A 22 123-1630 4A 6 123-1630 4B 6 123-1637 11 9 123-1650 1A 14 123-1661 12 12 123-1662 12 13 123-1663 12 14 123-1665 12 15 123-1666 12 16 123-1677 1C 7 123-1677 1D 6 123-1677 6 10 123-1679 5A 4 123-1679 5B 7 123-1679 6 11 123-1679 8 5 123-1690 6 13.2 123-1708 5B 8 123-1759 12 17 123-1790 2A 6 123-1790 2B 6 123-1798 12 18 123-1799 12 19 123-1861 3A 3 123-1861 3B 3 123-1861 5B 16.4 123-1956 5B 16.6 123-1970 12 20 123-1981 11 8 123-1997 6 13.1 123-2000 7 11 123-2003 5A 6 123-2003 5B 9 123-2004 3A 4 123-2004 3B 4

PART NO. GROUP KEY 123-2005 9 19 123-2005 9A 19 123-2006 11 6 123-2013 5A 1.2.1 123-2013 5B 10.2.1 123-2017 11 7 123-2018 11 10 123-2027 11 3 123-2028 11 4 123-2029 11 5 123-2030 1B 22.3 123-2030 3A 14.4.5 123-2030 3B 14.4.5 123-2033A 4A 28 123-2033A 4B 28 123-2033A 6 22 123-2034 12 21 123-2035 12 22 123-2040 3A 8A 123-2040 3B 8A 123-2051 9 18 123-2051 9A 18 123-2052 9 17 123-2052 9A 17 123-2053 9 16 123-2053 9A 16 123-2062 1A 13 123-2076 12 23 123-2129 9 15 123-2129 9A 15 123-2292 9A 24 123-2292 9B -- 123-2293 9B -- 123-2293 12 1 123-2294 9A 27B 123-2294 9B -- 20-500-107 9B 9 21-144-00 4C 1.8 25-116-34 2C 2.2 25-116-34 2C 3.2 25-116-34 4C 1.2 25-133-21 2C 2.1 25-133-21 2C 3.1 25-133-21 4C 1.1 26-102-20 9 14 26-102-20 9A 14 28-104-13 3A 10.3 28-104-13 3B 10.3 28-104-13 4A 21.5 28-104-13 4B 21.5 29-500-16 9 13 29-500-16 9A 13 32-111-17 4C 1.10 INDEX 49 PART NO. GROUP KEY 33-100-04 8 6 33-100-09 8 7 33-100-12 8 9 33-100-15 2A 7 33-100-15 2B 7 33-100-24 9 12 33-100-24 9A 12 33-100-28 8 10 33-100-56 3A 5 33-100-56 3B 5 33-100-57 9 4 33-100-57 9A 4 33-100-58 9 8 33-100-58 9A 8 33-100-59 9 3 33-100-59 9A 3 33-100-60 9 7 33-100-60 9A 7 33-100-62 9B 2 33-101-05 5A 1.1 33-101-05 5B 10.1 33-101-05 6 13 33-101-11 6 14 33-101-14 5A 2 33-101-15 5A 2.3 33-101-15 5B 15.3 33-101-16 8 11 33-101-17 8 12 33-101-25 6 15 33-101-28 3A 6 33-101-28 3B 6 33-101-29 5A 1.1.1 33-101-29 5A 2.2 33-101-29 5B 10.1.1 33-101-29 5B 15.2 33-101-29 6 21 33-101-30 5A 1.2 33-101-30 5B 10.2 33-101-30 6 16 33-101-31 5A 1.2.2 33-101-31 5B 10.2.2 33-101-41 6 17 33-101-42 5A 2.5 33-101-42 5B 15.5 33-101-43 3A 7 33-101-43 3B 7 33-101-43 5A 2.4 33-101-43 5B 15.4 33-101-46 3A 8 33-101-46 3B 8 33-101-47 5A 1.3.1 33-101-47 5B 10.3.1 33-101-49 8 8

PART NO. GROUP KEY 33-101-50 6 14.1 33-101-51 3A 7A 33-101-51 3B 7A 33-101-51 5A 2.6 33-101-51 5B 15.8 33-101-55 5A 1.3 33-101-55 5B 10.3 33-101-55 6 18 33-102-03 3A 14.2 33-102-03 3B 14.2 33-102-03 4A 8 33-102-03 4B 8 33-102-05 3A 14.3 33-102-05 3B 14.3 33-102-05 4A 9 33-102-05 4B 9 33-102-07 4A 10 33-102-07 4B 10 33-102-08 4A 11 33-102-08 4B 11 33-102-10 4A 12 33-102-10 4B 12 33-104-02 6 19 33-104-05 2A 8 33-104-05 2B 8 33-104-10 2A 9 33-104-10A 2B 9 33-104-12 6 20 33-104-24 5A 8 33-104-24 5B 11 33-104-29 5A 11 33-104-29 5B 12 33-104-30 5A 12 33-104-30 5B 13 33-104-40 13 -- 33-104-41 13 4 33-104-42 13 1 33-104-43 13 5 33-105-02 4A 13 33-105-02 4B 13 33-105-04 4A 14 33-105-04 4B 14 33-105-06 4A 15 33-105-06 4B 15 33-105-09 4A 16 33-105-09 4B 16 33-105-14 4A 17 33-105-14 4B 17 33-105-17 4A 18 33-105-17 4B 18 33-105-18 4A 19 33-105-18 4B 19 33-105-19 4A 20 INDEX 50 PART NO. GROUP KEY 33-105-19 4B 20 33-106-03 7 5 33-106-04 7 6 33-106-05 7 7 33-106-07 7 9 33-106-10 7 8 33-106-28 7 10 33-108-02 3A 14.1.1 33-108-02 3B 14.1 33-108-02 5A 3 33-108-02 5B 14 33-108-12 3A 9 33-108-12 3B 9 33-109-02 2C 1 33-109-05 2C 1.5 33-109-06 2C 1.6 33-109-12 2C 1.1 33-109-18 4A 26 33-109-18 4B 26 33-109-19 4A 27 33-109-19 4B 27 33-109-31 2C 2 33-109-32 2C 3 33-109-33 2C 3.6 33-109-35 2C 2.6 33-109-39 2C 2.9 33-109-39 2C 3.10 33-109-39 2C 4.8 33-109-44 2C 4 33-109-46 2C 4.2 33-109-48 2C 4.4 33-110-02 3A 10 33-110-02 3B 10 33-110-03 3A 10.2 33-110-03 3B 10.2 33-110-05 3A 10.1 33-110-05 3B 10.2 33-110-08 3A 13.1 33-110-08 3B 13.1 33-110-10 3A 10.4 33-110-10 3B 10.4 33-110-11 3A 13 33-110-13 3A 11 33-110-17 3A 14.4.2 33-110-17 3B 14.4.2 33-110-17 4A 21.2 33-110-17 4B 21.2 33-110-31 3A 14.4.1 33-110-31 3B 14.4.1 33-110-31 4A 21.1 33-110-31 4B 21.1 33-110-33 3A 14.4 33-110-33 3B 14.4

PART NO. GROUP KEY 33-110-33 4A 21 33-110-33 4B 21 33-110-35 3A 14.5 33-110-35 3B 14.5 33-110-35 4A 22 33-110-35 4B 22 33-110-63 3A 17.1 33-110-63 3B 17.1 33-110-67 3A 17.3 33-110-67 3B 17.3 33-111-03 1B 18B 33-111-03 1D -- 33-111-05 1C 8 33-111-05 1D 7 33-111-07 1D 8 33-111-08 1C 9 33-111-08 1D 9 33-111-10 1D 10 33-111-11 1C 10 33-111-11 1D 11 33-111-12 1C 11 33-111-12 1D 12 33-111-13 1C 12 33-111-13 1D 13 33-112-01 1B 18 33-112-01 1C 13 33-112-01 1D 14 33-112-15 1C 14 33-112-15 1D 15 33-113-03 1B 18A 33-113-03 1C -- 33-113-07 1C 15 33-113-10 1C 16 33-113-17 1A -- 33-113-31 1A -- 33-114-06 3B 13 33-114-10 3B 13.4 33-114-20 5B 15 33-114-23 3B 11 33-114-30 5B 16 33-114-31 5B 16.2 33-115-40 4C 1 33-115-41 4C 1.6 33-115-44 4C 2 33-115-45 4C 2.2 33-115-46 4C 2.4 33-115-48 4C 2.5 33-119-06 4A 23 33-119-06 4B 23 33-120-07 1B 17 33-120-15 1B 22 33-120-16 1B 22.1 33-121-08 1B 15 INDEX 51 PART NO. GROUP KEY 33-121-12 1B 14 33-121-14 1B 13 33-121-15 1B 12 33-122-06 1B 11 33-122-11 1B 10 33-122-19 1B 9 33-122-22 1B 8 33-122-27 1B 7 33-122-35 1B 6 33-125-06 1A 11 33-125-07 1A 10 33-125-08 1A 9 33-125-11 1A 8 33-125-12 1A 7 33-125-13 1A 6 33-125-18 1A 5 33-125-19 1A 4 33-125-24 1A 2 33-126-13 1B 5 33-126-15 1B 4 33-126-17 1B 20 33-200-20 2A 11 33-200-20 2B 11 33-200-30 2A 12 33-200-30 2B 12 33-200-31 2A 13 33-200-31 2B 13 33-200-32 2A 14 33-200-32 2B 14 33-200-33 2A 15 33-200-33 2B 15 33-200-35 9 11 33-200-35 9A 11 33-200-36 4A 24 33-200-36 4B 24 33-200-37 3A 14.6 33-200-37 3B 14.6 33-200-37 4A 25 33-200-37 4B 25 33-200-38 2A 16 33-200-38 2B 16 33-200-39 10 1 33-200-40 9 10 33-200-40 9A 10 33-200-42 11 1 33-206-19 2A 17 33-206-19 2B 17 33-220-02 1 7 33-220-20 1B 16 33-225-02 1 8 33-225-04 1A 12 33-225-23 1A 3 33-500-05 11 15

PART NO. GROUP KEY 33-500-30 10 2 33-500-44 11 16 33-500-54 9 9 33-500-54 9A 9 33-500-77 1B 1 33-500-78 1A 1 33-500-130 10 4 33-500-134 1B 3 33-500-135 5A 1.2.3 33-500-135 5B 10.2.3 33-500-143 10 3 33-500-144 1B 2 33-500-180 9 6 33-500-180 9A 6 33-500-200 9 20 33-500-200 9A 20 33-500-505 11 13 33-500-530 9 5 33-500-530 9A 5 33-500-540 11 14 33-505-05 9B 5 33-505-06 9B 6 33-505-07 9B 8 33-505-08 9B 7 33-505-09 11 16 33-550-02 9 * 33-550-02 9A * 33-565-10 9 21 33-565-10 9A 21 33-900-10 3A 17 33-900-10 3B 17 33-900-20 3A 12 33-900-20 3B 12 33-900-30 9B -- 56-101-17 5B 16.5 57-500-03 9 2 57-500-03 9A 2 65-303-01 3A 15 65-303-01 3B 15 65-303-01 5B 16.3 84-114-05 2C 4.1 84-114-05 4C 2.1 90-101-04 5B 15.6 95-100-32 9 1 95-100-32 9A 1 97-115-02 2C 1.7 97-115-02 3A 10.5 97-115-02 3B 10.5 97-115-02 3B 13.4.1 97-115-02 6 20.1 99-100-98 5B 16.1 SM-9900 4C INDEX 52

Copyright 2018 Astro Machine Corp. 03/27/2018 Part Number: 100-ATS9900 Rev. T