PRODUCT CATALOGUE SOLAR BATTERY SYSTEMS OUTBACK VFXR3048E 4kWp SCALABLE SOLAR PV - HIGH PERFORMANCE HOPPECKE HENRY VERMEULEN Sales & Marketing Director Tel: 010 594 7522 Cell: 072 149 9225 Email: henry@value4life.co.za Web: www.value4life.co.za Address: 31 Tenth Street, Boksburg
OUTBACK VFXR3048E 4KWP SCALABLE SOLAR PV - HIGH PERFORMANCE HOPPECKE 10% - 15% yearly growth Roof space required: 35 m 2 SAVINGS R11435 in year 1* INSTALLATION READY: All you need is an installer POWER PRODUCTION: 20+ years of optimal production 22,5 kw/h daily production 545 kw/h monthly production 6534 kw/h annual production 7,5 kw/h daily battery output @30%DOD expected lifespan of battery: 10-13 years 3470 kg per annum *T s & C s Based on Annual Production of 6534kW/h, Electricity cost of R1,75 per kw/h PACKAGE INCLUDES: INVERTER & CHARGE CONTROLLER: 1 x Outback 3000W / 48V DC 230V AC 50Hz 42A Inv / Charger Grid - 5 year warranty 1 x Outback 80A Charge Controller - 5 year warranty SOLAR PANELS: 24 x Solar Frontier 165W 110V solar panels 25 year linear performance warranty 10 year workmanship warranty MOUNTING GEAR: Full Aluminium & Stainless mounting system for any sloped roof for 24 x 165watt solar panels including all: End Clamps Middle Clamps Roof Hooks 10 year guarantee BATTERIES: 24 x Hoppecke 5OPzS Solar Battery 520Ah 2V Batteries expected lifespan 10-14 years based on 30% DOD - 2 year warranty 1 x Outback Flexnet DC System Monitor - 5 year warranty BATTERY CABINET: 1 x Steel Battery Cabinet BATTERY CABLE: 10 metres of 35mm welding cable 10 metres of 25mm welding cable SOLAR CABLE: 100m of 4mm solar cable negative, 5m of 10mm solar cable negative 100m of 4mm solar cable - positive, 5m of 10mm solar cable positive EARTH CABLE: 50 metres of 6mm 2 silicone wire, green / yellow (earth cable) SOLAR CONNECTORS: 28 x PV-KBT4 female inline connectors ONLY R229 998 excl. 14% VAT 28 x PV-KST4 male inline connectors 2 x sets of parallel connectors DC BREAKER: 1 x Noark 2-Pole 63A Breaker DC FUSES, FUSEHOLDERS PV ARRAY & BATTERIES: 3 x 500V 125A DIN 10x38 fuses (00) 4 x 32A 10x38 fuses 2 x 1-Pole 10x38 fuse holders 1000V DC 2 x size 00 160A 3P Disconnect 125A fuse holder 3 x size 00 80A fuses DC SURGE PROTECTION: 1 x Surge Protector Type-2 130V DC DISTRIBUTION BOARDS: 2 x DB Board Surface Mounts 1x12 AC WIRING: 20 meters of 4mm x 2-core + E Surfix cable AC BREAKERS AND ISOLATORS: 1 x 32A 2-Pole Breaker DIN RAIL 1 x 2P 25A C 6kA DIN MCB 2 metres 1 x 40A 4-Pole modular change-over switch TRUNKING: 8 meters of solid trunking SMART SOLAR MONITORING: 1 x Outback Hub 4 Communication Unit - 5 year warranty 1 x Outback Mate 3 Controller Unit - 5 year warranty INSTALLATION DESIGN: 1 x comprehensive installation manual COMMISSIONING / WARRANTY DOCUMENT: 1 x commissioning document including all product warranties OR MONTHLY INSTALMENT R6623,47pm * DEPOSIT: R12 200 excl. 14% VAT *Prices at assumed interest rate 20%, Term: 60 months, E&OE excluded
sun power V L Series OPzS Vented lead-acid battery for cyclic applications Typical applications: Village power supplies Hybrid systems Peak Shaving/ voltage stabilisation Stations for mobile communications Sustainable tourism Cathodic corrosion protection Pumping systems Similar to the illustration Your benefits: Highest cycle stability during PSoC* operation due to tubular plate design with efficient charge current acceptance Maximum energy efficiency by optimised electrolyte recirculation sun air prepared as standard Maximum compatibility dimensions according to DIN 40736-1 Higher short-circuit safety even during the installation based on HOPPECKE system connectors www.hoppecke.com * Partial State of Charge
Type overview sun power V L Series OPzS Capacities, dimensions and weights Service life in cycles and Depth of Discharge Number of cycles [n] W Series OPzS 9000 8000 7000 6000 5000 4000 3000 2000 1000 0 Fig. A Series OPzS L 4 sun power V L 280-6 sun power V L 910 C 100 /1.85 V Ah 0 10 20 30 40 50 60 70 80 90 W Fig. B Series OPzS L C 50 /1.80 V Ah Depth of discharge [%] C 24 /1.83 V Ah 7 sun power V L 1070-12 sun power V L 2170 C 10 /1.80 V Ah 14 sun power V L 2540-16 sun power V L 2900 Optimal environmental compatibility - closed loop for recovery of materials in an accredited recycling system IEC 60896-11 IEC 61427 HOPPECKE Batterien GmbH & Co. KG Bontkirchener Str. 1 D - 59929 Brilon Tel.: +49 (0) 2963 61-374 Fax: +49 (0) 2963 61-270 E-Mail: info@hoppecke.com www.hoppecke.com W Fig. C Series OPzS L C 8 /1.77 V Ah max. Weight kg C 100, C 50, C 24, C 10 and C 5 = Capacity at 100 h, 50 h, 24 h, 10 h and 5 h discharge ** according to DIN 40736-1 data to be understood as maximum values W max.** Length L mm Fig. D Series OPzS L max.** Width W mm 18 sun power V L 3250-26 sun power V L 4700 max.** Height H mm 4 sun power V L 280 280 265 245 213 182 17.1 105 208 420 A 5 sun power V L 350 350 330 307 266 227 20.7 126 208 420 A 6 sun power V L 420 420 395 370 320 273 24.6 147 208 420 A 5 sun power V L 520 520 490 454 390 345 29.1 126 208 535 A 6 sun power V L 620 620 585 542 468 414 34.1 147 208 535 A 7 sun power V L 730 730 685 634 546 483 39.2 168 208 535 A 6 sun power V L 910 910 860 797 686 590 46.1 147 208 710 A 7 sun power V L 1070 1070 1002 930 801 691 59.1 215 193 710 B 8 sun power V L 1220 1220 1145 1063 915 790 63.1 215 193 710 B 9 sun power V L 1370 1370 1283 1192 1026 887 72.4 215 235 710 B 10 sun power V L 1520 1520 1425 1325 1140 985 76.4 215 235 710 B 11 sun power V L 1670 1670 1572 1459 1256 1086 86.6 215 277 710 B 12 sun power V L 1820 1820 1715 1591 1370 1185 90.6 215 277 710 B 12 sun power V L 2170 2170 2010 1843 1610 1400 110.4 215 277 855 B 14 sun power V L 2540 2540 2349 2163 1881 1632 142.3 215 400 815 C 16 sun power V L 2900 2900 2685 2472 2150 1865 150.9 215 400 815 C 18 sun power V L 3250 3250 3015 2765 2412 2097 179.1 215 490 815 D 20 sun power V L 3610 3610 3350 3072 2680 2330 187.3 215 490 815 D 22 sun power V L 3980 3980 3685 3382 2952 2562 212.5 215 580 815 D 24 sun power V L 4340 4340 4020 3696 3220 2795 221.2 215 580 815 D 26 sun power V L 4700 4700 4355 4004 3488 3028 229.6 215 580 815 D H Fig. 05/2015 EN sun power V L - OPzS All details in this brochure are based on state-of-the-art technology. Our products are subject to constant development. We therefore reserve the right to make changes.
Product Overview SF145-S SF150-S SF155-S SF160-S SF165-S SF170-S haracteristics Next Generation CIS Solar Frontier s SF145 170 module series offers the highest conversion efficiency of any massproduced thin-film module, up to 13.8 %. All modules are RoHS compliant and cadmiumand lead-free. Fewer production steps and raw materials also mean an industry-leading energy payback time of less than one year. SF145 170 modules are shipped in cardboardfree packaging and use recyclable corner pieces. Product & Technology Highlights Highest efficiency mass-production thin-film module, up to 13.8 % World record 19.7 % achieved in laboratory Light Soaking Effect raises output after installation Good low-light behavior High shadow tolerance High temperature stability Based on proprietary R&D since 1978 Cadmium and lead free
I-V Curve Current [A] 2.5 2 1.5 1 0.5 0 0 30 60 90 Voltage [V] 180 0 120 SF145-S SF150-S SF155-S SF160-S SF165-S SF170-S Certificates and Guarantee Front view 1,257 ±2 RoHS compliant 160 140 120 100 80 60 40 20 ISO 9001: 2000 certified All new product classes are subject to immediate certification Product guarantee: 5 years (extended garantee upon request) Power output guarantee: 90 % for 10 years, 80 % for 25 years Module Drawing Power [W] STC Characteristics SF145-S SF150-S SF155-S SF160-S SF165-S SF170-S Nominal power Pmax 145 W 150 W 155 W 160 W 165 W 170 W Module efficiency % 11.8 % 12.2 % 12.6 % 13.0 % 13.4 % 13.8 % Power tolerance +5 W/ 0 W Open circuit voltage Voc 107.0 V 108.0 V 109.0 V 110.0 V 110.0 V 112.0 V Short circuit current Isc 2.20 A 2.20 A 2.20 A 2.20 A 2.20 A 2.20 A Voltage at nominal power Vmpp 81.0 V 81.5 V 82.5 V 84.0 V 85.5 V 87.5 V Current at nominal power Impp 1.80 A 1.85 A 1.88 A 1.91 A 1.93 A 1.95 A Standard Test Conditions (STC): 1,000 W/m 2 irradiance, module temperature 25 C, air mass 1.5. Isc and Voc are ±10 % tolerance of STC rated values. Module output may rise due to the Light Soaking Effect. Subject to simulator measurement uncertainty (using best-in-class AAA solar simulator and applying Solar Frontier preconditioning requirements): +10 %/ -5 %. NOCT Characteristics SF145-S SF150-S SF155-S SF160-S SF165-S SF170-S Nominal power Pmax 108 W 111 W 115 W 119 W 123 W 126 W Open circuit voltage Voc 97.4 V 98.3 V 99.2 V 100.0 V 100.0 V 102.0 V Short circuit current Isc 1.76 A 1.76 A 1.76 A 1.76 A 1.76 A 1.76 A Voltage at nominal power Vmpp 76.0 V 76.4 V 77.4 V 78.8 V 80.2 V 82.1 V Current at nominal power Impp 1.43 A 1.47 A 1.49 A 1.51 A 1.53 A 1.55 A Nominal Operating Cell Temperature Conditions: Module operating temperature at 800 W/m 2 irradiance, air temperature 20 C, wind speed 1 m/s and open circuit condition. 977 ±2 Performance at Low Irradiance Efficiency reduction of maximum power from an irradiance of 1,000 W/m 2 to 200 W/m 2 at 25 C is typically 2.0 %. The standard deviation for the reduction of efficiency is 1.9 %. (548.5) 120 Back view 454.5 454.5 31 ±1 225 372.5 372.5 225 31 ±1 2 X Ø4 2 X Grounding (50) 150 598.5 ±5 465 ±5 Transverse cross section detail 4 X Ø8.5 Mounting holes 65 33.5 86.6 30 13.5 35 4 X Ø6.6 Mounting holes 13.7 ( ) ( + ) 1,200 ±100 2 X Ø4.5 Longitudinal cross section detail Contact Information Solar Frontier Europe Grünwald bei München, Germany Tel: +49 89 92 86 142 0 Solar Frontier Italy Bari, Italy Tel: +39 080 89 66 984 Solar Frontier K.K. (Headquarter) Tokyo, Japan Tel: +81 3 5531 5626 Solar Frontier Middle East Al Khobar, Kingdom of Saudi-Arabia Tel: +966 3882 0260 Solar Frontier Americas Santa Clara, CA, USA Tel: +1 408 916 4150 www.solar-frontier.com www.solar-frontier.eu Solar Frontier Europe GmbH 30 12 35 21.5 934 ±2 21.5 Temperature Characteristics NOCT 47 C Temperature coefficient of Isc α +0.01 %/K Temperature coefficient of Voc β -0.30 %/K Temperature coefficient of Pmax δ -0.31 %/K Mechanical Characteristics Dimensions (L x W x H) Weight Application class (IEC 61730) Fire rating (IEC 61730) Safety class (IEC 61140) 1,257 x 977 x 35 mm (49.5 x 38.5 x 1.4 in.) 20 kg (44.1 lbs) Class A Class C Snow/wind load* 2,400 Pa (IEC 61646) / 1,600 Pa design load (UL 1703) Cell type Front cover Encapsulant Back sheet Frame Edge sealant Junction box Adhesive Output cables (conductor) Cable lengths (symmetrical) Connectors Packing information II CIS glass substrate (cadmium free) Clear tempered glass, 3.2 mm EVA Weatherproof plastic film (color: black & silver) Anodized aluminum alloy (color: black) Butyl rubber Protection rating: IP67 (with bypass diode) Silicone 2.5 mm2 / AWG14 (halogen free) 1,200 mm (47.2 in.) MC4 compatible 25 modules/pallet 36 pallets/40 container (900 modules) * UL: 1.5 x design load is applied to the module, i.e. 2,400 Pa (50.1 lbs/ft 2 ) is applied to meet the 1,600 Pa UL design load standard. This preliminary data sheet is provided to assist you in evaluating this product that is under development. Solar Frontier reserves the right, at its sole discretion, to change, modify, add or delete portions of the content at any time without notice. POS1-38-PEE42
OPTICS RE Web-Based System Monitoring and Control Platform It s a powerful advantage the ability to see the electricity you produce and consume. To monitor and control your renewable energy system with the touch of a button from any internet connected device anywhere in the world. Real-time status and hands-on control of your power flow and energy storage. Track individual system performance or manage a network of dispersed systems. OPTICS RE from OutBack Power. Product Highlights: Accessible From Any Internet-Connected Device Simple, Intuitive User Interface Can Be Configured to Meet Needs of Individual Users Real-Time Energy Use Data Helps to Save Money OutBack OPTICS RE Features: See your energy use and production Access your system from any internet connected device Remote control access of your system Easily verify system performance and health Smart grid ready Simple insight into complex data via historical graphs Notifications and alerts sent via email Protect your solar energy investment Save up to 30% on energy bills Stay connected with your green lifestyle 36 Communications
MATE3 Advanced System Display and Communications OPTICS RE Compatible The MATE3 advanced system display and communications make it easier than ever to program and monitor a complete OutBack Power system. An intuitive user interface and integrated system configuration wizard make system setup and programming quick and seamless. The ability to set unique multi-level user passwords makes it possible to secure critical system settings from unintended changes while still allowing open access to necessary functions. Other features making system management simpler include an easy-to-read graphical backlit LCD display, improved tactile buttons, and user programmable favorite keys for immediate access to the most wanted features. An intuitive scroll wheel interface allows easy adjustment of system set points. Expandable SD card memory increases data-logging capacity as well as making it easy to upgrade units in the field. A built-in clock and calendar function enables timer-based programming of inverter and charger operation. This setting allows the system to work with time-of-day power rates or to limit a generator s runtime to a specific time period of the day or week. All settings are stored in onboard memory to eliminate the need to reprogram in the event of a system shutdown or battery replacement. The MATE3 supports web-server access via an intranet to allow monitoring of an OutBack system. Product Highlights: Program, Manage and Monitor Entire System Intuitive Menu Structure with Easy-to-Read Graphical Display System Configuration Wizard Up to One Year of Data Logging Model: Display Quick System Access Status Indicators Navigational Controls Setpoint Adjustment Communication Protocol Interconnect Cabling Included PC Computer Interface Field Update Capability Microprocessor Set Point and Data Memory Clock/Calendar MATE3 4.0 x 1.2 full graphical display 5 system operation hot keys, 4 user programmable soft keys (9) LED indicators Operating Temperature Range 0 to 50 C Mounting 5 navigational keys Touch sensitive scroll wheel Proprietary OutBack communications protocol Standard CAT5 network cable with RJ-45 modular jack - 6 (2m) included HTML system status dashboard over local intranet connection Yes (includes Radian Series inverter/chargers, FLEXmax Series charge controllers [rev 3.0 or higher] and FLEXmax Extreme charge controller) 80MHz 32 bit processor 8Mb RAM/ 64Mb of flash RAM Environmental Rating Indoor Type 1 (IP 30) Maximum Cable Length Optional Accessories Warranty Weight (lb/kg) Dimensions H x W x D (in/cm) On-board real time clock with battery backup Surface-mount (various brackets available) 300 (100m) MATE3 USB card Standard 5 year Warranty Unit: 1.4 / 0.64 Shipping: 3.0 / 1.36 Unit: 7.1 x 7.5 x 1.6 / 18 x 19 x 4.1 Shipping: 3.25 x 9 x 13.5 / 8.26 x 22.9 x 34.3 Communications 37
HUB4 & HUB10.3 System Communications Manager HUB System Communications Manager The HUB system communications manager components form the backbone of a networked OutBack power conversion system. The OutBack HUB communicates stacking, load share and power save off/on signals. Interconnection cabling is standard Ethernet CAT5 with RJ-45 modular jacks. Through a HUB, a system is completely coordinated and managed by the MATE advanced system display and communications. Models: HUB4 HUB10.3 Number of Ports 4 plus MATE 10 plus MATE Operating Temperature Range 0 to 50 C 0 to 50 C Three-phase/Sub-Phase Master Stacking No Yes Warranty Standard 5 year Standard 5 year Weight (lb/kg) Unit: 1 / 0.5 Shipping: 3 / 1.4 Unit: 1 / 0.5 Shipping: 3 / 1.4 Dimensions H x W x L (in/cm) Unit: 10.5 x 6.25 x 1.27 / 27 x 16 x 3 Shipping: 12 x 6 x 5 / 31 x 15 x 13 Unit: 10.5 x 6.25 x 1.27 / 27 x 16 x 3 Shipping: 12 x 6 x 5 / 31 x 15 x 13 HUB4 Stacking Diagram 4 3 2 1 HUB10.3 Stacking Diagram 10 9 8 7 6 5 4 3 2 1 or 40 Communications
SOLAR MOUNTING SYSTEMS MANUFACTURED FROM QUALITY ALUMINIUM OUR PRODUCTS ARE READILY AVAILBLE TILE ROOF With Rafter anchor plate WE SUPPLY FOR RESIDENTIAL AND COMMERCIAL HIGH QUALITY ALUMINIUM SYSTEMS ALUMINIUM SYSTEMS A TRUSTED PRODUCT OF SOUTH AFRICA IBR - Penetrating
WE OFFER A SOLUTION FOR ALL ROOF PROFILES A-FRAME Tilting onto concrete roof, with rear wind deflectors and concrete ballasts, non-penetrating SLATE ROOF - Penetrating KITS INCLUDE ALL COMPONENTS REQUIRED STANDING SEAM NO SPECIAL TOOLING REQUIRED A-FRAME Tilting with clamps for IBR/CORRUGATED etc EASY INSTALLATION KLIP-lOK OR SAFLOK700 - non-penetrating GROUND MOUNT