NMB (X) -MFT Proportional Control, Non-Spring Return, Direct Coupled, V, Multi-Function Technology Torque min. 90 in-lb for control of damper surfaces up to sq ft. Technical Data NMB(X)-MFT Power Supply VAC ± 0% 0/60 Hz VDC ± 0% Power Consumption. W (. W) Transformer Sizing. VA (Class power source) Electrical Connection 8 GA plenum rated cable / conduit connector ft [m] ( 0 ft [m] 6 ft [m]) Overload Protection Operating Range Y Input Impedance Feedback Output U Angle of Rotation Torque electronic throughout 0 to 9 rotation to 0 VDC, to 0 ma (default) Variable (VDC, PWM, Floating Point, On/Off) 00 kω (0. ma), 00Ω 00 Ω (PWM, Floating Point, On/Off) to 0 VDC, 0. ma max, VDC Variable max. 9, adjust. with mechanical stop electronically variable 90 in-lb [0 Nm] Direction of Rotation reversible with switch Position Indication Manual Override Running Time Humidity reflective visual indicator (snap-on) external push button 0 seconds (default) Variable ( to 70 secs) to 9% RH non condensing (EN 6070-) Ambient Temperature - F to + F [-0 C to +0 C] Storage Temperature Housing Housing Material Agency Listings -0 F to +76 F [-0 C to +80 C] NEMA /IP UL9-VA Noise Level Servicing Quality Standard ISO 900 Weight. lbs [0.9 kg] culus acc. to UL 6070-A/--, CAN/CSA E6070-, CSA C. No. -9, CE acc. to 89/6/EEC <db(a) maintenance free Rated Impulse Voltage 800V, Type of action, Control Pollution Degree. Application For proportional modulation of dampers in HVAC systems. Actuator sizing should be done in accordance with the damper manufacturer s specifications. The actuator is mounted directly to a damper shaft up to.0" in diameter by means of its universal clamp, / self centered default. A crankarm and several mounting brackets are available for applications where the actuator cannot be direct coupled to the damper shaft. The default parameters for to 0 VDC applications of the actuator are assigned during manufacturing. If necessary, custom versions of the actuators can be ordered. The parameters can be changed by two means: pre-set and custom configurations from Belimo or on-site configurations using the Belimo PC-Tool software. Operation The actuator is not provided with and does not require any limit switches, but is electronically protected against overload. The anti-rotation strap supplied with the actuator will prevent lateral movement. The NMB(X) series provides 9 of rotation and a visual indicator indicates position of the actuator. When reaching the damper or actuator end position, the actuator automatically stops. The gears can be manually disengaged with a button on the actuator cover. The NMB(X)-MFT actuators use a Brushless DC motor, which is controlled by an Application Specific Integrated Circuit (ASIC). The ASIC monitors and controls the actuator s rotation and provides a digital rotation sensing (DRS) function to prevent damage to the actuator in a stall condition.power consumption is reduced in holding mode. Add on auxiliary switches or feedback potentiometers are easily fastened directly onto the actuator body for signaling and switching functions Dimensions (All numbers in brackets are in millimeters.) / to.0 [.7 to 6.67] / to.0 [0 to 6.67]." [6.]." [80].66" [9] 0.98" [].7" [0.] 7.7" [96.] " [0.8] D J07 - Subject to change. Belimo Aircontrols (USA), Inc. 90
NMB (X) -MFT Proportional Control, Non-Spring Return, Direct Coupled, V, Multi-Function Technology Accessories K-NA ZG-00 ZG-0 ZG-0 ZG-0 ZG-NMA AV8- ZG-NMSA- ZS-00 ZS-0 Tool-06 SA, SA P70 P A SGA SGF ADS-00 ZG-R0 Wiring Diagrams Reversible Clamp Crankarm Adaptor Kit Universal Shaft Extension Shaft Adaptor Weather Shield - Steel Weather Shield - Polycarbonate 8 mm & 0 mm Wrench Auxiliary Switch (es) Shaft Mount Auxiliary Switch Feedback Potentiometers Min positioners in NEMA housing Min positioners for flush panel mounting Analog to Digital Switch Resistor for to 0 ma Conversion NSV US Battery Back-Up Module ZG-X0 Transformer Note: When using NMB(X)-MFT actuators, only use accessories listed on this page. NMB(X)-MFT - Typical Specification: Proportional control damper actuators shall be electronic direct-coupled type, which require no crankarm and linkage and be capable of direct mounting to a shaft up to.0 diameter. Actuators must provide proportional damper control in response to a to 0 VDC or, with the addition of a 00Ω resistor, a to 0 ma control input from an electronic controller or positioner. Actuators shall have Brushless DC motor technology and be protected from overload at all angles of rotation. Actuators shall have reversing switch and manual override on the cover. Run time shall be constant and independent of torque. Actuators shall be culus listed, have a -year warranty, and be manufactured under ISO 900 International Quality Control Standards. Actuators shall be as manufactured by Belimo. NM J07 - Subject to change. Belimo Aircontrols (USA), Inc. VDC/-0 ma VAC Transformer Control Signal to 0 ma or to 0 VDC PWM On/Off Position (+) Ω 00Ω / watt VAC/DC Transformer Feedback VDC (+) 6 VAC Transformer (AC only) Position Feedback VDC (+) a Blk () Common Red () + Hot Wht () Y Input, to 0V Org () U Output, to 0V Blk () Common Red () + Hot Wht () Y Input Org () U Output Blk () Common Red () Hot Wht () Y Input Org () U Output Floating Point Notes: Provide overload protection and disconnect as required. Actuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. Actuators may also be powered by VDC. VAC Transformer to 0 VDC Feedback Signal A B 7 Blk () Common Red () Hot + Wht () Y Input Pnk () Y Input Org () U Output to 0V Position feedback cannot be used with a Triac sink controller. The actuator internal common reference is not compatiable. Control signal may be pulsed from either the Hot (Source) or Common (Sink) VAC line. 6 ZG-R0 may be used. Contact closures A & B also can be triacs. A & B should 7 both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator 8 must be connected to the hot connection of the controller. 8 W99 9
Installation and Operation Non-Spring Return Table of Contents Page General Mounting Standard...66 Reversible Clamp...67 ar...68 Rotary...69 Retrofit Brackets...7 Operation Electrical...7 Mechanical...7 Wiring General...7 Accessories...7 Startup and Checkout...78 General Information Preliminary Steps. Belimo actuators with NEMA or NEMA ratings should be mounted indoors in a dry, relatively clean environment free from corrosive fumes. If the actuator is mounted outdoors, a protective enclosure must be used to shield the actuator.. For new construction work, order dampers with extended shafts. Instruct the installing contractor to allow space for mounting the Belimo actuator on the shaft. For replacement of existing gear train actuators, there are two options: A. From a performance standpoint, it is best to mount the actuator directly onto the damper shaft. B. If the damper shaft is not accessible, mount the nonspring return actuator with a ZG-NMA or ZG-GMA crankarm kit, and a mounting bracket (ZG-00, ZG- 0, ZG-0, ZG-0) J07 - Subject to change. Belimo Aircontrols (USA), Inc. Determining Torque Loading and Actuator Sizing Damper torque loadings, used in selecting the correct size actuator, should be provided by the damper manufacturer. If this information is not available, the following general selection guidelines can be used. Damper Type Torque Loading Opposed blade, without edge seals, in-lb/sq. ft. for non-tight close-off applications Parallel blade, without edge seals, in-lb/sq. ft. for non-tight close-off applications Opposed blade, with edge seals, in-lb/sq. ft. for tight close-off applications Parallel blade, with edge seals, 7 in-lb/sq. ft. for tight close-off applications The above torque loadings will work for most applications under in. w.g. static pressure or 000 FPM face velocity. For applications between this criteria and in. w.g. or 00 FPM, the torque loading should be increased by a multiplier of.. If the application calls for higher criteria up to in. w.g. or 000 FPM, use a multiplier of.0. Multiple Actuator Mounting 0 0 00 80 60 0 0 0 6 8 0 7 9 If more torque is required than one GM can provide, GMB, GMB-SR or GMX-MFT may be installed on the same shaft. Damper Area (sq. ft.) Torque Loading Chart Torque Loading (in-lb/ sq. ft.) 6
Installation Instructions Quick-Mount Visual Instructions for Mechanical Installation C A B D 0 See next page for standard mounting instructions. A* B C** D LM / to / /6 to /. to ft-lb NM / to.0 / to.0. 6 to 7 ft-lb AM / to.0 / to.0. 6 to 7 ft-lb GM / to.0 / to.0. 6 to 7 ft-lb J07 - Subject to change. Belimo Aircontrols (USA), Inc. 6 *LM standard clamp has max /8 diameter. Accessory clamp K-LM0 can be mounted for sizes up to / diameter. NM, AM and GM clamps have an insert that self-centers on the following diameter shafts: / (default), / and.0. **Shorter with reversible clamp for NM, AM, and GM 66
Mounting Installation Reversible Clamp Quick Mount (NM, AM, GM) J07 - Subject to change. Belimo Aircontrols (USA), Inc. Standard Mounting. Turn the damper shaft until the blades are fully closed.. Slip the actuator s universal clamp over the damper shaft. Make sure that the duct and the controls on the cover are accessible. Place the actuator in the desired mounting position. ➁ Hand tighten the two nuts on the actuators universal clamp.. Disengage the actuator gear train by pressing the manual override button and rotate the clamp until centered. ➁ Slide the anti-rotation strap up under the actuator so it engages the actuator at the center cutout. Bend the bracket as needed to support the rear of the actuator. Secure to ductwork with self-tapping screws (No. 8 recommended).. Loosen the nuts on the universal clamp. Press the manual override button and rotate the clamp to about from the closed position (/6 to /8 between stop and clamp). ➁ Tighten the two nuts on the universal clamp with a 0 mm wrench (see table for required torque).. Snap on the reflective position indicator. ➁ Adjust end-stops, if required 6. Mount actuators indoors. If mounted outdoors, use approved protective enclosure. The damper is now fully closed but the actuator is from fully closed. This is called pre-loading the actuator. When the actuator is powered and sent to the closed position: it will put its full torque on the shaft compressing the edge and blade seals. This ensures that the damper will meet its leakage rating. The actuator is electronically protected from overload and will not be damaged. Testing the Installation Without Power. Disengage the gear train with the manual override button and move the shaft from closed to open to closed. Ensure that there is no binding and that the damper goes fully open and closes with of actuator stroke left.. Correct any problems and retest. 67