STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades 1 2 3 4 5 Motivia Motorization
Table of Contents Step 1 - Getting Started....3 Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation experience. If you encounter any difficulties or questions, please reach out to us for help. It s why we re here. Call us at 800.248.8888 or visit www.smithandnoble.com/knowhow for more info on installation. Overview - Motorization with No Valance....4 Step 2 - Mounting the s...5 Step 3 - Hanging the Shade...6 Step 4 - Attaching the Power Source.... 7-8 Overview - Motorization with Decorative Cassette/2 on 1 Headrail...9 Step 2 - Mounting the s... 10-11 Step 3 - Attaching the Power Source.... 12 Step 4 - Hanging the Shade... 12 Overview - Motorization with Aluminum Valance... 13 Step 2 - Mounting the s... 14 Step 3 - Hanging the Shade... 15 Step 4 - Attaching the Power Source.... 16 Step 5 - Attaching the Valance.... 17-18 We recommend you hold on to all packaging until your window coverings are fully installed. Should something go wrong (we strongly doubt it), we want any potential returns to be as painless as possible. Operating the Remote Controls.... 19 Remote Control.... 19 Wand Control.... 19 Optional Hold down brackets.... 20 Skew Adjustment.... 20 Care & Cleaning Instructions... 21 Safety... 21 Warranty...Back Cover Customer Service Hours Monday Friday: 6am 7pm PT Saturday Sunday: 7am 4pm PT smithandnoble.com 1 smithandnoble.com 800.248.8888 2
Step 1 Parts & Tools Overview Getting Started First, make sure you have all the parts and tools required to install your shades. Motorization with No Valance - Remote Control ALL THE HARDWARE YOU LL NEED: Pencil, screw-driver, ¼ nut driver, level, and a drill with a 1 16 drill bit. Then find wooden studs where you ll want to attach the brackets; if you need to mount your shades to wallboard or plaster, use a secure fastener designed for hollow wall applications. For metal surfaces, pre-drill holes and use the included screws. For concrete, stone, brick, or tile surfaces, use a masonry drill and appropriate plugs, anchors, or screws. Headrail It s important when selecting a fastener to make sure it s designed to support the weight of the shade. Follow the fastener manufacturer s instruction from there on out. Battery Pack SCREWS SHADE BRACKETS (NO VALANCE) HEADRAIL MOUNT WALL MOUNT BATTERY PACK CLIPS CASSETTE BRACKET Bottom Bar 1 2 3 4 5 EXTENSION BRACKET (OPTIONAL) HOLD DOWN BRACKET (OPTIONAL) ALUMINUM VALANCE BRACKETS REMOTE CONTROL PENCIL & SCREWDRIVER (NOT INCLUDED) POWER DRILL & LEVEL (NOT INCLUDED) 3 smithandnoble.com 800.248.8888 4
Step 2 Mounting s Step 3 Hanging the Shade Inside Mount Shades without Headrail Mount the brackets to the top of the window frame. Make sure the brackets are aligned. Support Nub Once the brackets are secured and level, the fabric roll can be inserted. Make sure your hands are clean to avoid soiling the shade. Idler Post V-Slot Insert the foot of the motor-side bracket into the slotted center hole of the motor end of the shade. The wire should be positioned so that it goes up on an inside mount or back on an outside mount. This will provide easy Outside Mount The installation brackets are always mounted so that the inner surfaces face each other. s must be in line and level. Motor Side Idler Side Foot T-Hook access to the setting key. Set the post of the idler end into the V of the support bracket. Rotate the T-hook on the support bracket to engage over the nub to secure the fabric roll. Extension s (optional) Optional Extension s are used to project the back of the shade up to 2 1 2" from the mounting surface. Attach the Standard Mounting to the Extension with the nut and bolt provided. 2"min. surface required Extension 5 smithandnoble.com 800.248.8888 6
Step 4 Attaching the Power Source Step 4 Attaching the Power Source Attaching the Power Source When attaching the Power Source to the shade, first plug the battery pack wire into the motor wire. (see illustration to right) Noting the length of the wire, determine the best location for the battery pack. The pack may be mounted to the window casing, the wall or behind the fabric roll (if space permits). Before mounting the pack make sure that the pack and excess wire will not interfere with the operation of the shade. Extension wires are available if needed. Battery Pack Attach and twist clockwise until tight (do not overtighten) Battery Wire Motor Wire Attaching the Transformer (optional) Plug the transformer wire into the motor wire. Secure the wire behind the shade and along the window casing as desired. Plug the transformer into an electrical outlet. If the wire is not long enough to reach, optional 48 extension wires are available. Battery Pack Clips - Wall Mounting Wall mount - attach the pack clips with the screws provided. If necessary, remove shade to mount the clips in the desired location. Press the pack into the Clips 7 smithandnoble.com 800.248.8888 8
Overview Step 2 Mounting s Motorization with Decorative Cassette - 2 on 1 Headrail, Remote Control, and Wand Control Decorative Cassette 2" Inside Mount Center the shade in the window frame. Mark the position of the brackets. End brackets should be located 2" in from each end. Mount the brackets to the top of the window frame. Make sure the brackets are aligned. Space additional brackets evenly between two end brackets. Be sure to leave space between brackets for battery pack. 1 2 3 4 5 Bottom Bar Remote Control Side Mount (optional) Measure from window sill up to desired mounting position. Mount Side Mount s on each side of window frame as shown. Make sure to confirm that headrail will sit perfectly level. Once Side Mount s are installed and properly positioned, attach the Standard Mounting s using the nuts and bolts provided. Wand Control 2 on 1 Headrail with Remote Control or Wand Control Shade with Wand Control 9 smithandnoble.com 800.248.8888 10
Step 2 Mounting s Step 3 Attaching the Power Source Outside Mount First, hold the shade above the window so that it s perfectly centered 2" Mounting s Battery Pack Battery Wire Attaching the Power Source When attaching the Power Source to the shade, first plug the battery pack over the window opening at the desired height. Mark the position of the bracket on the wall. End brackets should be located 2" from each end. Mount the brackets to the wall. Make sure the mounting brackets are level. If needed, space additional brackets evenly between two end brackets. Headrail Attach and twist clockwise until tight (do not overtighten) Motor Wire wire into the motor wire. Noting the length of the wire, determine the best location for the battery pack. The pack may be mounted to the window casing, the wall or behind the fabric roll (if space permits). Before mounting the pack make sure that the pack and excess wire will not interfere with the operation of the shade. Extension wires are available if needed. Attaching the Transformer (optional) Extension s (optional) Optional Extension s are used to project the back of the shade up to 2 1 2" from the mounting surface. Attach the Standard Mounting to the Extension with the nut and bolt provided. Extension Plug the transformer wire into the motor wire. Secure the wire behind the shade and along the window casing as desired. Plug the transformer into an electrical outlet. If the wire is not long enough to reach, optional 48 extension wires are available. Step 4 Hanging the Shade Hanging the Shade Battery Pack Mounting Pack Clip Insert the rail into the opening of the bracket. Push the rail back until it is fully engaged. Attach the pack clips to the headrail as pictured. Then press the battery into place. Shade Removing the Shade To remove the shade, partially lower the shade and insert a flat head screwdriver as shown. Twist the screwdriver until the headrail disengages from the bracket. 11 smithandnoble.com 800.248.8888 12
Overview Step 2 Mounting s Motorized with Aluminum Valance - Remote Control Aluminum Valance Inside Mount The brackets can be mounted up against the window frame, or to the back side of the window casing. Make sure the mounting brackets are level. The brackets are always mounted so that the inner surface s face each other. s are mounted with the open end down. Outside Mount Bottom Bar The brackets can be mounted to wall or window frame. Make sure the mounting brackets are level. The brackets are always mounted so that the inner surfaces face each other. s are mounted with the open end down. 1 2 3 4 5 REMOTE CONTROL 13 smithandnoble.com 800.248.8888 14
Step 3 Hanging the Shade Step 4 Attaching the Power Source Hanging the Shade Once the brackets are secured and level, the fabric roll can be inserted. Make sure your hands are clean to avoid soiling the fabric. Support T-Hook Battery Pack Battery Wire Motor Wire Attaching the Power Source Plug the battery pack wire into the motor wire. Noting the length of the wire, determine the best location for the battery pack. Insert the foot of the control side The pack may be mounted to the bracket into the slotted center hole of the clutch. Set nub of the end plug into the V of the support bracket. Rotate Attach and twist clockwise until tight (do not overtighten) window casing, the wall or behind the fabric roll (if space permits). Before mounting the pack make sure that the the T-hook on the support bracket to pack and excess wire will not interfere engage over the nub on the idler and secure the fabric roll. Nub with the operation of the shade. Extension wires are available if needed. Attaching the Transformer (optional) Plug the transformer wire into the motor wire. Secure the wire behind the shade and along the window casing as required. Plug the transformer into an electrical outlet. If the wire is not long enough to reach, optional 48 extension wires are available. Attach Battery Pack Clips Wall mount - attach the pack clips with the screws provided. If necessary, remove shade to mount the clips in the desired location. Press the pack into the Clips 15 smithandnoble.com 800.248.8888 16
Step 5 Attaching the Valance Step 5 Attaching the Valance Attaching the Valance Attach the valance by first hooking the top lip of the valance panel onto the bracket as shown. Swing the bottom of the valance panel towards the bracket and gently press at the bottom of the panel until the lip on the valance engages and snaps lock to the bracket. Valance Cover Peel & Stick Tape Valance Cover - Outside Mount You will be attaching the valance bracket cover to the valance bracket with the peel & stick tape provided is on the back of the brackets. Before you remove the tape backing, line up the bracket cover in the correct position to ensure proper fit. After you have determined the correct position of the bracket cover, peel off the tape backing and simply press the it onto the end of the bracket. See illustration to left. 17 smithandnoble.com 800.248.8888 18
Operating the Remote Controls Optional Remote Control Hold Down Select the desired channel with the CHANNEL key. The channel indicator light will illuminate the channel that is on. If all 5 lights are lit, the remote will control all 5 channels at once. Tapping the UP or DOWN keys for less than 2 seconds will move the shade in short steps. Holding the UP or DOWN keys down for more than 2 seconds before releasing, will operate the shade in the faster standard speed. 1 2 3 4 5 Channel Display Up Stop Down Channel + Channel Optional Hold Down s are mounted with the supplied screws. With the shade at its proper drop, place the pin of each Hold Down into the hole in each End Cap and make sure the pins are level and aligned. Raise the shade, then screw the Hold Down into the mounting surface. Skew Adjustment Press the UP or DOWN keys to raise or lower the shade. Press the STOP key to stop the shade anywhere along the window. Refer to the Motorization Guide for additional details. Wand Controls Touch & Go Feature: To fully raise or lower the shade, simply press the UP or DOWN button for 2 seconds and release. The shade will automatically stop when it reaches the upper or lower limit. (See the Motorization Guide if the upper or lower limits are not set at the desired positions) Tapping the UP or DOWN keys for less than 2 seconds will move the shade in short steps. Holding the UP or DOWN keys down for more than 2 seconds before releasing, will operate the shade in the faster standard speed. Up Down Fabric Roll Place tape at this end If the shade does not raise evenly, first make sure the mounting brackets are mounted level with each other. If the shade is level and it still skews, operate the shade to the full down position. Prepare a strip of masking tape approximately 5 long. On the side of the shade opposite of the skewing direction, and as close to the end of the roller as possible, lift the fabric toward the back of the shade using your fingers and slide the tape with the sticky side facing the roller up as far as possible. The tape is to be running parallel to the roller. Roll the shade up and check for skewing. If the shade is still skewing, add another strip of tape on top of the first one. If the shade is now skewing in the opposite direction, tear off about 1 of tape from the last strip installed. The tape is to be torn from the end closest to the center of the shade. Press the DOWN or UP button to lower or raise the shade. Press the opposite button to stop the shade at the desired position. If these suggestions don t work, then please give us a call or visit our website. Refer to the Motorization Guide for additional details. 19 smithandnoble.com 800.248.8888 20
Care & Cleaning /Safety Troubleshooting Care & Cleaning Occasional light vacuuming with a soft bristle attachment or gentle feather dusting is all that is required to keep your shades looking fresh and neat. PROBLEM The motor does not work The motor continues to run in one direction SOLUTION 1. Check that the power source and motor are connected properly. 2. Confirm the batteries are fresh. The limit setting was unsuccessful and needs to be reset. Safety First. Style Second To None. Great style should never come at the cost of safety. Every Smith & Noble window treatment conforms strictly to today s safety standards, including permanent tie-down devices and built-in cord stops. To protect young children and pets, there s no better way to eliminate risk than to use one of our cordless products. Child Safety The indicator light on the remote does not shine or the remote-controlling range becomes shorter. The motor stops working or works intermittently Replace the battery in the remote (CR2430 Lithium) Replace the batteries in the wand with 8 fresh AA alkaline batteries. If these suggestions don t work, then please give us a call or visit our website. 21 smithandnoble.com 800.248.8888 22
Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship. Shades or blinds must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. In need of warranty service? Call us at 800.248.8888 and we ll arrange for a repair or replacement ASAP. 2015 Smith & Noble Home, Inc. All Rights Reserved SN0116
STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades Cordless Control with Mounting Bar or Cordless Control with Cassette
Table of Contents Step 1 - Getting Started.... 3 Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation experience. If you encounter any difficulties or questions, please reach out to us for help. It s why we re here. Call us at 800.248.8888 or visit www.smithandnoble.com/knowhow for more info on installation. We recommend you hold on to all packaging until your window coverings are fully installed. Should something go wrong (we strongly doubt it), we want any potential returns to be painless as possible. Customer Service Hours Monday Friday: 6am 7pm PT Saturday Sunday: 7am 4pm PT smithandnoble.com Overview - Cordless Control with Mounting Bar.... 4 Step 2 - Mounting the s....5-6 Step 3 - Hanging and Removing the Shade.... 7 Step 4 - Operating the Shade.... 8 Optional - Attaching Cordless Handle.... 8 Hold Down s.... 9 Upstop Adjustment... 9 Tension Adjustment.... 10 Skew Adjustment... 10 Overview - Cordless Control with Decorative Cassette...11 Step 2 - Mounting the s.... 12-13 Step 3 - Hanging and Removing the Shade.... 14 Step 4 - Operating the Shade.... 15 Optional - Attaching Cordless Handle.... 15 Hold Down s.... 16 Upstop Adjustment... 16 Tension Adjustment.... 17 Skew Adjustment... 17 Care & Cleaning... 18 Safety... 18 Warranty... 19 1 smithandnoble.com 800.248.8888 2
Step 1 Parts & Tools Overview Getting Started First, make sure you have all the parts and tools required to install your shades. Cordless Control With Mounting Bar ALL THE HARDWARE YOU LL NEED: Pencil, screw-driver, ¼ nut driver, level, and a drill with a 1 16" drill bit. Mounting Bar Then find wooden studs where you ll want to attach the brackets; if you need to mount your shades to wallboard or plaster, use a secure fastener designed for hollow wall applications. For metal surfaces, pre-drill holes and use the included screws. For concrete, stone, brick, or tile surfaces, use a masonry drill and appropriate plugs, anchors, or screws. It s important when selecting a fastener to make sure it s designed to support the weight of the shade. Follow the fastener manufacturer s instruction from there on out. Bottom Bar SCREWS MOUNTING BAR BRACKET CASSETTE BRACKET POWER DRILL (NOT INCLUDED) SCREWDRIVER (NOT INCLUDED) CORDLESS HANDLE (OPTIONAL) HOLD DOWN BRACKET (OPTIONAL) EXTENSION BRACKET (OPTIONAL) PENCIL (NOT INCLUDED) LEVEL (NOT INCLUDED) BRACKET QTY SHADE WIDTH 2 up to 40" 3 40" 72" 4 721/8" 84" 5 84" 114" 3 smithandnoble.com 800.248.8888 4
Step 2 Mounting s Step 2 Mounting s (con't) Inside Mount 2" Plastic Tab faces up Outside Mount Center the shade in the window First, hold the shade above the frame. Mark the position of the brackets. End brackets should be Plastic Tab faces back window so that it s perfectly centered over the window opening at the located 2" in from each end. Mount desired height. Mark the position of the brackets to the top of the window the headrail on the wall. End brackets frame. Make sure the brackets are should be located 2" from each end. aligned. Space additional brackets Mount the brackets to the wall. Make evenly between two end brackets. sure the mounting brackets are level. If needed, space additional brackets evenly between two end brackets. Side Mount (optional) Measure from window sill up to desired mounting position. Mount Extension s on each side of window frame as shown. Make sure to confirm that headrail will sit perfectly level. Once Extension s are installed Plastic Tab faces back Mounting Extension Plastic Tab faces back Extension s (optional) Optional Extension s are used to project the back of the shade up to 2 1 2" from the mounting surface. Attach the Standard Mounting to the Extension with the nut and bolt provided. and properly positioned, attach the Standard Mounting s using the nuts and bolts provided. 5 smithandnoble.com 800.248.8888 6
Step 3 Hanging the Shade Step 4 Operating the Shade Hanging the Shade Cordless Control (Inside Mount or Extension ) Hook the rail onto the front of the bracket and rotate it until the back of the rail securely snaps into place. Headrail Opening and closing your new Smith & Noble shades is entirely hasslefree. To lower it, pull down gently on the bottom bar. Your shade will slowly raise automatically with a slight pull on the bottom bar. Simply pull down slightly, release and the shade will (Outside Mount) raise effortlessly. Hook the rail onto the bottom of the bracket and rotate it until the back of the rail securely snaps into place. Bottom Bar Removing the Shade (Inside Mount) To remove the shade, partially lower the shading and press the clear tab on the mounting bracket. Rotate the shade to remove. (Outside Mount) Press down on clear tab and then rotate shade to release. (Optional) Attach Cordless Handle (optional) Attach the optional clear Cordless Handle in order to protect and keep your shades clean. If you decide to attach the handle and adjust the upstop, make sure the handle does not touch the fabric roll when the shade is fully raised or it could damage the fabric. Cordless Handle 7 smithandnoble.com 800.248.8888 8
(Optional) (Optional) Hold Down Optional Hold Down s are Tension Adjustment mounted with the supplied screws. With the shade at its proper drop, place the pin of each Hold Down into the hole in each End Cap and make sure the pins are level and aligned. Mark the screw holes with a pencil. Raise the shade, then screw the Hold Down into the mounting surface. Hold Down Decrease Tension Increase Tension If the shade does not retract fully, you may need to increase the tension by using a screwdriver. When facing the shade, on a STANDARD ROLL the adjustment is made at the LEFT end of the shade. On a REVERSE ROLL the adjustment is made at the RIGHT end of the shade. Upstop Adjustment Skew Adjustment Retract the shade and let it stop at the top. If you do not like where the upstop is set it can be adjusted by using a screwdriver. When facing the shade, on a STANDARD ROLL the adjustment is made at the RIGHT end of the shade. On a REVERSE ROLL the adjustment is made at the LEFT end of the shade. If the shade does not raise evenly, first make sure the mounting brackets are mounted level with each other. Be sure your shade is fully raised before making adjustments. Raise Bottom Rail Highest allowed position of bottom rail pictured Lower Bottom Rail Bottom rail is too high. Fabric may be damaged Tape Fabric Roll If the shade is still not level, pull the shade all the way down. Prepare a strip of masking tape approximately 5 long. On the side of the shade opposite of the skewing direction, and as close to the end of the roller as possible, lift the fabric toward the back of the shade using your fingers and slide the tape with the sticky side facing the roller up as far as possible. The tape is to be running parallel to the roller. Roll the shade up and check for skewing. If the shade is still skewing, add another strip of tape on top of the first one. If the shade is now skewing to WARNING: When setting the upstop, do not allow the bottom rail to jam between the fabric roll and the mounting bar. This will result in damage to the fabric. Correct Incorrect the opposite direction, tear off about 1" of tape from the last strip installed. The tape is to be torn from the end closest to the center of the shade. If these suggestions don t work, then please give us a call or visit our website. 9 smithandnoble.com 800.248.8888 10
Overview Step 2 Mounting s Cordless Control with Decorative Cassette Decorative Cassette 2" Inside Mount Center the shade in the window frame. Mark the position of the headrail. End brackets should be located 2" in from each end. Mount the brackets to the top of the window frame. Make sure the brackets are aligned. Space additional brackets evenly between two end brackets. Bottom Bar Side Mount (optional) Measure from window sill up to desired mounting position. Mount Side Mount s on each side of window frame as shown. Make sure to confirm that headrail will sit perfectly level. Once Side Mount s are installed and properly positioned, attach the Standard CORDLESS HANDLE (OPTIONAL) HOLD DOWN BRACKET (OPTIONAL) EXTENSION BRACKET (OPTIONAL) Mounting s using the nuts and bolts provided. BRACKET QTY SHADE WIDTH 2 up to 40" 3 40" 72" 4 721/8" 84" 5 84" 114" 11 smithandnoble.com 800.248.8888 12
Step 2 Mounting s (con't) Step 3 Hanging the Shade Outside Mount First, hold the shade above the window so that it s perfectly centered over the window opening at the desired height. Mark the position of the headrail on the wall. s should be located 2" from each end. Mount the brackets to the wall. Make sure the mounting brackets are level. If needed, space additional brackets evenly between two end brackets. Hanging the Shade Insert the rail into the opening of the bracket. Push the rail back until it is fully engaged. Removing the Shade Extension s (optional) Optional Extension s are used to project the back of the shade up to 2 1 2" from the mounting surface. Attach the Standard Mounting to the Extension with the nut and bolt provided. Extension To remove the shade, partially lower the shade and insert a flat head screwdriver as shown. Twist the screwdriver until the headrail disengages from the bracket. 13 smithandnoble.com 800.248.8888 14
Step 4 Operating the Shade (Optional) Cordless Control Opening and closing your new Smith & Noble shades is entirely hassle-free. To lower it, pull down gently on the bottom bar. Your shade will slowly raise automatically with a slight pull on the bottom bar. Simply pull down slightly, release and the shade will raise effortlessly. Hold Down Hold Down Optional Hold Down s are mounted with the supplied screws. With the shade at its proper drop, place the pin of each Hold Down into the hole in each End Cap and make sure the pins are level and aligned. Mark the screw holes with a pencil. Raise the shade, then screw the Hold Down into the mounting surface. Upstop Adjustment (Optional) Bottom Bar Retract the shade and let it stop at the top. If you do not like where the upstop is set it can be adjusted by using a screwdriver. Attach Cordless Handle (optional) Attach the optional clear Cordless Handle in order to protect and keep your shades clean. If you decide to attach the handle and adjust the upstop, make sure the handle does not touch the fabric roll when the shade is fully raised or it could damage the fabric. Cordless Handle When facing the shade, on a STANDARD ROLL the adjustment is made at the RIGHT end of the shade. On a REVERSE ROLL the adjustment is made at the LEFT end of the shade. If the shade does not raise evenly, first make sure the mounting brackets are mounted level with each other. Be sure your shade is fully raised before making adjustments. WARNING: When setting the upstop, do not allow the bottom rail to jam between the fabric roll and the top of the cassette. This will result in damage to the fabric. 15 smithandnoble.com 800.248.8888 16
(Optional) Troubleshooting Tension Adjustment If the shade does not retract fully, you may need to increase the tension by PROBLEM The shade fabric does not roll up evenly SOLUTION Make sure the mounting brackets are aligned and level with one another. using a screwdriver. When facing the shade, On a The shade will not raise The shade tension may need to be increased, see tension adjustment. STANDARD ROLL the adjustment is made at the LEFT end of the shade. On a REVERSE ROLL the adjustment is made at Decrease Tension Increase Tension If these suggestions don t work, then please give us a call or visit our website. the RIGHT end of the shade. Skew Adjustment Care & Cleaning /Safety If the shade is still not level, pull the shade all the way down. Prepare a strip of masking tape approximately 5 long. On the side of the shade opposite of the skewing direction, and as close to Tape Fabric Roll Care & Cleaning Occasional light vacuuming with a soft bristle attachment or gentle feather dusting is all that is required to keep your shades looking fresh and neat. the end of the roller as possible, lift the fabric toward the back of the shade using your fingers and slide the tape Safety First. Style Second To None. with the sticky side facing the roller up as far as possible. The tape is to be running parallel to the roller. Great style should never come at the cost of safety. Every Smith & Noble window treatment conforms strictly to today s safety standards, including permanent tie-down devices and built-in cord stops. To protect young children and pets, there s no better way to eliminate Roll the shade up and check for risk than to use one of our cordless products. skewing. If the shade is still skewing, add another strip of tape on top of the Child Safety first one. If the shade is now skewing to the opposite direction, tear off about 1" of tape from the last strip installed. The tape is to be torn from the end closest to the center of the shade. If these suggestions don t work, then please give us a call or visit our website. 17 smithandnoble.com 800.248.8888 18
Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship. Shades or blinds must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. In need of warranty service? Call us at 800.248.8888 and we ll arrange for a repair or replacement ASAP. 2016 Smith & Noble Home, Inc. All Rights Reserved SN0216
STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades Loop Control, Loop Control with Cassette/2 on 1 Headrail, & Loop Control with Aluminum Valance
Table of Contents Step 1 - Getting Started....3 Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation experience. If you encounter any difficulties or questions, please reach out to us for help. It s why we re here. Call us at 800.248.8888 or visit www.smithandnoble.com/knowhow for more info on installation. We recommend you hold on to all packaging until your window coverings are fully installed. Should something go wrong (we strongly doubt it), we want any potential returns to be as painless as possible. Customer Service Hours Monday Friday: 6am 7pm PT Saturday Sunday: 7am 4pm PT Overview - Loop Control....4 Step 2 - Mounting the s... 5-6 Step 3 - Hanging the Shade...7 Step 4 - Installing Cord Tensioner...7 Step 5 - Operating the Shade....8 Overview - Loop Control with Decorative Cassette/2 on 1 Headrail...9 Step 2 - Mounting the s... 10-11 Step 3 - Hanging the Shade... 11 Removing the Shade.... 12 Step 4 - Installing Cord Tensioner... 12 Step 5 - Operating the Shade.... 12 Overview - Loop Control with Aluminum Valance.... 13 Step 2 - Mounting the s... 14 Step 3 - Hanging the Shade... 15 Step 4 - Attaching the Valance.... 15-16 Step 5 - Installing Cord Tensioner... 16 Step 6 - Operating the Shade... 17 Optional Skew Adjustment.... 17 Hold Down s... 18 Troubleshooting.... 18 Care & Cleaning Instructions.... 18 Safety... 18 Warranty...Back Cover smithandnoble.com 1 smithandnoble.com 800.248.8888 2
Step 1 Parts & Tools Overview Getting Started Loop Control No Cassette or Valance First, make sure you have all the parts and tools required to install your shades. ALL THE HARDWARE YOU LL NEED: Pencil, screw-driver, ¼ nut driver, level, and a drill with a 1 16 drill bit. Then find wooden studs where you ll want to attach the brackets; if you need to mount your shades to wallboard or plaster, use a secure fastener designed for hollow wall applications. For metal surfaces, pre-drill holes and use the included screws. For concrete, stone, brick, or tile surfaces, use a masonry drill and appropriate plugs, anchors, or screws. It s important when selecting a fastener to make sure it s designed to support the weight of the shade. Follow the fastener manufacturer s instruction from there on out. Cord Tensioner SCREWS SHADE BRACKETS (NO VALANCE) Bottom Bar CASSETTE BRACKET ALUMINUM VALANCE BRACKETS PENCIL & SCREWDRIVER (NOT INCLUDED) POWER DRILL & LEVEL (NOT INCLUDED) EXTENSION BRACKET (OPTIONAL) HOLD DOWN BRACKET (OPTIONAL) 3 smithandnoble.com 800.248.8888 4
Step 2 Mounting s Step 2 Mounting s Inside Mount Center the shade in the window frame. Mark the position of the brackets. Mount the brackets to the top of the window frame. Make sure the brackets are aligned. s may be mounted on both top and side. Outside Mount First, hold the shade above the window so that it s perfectly centered over the window opening at the desired height. Mark the position of the brackets on the wall. Mount the brackets to the wall. Make sure the mounting brackets are level. 2"min. surface required Extension Extension s (optional) Optional Extension s are used to project the back of the shade up to 2 1 2" from the mounting surface. Attach the Standard Mounting to the Extension with the nut and bolt provided. 5 smithandnoble.com 800.248.8888 6
Step 3 Hanging the Shade Step 5 Operating the Shade Hanging Shades without Headrail Support Loop Control Once the brackets are secured and level, the fabric roll can be inserted. Make sure your hands are clean to avoid soiling the shade. Hold the shade with the bottom of the clutch facing the floor, and the beaded cord hanging straight down. Insert the foot of the control side bracket into the slotted center hole of the clutch. Set nub of the end plug into the V of the support bracket. Rotate Idler Post Support Side Nub V-Slot Clutch T-Hook Control Side Foot Control Side Rear Bead Chain Front Bead Chain Opening and closing your new Smith & Noble shades is entirely hassle-free. Using the loop control, pull the rear bead chain to lower the shade and, pull the front bead chain to raise. the T-hook on the support bracket to engage over the nub to secure the fabric roll. Foot Step 4 Installing Cord Tensioner Installing Cord Tension Your window shade has arrived with a cord tensioner to comply with current child safety standards. The cord tensioner must be mounted and secured before the window shade will operate correctly. To position the tensioner, grasp the screw hole and pull down to release the lock. Pull the cord through the tensioner until the tensioner is at the bottom of the cord loop. Please see cord tensioner guide on how to install (included separately). 7 smithandnoble.com 800.248.8888 8
Overview Step 2 Mounting s Loop Control with Decorative Cassette/2 on 1 Headrail Decorative Cassette 2" Inside Mount Center the shade in the window frame. Mark the position of the brackets. End brackets should be located 2" in from each end. Mount the brackets to the top of the window frame. Make sure the brackets are aligned. Space additional brackets evenly between two end brackets. Cord Tensioner Bottom Bar Extension Mounting Side Mount (optional) Measure from window sill up to desired mounting position. Mount Extension s on each side of window frame as shown. Make sure to confirm that headrail will sit perfectly level. Once Extension s are installed and properly positioned, attach the Standard Mounting s using the nuts and bolts provided. 2 on 1 Headrail with Loop Control 9 smithandnoble.com 800.248.8888 10
Step 2 Mounting s Outside Mount First, hold the shade above the window so that it s perfectly centered 2" Mounting s Removing the Shade To remove the shade, partially lower the shade and insert a flat head screwdriver over the window opening at the desired height. Mark the position of Headrail as shown. Twist the screwdriver until the headrail disengages from the bracket. the bracket on the wall. End brackets should be located 2" from each end. Mount the brackets to the wall. Make Step 4 Installing Cord Tensioner sure the mounting brackets are level. If needed, space additional brackets Installing Cord Tensioner evenly between two end brackets. Your window shade has arrived with a cord tensioner to comply with current child safety standards. The cord tensioner MUST be mounted and secured before the window shade will operate correctly. To position the tensioner, grasp the screw hole and pull down to release the lock. Pull the cord through the tensioner until the tensioner is at the bottom of the Extension s (optional) Optional Extension s are used to project the back of the shade up Extension cord loop. Please see cord tensioner guide on how to install (included separately). to 2 1 2" from the mounting surface. Attach the Standard Mounting Step 5 Operating your Shade to the Extension with the nut and bolt provided. Operating your Shade Step 3 Hanging the Shade Rear Bead Chain Front Bead Chain Opening and closing your new Smith & Noble shades is entirely hasslefree. Using the loop control, pull the rear bead chain to lower the shade Hanging the Shade and the front bead chain to raise. Insert the rail into the opening of the bracket. Push the rail back until it is fully engaged. 11 smithandnoble.com 800.248.8888 12
Overview Step 2 Mounting s Loop Control with Aluminum Valance Aluminum Valance Inside Mount The brackets can be mounted up against the window frame, or against the side of the window casing. Make sure the mounting brackets are level. The brackets are always mounted so that the inner surfaces face each other. s are mounted with the open end down. Outside Mount Cord Tensioner Mount to wall or window frame. Make sure the mounting brackets are level. The brackets are always mounted so that the inner surfaces face each other. s are mounted with the open end down. Bottom Bar Extension Mounting Extension (Optional) Extension s are used to project the shade out from the mounting surface. This will allow the shade to avoid window cranks and door knobs when raised and lowered. Attach the extension brackets to the wall with the screws provided (or appropriate fasteners for your mounting surface) making sure they are aligned. Attach the mounting brackets to the extension brackets with the bolts and nuts provided. The bracket with the metal post is the control bracket and should be mounted in the same position as ordered, either left or right. The space between the brackets when mounted should be the width of the aluminum valance. 13 smithandnoble.com 800.248.8888 14
Step 3 Hanging the Shade Step 4 Attaching the Valance Hanging the Shade Once the brackets are secured and level, the fabric roll can be inserted. Make sure your hands are clean to avoid soiling the fabric. Insert the foot of the control side bracket into the slotted center hole of the clutch. Set nub of the end plug into the V of the support bracket. Rotate Support T-Hook Valance Cover Peel & Stick Tape Valance Cover - Outside Mount You will be attaching the valance bracket cover to the valance bracket with the peel & stick tape provided is on the back of the brackets. Before you remove the tape backing, line up the bracket cover in the correct position to ensure proper fit. the T-hook on the support bracket to engage over the nub on the idler and secure the fabric roll. Nub After you have determined the correct position of the bracket cover, peel off the tape backing and simply press it onto the end of the bracket. Clutch Control Side See illustration to left. Step 5 Installing Cord Tensioner Step 4 Attaching the Valance Attaching the Valance Attach the valance by first hooking the top lip of the valance panel onto the bracket as shown. Swing the bottom of the valance panel towards the bracket and gently press at the bottom of the panel until the lip on the valance engages and snaps lock to the bracket. Foot Installing Cord Tensioner Your window shade has arrived with a cord tensioner to comply with current child safety standards. The cord tensioner MUST be mounted and secured before the window shade will operate correctly. To position the tensioner, grasp the screw hole and pull down to release the lock. Pull the cord through the tensioner until the tensioner is at the bottom of the cord loop. Please see cord tensioner guide on how to install (included separately). 15 smithandnoble.com 800.248.8888 16
Step 5 Operating your Shade Optional Operating your Shade Hold Down Opening and closing your new Smith & Noble shades is entirely hasslefree. Using the loop control, pull the rear bead chain to lower the shade and, the front bead chain to raise. Rear Bead Chain Front Bead Chain Hold Down Optional Hold Down s are mounted with the supplied screws. With the shade at its proper drop, place the pin of each Hold Down into the hole in each End Cap and make sure the pins are level and aligned. Raise the shade, then screw the Hold Down into the mounting surface. Optional Troubleshooting Skew Adjustment If the shade does not raise evenly, first make sure the mounting brackets are mounted level with each other. If the shade is level and it still skews, operate the shade to the full down position. Prepare a strip of masking tape approximately 5 long. On the side of the shade opposite of the skewing direction, and as close to the end of the roller as possible, lift the fabric toward the back of the shade using your fingers and slide the tape with the sticky side facing the roller up as far as possible. The tape is to be running parallel to the roller. Roll the shade up and check for skewing. If the shade is still skewing, add another strip of tape on top of the first one. If the shade is now skewing in the opposite direction, tear off about 1 of tape from the last strip installed. The tape is to be torn from the end closest to the center of the shade. If these suggestions don t work, then please give us a call or visit our website. Fabric Roll Place tape at this end PROBLEM SOLUTION Make sure the mounting brackets are The shade fabric does not roll up evenly aligned and level with one another. The shade may be caught on an obstruction The shade will not raise such as a window crank or latch; if this is the case feel free to untangle. If these suggestions don t work, then please give us a call or visit our website. Care & Cleaning Care & Cleaning /Safety Use brush or dust head attachment. Occasional light vacuuming with a soft bristle attachment or gentle feather dusting is all that is required to keep your shades looking fresh and neat. Safety First. Style Second To None. Great style should never come at the cost of safety. Every Smith & Noble window treatment conforms strictly to today s safety standards, including permanent tiedown devices and built-in cord stops. To protect young children and pets, Loop Control works with a cord tensioner, which must be mounted to your window frame or wall. The shade or blind will not work if the cord tensioner is not mounted. Child Safety 17 smithandnoble.com 800.248.8888 18
Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship. Shades or blinds must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. In need of warranty service? Call us at 800.248.8888 and we ll arrange for a repair or replacement ASAP. 2016 Smith & Noble Home, Inc. All Rights Reserved SN0216