SERVICE IPL, LT151, 00-10, 544 33 55-08 9604100105 LT151 Spare parts Ersatzteile Pièces détachées Reserve onderdelen Repuestos Reservdelar 544 33 55-08
ILLUSTRATED PARTS LIST MODEL NO. 9604100105 CUSTOMER CATALOG NO. LT151 PRODUCT NO. 960 41 00-1 4 53 41 54-81 Rev. 11 05.8.09 SR
DECALS 8 4 1 9 5 11 5 6 10 3 13 1 1 53 40 03-89 Decal, Operators 53 40 8-3 Decal, Hood/Fender 3 53 19 68-41 Decal, Warning Eng. Symbols 4 53 40 85-96 Decal, Hood Panel 5 53 15 9-36 Decal, Chassis Hot Muffler 6 53 18 04-3 Decal, Fender 100 DB/CE 53 18 1-66 Decal, Cutfinger CE 8 53 41 30-01 Decal, Rpl. Kohl 15 9 53 14 50-05 Decal, Battery Dan./Poi. 10 53 14 08-3 Decal, Saddle Brake Parking 11 53 19 63-5 Decal, Warning 1 53 19 43-0 Decal, Mower V-Belt Schematic 13 53 15 9-3 Decal, Brake/Clutch Symbol - - 53 41 08-05 Pad, Footrest, LH - - 53 41 10-56 Pad, Footrest, RH - - 53 16 5-98 Decal, Drawbar Load Limit - - 53 40 8-08 Manual Oper. Euro - - 53 40 8-09 Manual Oper. Scand - - 53 40 8-10 Manual Oper. E-Bloc - - 53 40 8-11 Manual Oper. Baltic WHEELS AND TIRES 1 6 11 3 4 10 5 9 8 1 53 05 91-9 Cap Valve Tire 53 06 51-39 Stem Valve 3 53 13 83-36 Rim Asm. 6" Front 4 53 05 99-04 Tube Front (Service Item Only) 5 53 10 6- Tire F T 15 x 6 0-6 6 53 1 49-5 Fitting Grease (Front Wheel Only) 53 1 49-59 Bearing Flange (Front Wheel Only) 8 53 1 50-39 Cap Axle Blk. 1 50 x 1 00 9 53 10 6-68 Tire R 18 x 9.5-8 Turf Saver - - 53 4 05-31 Tire R 18 x 9.5-8 Turf Saver LT 10 53 1 49-6 Tube Rear (Service Item Only) 11 53 13 83-3 Rim Asm. 8" Rear - - 53 14 43-34 Sealant, Tire (10 oz. Tube) wheel_art_1-tex NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm
SCHEMATIC 38 SCH0 BATTERY RED RED RED A AMMETER (OPTIONAL) FUSE SOLENOID STARTER M B S M G A1 L A BLUE WHITE CLUTCH / BRAKE (PEDAL UP) ATTACHMENT CLUTCH (CLUTCH OFF) BLACK BLACK BLACK SEAT SWITCH (NOT OCCUPIED) BLACK GRAY GRAY BLACK REVERSE SWITCH NOT IN REVERSE SHORTING CONNECTOR BLACK BLACK/WHITE IGNITION UNIT SPARK PLUGS GAP ( PLUGS ON TWIN CYL. ENGINES) BLUE FUEL LINE HOUR METER (OPTIONAL) BLACK BLUE RED FUEL SHUT-OFF SOLENOID CHARGING SYSTEM OUTPUT 9-16 AMP DC @ 3600 RPM REGULATOR 8 VOLTS AC @ 3600 RPM (REGULATOR DISCONNECTED) STATOR ORANGE LIGHT SW BROWN BLACK HEADLIGHTS IGNITION SWITCH POSITION CIRCUIT MAKE OFF M+G+A1 RUN/OVERRIDE B+A1 RUN B+A1 L+A START B+S+A1 WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING. 3 REMOVABLE CONNECTIONS NON-REMOVABLE CONNECTIONS
ELECTRICAL 3 T0S With 1V Outlet Option 103 9 1 30 33 8 59 With Service Minder Option 34 43 4 46 6 40 41 5 16 90 1 9 94 8 55 9 93 4
ELECTRICAL 3 1 53 16 34-65 Battery 84 6 04-1 Bolt Hex Head 1/4-0 x 3/4 8 53 19 3-8 Box Battery 16 53 1 61-38 Switch Interlock Push-In 1 53 40 0-5 Harness Socket Light w/415j 53 00 41-5 Bulb Light 5 53 41 8-94 Cable Starter 6 53 1 51-58 Fuse 83 51 04-00 Nut Keps Hex 1/4-0 unc 8 53 19 88-85 Cable, Ground 9 53 40 15-45 Switch, Seat 30 53 19 33-50 Switch, Ign. 33 53 41 19-35 Key/Chain 34 53 11 0-1 Switch Light/Reset 40 53 40 10-98 Harness Ign. Dash 41 81 04-08 Screw Thd. Cut 1/4-0 x 1/ 4 53 13 15-63 Cover, Terminal 43 53 19 5-0 Solenoid 55 81 06 05-1 Screw Thdrol. 5/16-18 x 3/4 TYTT 1 53 40 04-49 Harness Chassis 9 53 1 5-4 Socket Asm. Bulb Twistlock 8 53 19 8-0 Switch Interlock Clutch Cable 90 53 40 0-5 Cover Terminal 9 53 19 66-15 Harness Pigtail Reverse Switch 93 53 19 5-40 Screw Plastite 10-14 x.0 94 53 19 18-34 Module Reverse ROS NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 5
CHASSIS AND ENCLOSURES 39 15 9 3 18 38 03 06 04 6 191 5 16 5 14 130 14 13 16 34 1 16 15 05 0 86 83 84 195 16 85 36 194 36 199 18 16 130 15 150 130 151 159 194 35 36 180 8 3 8 194 1 8 16 8 189 58 8 183 68 159 189 159 chassis-tex_tex LT HUSQ_13_r 6
CHASSIS AND ENCLOSURES 39 53 41-8 Drawbar 3 53 40 50-1 Logo 5 53 40 5-9 Dash 6 53 40 48-83 Clip Tinnerman 14 53 4 59-83 Hood 15 53 41 10-9 Lens LH 18 53 4 69-63 Grille 5 53 41 10-8 Lens RH 36 81 06 05-1 Screw 5/16-18 x 3/4 3 53 41 63-0 Fender 58 53 41-80 Drawbar Upper 68 81 49 05-08 Screw Thdrol. 5/16-18 x 1/ 130 53 41 63-58 Screw #10 x 0.50 13 53 40 5-90 Bumper Dash 150 53 40 5-3 Air Duct 151 53 40 8-0 Bracket Pivot 15 53 19 43-9 Shield Browning 159 81 00 06-1 Screw 3/8-16 x 3/4 16 53 14 4-3 Screw Hex Wsh. Hi-Lo 1/4 x 1/ unc 15 53 19 94- Crossmember 16 53 40 0-6 Screw 10-4 x 5/8 1 53 19 5-8 Bushing Steering 180 53 19 4-60 Chassis 18 53 40 1-6 Dash Lower 183 84 8 05-0 Bolt 5/16-18 unc x 1-1/4 189 81 00 05-1 Screw 5/16-18 x 3/4 191 53 41 65-00 Insert Reflective RH 194 83 90 05-00 Nut Lock Hex Flange 5/16-18 195 53 41 11-15 Plug Dash 199 53 41 34-85 Plate Deck Lift 0 53 41 10-4 Vent Side Hood RH 03 53 41 10-5 Vent Side Hood LH 04 53 41 11-16 Vent Top Hood 05 53 41 10-6 Skirt Side RH 06 53 41 10- Skirt Side LH 14 53 19 91-45 Clip Retainer 1 53 40 91-6 Rod Pivot Hood 8 53 19 51-61 Stud Fastener 34 53 40 4-4 Bumper Hood 35 53 40 61-9 Spacer Fender 36 83 93 05 00 Nut Center Lock 5/16-18 unc 38 53 41 11-19 Trim 8 53 41 41-10 Clip Retainer 83 53 41 34-9 Console Deck Lift 84 53 41 34-89 Console Shift 85 53 41 63-15 Console Insrt. RH 86 53 41 63-1 Console Insrt. LH 8 81 60 04-06 Screw Hex Washead. 1/4-0 x 3/8 9 53 40 66-65 Insert Reflective NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm
DRIVE 40 185 56 184 1 35 15 1 160 4 64 160 16 03 188 159 15 1 161 15 190 49 186 189 18 50 51 61 155 139 0 140 141 134 165 166 19 14 5 51 116 158 15 19 193 15 18 16 33 195 15 3 166 3 9 1 6 15 159 3 1 3 05 drive-tex_d6800_fender_41_r1 33 8
DRIVE 40 1 - - - - - - Transaxle, Dana D6800-1 53 1 35-83 Key Square 15 819 13 13-16 Washer 13/3 x 13/16 x 16 Ga. 1 53 19-9 Spring, Brake 53 19 6-60 Rod Shift 3 53 1 1-4 Knob Duckhead 1/-13 6 53 19 4-55 Spring Brake Return 9 53 19-6 Rod, Brake 33 81 00 00-01 Ring E 35 53 40 10-31 Rod, Brake, Park 3 53 1 1-49 Washer 5/3 x 1-1/4 x 16 Ga. 4 53 1 48- Cover, Foot Pedal 49 8 11 06-14 Bolt 50 53 19 43- Pulley Idler Flat 51 83 90 06-00 Lock Nut 3/8-16 5 53 19 43-6 Idler V-Groove 910" Offset 56 53 41 1-45 V-Belt, Drive 61 53 1 36-66 Pulley Transaxle 64 53 19 6-00 Shaft Asm. Pedal Brake Control 3 84 49 05-44 Bolt Hex Flghd. 5/16-18 Gr. 5 116 83 90 05-00 Nut Lock Hex Flange 5/16-18 15 81 00 05-1 Screw 5/16-18 x 3/4 134 53 40 4-30 Asm. Shift 139 84 55 04-1 Bolt 1/4-8 unf Gr. 8 w/patch 140 810 04 04-00 Washer Lock Hvy. Helical 1/4 141 819 09 1-10 Washer 9/3 x 3/4 x 10 Ga. 155 81 00 00-8 Ring Retainer 15 53 10 5-01 Washer Plate Shift 158 53 19 43-5 Belt Keeper 159 86 0 04-1 Pin Cotter 1/8 x 3/4 160 53 16 94-84 Retainer Clip 161 53 10 5-09 Spring, Return, Clutch 165 53 19 6-1 Bushing Shaft Brake Hand Control 166 53 4 83-05 Nut Push.65 16 53 40 5-5 Latch Brake Parking 1 53 19 6-5 Strap Torque LH 14 53 19-89 Nut Push 15 53 19 89-81 Shaft Asm. Shift 16 53 19 6-14 Arm Clevis Rod Shift 18 53 19 4-56 Spring Shift 184 53 40 9-4 Knob 185 8 11 06- Bolt 186 53 19 43-1 Spacer Retainer 18 819 13 3-10 Washer 188 53 19 43-3 Link Clutch Ground Drive 189 53 19 43-1 Bellcrank Ground Drive 190 53 19 43-18 Keeper Bellcrank Ground Drive 19 53 15 03-60 Nut Lock Center 1/4-8 Fnthd. 193 81 06 05-1 Screw 5/16-18 x 3/4 195 53 19 3-3 Bracket Brake Rod 0 53 19 95-89 Link Transaxle 03 819 11 11-16 Washer 11/3 x 11/16 x 16 Ga. 05 53 1 1-48 Washer 5/3 x 1-5/8 16 Ga. 1 53 40 31-8 Retainer Spring Clip Handle 3 84 8 0-16 Bolt Fin. Hex /16-14 x 1 Gr. 5 33 53 40 5-96 Washer Serrated NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 9
ENGINE 4 1 1 0 81 45 83 18 15 44 46 3 9 69 3 8 9 4 1 95 94 9 90 SPARK ARRESTER KIT engine-tex_kohl_18 43 10
ENGINE 4 1 - - - - - - Engine Kohler Model No. SV40-011 53 18 86-55 Muffler 9 53 19 43-19 Keeper Belt Engine 1 53 40 19-85 Pulley Engine 15 53 40 5-45 Tank Fuel 1.5 18 53 4 51-6 Cap Fuel 0 53 18 38-9 Control Throttle 1 53 41 63-58 Screw #10 x 0.50 8 53 13 0-40 Fuel Line 9 53 13 1-80 Spark Arrester Kit 3 53 1 34-8 Clamp Hose 41 810 04 0-00 Bolt 5/16-18 unc x 3/4 w/sems. 4 810 04 0-00 Washer Lock /16 43 53 1 39-3 Bolt Hex /16-0 x 4 Gr. 5 44 81 6 04-1 Screw 1/4-0 x 3/4 45 83 51 04-00 Nut Keps Hex 1/4-0 unc 46 819 09 14-16 Washer 9/3 x /8 x 16 Ga. 69 53 18 59-09 Gasket 81 53 14 84-56 Tube Drain Oil Easy 83 53 1 18- Bolt 5/16-18 unc x 3/4 w/sems. 90 81 00 06-16 Screw 3/8-16 x 1 9 81 1 06-16 Screw 3/8-16 x 1 94 53 18 86-54 Tube Exhaust 95 53 19 3-34 Screw Socket HD 5/16-18 x.5 NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 11
STEERING ASSEMBLY 41 6 33 45 1 0 1 1 16 63 5 64 8 19 13 8 58 60 5 63 59 4 35 61 15 9 8 6 4 14 55 6 6 8 8 6 65 9 4 5 55 54 66 54 69 68 50 0 50 65 6 14 15 13 13 8 53 steering-tex_husqsr_8 1
STEERING ASSEMBLY 41 1 53 41 64-80 Wheel, Steering 53 41 81-68 Axle Asm., Front 4 53 40 30-8 Spindle Asm., LH 5 53 40 30-88 Spindle Asm., RH 6 53 1 49-31 Bearing, Race Thrust Hardened 53 1 1-48 Washer 5/3 x 1-5/8 x 16 Ga. 8 81 00 00-9 Ring, Clip #T5304-5 9 53 1 1-3 Cap, Spindle 13 53 1 1-49 Washer 5/3 x 1-1/4 x 16 Ga. 14 810 04 06-00 Washer, Lock Hvy. Hlcl. Spr. 3/8 15 83 54 06-00 Nut, Crown Lock 3/8-4 unf 16 53 19 60-4 Shaft Steering 19 53 19 4-9 Plate Steering 0 53 41 11-39 Boot, Steering 1 53 18 6-3 Adapter, Wheel Steering 53 19 48-45 Bushing, Strg. Blk. 6 53 41 59-8 Insert, Wheel Steering 8 81 00 06-1 Screw 3/8-16 x 3/4 33 810 04 05-00 Washer Lock 5/16 35 53 19 4-3 Gear, Sector Plate 45 819 11 38-1 Washer 11/3 x 3/8 x 1 Ga. 50 83 90 06-00 Nut Lock 3/8-16 unc 53 53 18 89-6 Washer Hardened.93 x 1.63 x.060 54 84 6 06-36 Bolt Hex 3/8-16 unc x -1/4 55 53 41 4-36 Spacer Brace Axle 5 53 40 4-65 Bracket Upstop 58 53 19 4-4 Bolt Shoulder Sector Pivot CFM 59 53 19 4-48 Washer Thrust Sector Steering 60 83 9 10-00 Nut Flange Lock 5/8-11 61 53 19 4-40 Draglink, LH 6 53 19 4-41 Draglink, RH 63 81 00 05-1 Screw 5/16-18 x 3/4 64 53 19 98-49 Retainer Clip Spring Steering 65 53 19 4-34 Brace Axle Front 66 81 0 0-48 Bolt Hex Fghd. /16-14 x 3 Serr. 6 53 19 4-3 Bushing PM Front Axle 68 83 90 0-00 Nut Lock Flange /16-14 Gr. 5 69 53 19 91-6 Washer 1.5 x.505 x.118 0 53 19 61-9 Bracket Deck Susp. Front 1 53 19 60-5 Shaft Extension Steering 84 8 05- Bolt 5/16-18 unc x 4.5. Gr. 5 4 53 1 49-3 Bearing Col. STRG 8 53 05 0-9 Washer Thrust 515.50 x.033 NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 13
MOWER DECK 44 0 6 15 3 56 30 5 43 4 60 64 40 40 145 59 5 56 55 46 63 14 34 68 33 195 1 13 195 38 09 145 3 31 144 38 30 30 1 1 189 188 34 69 1 1 3 4 5 19 6 189 188 15 1 9 6 6 19 14 11 13 69 199 8 69 38-_Tex-LT_3_r3 14
MOWER DECK 44 1 53 19 4-51 Mower Housing 6 53 19 51-86 Arm Suspension 53 41 63-58 Screw #10 x 0.50 8 53 19 30-03 Bolt/Washer Asm. /16-0 unf 11 53 19 39-5 Blade 38" 3NI Premium 13 53 19 8- Shaft Assembly, Mandrel 14 53 18-81 Housing, Mandrel 15 53 11 04-85 Bearing, Ball, Mandrel 19 53 19 65-39 Bolt, Shoulder 1 83 68 05-00 Nut, Crownlock 5/16-18 unc 3 53 19 5-5 Bracket, Deflector 4 53 10 53-04 Cap, Sleeve 5 53 19 0-6 Spring, Torsion, Deflector 6 53 11 04-5 Nut, Push 53 40 14- Shield, Deflector 9 53 13 14-91 Rod, Hinge 30 53 1 39-84 Screw Thdrol. Rolling Wsh. Hd. 31 53 18 6-90 Washer, Spacer 3 53 19 9-89 Pulley, Mandrel 33 53 40 0-34 Nut, Toplock, Flanged 34 8 11 06-1 Bolt Carr. Sh. 3/8-16 x 1-1/ Gr. 5 3 819 13 13-16 Washer 38 53 19 95-41 Keeper Belt LH Mandrel 40 83 90 06-00 Nut, Lock Flg. 3/8-16 unc 4 53 19 84-10 Spring Torsion Brake 43 53 19-56 Spring Torsion Retainer 46 53 13-9 Screw 1/4-0 x 5/8 55 53 19-49 Arm, Idler 56 53 19 90-9 Spacer, Retainer 5 81 00 06-16 Screw 3/8-16 x 1 59 53 14 10-43 Guard, Tuv. Idler 60 53 19 94-1 Arm Brake Mower 63 53 19 94-0 Arm Brake Mower 64 53 19 9-90 Link Brake 6 53 40 30-1 Handle Clutch Cable 68 53 40 83-81 V-Belt 69 8 14 05-05 Bolt 0 53 40 1-46 Clutch Asm. Manual 1 53 19-58 Keeper Belt Engine LH 13 53 19-59 Keeper Belt Engine RH 144 53 19 34-14 Keeper Belt 145 53 19 31-9 Pulley, Idler, Flat 14 53 40 18- Spring Return 15 53 40 8-14 Manual Clutch Cable 188 53 19 51-61 Stud Fastener 189 83 90 05-00 Nut Lock Hex Flange 195 81 00 06-1 Screw 3/8-16 x 3/4 199 53 40 00-95 Baffle Vortex 09 819 13 3-10 Washer 13/3 x x 10 - - 53 19 8-0 Mandrel Assembly (Includes housing, shaft and shaft hardware onlypulley not included) - - 53 40 04- Replacement Mower, Complete NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 15
SEAT ASSEMBLY 4 1 8 8 41 40 10 1 6 3 44 43 3 1 3 seat-tex_-vgt 1 53 19 5-18 Seat 53 18 01-66 Bracket Pivot Fender 3 53 14 06-5 Strap, Asm. Fender 6 83 80 06-00 Nut, Lock w/ins. 3/8-16 unc 53 1 41-81 Spring, Seat Cprsn. 8 53 1 18- Bolt 5/16-18 unc x 3/4 w/sems. 10 53 19 69- Pan, Seat 1 53 1 18-5 Bolt, Shoulder 5/16-18 3 83 80 05-00 Nut, Lock 5/16-18 unc 40 53 19 6-61 Handle 41 53 19 8-00 Spring 43 84 6 06-1 Bolt 3/8-16 unc x 3/4 44 819 13 38-1 Washer 13/3 x -3/8 x 1 Ga. NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 16
MOWER LIFT 45 8 8 90 98 10 89 3 9 100 88 9 91 101* 89 8 lift-tex_ *Key 91 may be substituted for Key 101 53 4 0- Shaft Asm., Cross Lift 3 53 19 5-31 Lever Asm., Lift RH 53 41 15-55 Grip, Lever 10 53 19 63-14 Spring Torsion 8 53 19 4-09 Pin Cotter /16 Bow Tie Lock 89 819 19 19-1 Washer Clear Zinc 90 53 19 4-08 Pin Cotter 5/16 Bow Tie Lock 91 53 19 51-81 Link Lift Susp. Mower Rear 9 81 00 06-1 Screw 3/8-16 x.5 Smgml. Tap/R.Z 98 53 19 5-0 Link Lift Susp. Front Mower 100 83 93 06-00 Nut Centerlock 3/8-16 101 53 40 0-03 Link Asm Lift NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 1