INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2008 CR-V Publications No. AII 35843-38422 Issue Date DEC 2007 PARTS LIST Caution label Remote Engine Starter Kit P/N 08E91-E22-100B Transmitter Accessory User s Information Manual Control unit Quick Start Guide Antenna Remote Control Engine Starter Attachment (With Vehicle Security) P/N 08E92-SWA-100 Engine starter harness Key ring Control unit bracket Protective tape Fuse label Template 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 08E92-SWA-1000-91 1 of 27

Bracket Flange nut, 6 mm 3 Relays Remote Engine Starter Attachment Kit (Without Vehicle Security) P/N 08E92-SWA-100A Engine starter harness 19 Wire ties Hood switch harness 2 Wire ties with clips Hood lock Clip Control unit bracket 11 Foam cushion tapes Template Washer bolt, 6 x 12 mm Bracket 2 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

3 Relays Flange nut, 6 mm 2 Spacers 25 Wire ties 2 Wire ties with clips Clip A Clip B 11 Foam cushion tapes TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver Flat-tip screwdriver Diagonal cutters Ratchet 8 mm Socket 10 mm Socket 12 mm Deep socket 10 mm Combination wrenches 10 mm Wrench Hook tool Felt-tip pen Isopropyl alcohol Electrical tape Scissors Small flat-tip screwdriver T25 Torx bit Shop towel Scale Rubber mallet HDS (Honda Diagnostic System) Torque wrench Fender cover Masking tape Needle nose pliers Washer bolt, 6 x 12 mm 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 3 of 27

Illustration of the Engine Starter Installed on the Vehicle With Vehicle Security FUSE (3A, 3A) INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: This antenna should only be installed if the ambient air temperature 15 C (60 F) or above. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. 3. Turn the knob of the driver s seat side under cover. Remove the driver s seat side under cover (a pin and a clip). FUSE CASE (30A, 40A) Without Vehicle Security CONTROL UNIT 6D0404AK FUSE CASE (30A, 40A) KNOB (Turn.) PIN FUSE (3A, 3A) HOOD LOCK DRIVER S SEAT SIDE UNDER COVER CLIP 6303080B HOOD SWITCH CONTROL UNIT 6D0405AK 4 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

4. Remove the driver s side lower dash cover (seven clips and two hooks). Take care not to damage the clips and hooks. 6. Pull out the front door opening seal and remove the driver s seat side kick panel (two clips). 2 CLIPS 7 CLIPS FRONT DOOR OPENING SEAL (Pull out.) DRIVER S SIDE LOWER DASH COVER HOOKS 6303071B 5. Remove the left front side step trim (three clips). 3 CLIPS DRIVER S SEAT SIDE KICK PANEL 6303100B 7. Lower the tilt lever and pull steering wheel outward. Insert a flat-tip screwdriver into the guide on the under side of the steering column lower cover and release the retaining tab. 8. Remove the steering column upper cover (four retaining tabs). STEERING COLUMN UPPER COVER Push. LEFT FRONT SIDE STEP TRIM STEERING COLUMN LOWER COVER 6303090B RETAINING TAB TILT LEVER FLAT-TIP SCREWDRIVER GUIDE 7215010K 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 5 of 27

9. Remove the steering column lower cover (two self-tapping screws and one screw). 11. Remove the map light (four bolts and disconnect the vehicle connectors). STEERING COLUMN LOWER COVER MAP LIGHT SELF-TAPPING SCREWS SCREW 6819030Y 4 BOLTS 6313021Y 10. Remove the map light lenses (two retaining tabs each). 12. Using a flat-tip screwdriver, remove the right and left sunvisor holders. MAP LIGHT LEFT SUNVISOR HOLDER 2 RETAINING TABS LENS 2 RETAINING TABS LENS 6522020Y Push. FLAT-TIP SCREWDRIVER Turn. RIGHT SUNVISOR HOLDER 6308170Y 6 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

13. Pull away the weatherstrip from the left front A-pillar trim. PIN Strike perpendicularly to the vehicle. CLIP 14. Using a small rubber mallet and a shop towel, gently tap the left front A-pillar trim at the position shown to release the clip. 15. Pull away the weatherstrip from the left front A-pillar trim. Remove the left front A-pillar trim (two clips). LEFT FRONT A-PILLAR TRIM 3 CLIPS PIN LEFT FRONT A-PILLAR LEFT FRONT A-PILLAR TRIM LEFT FRONT A-PILLAR TRIM DOOR OPENING SEAL CLIP TRIANGLE MARK RUBBER MALLET STRIKE POINT SHOP TOWEL 7212011S DOOR OPENING SEAL 6227020H 16. Remove and discard the clip from the left front A-pillar, and install a new A-pillar (supplied) clip on the left front A-pillar trim. LEFT FRONT A-PILLAR LEFT FRONT A-PILLAR TRIM NEW CLIP CLIP (Discard.) 720903AK 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 7 of 27

Installing the Antenna 17. Using two pairs of needle nose pliers, bend the antenna plate according to the dimensions shown. 18. Using scissors, cut out the template. Cut out. PLATE 24 mm (0.9 in.) TEMPLATE 24 mm (0.9 in.) 19. Using tape, secure the template to the windshield by aligning it with the edge of the black ceramic paint. REARVIEW MIRROR BLACK CERAMIC PAINT NEEDLE NOSE PLIERS EDGE OF BLACK CERAMIC PAINT SCALE PLATE 6N3001CK WINDSHIELD TEMPLATE TAPE Align these ends with the ends of the black ceramic paint. 6N3002AK 8 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

20. Starting near the end of the antenna cable, wrap three foam cushion tapes and three half foam cushion tapes around the antenna cable at the measurements shown. 22. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach. Allow the alcohol to dry before proceeding. FOAM CUSHION TAPE 390 mm (15 in.) 30 mm (1.2 in.) 720 mm (28 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) PLATE TEMPLATE 30 mm (1.2 in.) ADHESIVE BACKING 6N3004BK Cut. FOAM CUSHION TAPE HALF FOAM CUSHION TAPE 6N3003AK 21. Using scissors, cut one foam cushion tape to the measurement shown. Attach the cut piece of foam cushion tape to the antenna plate as shown. 23. Remove the adhesive backing from the antenna, insert the antenna plate under the roof lining, and attach the antenna to the windshield aligning the template. 24. Remove the template. 25. Push the antenna cable into the roof lining as shown. Be careful not to crease the roof lining. Cut. 60 mm (2.4 in.) 15 mm (0.6 in.) ROOF LINING FOAM CUSHION TAPE Align. PLATE 6N30050K 780101BK 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 9 of 27

26. Clean the vehicle panel surface where the foam cushion tape will attach using isopropyl alcohol. Secure the antenna cable to the vehicle panel with the remaining piece of foam cushion tape you cut in step 21. Be careful not to crease the roof lining. PANEL 28. Route the antenna cable along the left front A-pillar and secure it to the vehicle harness with the five wire ties as shown. 5 WIRE TIES CLIP FOAM CUSHION TAPE FOAM CUSHION TAPE (From step 21.) LEFT FRONT PILLAR FOAM CUSHION TAPE 6N3006BK 27. Clean the vehicle panel surface where the foam cushion tape will attach using isopropyl alcohol. Secure the antenna cable to the vehicle panel using one foam cushion tape. Be careful not to crease the roof lining. 29. Pull away the door opening seal. Route the antenna cable down under the dashboard. Tuck the antenna cable between the left front pillar and the dashboard, and reinstall the door opening seal. DOOR OPENING SEAL 720905AK LEFT FRONT PILLAR DASHBOARD PANEL FOAM CUSHION TAPE 751650AK 6N30070K 10 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

Setting the Control Unit 30. Get the control unit. Using a small flat-tip screwdriver, adjust the switches on the (accessory) control unit to the locations shown. Using isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Remove the adhesive backing, and attach the protective tape to the control unit. NOTE: If the switch setting is not correct, the engine starter will not operate properly. If setting the switches with the control unit installed in the vehicle, touch a metal part of the screwdriver to any metal part of the vehicle to dicharge any static electricity. If you change the switch settings with the unit connected, you must disconnect the unit then reconnect it before the settings change. Routing the Engine Starter Harness 31. Route the engine starter harness under the dashboard area as shown. SWITCH 721307BK CONTROL UNIT 32. Attach the 30A, 40A, and 3A fuse labels to the relay block and the fuse case of the engine starter harness. PROTECTIVE TAPE Clean with isopropyl alcohol. RELAY RELAY BLOCK 40A FUSE LABEL ADHESIVE BACKING SW:1 RR Junction Unit SW:2 Trunk or Tailgate SW:3 Smart Entry SW:4 Horn or Buzzer Answer Back SW:5 Trunk Main SW SW:6 Reserve 720901AK 3A FUSE LABEL 30A FUSE LABEL 33. Install the three relays to the relay block of the engine starter harness. 6N3008BK 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 11 of 27

34. Unlock the vehicle 42-pin connector by pushing the retaining tab on the connector, and disconnect the connector from the fuse box. 42-PIN 4-PIN Push. 2-PIN 2-PIN 38. Plug the engine starter harness 4-pin and 2-pin connectors into the fuse box. Check that the engine starter harness 4-pin and 2-pin connectors are connected to the fuse box and they are locked securely. A loose connector can cause a engine to stall. Pull on the connector to verify it s locked properly. 42-PIN FRONT VIEW RETAINING TAB FUSE BOX 4-PIN 751701AK 2-PIN 35. Disconnect the vehicle 4-pin connector, and the 2-pin connector from the top of the fuse box. 36. Wrap one foam cushion tape around the vehicle 4-pin connector and one around the 2-pin connector. FOAM CUSHION TAPE 4-PIN AND 2-PIN 4-PIN 752101BK 39. Reconnect the vehicle 42-pin connector to the fuse box. 40. Route the antenna cable as shown. GROUND TERMINAL GROUND BOLT (Reuse.) WIRE TIE 751702AK 37. Secure the vehicle 4-pin connector and 2-pin connector to the vehicle harness using one wire tie. 752102AK 41. Remove the ground bolt from the vehicle. Secure the engine starter harness ground terminal using the ground bolt you just removed. 12 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

42. Disconnect the vehicle 20-pin connectors from the right side of the fuse box, and plug them into the engine starter harness 20-pin connectors. 44. Disconnect the vehicle 24-pin connectors from under the fuse box, and plug them into the engine starter harness 24-pin connectors. FUSE BOX 20-PIN FUSE BOX 24-PIN 20-PIN 24-PIN 20-PIN S 24-PIN 24-PIN S 752105BK 20-PIN S 752103AK 43. Disconnect the vehicle 23-pin connectors from under the fuse box, and plug them into the engine starter harness 23-pin connectors (white). 23-PIN S (WHITE) FUSE BOX 45. Attach the engine starter harness 24-pin connector to the vehicle 24-pin connector. 46. If the vehicle is equipped with the factory security system, secure the engine starter harness 2-pin connector (white) to the vehicle harness, it will not be used. If the vehicle is not equipped with the security system, the connector will be used in a later step. 23-PIN 5 WIRE TIES 23-PIN (Blue) 23-PIN S 752104BK WIRE TIE (if vehicle is equipped with factory security system) 752106BK 47. Secure the engine starter harness 23-pin connector (blue), and the engine starter harness to the engine starter harness and vehicle harness using three wire ties. 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 13 of 27

48. Attach the wire tie with clip to the engine starter harness and the antenna cable at the green tape then push the clip into the hole in the steering hanger beam. 50. Attach the wire tie with clip to the engine starter harness and the antenna cable at the other green tape, then push the clip into the hole in the bracket. STEERING HANGER BEAM GREEN TAPE WIRE TIE WITH CLIP WIRE TIE WITH CLIP GREEN TAPE BRACKET 721203AK 49. Install the bracket to the instrument panel using one 6 x 12 mm washer bolt, and one 6 mm flange nut. INSTRUMENT PANEL 7212040K 51. Route the engine starter harness 7-pin connectors (brown, green, white) towards the steering column. 7-PIN STEERING COLUMN 7-PIN 6 x 12 mm WASHER BOLT 6 mm FLANGE NUT BRACKET 6310061Y 6D01120Y 14 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

52. Disconnect the vehicle 7-pin connector (brown) from the ignition switch and connect the engine starter harness 7-pin connector (brown) as shown. 55. Insert the vehicle 7-pin connector (brown) into the gap on the steering column. Check that the engine starter harness 7-pin connector (brown) is connected to the vehicle connector and it is locked securely. A loose connector can cause engine stall. 7-PIN (brown) PANEL 7-PIN (brown) IGNITION SWITCH GREEN TAPE FOAM CUSHION TAPE WIRE TIE 7212050K Pull on the connector to verify that it s locked properly. 7-PIN (brown) 721301AK 53. Wind one foam cushion around the vehicle 7-pin connector (brown). 54. Disconnect the vehicle 7-pin connector (white) from the ignition switch, and plug in the engine starter harness 7-pin connector (white) as shown. 56. Secure the engine starter harness to the vehicle harness using two wire ties. 57. Disconnect the vehicle 8-pin connector (black) from the wiper switch, and plug the engine starter harness 8-pin connector to the wiper switch. 8-PIN (black) 8-PIN 7-PIN (white) IGNITION SWITCH 7-PIN (white) WIPER SWITCH 6D01160Y 7213020K 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 15 of 27

58. Plug the vehicle 8-pin connector (black) to the engine starter harness 8-pin connector. 8-PIN (black) 61. Align the green tape on the engine starter harness with the vehicle harness clip, and secure the engine starter harness to the vehicle harness with one wire tie. GREEN TAPE WIRE TIE WIRE TIE 8-PIN (Black) 6D01171Y CLIP RELAY BLOCK FRAME 59. Secure the engine starter 8-pin connector (black) to the vehicle harness using one wire tie. 60. Attach the engine starter harness to the fuse case of the vehicle relay block. RELAY BLOCK FUSE CASE 721304AK 62. Secure the engine starter harness relay block to the vehicle frame. 63. Remove the vehicle nut. Secure the control unit bracket to the vehicle frame using the vehicle nut you just removed. STEERING SHAFT 7213030K NUT (Reuse.) FRAME CONTROL UNIT BRACKET 6N3009AK 16 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

64. Connect the antenna cable terminal to the control unit as shown. 67. Secure the engine starter harness and antenna cable to the engine starter harness using two wire ties. WIRE TIE CONTROL UNIT (Bundle the excess.) CONTROL UNIT TERMINAL (Connect first.) 28-PIN 6D0402BK 65. Plug the engine starter harness 28-pin connector into the control unit. 66. Slide the control unit onto the control unit bracket. WIRE TIE 6D0403AK 68. Bundle the excess antenna cable, and secure it to the engine starter harness using two wire ties. 69. Clean the steering column lower cover on the bracket surface where the urethane foam will attach using isopropyl alcohol. Attach the urethane foam to the bracket. URETHANE FOAM CONTROL UNIT BRACKET CONTROL UNIT BRACKET 6D0401AK STEERING COLUMN LOWER COVER 752201AK 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 17 of 27

If the vehicle is equipped with a factory security system, go to step 85; otherwise, continue with step 70. 70. Remove the seven clips from the radiator cover. 72. Remove the four self-tapping screws from the left inner fender. LEFT INNER FENDER 2 CLIPS B 5 CLIPS A RADIATOR COVER 621501AP 71. Remove the left fender well trim (two self-tapping screws and seven clips). Using isopropyl alcohol on a shop towel, clean the areas where the spacer will attach. Replace the existing two spacers with new spacers from the kit as shown. 73. Remove the six clips, and turn down the left inner fender. LEFT INNER FENDER 4 SELF-TAPPING SCREWS 771301AK SPACER OLD SPACER ADHESIVE BACKING Remove. 6 CLIPS LEFT FENDER WELL TRIM 6 CLIPS 771302AK SELF-TAPPING SCREWS CLIP 721305AK 18 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

74. Using a felt-tip pen, mark around the vehicle hood lock at its existing location for proper reinstallation. 77. Install the new hood lock with the three bolts you removed, and align it with the marks you made. Torque the hood lock bolts to: 10 N m (7.2 lbf-ft) HOOD LOCK MARK FELT-TIP PEN MARK HOOD LOCK BOLT BOLT (Reuse.) 6311080Y 75. Remove and discard the hood lock (three bolts, and remove the hood lock opener cable). 76. Attach the hood lock opener cable to the new hood lock. 6311100Y 78. Route the grommet side of the hood switch harness from the engine compartment into the left fender area as shown. HOOD LOCK (Discard.) GROMMET LEFT FENDER SIDE FRONT HOOD LOCK OPENER NEW HOOD LOCK HOOD SWITCH 6311090Y COMPARTMENT 6831010Y 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 19 of 27

79. Route the hood switch harness as shown, and secure the hood switch harness to the vehicle panel using the three clips installed on the hood switch harness. 82. Route the hood switch harness along the vehicle harness towards the center of the vehicle. Secure the hood switch harness to the vehicle harness using six wire ties. FRONT HOOD SWITCH GREEN TAPE FRONT GREEN TAPE 6 WIRE TIES PANEL CLIP B 3 HOOD SWITCH CLIPS 6311122Y 80. Attach clip B to the hood switch harness at the green tape, and secure it to the vehicle panel. 81. Remove and discard the vehicle grommet. Route the hood switch harness 2-pin connector into the passenger s compartment. 83. Plug the hood lock 2-pin connector into the hood switch harness 2-pin connector, and secure the connector to the vehicle panel. HOOD SWITCH HOOD SWITCH 2-PIN 6311142Y FRONT HOOD SWITCH HOOD LOCK 2-PIN GROMMET INSIDE OUTSIDE Install the grommet noting installation direction. GROMMET (Discard.) 6311113Y PANEL 6311150Y 20 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

84. Plug the hood switch harness 2-pin connector, (routed in step 79), to the engine starter harness 2-pin connector. Secure the connector to the vehicle harness using one wire tie. 85. Using isopropyl alcohol on a shop towel, clean the area where the caution label will attach. HOOD 2-PIN ADHESIVE BACKING WIRE TIE 2-PIN HOOD SWITCH 2-PIN 752202AK CAUTION LABEL 6D2401AK 86. Attach the caution label to the hood. 87. Reinstall all removed parts. Check that all clips and fasteners are installed securely. Take care not to pinch the airbag with a clip during reinstallation of the front pillar trim. Do not push the front pillar trim excessively. 88. Reconnect the negative cable to the battery. 89. Do the REMOTE REGISTRATION (page 23) and FUNCTION CHECK (page 26). 90. Enter the customer s radio anti-theft code, and reset the radio station presets. 91. Reset the clock. 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 21 of 27

SETTING THE AUTOMATIC DEFROST FUNCTION (IF EQUIPPED WITH AUTOMATIC CLIMATE CONTROL) Setting the automatic defrost function must be done with the air conditioner off. Turn the air conditioner to off position with the ignition switch in the ON (II) position, then turn the ignition switch to the LOCK (0) position before setting. While holding the REAR DEFOGGER switch and the RECIRCULATION switch, turn the ignition switch to the ON (II) position for at least 10 seconds. The Set temperature and a letter (CL or AC) on the air conditioner display will blink after 5 seconds, and stays on after 10 seconds. The letter CL indicates that the automatic defrost function is OFF, and the letter AC indicates that the automatic defrost function is ON. 5 Seconds after turning the ignition switch to ON (II) (indicating current setting) REAR DEFOGGER switch RECIRCU- LATION switch IGNITION switch 0 II 10 Seconds after turning the ignition switch to ON (II) 5419160K 5718220S 22 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

REMOTE REGISTRATION 1. Acquire the PCM code from the Interactive Network. 2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the ON (II) position. 3. Start the HDS, and click the car icon. 5. Select Honda Systems, then click the check button. CAR ICON Select Honda Systems. CHECK BUTTON 752503AS 6. Select R/C ENG and click the check button. 752501AS 4. Input the VIN and other required information into the HDS, then click the check button. Select R/C ENG. CHECK BUTTON 752504AS Input the VIN and other required information. CHECK BUTTON 752502AS 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 23 of 27

7. A REMARKS message will display. Click the check button. REMARKS message 9. The following message will display: Obtain PCM-code (IMMOBILIZER PCM CODE) from in. This vehicle s VIN will be required to obtain the password. (USA). Click on the check button. Obtain PCM-code message CHECK BUTTON 752505AS 8. Select REGISTER REMOTE CONTROL UNIT, then click the check button. CHECK BUTTON 752507AS 10. Input the PCM code, then click on the check button. NOTE: To ensure security, the PCM code (password) is changed every day, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same. Input the PCM code. Select REGISTER REMOTE CONTROL UNIT. CHECK BUTTON 752506AS CHECK BUTTON 752509AS 24 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click on the check button. The registration of the Remote Control Engine Starter Unit has been completed. CHECK BUTTON 752510AS 12. The following message will display: Check that the engine can be started by the Transmitter. Click on the check button. Check that the engine can be started by the Transmitter. CHECK BUTTON 13. Perform the Function check test on page 26, then disconnect the HDS. 752511AS 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 25 of 27

FUNCTION CHECK Operating Conditions The hood is closed. The shift lever is in Park. The key is not in the ignition switch. All doors and tailgate closed and locked. Inspection 1. Within 1 second, press the command button and then the start button on the transmitter. The engine should start if all operating conditions are met. Does the engine start? Yes - Operation is normal. No- Make sure all operating conditions are met. Check the engine starter harness connections. Connect the HDS and check for an indicated failure. (Refer to the appropriate service manual for details.) 2. Press the command button on the transmitter, and within 1 second, press the stop button. The engine should stop. Does the engine stop? Yes - Operation is normal. No - Check the engine starter harness connections. 3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions: NOTE: Each test must be completed within 30 seconds after the engine starts. After each test the ignition key must be cycled, or the driver s door must be opened and closed. - Move the shift lever out of the P position. - Unlock or open the doors or the tailgate. - Open the hood. - Insert the key in the ignition. - Press on the brake pedal. Does the engine stop after each of these tests? STOP BUTTON TRANSMITTER DISPLAY COMMAND BUTTON START BUTTON 732904AY Yes - Operation is normal. No - Check the engine starter harness connections. 4. Check that the power windows or the moonroof does not function and the shift lever does not move to any position but the P position when the engine is started with the transmitter. 5. Press the command button on the transmitter twice and check the vehicle condition on the display. 6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away, and when the vehicle is in direct sight. 26 of 27 AII 35843-38422 (0712) 2007 American Honda Motor Co., Inc. All Rights Reserved

How to Program an Additional Transmitter 1. Connect the HDS to the data link connector. 2. Start the HDS and click on the car icon. 3. Input the vehicle s VIN and other required information. 4. Select Honda Systems. 5. Select R/C Engine Starter. 6. Select REGISTER NEW TRANSMITTER. 7. When Ready to program the new transmitter shows, select ENTER. 8. Press and release the Command button. 9. Press and release the Stop button. 10. Perform the function check on both transmitters. NOTE: Only 2 remotes can be stored in the system s memory. 2007 American Honda Motor Co., Inc. All Rights Reserved AII 35843-38422 (0712) 27 of 27