install guide Document number 07 Revision Date 050 firmware ADS-AL(RS)-FM6-[ADS-ALCA] hardware ADS-ALCA accessories ADS-USB (REQUIRED) COMPATIBLE RF-KIT (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 05 BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
Page of 5 DOC.: #07 050 vehicle List - of FEATURES MODEL YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS X LOCK /STANDALONE MOD. TACHOMETER STATUS HOOD STATUS OUTPUT BRAKE PEDAL STATUS OUTPUT RAP SHUTDOWN CTRL HEATED MIRRORS CTRL HEATED SEATS CTRL REAR DEFROST CTRL NOTES F-50 STD key AT 5 F-50 PTS AT 5 Fusion STD key AT - Fusion Hybrid STD key AT - Fusion PTS AT - Fusion Hybrid PTS AT - MKZ PTS AT - MKZ Hybrid PTS AT - I This firmware does not cover the doorlock feature. Use the OEM remote to control the doorlock feature. The OEM remotes remain functional during runtime. II The maximum runtime for all 0 models is x 0 minutes or x 5 minutes. To perform another remote start sequence, start and stop the vehicle by key or wait hour. LINCOLN FORD MAKE III This firmware does not cover the parklight feature. It's an OEM system feature. See the lane change indicators on the side mirrors of the vehicle for diagnostic codes. Automotive Data Solutions Inc. 05
Page of 5 DOC.: #07 050 BOX CONTENTS - OF BOX CONTENTS WHITE WHITE PIN BLACK CONNECTOR 6 PIN WHITE CONNECTOR MODULE 5 6 5 6 7 WHITE BLUE PROGRAMMING BUTTON 0 PIN BLACK CONNECTOR 7 PIN WHITE CONNECTOR LED A B F C E D 0 9 8 7 6 5 BLACK PIN WHITE CONNECTOR DATA CABLE PIN BLUE CONNECTOR DATA CABLE BLACK DATA PORT (WEBLINK, RF, TELEMATIC) WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc. 05
Page of 5 DOC.: #07 050 COMPATIBLE ESSORIES - OF RF KIT (accessories sold separately) RF KIT 5 AMPS V (+) RED BLACK MODULE DATA PORT DATA CABLE Automotive Data Solutions Inc. 05 RF DECODER ANTENNA
Page 5 of 5 DOC.: #07 050 Automotive Data Solutions Inc. 05 WIRE DESCRIPTION 0 White/Blue 9 White CanH Gray/Orange CanL Purple/Orange V White/Orange (+) Ground 0 /Gray (-) CanH 0 White/Blue CanL 9 White CanH Gray/Orange CanL Purple/Orange V White/Orange (+) Ground 0 /Gray (-) CanH 0 Blue CanL 9 White CanH Gray/Orange CanL Purple/Orange V White/Red (+) Ground 0 /Gray (-) CanH 0 Blue CanL 9 White CanH Gray/Orange CanL Purple/Orange V White/Red (+) Ground 0 /Gray (-) CanH 0 Blue CanL 9 White CanH Gray/Orange CanL Purple/Orange V White/Red (+) Ground 0 /Gray (-) WIRE COLOR CanH CanL CONNECTOR NAME COMPONENT LOCATOR - MODULE LOCATION MKZ / MKZ Hybrid PTS AT - POLARITY LINCOLN Fusion / Fusion Hybrid PTS AT - POSITION Fusion / Fusion Hybrid STD key AT CONNECTOR TYPE 5 FORD F-50 PTS AT 5 CONNECTOR COLOR F-50 STD key AT YEAR MODEL MAKE TYPE - WIRE CHART - OF
Page 6 of 5 DOC.: #07 050 TYPE - WIRING DIAGRAM - OF MODULE MODULE, DRIVER SIDE DASH A B F STEP C E DATA D A B 5 6 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 0 GREEN/RED (NC) 05 BLUE/YELLOW (NC) 06 BLUE/RED (NC) 5 6 7 0 PINK (NC) 0 PINK/BLACK (NC) 0 ORANGE (NC) 0 ORANGE/WHITE (NC) 05 ORANGE/BLACK (NC) 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) 0 WHITE (NC) 0 WHITE/RED (NC) 0 WHITE/BLACK (NC) C D CONNECT TEMPORARILY SEE PROGRAMMING PROCEDURE CANL - 9 CANH - 0 STEP CONNECT TO VEHICLE SEE PROGRAMMING PROCEDURE CANL - CANH - BLACK STEP 0 9 8 7 6 5 0 9 8 7 6 5 SELECT ONE OF THE TWO OPTIONS E 0 0 0 0 BLUE/WHITE (NC) WHITE (NC) BLACK - GROUND RED - V (+) WITHOUT A COMPATIBLE ESSORY: CONNECT V AND GROUND FROM MODULE TO VEHICLE. OR F 5 6 7 8 9 0 DATA CABLE GROUND V (+) GROUND (-) - 0 V (+) - WITH A COMPATIBLE ESSORY: SEE THE COMPATIBLE ESSORIES PAGE FOR DETAILS. 0 GREEN/BLACK (NC) 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) Automotive Data Solutions Inc. 05
MODULE PROGRAMMING PROCEDURE - OF 0 CONNECT every wire shown in STEP and STEP of the wiring diagram. 07 Page 7 of 5 DOC.: #07 050 Set ignition to ON position. 0 Set ignition to ON position. 08 Wait, LED will turn solid RED. 09 Wait, LED will turn solid GREEN for seconds. 0 Set ignition to position. 0 Set ignition to position. 0 Module Programming Procedure completed. 05 Wait, LED will flash GREEN rapidly. 06 DISCONNECT every wire shown in STEP and CONNECT every wire shown in STEP of the wiring diagram. Automotive Data Solutions Inc. 05
VALET MODE PROGRAMMING PROCEDURE - OF NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 0 Time restriction. Complete next step within 7 seconds. 0 Page 8 of 5 DOC.: #07 050 To exit valet mode: repeat steps to 5. Cycle ignition ON five times [5x /ON] rapidly. 0 0 Wait, LED will turn solid RED for seconds. Set ignition to position. 05 Valet Mode Programming Procedure completed. Automotive Data Solutions Inc. 05
aftermarket Remote PRogRamming - OF Page 9 of 5 DOC.: #07 050 aftermarket Remote PRogRamming: notes I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures. Automotive Data Solutions Inc. 05
Page 0 of 5 DOC.: #07 050 MODULE NAVIGATION PROCEDURE - OF It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 Module must be programmed to the vehicle. 05 Use the Module Navigation Chart on the next page. 06 Set ignition to position. 07 TO ESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 TO ESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. 0 0 [X] Automotive Data Solutions Inc. 05
Page of 5 DOC.: #07 050 [Z] settings I Default settings are listed in bold. II Make sure the option is covered on the vehicle before attempting to change the setting. [Y] options module navigation chart: notes [X] menus module navigation chart - OF 0-0 N/A 0 N/A 0 enable 0 DISABLE* 0 N/A 0 DISABLE 0 N/A 0 LOCK + UNLOCK + LOCK 0 LocK + LocK + LocK 0 0 MIN 0 05 MIN 0 0 MIN 0 5 MIN 05 5 MIN** 06 0 MIN** 07 5 MIN** 08 5 min 09- N/A 0 N/A 0 0 N/A 05 TAKEOVER 06 N/A 07 0 FACTORY KEYLESS RS SEQUENCE CONFIGURATION 08 0-07 Technical Support only MODULE RUN TIME N/A *Vehicle will shutdown when a door is opened. **The maximum runtime for 0 models is x 0 minutes or x 5 minutes. Automotive Data Solutions Inc. 05
I II III DURING PROGRAMMING DURING REMOTE WITH IGNITION Automotive Data Solutions Inc. 05 Diagnostic test module LeD status module Diagnostics - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. Page of 5 DOC.: #07 050
MODULE RESET PROCEDURE - OF 0 Disconnect all connectors from module except the BLACK -PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK -PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK -PIN connector. Failure to follow procedure may result with a DTC or a CHECK error message. 0 Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for seconds. 06 Module RESET completed. Automotive Data Solutions Inc. 05 Page of 5 DOC.: #07 050
TAKEOVER PROCEDURE - OF All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote or request switch. 0 Page of 5 DOC.: #07 050 DO NOT PRESS BRAKE PEDAL. Set ignition to ON position. Wait seconds for key validation. 0 Press and release BRAKE pedal. 0 Take over procedure completed. Failure to follow procedure will result in vehicle engine shutdown. Automotive Data Solutions Inc. 05
installation checklist - OF Page 5 of 5 DOC.: #07 050 checklist WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press the LOCK button once [x] on the aftermarket keyfob. 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question : Do the doors lock? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. RAP and auto light shutdown test YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 0 Press the UNLOCK button once [x] on the aftermarket keyfob. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Question : Do the doors unlock? Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the trunk or hatch open/unlock? Question 9: Does the vehicle remote start? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. 5 Enter vehicle and close the doors. Question : Does the driver side sliding door open? 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. YES: Press the AUX button once [x] to close the driver sliding door and go to next step. 7 Wait for the vehicle to start. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press brake pedal. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. YES: Go to next step. 6 YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. Question 0: Does the vehicle shut down? Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 0 Installation checklist completed. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. Automotive Data Solutions Inc. 05