Grove YB5515-2 Product Guide ASME B3.5 Imperial 85%, Metric 85%, DIN/ISO Features 13,6 t (15 USt) capacity 12,5 m (41 ft) three-section, full-power synchronized boom 9,1 t (1 USt) deck carrying capacity Load sensing piston pump with hydraulic proportional controls
Features The reach and capacity to get the job done The standard three-section boom offers 4,6 m 12,5 m (15 ft 41 ft) of reach with a max tip height of 14,2 m (46.5 ft). The optional foursection boom offers 5,4 m 15,4 m (17.8 ft 5. ft) of reach that can be enhanced with the optional 4,6 m (15 ft) swingaway extension to provide a total max tip height of 2,4 m (67 ft). Outriggers The YB5515-2 outriggers are two-position ( and 1 ) beam/jack style outriggers with inverted jack cylinders and pivoting pad. Steering The YB5515-2 comes standard with three steering modes: front (two-wheel), four-wheel coordinated, and four-wheel crab steer with electronic self alignment. Operators can choose between modes via three-position rocker switch located on dash panel. Operator cab New operator control layout with hydraulic proportional joystick controls, tilt steering wheel, and automotive dash panel gauges and indicator lights.
Contents Specifications 4 Dimensions and weights 7 Working ranges and load charts (imperial) 9 Working ranges and load charts (metric) 15 Working ranges and load charts (DIN/ISO) 21 Transport and lifting data 27 Rigging chart 28 Symbols glossary 29
Specifications Superstructure Boom 4,6 m 12,5 m (15 ft 41 ft) three-section, full-power, synchronized, telescopic boom. Maximum tip height: 14,2 m (46.5 ft) *Optional Boom 5,4 m 15,4 m (17.8 ft 5 ft) four-section, full-power, synchronized, telescopic boom. Maximum tip height: 16,5 m (54 ft) *Optional boom extensions 4,6 m (15 ft) fixed swingaway extension Maximum tip height with standard boom: 18,1 m (59.5 ft) Maximum tip height with optional boom: 2,4 m (67 ft) Boom extension can be offset, -15, and -3 via pivoting boom nose on the optional boom. Boom nose Fixed two-sheave quick reeve boom nose with standard 12,5 m (41 ft) boom. Two-sheave, quick reeve type with-3- pinned pivoting (, +4, and +8 ) boom nose design to minimize head space requirements. With optional boom only. Lowers head height,4 m (1.3 ft) when nose is pivoted fully forward. Boom elevation Single double acting hydraulic cylinder with integral holding valve. Elevation: to 69 Load Moment Indicator A simple, effective, and easy to use load moment indicating system used in conjunction with the anti-two block system to assist the operator in efficient operation of the unit within the limits of the load chart. The display panel displays the max. load allowed, the actual hook load, length and angle of the boom, and load radius in Dot Matrix numerical values and provides a load utilization colored bar graph. Inputs by operator are maximum allowed load and parts of line. If non-permitted conditions are approached the L.M.I. will warn the operator with an audible alarm and a warning light and will lock out those functions that may aggravate the condition. * Optional Load Moment Indicator Graphics Display of boom angle, boom length, load radius, and capacity. Operator input to set the limit parameters based on the load chart. Displays color coded light bar and audible alarm with function cut-out if load exceeds the load chart parameters. Swing Ball bearing swing circle with 36 continuous rotation. Worm gear and pinion driven by hydraulic motor. Spring applied, hydraulic released brake. Equipped with swing enable control. Maximum speed: 2.5 rpm Hydraulic system One pressure compensated variable displacement axial piston pump, with load sensing. Maximum output of: 155 LPM (41. GPM) Maximum operating pressure: 276 bars (4 p.s.i.) Four section valve bank, chassis mounted, operated via dash mounted pilot pressure hydraulic joystick controllers. Anti-two block device Standard anti-two block device (hardwired), which, when activated, provides an audible and visual warning to the operator and locks out all functions whose movement can cause two-blocking. 14L (37 gal) steel hydraulic reservoir with sight level gauge and steel side plating to guard against side impact. Return line replaceable filter with by-pass protection and service indicator. Cartridge filter rating of 3 micron. 4 *Denotes optional equipment
Specifications Hoist specifications Two speed gear motor driven hoist with automatic spring applied / hydraulically released wet brake. Smooth drum with cable follower. Maximum hoist pull (first layer): 63,6 kn (14,3 lb) Maximum permissible single line pull: 44,5 kn (1, lb.) (3.5:1 design factor) Maximum single line speed: 64 m/min (21 fpm) Rope construction: 6 x 19 XXIPS / IWRC Rope diameter: 14 mm (9/16 in) Rope length: 97,5 m (32 ft) Carrier Chassis High strength alloy frame constructed with integral outrigger housings; front and rear lifting, tie-down, and towing lugs. 6,2 m2 (66.3 sq ft) carry deck size with 972 kg (2, lb) deck only carrying capacity. Deck coated with anti-skid treatment. Engine (Tier IV) Cummins QSB 3.3L four cylinder / turbo-charged diesel rated at 75kW (1 hp) at 26 rpm. Includes std. 12V engine block heater and air intake Grid heater. Engine hour meter located in dash display. Alternator: 12 amp. Maximum Torque: 414Nm (35 ft/lb). Fuel requirements: Maximum of 15 ppm sulphur content. Requires Ultra Low sulphur diesel fuel. NOTE: Tier IV required for sale in North America and European Union countries. Engine (Tier III) Cummins QSB 3.3L four cylinder / turbo-charged diesel rated at 74kW (99 hp) at 26 rpm. Includes std. 12V engine block heater and air intake Grid heater. Engine hour meter located in dash display. Alternator: 9 amp. Maximum Torque: 415Nm (36 ft/lb) NOTE: Required for sale outside of North America and European Union countries. Fuel tank capacity Steel with side impact plate. Capacity: 151.4L (4 gal). Outriggers Single stage hydraulic telescoping beam with oblique style jack cylinder on all four corners. Provides extended and down and retracted and down lifting capabilities. Integral holding valve on both beam and jack. Outrigger positioning indicator located in dash display. Outrigger pad size: 222 mm x 254 mm (8.75 in x 1 in) Maximum outrigger pad load: 15 876 kg (35, lb) Outrigger controls Independent outrigger control rocker switches for beam or jack selection with a separate extend /retract rocker selector switch. 36 level bubble located inside cab. Transmission Powershift with four speeds forward and four reverse. Steering column mounted shifter. Operators control station Frame mounted, open air style control station with cab shell includes all crane functions and driving controls and equipped with overhead safety glass. Other standard equipment includes a suspension seat with seat belt, sight level bubble and 1,1 kg (2.5 lb) fire extinguisher, and tilt steering wheel. The dash panel will display the fuel level gauge, water temperature gauge, engine rpm, battery voltage, and hour meter. Indicator lights will display parking brake, low transmission pressure, low brake pressure, outrigger position, headlights, work lights (if ordered), and hoist 3rd wrap (if ordered). Crane function indicator and turn signal indicators are also included. The load indicator display will be mounted on the top of the dash panel for direct line of sight for the operator. *Denotes optional equipment Grove YB5515-2 5
Specifications *Operators control station enclosed Includes the standard cab shell and all controls and indicators noted above, with the addition of front, rear, and right side glass, a split (two-piece) hinged door with sliding glass, front windshield wiper and washer, hot water heater and defroster with fan and cab dome light. Electrical system One heavy duty maintenance free 12V battery, 82CCA at F Drive Two-wheel (front-wheel) as standard with four-wheeldrive as an option. Drive axles supplied with planetary hubs and limited slip differential. Lights Full LED lighting includes turn indicators, head, tail, brake, and hazard warning lights recessed mounted. Maximum speed 33.8 km/h (21. mph) Gradeability (theoretical) 68%...(to drive train stall) NO LOAD 4%...(to drive train stall) with 972 kg (2, lb) DECK LOAD Gross vehicle weight (G.V.W.) 13 488 kg (29,735 lb) basic unit with Tier IV engine. Steer Standard three steering modes. Front (two wheel), four wheel coordinated, and four wheel crab steer with electronic self realignment. Three position rocker switch located on dash panel. Outside Turning Radius: Two wheel steer: 6,2 m (2 ft 4.8 in) Four wheel steer: 3,9 m (13 ft 1. in) Suspension/axles Front: Drive / steer in both two wheel drive and four wheel drive Rear: non-drive with steer in two wheel drive, drive/steer in four wheel drive Front axle is rigid mounted to frame. Rear axle offers 1.5 of oscillation Brakes Hydraulic actuated internal wet-disc service brake acting on each drive wheel. Dash mounted rocker switch with indicator light for activating or release of the dry disc parking brake mounted on the transmission output yoke. Tires Tubeless type, semi-aggressive tread, 12.R2. Miscellaneous standard equipment 18 t (2 USt) two sheave low profile galvanize coated hook block with quick reeve design. Back-up motion alarm; outrigger motion alarm; non-skid decking; front and rear lifting, towing, and tie-down lugs. *Optional equipment AUXILIARY LIGHTING: Includes cab mounted amber flashing light and dual base boom mounted LED work lights. CONVENIENCE PACKAGE: Includes front and rear pintle hitch, dual rear view mirrors, head and tail light metal mesh grille covers. ENCLOSED CAB PACKAGE: Includes heater and defroster, cab dome light, all window glass, and two-piece split door. FOUR WHEEL DRIVE Below deck hydraulic tow winch with 4536 kg (1, lb) capacity. 4,6 m (15 ft) fixed boom extension Air conditioning (enclosed cab option required) Hoist third wrap indicator with hoist function cut-out Hoist drum rotation indicator 36 swing lock 6 C.E. compliant package *Denotes optional equipment
Dimensions Dimensions A B C D E 12.5 m (41 ft) boom E 15,2 m (5 ft) boom Two-wheel steer 3375 mm (11 ft 1 in) 658 mm (19 ft 1.5 in) 6218 mm (2 ft 4.8 in) 6675 mm (21 ft 1.8 in) 775 mm (25 ft 5 in) 7662 mm (25 ft 2 in) Four-wheel steer 1722 mm (5 ft 8 in) 41 mm (12 ft 7 in) 3993 mm (13 ft 1 in) 4481 mm (14 ft 8 in) 5572 mm (18 ft 3 in) 5478 mm (18 ft in) 15,2 m (5') BOOM PIVOTING NOSE *With optional boom only 114 mm (44.9") 8 1431 mm (56.3") 4 1546 mm (6.9") Dimensions are shown in mm (in). 2472 mm (97.3") 1283 mm (5.5") RADIUS E RADIUS B RADIUS D RADIUS C RADIUS A 71 mm (275.6") RETRACTED 12,5 m (41') BOOM 6871 mm (27.5") RETRACTED 15,2 m (5') BOOM R 214 mm (84.3") 12,5 m (41') BOOM 547 mm (212.9") RETRACTED 12 519 mm (492.9") EXTENDED 173 mm (6.8") 12,5 m (41')BOOM SHOWN 15,2 m (5') BOOM 5277 mm (27.8") RETRACTED 15 253 mm (6.5") EXTENDED 2475 mm (97.4") 154 mm(6.6") 223 mm (8.8") 2481 mm (97.7") 936 mm (36.9") 173 mm (42.4") 18 18 1195 mm (47.") 242 mm (95.3") 1994 mm (78.5") 42 mm (158.3") 4658 mm (183.4") Grove YB5515-2 7
Dimensions and weights 191 mm (75.2") 955 mm(37.6") 743 mm (29.3") 2737 mm (17.8") 1824 mm (71.8") 975 mm (.4") 1951 mm (76.8") 1159.84 mm (45.7") 232 mm (91.3") 2472 mm (97.3") 1994 mm (78.5") 13 mm (52.7") 165 mm (6.5") 122 mm (48.") 2439 mm (96.") 1336 mm (52.6") 2671 mm (15.2") 439 mm (159.") 4271 mm (168.1") 22 mm (79.5") 2136 mm (84.1") Weights Basic machine: Including 12,5 m (41 ft) main boom, main hoist with 97,5 m (32 ft) of wire rope, 18 t (2 USt) hook block, full counterweight, Tier IV engine GVW Front Rear kg lb kg lb kg lb 13 488 29,735 5817 12,823 7671 16,912 Add: enclosed cab, heater and glass 84,8 187 37,1 82 47,6 15 Crane weight 13 573 29,922 5854 12,95 7719 17,17 Basic machine: Including 12,5 m (41 ft) main boom, main hoist with 97,5 m (32 ft) of wire rope, 18 t (2 USt) hook block, full counterweight, Tier IV engine 13 488 29,735 5817 12,823 7671 16,912 Add: 4,6 m (15 ft) fixed swingaway extension and extension carrier brackets and downhaul weight 178 394 271 598-93 -24 Crane weight 13 666 3,129 688 13,421 7578 16,78 Basic machine: Including 12,5 m (41 ft) main boom, main hoist with 97,5 m (32 ft) of wire rope, 18 t (2 USt) hook block, full counterweight, Tier IV engine 13 488 29,735 5817 12,823 7671 16,912 Add: 5,4 m - 15,4 m (17.8 ft - 5 ft) four-section full-power boom 435 961 363 82 72 159 8 Crane weight 13 923 3,696 618 13,625 7743 17,71
Working range imperial Working range: 5,5 m -12,5 m (18 ft - 41 ft) boom (standard) 68 64 6 56 52 48 44 4 36 32 28 24 2 16 12 8 17.7' BOOM 26.' BOOM.' BOOM 41.1' BOOM 69 65 6 55 55 5 45 4 35 3 25 2 1 5 Height from the ground in feet 4 8 4 4 8 12 16 2 24 28 32 36 4 44 48 52 56 Operating radius in feet from axis of rotation Grove YB5515-2 9
Load chart imperial Radius (ft) 6 8 1 12 14 14.7 16 18 2 22 22.9 24 26 28 3 3.9 32 36 37.9 Radius (ft) 6 8 1 12 14 14.7 16 18 2 22 22.9 24 26 28 3 3.9 32 36 37.9 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Extended and Down 36 or Retracted and Down Front/Rear 17.7 ft BOOM 26 ft BOOM ft BOOM 41.1 ft BOOM Boom Rated Boom Rated Boom Rated Boom Rated Angle Load Angle Load Angle Load Angle Load (deg) (lb) (deg) (lb) (deg) (lb) (deg) (lb) 65 57 48 37.5 21.5 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Retracted and Down 36 17.7 ft BOOM 26 ft BOOM ft BOOM 41.1 ft BOOM Boom Rated Boom Rated Boom Rated Boom Rated Angle Load Angle Load Angle Load Angle Load (deg) (lb) (deg) (lb) (deg) (lb) (deg) (lb) 65 57 48 37.5 21.5 3, 26,85 22,3 18,6 15, 13,5 26, 19,5 13,63 973 739 681 68.5 63.5 58.5 53 51 46.5 4 31.5 19.5 68.5 63.5 58.5 53 51 46.5 4 31.5 19.5 26,4 21, 17,5 14,9 13,5 12,25 11, 92 74 69 17,94 12,89 992 772 68 6165 53 419 353 328 67 63 61.5 59 55 5.5 45.5 43.5 4.5.5 27 16.5 67 63 61.5 59 55 5.5 45.5 43.5 4.5.5 27 16.5 17, 14, 13,25 12,4 11,2 955 83 775 71 6 53 45 41 95 768 685 631 52 435 369 5 316 273 237 28 195 68.5 67.5 65.5 63 59 55.5 54 52 48 44 39.5.5 29 21 68.5 67.5 65.5 63 59 55.5 54 52 48 44 39.5.5 29 21 13,35 13,1 12,45 11,35 968 845 775 7 645 573 512 485 462 418 8 744 685 62 525 442 377 355 324 281 245 214 191 188 165 146 129 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B3.5-211. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (13 psi). Loads on rubber may be transported at a maximum speed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 2, lb. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. NOTES: SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 FRONT REAR 3 1
Load chart imperial Radius (ft) 6 8 1 12 14 14.7 16 18 2 22 22.9 24 26 28 3 3.9 32 36 37.9 MAIN BOOM ON RUBBER Any Boom Length Front Rating (lb) 36 Rating (lb) 17,8 14,6 11,8 955 81 75 693 561 4 7 3 396 365 33 286 253 231 21 235 1875 165 145 15,65 11,4 972 859 67 1 575 539 44 363 285 2585 2255 198 176 165 154 1375 126 11 NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 FRONT REAR 3 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B3.5-211. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (13 psi). Loads on rubber may be transported at a maximum speed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 2, lb. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. Grove YB5515-2 11
Working range imperial Working range: 5,4 m - 15,4 m (17.8 ft - 5 ft) (optional) 69 65' BOOM WITH 15' JIB 17.3' BOOM 29' BOOM 4' BOOM 5' BOOM 65 6 55 5 45 4 35 3 25 2 1 5 Height from the ground in feet Operating radius in feet from axis of rotation 12
Load chart imperial Radius (ft) 6 8 1 12 14.2 16 18 2 22 24 25.9 28 3 32 36 36.9 4 42 44 46.9 Radius (ft) 6 8 1 12 14.2 16 18 2 22 24 25.9 28 3 32 36 36.9 4 42 44 46.9 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Extended and Down 36 or Retracted and Down Front/Rear 1 7.3 ft BOOM 29 ft BOOM 4 ft BOOM 5 ft BOOM Boom Rated Boom Rated Boom Rated Boom Angle Load Angle Load Angle Load Angle (deg) (lb) (deg) (lb) (deg) (lb) (deg) 64.5 56.5 47 36 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Retracted and Down 36 Rated Load (lb) 1,99 983 87 75 662 58 51 6 462 41 6 371 359 1 276 241 211 1 7.3 ft BOOM 29 ft BOOM 4 ft BOOM 5 ft BOOM Boom Rated Boom Rated Boom Rated Boom Rated Angle Load Angle Load Angle Load Angle Load (deg) (lb) (deg) (lb) (deg) (lb) (deg) (lb) 64.5 56.5 47 36 3, 25,76 21,27 18,5 13,1 189 3, 25,76 18,6 13,4 1, 67 62.5 57.5 53 47.5 41 25 67 62.5 57.5 53 47.5 41 25 16,95 16,95 15,52 12,42 1,99 983 86 74 648 16,95 13,3 1,4 855 75 592 54 433 378 67.5 65 61.5 58 54.5 51 47 42.5 32.5 25.5 16 67.5 65 61.5 58 54.5 51 47 42.5 32.5 25.5 16 15,52 12,42 1,99 98 867 749 658 577 513 451 41 2 371 362 997 85 715 63 516 445 39 339 298 263 233 26 196 68.5 66 63 6.5 58 55 52 49 45.5 42 4.5 29 23 68.5 66 63 6.5 58 55 52 49 45.5 42 4.5 29 23 695 591 56 439 6 337 297 263 2 28 197 185 165 147 131 11 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B3.5-211. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (13 psi). Loads on rubber may be transported at a maximum speed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 2, lb. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. NOTES: SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 FRONT REAR 3 Grove YB5515-2 13
Load chart imperial Radius (ft) 6 8 1 12 14.2 16 18 2 22 24 25.9 28 3 32 36 36.9 4 42 44 46.9 MAIN BOOM ON RUBBER Any Boom Length Front Rating (lb) 36 Rating (lb) 17,8 14,35 11,45 979 817 72 621 554 483 416 363 328 291 26 232 28 198 19 17 152 137 116 15,55 11,5 895 742 63 535 445 367 35 264 222 196 165 14 117 99 9 82 67 51 42 NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 FRONT REAR 3 Main Boom Angle (deg) 69 65 6 55 5 45 4 35 3 25 2 15 1 5 15 FT FIXED JIB CAPACITIES ON EXTENDED OUTRIGGERS Jib Offset Angle deg 15 deg 3 deg To 4 ft 75 718 6 518 458 44 9 277 254 237 224 216 212 211 To 5 ft 72 567 477 413 4 286 244 212 189 171 157 148 141 1 137 To 4 ft 548 489 444 41 3 362 327 293 266 247 232 222 To 5 ft 528 451 394 352 317 268 232 24 183 167 155 146 To 4 ft 395 369 351 322 313 37 286 263 To 5 ft 395 369 351 321 297 258 225 2 181 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B3.5-211. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (13 psi). Loads on rubber may be transported at a maximum speed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 2, lb. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 14
Working range metric Working range: 5,5 m -12,5 m boom (standard) 2,7 3 19,51 18,29 17,7 15,85 14,63 13,41 12,19 1,97 9,7 5 8,53 7,32 6,1 4,88 3,66 2,44 1,22 5,4 M BOOM 7,9 M BOOM 1,4 M BOOM 12,5 M BOOM 69 65 6 55 5 45 4 35 3 25 2 1 5 Height from the ground in meters -2,44-1,22 1,22 2,44 3,66 4,88 6,1 7,32 8,53 9,7 5 1,97 12,1 9 13,41 14,63 15,85 17,7 Operating radius in meters from axis of rotation Grove YB5515-2 15
Load chart metric Radius (m) 1,8 2,4 3, 3,7 4,3 4,5 4,9 5,5 6,1 6,7 7, 7,3 7,9 8,5 9,1 9,4 9,8 1,4 11, 11,6 Radius (m) 1,8 2,4 3, 3,7 4,3 4,5 4,9 5,5 6,1 6,7 7, 7,3 7,9 8,5 9,1 9,4 9,8 1,4 11, 11,6 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Extended and Down 36 or Retracted and Down Front/Rear 5.4 m BOOM 7.9 m BOOM 1.4 m BOOM 1 2.5 m BOOM Boom Rated Boom Rated Boom Rated Boom Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 65 57,5 49 36,5 2,5 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Retracted and Down 36 5,4 m BOOM 7,9 m BOOM 1,4 m BOOM 1 2,5 m BOOM Boom Rated Boom Rated Boom Rated Boom Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 65 57,5 49 36,5 2,5 13 6 12 1 75 985 85 68 6125 11 775 884 61 8 441 335 69 64 58 52,5 51 46,5 39,5 31,5 19,5 69 64 58 52,5 51 46,5 39,5 31,5 19,5 11 975 9525 7925 675 6125 555 497 5 415 335 3125 813 548 45 35 279 228 19 16 148 66,5 63 61,5 59 54,5 5,5 45,5 43,5 4,5,5 27,5 17,5 66,5 63 61,5 59 54,5 5,5 45,5 43,5 4,5,5 27,5 17,5 77 635 6 56 575 4325 375 35 32 27 24 225 185 43 8 31 286 235 197 167 156 143 123 17 94 885 68,5 67,5 65,5 62 59 55,5 54 52 48 44 4 37,5 28 2,5 68,5 67,5 65,5 62 59 55,5 54 52 48 44 4 37,5 28 2,5 65 5925 5625 5125 4375 25 351 5 3325 2925 26 232 22 29 189 172 157 337 31 281 2 2 171 161 147 127 111 97 86 85 74 66 58 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B3.5-211. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 726 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. NOTES: SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 FRONT REAR 3 16
Load chart metric Radius (m) 1,8 2,4 3, 3,7 4,3 4,5 4,9 5,5 6,1 6,7 7, 7,3 7,9 8,5 9,1 9,4 9,8 1,4 11, 11,6 MAIN BOOM ON RUBBER Any Boom Length Front Rating (kg) 36 Rating (kg) 87 662 535 433 363 314 254 214 179 165 149 129 11 4 14 95 92 85 75 65 71 517 44 9 26 244 199 164 139 129 117 12 89 79 74 69 62 57 49 NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 FRONT REAR 3 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B3.5-211. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 726 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. Grove YB5515-2 17
Working range metric Working range: 5,4 m - 15,4 m (optional) 23,8 23,2 22,6 21,9 21,3 2,7 2,1 19,5 18,9 18,3 17,7 17,1 16,5 15,8 15,2 14,6 14, 13,4 12,8 12,2 11,6 11, 1,4 9,8 9,1 8,5 7,9 7,3 6,7 6,1 5,5 4,9 4,3 3,7 3, 2,4 1,8 1,2,6 1,8,6,6 1,8 3, 4,3 5,5 6,7 7,9 9,1 1,4 11,6 12,8 14, 15,2 15,8 17,1 18,3 19,5 2,4 1,2 1,2 2,4 3,7 4,9 6,1 7,3 8,5 9,8 11, 12,2 13,4 14,6 15,2 16,5 17,7 18,9 5,3 m BOOM 8,8 m BOOM 12,2 m BOOM 15,2 m BOOM 19,8 m BOOM WITH 4,6 m J IB 65 6 69 55 5 45 2,4 1,2 1,2 2,4 3,7 4,9 6,1 7,3 8,5 9,8 11, 12,2 13,4 14,6 15,2 16,5 17,7 18,9 1,8,6,6 1,8 3, 4,3 5,5 6,7 7,9 9,1 1,4 11,6 12,8 14, 15,2 15,8 17,1 18,3 19,5 4 35 3 25 2 1 5 23,8 23,2 22,6 21,9 21,3 2,7 2,1 19,5 18,9 18,3 17,7 17,1 16,5 15,8 15,2 14,6 14, 13,4 12,8 12,2 11,6 11, 1,4 9,8 9,1 8,5 7,9 7,3 6,7 6,1 5,5 4,9 4,3 3,7 3, 2,4 1,8 1,2,6 Height from the ground in meters Operating radius in meters from axis of rotation 18
Load chart metric Radius (m) 1,8 2,4 3, 3,7 4,3 4,9 5,5 6,1 6,7 7,3 7,9 8,5 9,1 9,8 1,4 11, 11,2 11,6 12,2 12,8 13,4 14,3 Radius (m) 1,8 2,4 3, 3,7 4,3 4,9 5,5 6,1 6,7 7,3 7,9 8,5 9,1 9,8 1,4 11, 11,2 11,6 12,2 12,8 13,4 14,3 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Extended and Down 36 or Retracted and Down Front/Rear 5,3 m BOOM 8,8 m BOOM 12,2 m BOOM 15,2 m BOOM Boom Rated Boom Rated Boom Rated Boom Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 65 57 48 35 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Retracted and Down 36 5,3 m BOOM 8,8 m BOOM 12,2 m BOOM 15,2 m BOOM Boom Rated Boom Rated Boom Rated Boom Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 65 57 48 35 13 6 11 68 964 818 594 189 13 6 11 685 843 5955 4585 67,5 62,5 57,5 52,5 47 41 25 67,5 62,5 57,5 52,5 47 41 25 7685 7685 725 563 498 445 39 335 293 7685 5955 477 5 3185 268 229 197 1715 68 64,5 61,5 58 54,5 51 47 43 32 25 15,5 68 64,5 61,5 58 54,5 51 47 43 32 25 15,5 73 563 498 4445 393 339 298 261 232 245 1865 168 164 4565 3 323 2735 25 225 177 155 1365 1185 15 93 895 68,5 66 63 6,5 58 55 52 48,5 45,5 42 4,5 29 23,5 68,5 66 63 6,5 58 55 52 48,5 45,5 42 4,5 29 23,5 498 4455 394 3 263 2 295 1885 168 1625 1545 1375 125 19 995 314 2675 23 1995 175 154 136 1185 155 94 95 835 745 665 595 5 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B3.5-211. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 726 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. NOTES: SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 FRONT REAR 3 Grove YB5515-2 19
Load chart metric MAIN BOOM ON RUBBER Any Boom Length Radius (m) Front Rating (kg) 36 Rating (kg) 1,8 89 77 2,4 6525 523 3, 521 46 3,7 444 3365 4,3 375 276 4,9 31 85 2425 5,5 282 215 6,1 251 1665 6,7 219 1 7,3 189 1195 7,9 1645 15 8,5 1495 885 9,1 133 745 9,8 1165 635 1,4 145 53 11, 94 445 11,2 95 45 11,6 855 37 12,2 77 3 12,8 69 23 13,4 62 19 14,3 525 NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 FRONT REAR 3 Main Boom Angle (deg) 69 65 6 55 5 45 4 35 3 25 2 15 1 5 4,6 m FIXED JIB CAPACITIES ON EXTENDED OUTRIGGERS Jib Offset Angle 3 To 1 2,2 m 3255 27 2 235 27 5 183 158 1395 125 11 5 175 115 98 96 955 To 1 5,2 m 318 257 216 187 156 1295 115 96 85 775 71 67 64 625 62 To 1 2,2 m 2485 221 5 21 186 1735 164 148 1325 125 112 15 15 To 1 5,2 m 2395 245 1785 1595 1435 121 15 925 83 75 7 66 To 1 2,2 m 179 167 159 154 146 142 139 1295 11 95 To 1 5,2 m 179 167 159 1455 15 11 7 12 9 82 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B3.5-211. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 726 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. 2
Working range DIN/ISO Working range: 5,5 m -12,5 m boom (standard) 2,73 19,51 18,29 17,7 15,85 14,63 13,41 12,19 1,97 9,7 5 8,53 7,32 6,1 4,88 5,4 M BOOM 7,9 M BOOM 1,4 M BOOM 12,5 M BOOM 69 65 6 55 5 45 4 35 3 25 2 Height from the ground in meters 3,66 2,44 1,22 1 5-2,44-1,22 1,22 2,44 3,66 4,88 6,1 7,32 8,53 9,7 5 1,97 12,19 13,41 14,63 15,85 17,7 Operating radius in meters from axis of rotation Grove YB5515-2 21
Load chart DIN/ISO Radius (m) 1,8 2,4 3, 3,7 4,3 4,5 4,9 5,5 6,1 6,7 7, 7,3 7,9 8,5 9,1 9,4 9,8 1,4 11, 11,6 Radius (m) 1,8 2,4 3, 3,7 4,3 4,5 4,9 5,5 6,1 6,7 7, 7,3 7,9 8,5 9,1 9,4 9,8 1,4 11, 11,6 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Extended and Down 36 or Retracted and Down Front/Rear 5,4 m BOOM 7,7 m BOOM 1,4 m BOOM 1 2,5 m BOOM Boom Rated Boom Rated Boom Rated Boom Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 65 57,5 49 36,5 2,5 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Retracted and Down 36 5,4 m BOOM 7,9 m BOOM 1,4 m BOOM 1 2,5 m BOOM Boom Rated Boom Rated Boom Rated Boom Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 65 57,5 49 36,5 2,5 13 6 13 523 11 85 1 5 898 739 13 6 11 125 85 586 451 5 421 69 64 58 52,5 51 46,5 39,5 31,5 19,5 69 64 58 52,5 51 46,5 39,5 31,5 19,5 12 1 1 85 968 875 846 7745 63 527 4495 421 9955 7395 5625 462 437 5 45 3185 2685 2295 2145 66,5 63 61,5 59 54,5 5,5 45,5 43,5 4,5,5 27,5 17,5 66,5 63 61,5 59 54,5 5,5 45,5 43,5 4,5,5 27,5 17,5 9115 821 7935 732 6235 533 4565 428 397 35 31 1 5 279 2645 535 445 41 85 3735 3215 2735 236 221 5 26 1815 165 143 135 68,5 67,5 65,5 62 59 55,5 54 52 48 44 4 37,5 28 2,5 68,5 67,5 65,5 62 59 55,5 54 52 48 44 4 37,5 28 2,5 789 762 6985 598 521 459 435 3995 3525 3145 2825 268 251 5 2285 285 1925 421 5 41 5 36 312 2735 242 229 21 3 1875 1665 149 145 131 118 165 97 5 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 8% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 726 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. 3 FRONT REAR 3 22
Load chart DIN/ISO MAIN BOOM ON RUBBER Any Boom Length Radius (m) Front Rating (kg) 36 Rating (kg) 1,8 2,4 3, 3,7 4,3 4,5 4,9 5,5 6,1 6,7 7, 7,3 7,9 8,5 9,1 9,4 9,8 1,4 11, 11,6 87 662 535 433 363 25 31 65 263 2225 195 1785 175 15 133 1185 112 16 95 855 775 7115 519 441 3765 297 27 8 257 21 45 182 1565 1465 14 1225 175 95 89 825 735 65 585 NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 8% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 726 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. Grove YB5515-2 23
Working range DIN/ISO Working range: 5,4 m - 15,4 m (optional) 23,8 23,2 22,6 21,9 21,3 2,7 2,1 19,5 18,9 18,3 17,7 17,1 16,5 15,8 15,2 14,6 14, 13,4 12,8 12,2 11,6 11, 1,4 9,8 9,1 8,5 7,9 7,3 6,7 6,1 5,5 4,9 4,3 3,7 3, 2,4 1,8 1,2,6 1,8,6,6 1,8 3, 4,3 5,5 6,7 7,9 9,1 1,4 11,6 12,8 14, 15,2 15,8 17,1 18,3 19,5 2,4 1,2 1,2 2,4 3,7 4,9 6,1 7,3 8,5 9,8 11, 12,2 13,4 14,6 15,2 16,5 17,7 18,9 5,3 m FT BOOM 8,8 m BOOM 12,2 m BOOM 15,2 m BOOM 19,8 m BOOM WITH 4,6 m JIB 69 65 6 55 5 45 4 35 2,4 1,2 1,2 2,4 3,7 4,9 6,1 7,3 8,5 9,8 11, 12,2 13,4 14,6 15,2 16,5 17,7 18,9 1,8,6,6 1,8 3, 4,3 5,5 6,7 7,9 9,1 1,4 11,6 12,8 14, 15,2 15,8 17,1 18,3 19,5 3 25 2 1 5 23,8 23,2 22,6 21,9 21,3 2,7 2,1 19,5 18,9 18,3 17,7 17,1 16,5 15,8 15,2 14,6 14, 13,4 12,8 12,2 11,6 11, 1,4 9,8 9,1 8,5 7,9 7,3 6,7 6,1 5,5 4,9 4,3 3,7 3, 2,4 1,8 1,2,6 Height from the ground in meters Operating radius in meters from axis of rotation 24
Load chart DIN/ISO Radius (m) 1,8 2,4 3, 3,7 4,3 4,9 5,5 6,1 6,7 7,3 7,9 8,5 9,1 9,8 1,4 11, 11,2 11,6 12,2 12,8 13,4 14,3 Radius (m) 1,8 2,4 3, 3,7 4,3 4,9 5,5 6,1 6,7 7,3 7,9 8,5 9,1 9,8 1,4 11, 11,2 11,6 12,2 12,8 13,4 14,3 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Extended and Down 36 or Retracted and Down Front/Rear 5,3 m BOOM 8,8 m BOOM 1 2,2 m BOOM 1 5,2 m BOOM Boom Rated Boom Rated Boom Rated Boom Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 65 57 48 35 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Retracted and Down 36 5,3 m BOOM 8,8 m BOOM 1 2,2 m BOOM 1 5,2 m BOOM Boom Rated Boom Rated Boom Rated Boom Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 65 57 48 35 13 6 13 375 11 725 1 125 594 189 13 6 11 35 81 6 5955 4585 67,5 62,5 57,5 52,5 47 41 25 67,5 62,5 57,5 52,5 47 41 25 7685 7685 7685 73 6335 5285 45 85 324 721 548 449 3765 31 85 268 229 197 1715 68 64,5 61,5 58 54,5 51 47 43 32 25 15,5 68 64,5 61,5 58 54,5 51 47 43 32 25 15,5 721 657 5 597 51 75 4535 3925 5 272 245 21 75 197 191 41 65 3525 33 263 235 225 177 155 1365 1185 15 93 895 68,5 66 63 6,5 58 55 52 48,5 45,5 42 4,5 29 23,5 68,5 66 63 6,5 58 55 52 48,5 45,5 42 4,5 29 23,5 545 495 4325 55 2 335 272 241 5 2195 1995 1935 182 166 1525 14 124 287 255 225 1955 174 154 136 11 85 155 94 95 835 745 665 595 5 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 8% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 726 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. NOTES: SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 FRONT REAR 3 Grove YB5515-2 25
Load chart DIN/ISO MAIN BOOM ON RUBBER Any Boom Length Radius (m) Front Rating (kg) 36 Rating (kg) 1,8 89 77 2,4 6525 523 3, 521 46 3,7 444 3365 4,3 364 2685 4,9 2365 5,5 262 1945 6,1 221 162 6,7 188 1365 7,3 1615 116 7,9 1395 99 8,5 1265 885 9,1 112 745 9,8 97 5 635 1,4 865 53 11, 77 445 11,2 74 45 11,6 7 37 12,2 62 3 12,8 55 23 13,4 49 19 14,3 45 NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 FRONT REAR 3 Main Boom Angle (deg) 69 65 6 55 5 45 4 35 3 25 2 15 1 5 4,6 m FIXED JIB CAPACITIES ON EXTENDED OUTRIGGERS Jib Offset Angle 3 To 1 2,2 m 3255 272 235 275 187 1715 158 1445 133 1255 125 1165 114 1135 To 1 5,2 m 31 8 257 21 6 187 1655 141 124 1115 15 915 86 82 785 77 765 To 1 2,2 m 2485 221 5 21 186 1735 164 154 146 139 135 1245 119 To 1 5,2 m 2395 245 1785 1595 1455 1325 118 165 97 5 95 855 815 To 1 2,2 m 179 167 159 154 146 142 139 137 136 To 1 5,2 m 179 167 159 1455 15 1265 1145 15 955 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 8% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 726 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. 4) Ratings on outriggers are for either outriggers fully extended and 26