INSTALL GUIDE DOCUMENT NUMBER 97 REVISION DATE 08078 FIRMWARE ORB-AL(RS)-CH-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) ADS-HRN-CH (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately) Automotive Data Solutions Inc. 08
VEHICLE LIST - OF PAGE OF 0 DOC.: #97 08078 FEATURES MAKE MODEL I WARNING Install type & require a T-Harness (sold separately). Install type doesn't require a T-Harness. YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS X LOCK /STANDALONE MOD. PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DATA/MUX ER CTRL RAP SHUTDOWN CTRL RAM JEEP DODGE CHRYSLER 00 - or 00 / 00C 0-07 Aspen 07-0 or PT Cruiser 0-0 Sebring 07-0 or Avenger 08- or Caliber (with start wire) 07 Caliber 07- or Charger 0-07 Durango 07-0 or Magnum 0-07 Nitro 07- or Ram 00 07-08 or Ram 00 07-09 or Ram 00 07-09 or Ram 00 chassis cab 07-09 or Ram 00 chassis cab 08-0 or Ram 00 chassis cab 08-0 or Commander 0-07 Compass 07-7 or Grand Cherokee 0-07 Liberty 08- or Patriot 07-7 or Wrangler JK STD Key AT 07-8 or 00 chassis cab 0 or 00 chassis cab 0 or Automotive Data Solutions Inc. 08
BOX CONTENTS - OF PAGE OF 0 DOC.: #97 08078 BOX CONTENTS MODULE PIN WHITE CONNECTOR PIN BLACK CONNECTOR WHITE PROGRAMMING BUTTON LED 7 PIN WHITE CONNECTOR 0 PIN BLACK CONNECTOR WHITE WHITE 7 A B C F 0 9 8 7 BLACK PIN WHITE CONNECTOR DATA CABLE BLUE D E BLACK DATA PORT (WEBLINK, RF, TELEMATIC) PIN BLUE CONNECTOR DATA CABLE WEBLINK CABLE (required accessory sold separately) CH T-HARNESS (optional accessory sold separately) WEBLINK CABLE CH T-HARNESS MODULE DATA PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc. 08
COMPATIBLE ACCESSORIES - OF PAGE OF 0 DOC.: #97 08078 RF KIT (accessories sold separately) RF KIT AMPS FLASH RF DECODER BEFORE INSTALLATION MODULE DATA PORT V (+) RED BLACK BLACK BLUE BLUE CABLE RF DECODER BLACK CABLE ANTENNA Automotive Data Solutions Inc. 08
TYPE - WIRE CHART - OF PAGE OF 0 DOC.: #97 08078 MAKE CHRYSLER MODEL YEAR WIRE DESCRIPTION DODGE CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION JEEP COMPONENT LOCATOR 00 0-07 PT Cruiser 0-0 Caliber with start wire 07 Charger 0-07 Magnum 0-07 Commander 0-07 Grand Cherokee 0-07 Mux C Black pin Purple/Brown (MUX) Ignition switch ~ Starter C Black pin Pink/DkGreen (+) Ignition switch ~ Mux C Black pin Purple/Brown (MUX) Ignition switch ~ Starter C Black pin Pink/LtBlue (+) Ignition switch ~ Mux C Black pin Purple/Brown (MUX) Ignition switch ~ Starter C Black pin Pink/DkGreen (+) Ignition switch ~ Mux C Black pin Purple/Brown (MUX) Ignition switch ~ Starter C Black pin Pink/DkGreen (+) Ignition switch ~ Mux C Black pin Purple/Brown (MUX) Ignition switch ~ Starter C Black pin Pink/DkGreen (+) Ignition switch ~ Mux C Black pin Purple/Brown (MUX) Ignition switch ~ Starter C Black pin Pink/Orange (+) Ignition switch ~ Mux C Black pin Purple/Brown (MUX) Ignition switch ~ Starter C Black pin Pink/Orange (+) Ignition switch ~ Automotive Data Solutions Inc. 08
TYPE - WIRING DIAGRAM - OF PAGE OF 0 DOC.: #97 08078 MODULE A B F C D E DATA CUT AND INSULATE THE PURPLE WIRE (NEXT TO WHITE WIRE) A A VEHICLE IGNITION SWITCH SKIM CONNECTOR A B C D 7 PURPLE - ER (+) OUTPUT GREEN/RED - CONTROL (MUX) OUTPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH COMPATIBLE ACCESSORY ER (+) - 0 CONTROL (MUX) - 0 AFTERMARKET HOOD SWITCH (-) B IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. SKIM HARNESS A B E F 7 8 9 0 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) Automotive Data Solutions Inc. 08
TYPE - WIRE CHART - OF PAGE 7 OF 0 DOC.: #97 08078 MAKE MODEL CHRYSLER YEAR WIRE DESCRIPTION DODGE CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR 00 - Aspen 07-0 Sebring 07-0 Avenger 08- Caliber 07- Durango 07-0 Nitro 07- CanH ~ ~ 8 pin White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink (+) Ignition switch ~ V ~ ~ 8 pin Red (+) Ignition switch ~ CanH ~ ~ 8 pin White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink/Gray (+) Ignition switch ~ V ~ ~ 8 pin Red (+) Ignition switch ~ CanH ~ ~ 8 pin White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink (+) Ignition switch ~ V ~ ~ 8 pin Red (+) Ignition switch ~ CanH ~ ~ 8 pin White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink (+) Ignition switch ~ V ~ ~ 8 pin Red (+) Ignition switch ~ CanH ~ ~ 8 pin White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink/White (+) Ignition switch ~ V ~ ~ 8 pin Red/LtBlue (+) Ignition switch ~ CanH ~ ~ 8 pin White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/LtBlue (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink/Gray (+) Ignition switch ~ V ~ ~ 8 pin Red (+) Ignition switch ~ CanH ~ ~ 8 pin White/LtGreen (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink/White (+) Ignition switch ~ V ~ ~ 8 pin Red (+) Ignition switch ~ Automotive Data Solutions Inc. 08
TYPE - WIRE CHART - OF PAGE 8 OF 0 DOC.: #97 08078 MAKE MODEL DODGE JEEP YEAR WIRE DESCRIPTION RAM CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR Ram Pickup 07-0 Compass 07-7 Liberty 08- Patriot 07-7 Wrangler JK STD Key AT 07-8 Pickup 0 CanH ~ ~ 8 pin White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink/White (+) Ignition switch ~ V ~ ~ 8 pin Gray/Red (+) Ignition switch ~ CanH ~ ~ 8 pin White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink/White (+) Ignition switch ~ V ~ ~ 8 pin Red/LtGreen (+) Ignition switch ~ CanH ~ ~ 8 pin White/Black (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Blue (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink/White (+) Ignition switch ~ V ~ ~ 8 pin Red (+) Ignition switch ~ CanH ~ ~ 8 pin White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink/White (+) Ignition switch ~ V ~ ~ 8 pin Red/LtGreen (+) Ignition switch ~ CanH ~ ~ 8 pin White/Black (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/LtBlue (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink/White (+) Ignition switch ~ V ~ ~ 8 pin Red (+) Ignition switch ~ CanH ~ ~ 8 pin White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin Pink/White (+) Ignition switch ~ V ~ ~ 8 pin Gray/Red (+) Ignition switch ~ Automotive Data Solutions Inc. 08
TYPE - WIRING DIAGRAM - OF PAGE 9 OF 0 DOC.: #97 08078 MODULE VEHICLE IGNITION SWITCH A B F C D E DATA A 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 0 GREEN/RED (NC) 0 BLUE/YELLOW (NC) 0 BLUE/RED (NC) CANL - 07 CANH - 0 MUX - 0 IGNITION (+) - 0 V (+) - 0 A SKIM CONNECTOR 8 7 A B C D E 7 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE (NC) 0 ORANGE/WHITE (NC) 0 ORANGE/BLACK (NC) 0 BROWN/YELLOW - CANL 07 BROWN/RED - CANH 0 YELLOW - MUX 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) 0 WHITE - V (+) 0 WHITE/RED (NC) 0 WHITE/BLACK - IGNITION (+) OUTPUT 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 0 RED - V (+) V (+) REQUIRED WITHOUT COMPATIBLE ACCESSORIES OR DATA CABLE REQUIRED WITH COMPATIBLE ACCESSORIES F 7 8 9 0 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH (-) Automotive Data Solutions Inc. 08
TYPE - WIRING DIAGRAM - OF PAGE 0 OF 0 DOC.: #97 08078 MODULE VEHICLE IGNITION SWITCH A B F C D E DATA A A SKIM CONNECTOR A SKIM HARNESS A B C D 7 WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH COMPATIBLE ACCESSORY IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. AFTERMARKET HOOD SWITCH (-) E F 7 8 9 0 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) Automotive Data Solutions Inc. 08
MODULE PROGRAMMING PROCEDURE - STD KEY - OF PAGE OF 0 DOC.: #97 08078 0 Close driver door. 07 ACC ON Turn key to position. 0 Re-open driver door to wake up data bus. 08 Remove key. ACC ON 0 ACC ON Insert key into ignition. 09 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 0 ACC ON Turn key to ON position. 0 Wait, LED will turn solid GREEN for seconds. 0 LED will turn solid RED. Module Programming Procedure completed. 0 Within seconds, LED will flash GREEN rapidly. Automotive Data Solutions Inc. 08
VALET MODE PROGRAMMING PROCEDURE - OF PAGE OF 0 DOC.: #97 08078 NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. To exit valet mode: repeat steps to. 0 Time restriction. Complete next step within 7 seconds. 0 ACC ON Cycle ignition ON five times [x /ON] rapidly. ENGINE STOP 0 Wait, LED will turn solid RED for seconds. 0 ACC ON Set ignition to position. ENGINE STOP 0 Valet Mode Programming Procedure completed. Automotive Data Solutions Inc. 08
AFTERMARKET REMOTE PROGRAMMING PROCEDURE - OF PAGE OF 0 DOC.: #97 08078 WARNING: Program aftermarket remotes before usage. A maximum of four [x] aftermarket remotes per system. 0 LED will flash GREEN once [x]. 0 Time restriction. Complete next step within 7 seconds. 07 LED will turn solid RED. 0 ACC ON Cycle ignition ON five times [x /ON] rapidly. To program additional remotes: repeat steps to 7 using each additional remote. ENGINE STOP 0 LED will turn solid RED. 08 Wait, LED will turn. 0 Time restriction. Complete next step within seconds from previous step. 09 ACC ON Set ignition to position. ENGINE STOP 0 Press once [x] on LOCK button of aftermarket remote. 0 Aftermarket Remote Programming Procedure completed. Automotive Data Solutions Inc. 08
PAGE OF 0 MODULE NAVIGATION PROCEDURE - OF It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 Module must be programmed to the vehicle. 0 Use the Module Navigation Chart on the next page. 0 Set ignition to position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 ACC ON DOC.: #97 08078 TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE STOP 0 0 [X] Automotive Data Solutions Inc. 08
MODULE NAVIGATION CHART - OF PAGE OF 0 DOC.: #97 08078 MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. 08 0 DISARM/UNLOCK BEFORE 0 0 ON 0 RELOCK AFTER 0 0 ON 0 RELOCK AFTER SHUTDOWN 0 0 ON 0 FORCE UNLOCK ALL ON FIRST PRESS 0 0 ON 0 TAKEOVER 0 ENABLE 0 DISABLE* 0 SEC 0 SECURE TAKEOVER DELAY 0 90 SEC 0 0 MIN 0 0 MIN 0 DISABLE 07 FACTORY KEYLESS RS SEQUENCE 0 N/A 0 LOCK + UNLOCK + LOCK 0 CONFIGURATION 0 LOCK + LOCK + LOCK 0 0 MIN 0 0 MIN 0 0 MIN 08 MODULE RUN TIME 0 MIN 0 MIN 0 0 MIN 07 MIN 08 MIN 0 0 SEC 0 0 SEC 0 08 SEC 09 WAIT TO DELAY 0 0 SEC 0 SEC 0 0 SEC 07 SEC 08 0 SEC 0- N/A 0 N/A 0-07 Technical Support only 0 N/A 0 N/A
REMOTE ER ERROR CODES - OF PAGE OF 0 DOC.: #97 08078 REMOTE ER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash three [x] times, then will flash [X] number times to indicate an error code. See table. 0 Engine running. 0 Key in ignition at ON position. 0 N/A 0 Trunk is open. 0 Foot brake is ON. 0 Hood is open. 07 N/A 08 Tach failure. 09 N/A 0 System is in Valet Mode. REMOTE ER SHUTDOWN ERROR CODES: NOTES [Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for. seconds when using a -WAY remote. OR Press once [x] on button when using a -WAY remote. The parking lights will flash four [x] times, then will flash [Y] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 N/A 0 Foot brake is ON. 0 Hood is open. 0 Engine RPM limiter is ON. 0 Glow plug timeout error. 07 Vehicle is moving (VSS). 08 Check engine warning light is ON. 09 Low fuel warning light is ON. Automotive Data Solutions Inc. 08
MODULE DIAGNOSTICS - OF PAGE 7 OF 0 DOC.: #97 08078 TEST MODULE LED STATUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE WITH IGNITION Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence. Automotive Data Solutions Inc. 08
MODULE RESET PROCEDURE - OF PAGE 8 OF 0 DOC.: #97 08078 0 Disconnect all connectors from module except the BLACK -PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK -PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK -PIN connector. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. Automotive Data Solutions Inc. 08
TAKEOVER PROCEDURE - STD KEY - OF PAGE 9 OF 0 DOC.: #97 08078 All vehicle doors must be closed and locked prior to remote start sequence. Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. ACC ON 0 ACC ON Turn key to ON position. 0 Press and release BRAKE pedal. 0 Take over procedure completed. Automotive Data Solutions Inc. 08
INSTALLATION CHECKLIST - OF PAGE 0 OF 0 DOC.: #97 08078 WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question : Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. Question : Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question : Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. Enter vehicle and close the doors. Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc. 08