product guide contents Features 2 Specifications 3 Dimensions 5 Working Range 6 features - ton (-55 mt) capacity 36 ft-1 ft (11 m-33.5 m) 4 section, full power boom 33 ft (.1 m) offsettable lattice swingaway extension 33 ft-56 ft (.1 m-17.1 m) bifold lattice swingaway extension 20 ft (6.1 m) or ft (12.2 m) extension inserts Grove MEGAFORM boom 12,1 lbs (5,511 kg) Counterweight pinned to superstructure 2 bhp (179 kw) Cummins diesel engine Grove E series cab Bifold Load Charts 7 Working Range Bifold & Inserts Load Charts 11 Load Handling 15 Rough Terrain Hydraulic Crane
2 features The superstructure features a fullpower four-section MEGAFORM boom that can reach to a maximum tip height of 119 ft. The sequence synchronized extension feature: telescopes boom sections with a touch of the hand via a single lever joystick controller. The has a quick-reeve boom nose and swingaway alignment device to help operators set up smoothly. An optional bi-fold swingaway lattice extension easily stows on the side of the base boom for easy transport while providing onboard extension from 33-56 ft. for a maximum tip height of 174.5 ft. By adding inserts of 20 or ft. the max tip height on the can be extended even further to 194 ft. or 214 ft. An optional 33 ft. fixed swingaway is also available with a max tip height of 1 ft. The features common to the Grove E Series cab include: hot water heater/defroster single axis joystick controllers sliding skylight and adjustable sunscreen engine instrumentation full acoustical lining The PAT iflex 5 graphic display LMI includes a work area definition system which allows the operator to define a preferred working area. Large open stowage compartment for tools and rigging accessories.
specifications Superstructure Boom 36 ft. - 1 ft. (11 m - 33.5 m) four-section, full-power sequenced synchronized boom. Maximum tip height: 119 ft. (36.4 m). *Optional Fixed Swingaway Extension 33 ft. (.1 m) offsettable lattice swingaway extension. Offsettable at 0, 25 and 45. Stows alongside base boom section. Maximum tip height: 1 ft. (45.8 m). *Optional Bi-Fold Swingaway Extension 33 ft. - 56 ft. (.1 m - 17.1 m) bi-fold lattice swingaway extension. Offsettable at 0, 25 and 45. Stows alongside base boom section. Maximum tip height: 174.5 ft. (53.2 m). *Optional 20 ft. (6.1 m) or ft. (12.2 m) Inserts Installs between boom nose and bi-fold extension, nonstowable. Maximum tip height: 194 ft. (59.1 m)-20 ft. insert, 214 ft. (65.2 m)- ft. insert. Boom Nose Three nylatron sheaves (four with -ton rating) mounted on heavy-duty tapered roller bearings with removable pin-type rope guards. Quick-reeve type boom nose. *Optional removable auxiliary boom nose with removable pin type rope guard. Boom Elevation One double-acting hydraulic cylinder with integral holding valve provides elevation from -3 to 78. Swing Planetary swing with foot-applied multi-disc brake. Spring applied, hydraulically-released swing brake and plunger-type, one position, mechanical house lock operated from cab. *Optional 3 mechanical swing lock. Maximum speed: 2.5 RPM. Counterweight 12,1 lbs. (5511 kg) pinned to superstructure. Hydraulic System Three main gear pumps with a combined capacity of 3 GPM (391 LPM), 135 GPM (511 LPM) with optional air conditioning. Maximum operating pressure: 00 psi (27.6 MPa). Two individual post pressure compensated valve banks. Return line type filter with full flow by-pass protection and service indicator. Replaceable cartridge with micron filtration rating of 5/12/16. 132 gallon (0 L) reservoir. Integral oil cooler. System pressure test ports. Hoist Specifications Main and Auxiliary Hoist: Grove Model HOG-16G Planetary reduction with automatic spring applied multi-disc brake. Grooved drum. Electronic hoist drum rotation indicator and hoist drum cable followers. Maximum Single Line Pull: Maximum Single Line Speed: 18,1 lbs (8 246 kg) 588 FPM (179 m/min) 3 Load Moment & Anti-Two Block System Standard Graphic Display load moment and anti-two block system with audio-visual warning and control lever lockout. These systems provide electronic display of boom angle, length, radius, tip height, relative load moment, maximum permissible load, load indication and warning of impending two-block condition. The standard Work Area Definition System allows the operator to pre-select and define safe working areas. If the crane approaches the pre-set limits, audio-visual warnings aid the operator in avoiding job-site obstructions. Cab Full-vision, all-steel fabricated with acoustical lining and tinted safety glass throughout. Deluxe seat incorporates armrestmounted hydraulic single-axis controllers. Dash panel incorporates gauges for all engine functions. Other standard features include: hot water heater, cab circulating air fan, sliding side and rear windows, sliding skylight with electric wiper and sunscreen, electric windshield wash/wipe, fire extinguisher and seat belt. Maximum Permissible Line Pull: 16,0 lbs. (7 620 kg) w/standard 6 x 37 class rope 16,0 lbs. (7 620 kg) w/optional 35 x 7 class rope Rope Diameter: 3/4 in. (19 mm) Rope Length: 0 ft. (152 m) *Optional 5 ft. (168 m) 35 x 7 class rope Rope Type: 6 x 37 class EIPS IWRC *Optional 35 x 7 class rotation resistant Maximum Rope Stowage: 694 ft. (211 m) Optional H0G-26G Main Hoist Rope: 6 ft. (198 m) 6 x 37 class rope Stowage: 1193 ft. (355 m)
specifications 4 Carrier Chassis Box section frame fabricated from high-strength, low alloy steel. Integral outrigger housings and front/rear towing and tie down lugs. O Outrigger System Four hydraulic telescoping single-stage double box beam outriggers with inverted jacks and integral holding valves. Three position settings, %, % and fully retracted. All steel fabricated, quick-release type round outrigger floats, 24 in. (6 mm) diameter. Maximum outrigger pad load:,0 lbs (36,6 kg). Brakes Full hydraulic split circuit brakes operating on all wheels. Springapplied, hydraulically released axle-mounted parking brake. Tires 29.5 x 25-28PR bias earthmover type. *29.5R25 radial earthmover type. Lights Full lighting package including turn indicators, head, tail, brake and hazard warning lights. Maximum Speed 23 MPH (37 km/h). Outrigger Controls Controls and crane level indicator located in cab. Engine Cummins QSB 5.9L diesel, six cylinders, turbocharged, 2 bhp (179 kw) (Gross) @ 2,0 rpm. Maximum torque: 7 ft. lbs. (9 N-m) @ 1,0 RPM. Fuel Tank Capacity 72 gallons (273 L) Transmission Spicer powershift with 6 forward and 6 reverse speeds (3 speeds high and 3 speeds low). Front axle disconnect for 4 x 2 travel. Electrical System Two 12-volt maintenance free batteries. 12-volt starting and lighting, circuit breakers, battery disconnect switch. Drive 4 x 4 Steering Fully independent power steering: Front: Full hydraulic, steering wheel controlled. Rear: Full hydraulic, switch controlled. Provides infinite variations of 4 main steering modes: front only, rear only, crab and coordinated. Rear steer centered indicating light. 4 wheel turning radius - 22 ft. 2 in. (6.7 m). Axles Front: Drive/steer with differential and planetary reduction hubs rigid-mounted to frame. Rear: Drive/steer with differential and planetary reduction hubs pivot-mounted to frame. Automatic full hydraulic lockouts on rear axle permit 8 in. (203 mm) oscillation only with boom centered over the front. Gradeability (Theoretical) 75% (Based on 89,000 lbs. [ 3 kg] GVW) 29.5 x 25 tires, pumps engaged, 1 ft. (33.6 m) boom, and bi-fold extension. Miscellaneous Standard Equipment Full width steel fenders, dual rear view mirrors, hookblock tiedown, electronic back-up alarm, light package, front stowage well, tachometer, rear wheel position indicator, 36,000 BTU hot water heater, hoist mirrors, engine distress A/V warning system. Auxiliary hoist control valve arrangement (less hoist). Cold start aid and immersion type engine block heater, 120V watt. *Optional Equipment *Auxiliary Hoist Package (includes Model HOG-16G auxiliary hoist with electronic hoist drum rotation indicator, hoist drum cable follower, 0 ft. (152 m) of 3/4 in.(19 mm) 35 X 7 class wire rope, auxiliary single sheave boom nose.) *AIR CONDITIONING PACKAGE (includes hydraulic driven 28,0 BTU air conditioning) *Auxiliary Lighting Package (includes cab mounted amber flashing light, 3 rotation spotlight and dual base boom mounted floodlights) *CONVENIENCE PACKAGE (includes in cab LMI light bar) * CE Mark Conformance (includes European boom, battery disconnect switch, 3rd wrap indicator, electric emergency auxiliary steering, dual axis joystick controllers) *Cross axle differential locks (front and rear) *Full-length aluminum decking *Manual pump disconnect *Pintle hook - rear *3 degree NYC style positive swinglock *Rubber mat for stowage trough *PAT datalogger *Aluminum fender protectors *Denotes optional equipment
dimensions 44'-1.83" (13458mm) C L ROTATION 5 1'-7.49" (495mm) 22 DEGREES 11.05" (281mm) 1'-5.69" (449mm) 11'-.88" (3629mm) 16'-.00" (5131mm) 11'-3.12" (3432mm) 13'-4.00" (64mm) 11'-11.12" (3635mm) 20 DEGREES 26'-5.00" (45mm) TAILSWING 13'-7.95" (4164mm) TRACK 8'-2.44" (20mm) '-5.00" (3175mm) RETRACTED 17'-4.00" (5283mm) MID EXTEND 23'-4.00" (71mm) FULL EXTEND TURNING RADIUS 2 WHEEL STEER 37'-3" (11342mm) 4 WHEEL STEER 22'-2" (6743mm) '-.94" (3326mm) 26 25 Note: ( ) Reference dimensions in mm Weights GVW Front Rear lb. kg lb. kg lb. kg Basic Machine 84,1 38,466,719 18,4 44,082 19,996 ADD: 33-56 ft. bi-fold swingaway 2,4 1,125 3,968 1,0-1,488-675 ADD: 33 ft. swingaway 1,7 785 3,082 1,398-1,352-613 ADD: Auxiliary hoist cable 625 284-2 -4 855 388 ADD: Auxiliary boom nose 1 59 374 1-244 -111 ADD: ton (55 mt) 5-sheave hookblock 1,2 567 1,2 567 0 0 (stowed in trough) ADD: ton (45 mt) 3-sheave hookblock 1,000 454 1,000 454 0 0 (stowed in trough) ADD: 8.3 ton (7.5 mt) headache ball 3 168 2 273-232 -5 (hanging from aux. nose) Remove: Counterweight -12,1-5,511 4,784 2,1-16,934-7,681
working range Working range 1 ft. Main Boom & 33-56 ft. bi-fold swingaway 6 H [ft] 1 25 0 56' EXT. 1 45 1 1 33' EXT. 1 1 120 1 1 Height from the ground in feet 20 36 Boom and extension length in feet 20 0 78 MAX. BOOM ANGLE 0 1 1 1 1 120 1 20 Operating radius in feet from axis of rotation R [ft] AXIS OF ROTATION 8'-3" 8'-8" Dimensions are for largest Grove furnished hook block and headache ball, with anti-two block activated. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
RT7E load chart 36-1 ft. 12,1 lbs % 23 ft. 4 in. spread 12 15 20 25 35 45 55 65 75 85 95 3¼ Pounds 36 ** 1,000,000 85,0 65,0 (49) 52,0 (36) 84,0 84,0 82,0 65,000 (55) 52,4 42,1 (31.5),200,200,200 64,0 51,8 39,0 31,7 () 24,4 (28) *62,0 62,0 (77) 61,000 (74),6 41,0 38,000 (57.5) 29,7 (51.5) 24,7 19,7 (37) 16,000 (26.5) *36,0 36,0 36,0 36,0 33,0 28,0 23,0 (53) 19,0 (47.5) 16,7 (41) 13,6 (33.5) 11,1 (24) *36,0 36,0 34,000 29,000 (67) 25,000 22,000 (59) 18,0 (54.5) 16,0 (49.5) 14,0 (44.5) 12,000 (38.5), (31.5) 8,4 (22.5) *31,000 31,000 (77),000 25,0 (.5) 22,200 (67) 20,200 17,0 16,000 (55.5) 14, (51) 12,200 (47),0 (42) 9,4 (36.5) 8, () 6,920 (21.5) *29, 27,000 24,200 (72.5) 21,7 (69.5) 19,000 (66.5) 17,0 16,000 14, 12,200 (52.5),0 9,000 (44.5) 7,0 () 6,0 (34.5) 5,0 (28.5) 5,000 (20.5) *24,000 24,000 22,000 20,000 18,0 17,0 (66.5) 16,000 14, 12,200 (57),0 (53.5) 9,000 () 7,0 (46.5) 6,0 (42.5) 5,0 (38) 5,000 (33) 4,4 (27.5) 3,8 (19.5) 7 Minimum boom angle (¼) for indicated length (no load) 0 Maximum boom length (ft.) at 0¼ boom angle (no load) 1 NOTE: ( ) Boom angles are in degrees. #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based on maximum boom angle. Lifting Capacities at Zero Degree Boom Angle On Outriggers Fully Extended - 3¼ Boom Main Boom Length in Angle 36 ** 1 0¼ 29,0 (29.8) 24,4 (34.2) 17,0 (44.2) 11,9 (54.6) 9,0 (64.2) 7,3 (74.2) 6,0 (84.2) 4,6 (94.2) 3,3 (4.2) NOTE: ( ) Reference radii in feet. ** Boom length is with inner-mid fully extended and outer-mid & fly fully retracted. A6-829- THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
RT7E load chart 8 36-1 ft. 12,1 lbs % 23 ft. 4 in. spread 12 15 20 25 35 45 55 65 75 85 95 3¼ Pounds 36 ** 1 120,000,000 85,0 65,0 (49) 52,0 (36) 84,0 84,0 82,0 65,000 (55) 52,4 42,1 (31.5),200,200,200 64,0 51,8 39,0 31,7 () 24,4 (28) *62,0 62,0 (77) 61,000 (74),6 41,0 38,000 (57.5) 29,7 (51.5) 24,7 19,7 (37) 16,000 (26.5) *36,0 36,0 36,0 36,0 33,0 28,0 23,0 (53) 19,0 (47.5) 16,7 (41) 13,6 (33.5) 11,1 (24) *36,0 36,0 34,000 29,000 (67) 25,000 22,000 (59) 18,0 (54.5) 16,0 (49.5) 14,0 (44.5) 12,000 (38.5), (31.5) 8,4 (22.5) *31,000 31,000 (77),000 25,0 (.5) 22,200 (67) 20,200 17,0 16,000 (55.5) 14, (51) 12,200 (47),0 (42) 9,4 (36.5) 8, () 6,920 (21.5) *29, 27,000 24,200 (72.5) 21,7 (69.5) 19,000 (66.5) 17,0 16,000 14, 12,200 (52.5),0 9,000 (44.5) 7,0 () 6,0 (34.5) 5,0 (28.5) 5,000 (20.5) *24,000 24,000 22,000 20,000 18,0 17,0 (66.5) 16,000 14, 12,200 (57),0 (53.5) 9,000 () 7,0 (46.5) 6,0 (42.5) 5,0 (38) 5,000 (33) 4,4 (27.5) 3,8 (19.5) Minimum boom angle (¼) for indicated length (no load) 0 Maximum boom length (ft.) at 0¼ boom angle (no load) 1 NOTE: ( ) Boom angles are in degrees. #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based on maximum boom angle. Lifting Capacities at Zero Degree Boom Angle On Outriggers Fully Extended - 3¼ Boom Main Boom Length in Angle 36 ** 1 0¼ 29,0 (29.8) 24,4 (34.2) 17,0 (44.2) 11,9 (54.6) 9,0 (64.2) 7,3 (74.2) 6,0 (84.2) 4,6 (94.2) 3,3 (4.2) NOTE: ( ) Reference radii in feet. ** Boom length is with inner-mid fully extended and outer-mid & fly fully retracted. A6-829- THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
load chart 36-1 ft. 33-56ft. 12,1 lbs % 23 ft. 4 in.spread 0¼ Pounds 33 ft. LENGTH 56 ft. LENGTH 25¼ 45¼ 0¼ 25¼ 3¼ 45¼ #0021 #0022 #0023 #0041 #0042 #0043 9 35 45 55 65 75 85 95 5 1 115 120 125 1 135 1 145 1 Minimum boom angle (¼) for indicated length (no load) Maximum boom length (ft.) at 0¼ boom angle (no load) 12,0 12,0 12,0 (74) 12,0 12, 11,, 9,1 8,4 (61.5) 7,8 (59) 7,2 6,6 (54) 6,1 (51) 5,6 5,020 (45.5) 4,3 (42.5) 3,7 (39.5) 3,2 (36) 2,720 (32) 2,2 (27.5) 1,8 (22) *,8,4 (77),000 9,220 (72.5) 8,5 (.5) 7,9 7,3 6,0 6,4 (.5) 6,0 5,720 (55.5) 5,0 (52.5) 5, (49.5) 4,7 (46.5) 4,1 (43) 3,0 (39.5) 3, (35) 2,6 (.5) *7,4 7,200 6,9 6,0 (72.5) 6,6 (.5) 6,4 6,3 6,1 (62.5) 5,7 5,4 (57) 5,200 (54) 4,9 (51) 4,6 (47.5) *8,3 8,3 8,3 8,3 8,2 (73) 7,5 7,1 6,820 (67.5) 6,0 5,8 5,3 (61.5) 4,9 4,6 (57) 4,320 (55) 4,0 (52.5) 3,7 (.5) 3,5 (48) 3,0 (45.5) 2,8 (42.5) 2,4 (39.5) 2,1 (36.5) 1,7 (33) 1,4 (29.5) 1,1 (25) *5,0 5,1 (77) 5, 5, (73) 4,0 4,5 4,4 (67.5) 4,3 4,0 3,8 (61) 3,620 (58.5) 3,4 (56) 3,2 (53.5) 3,0 (51) 2,8 2,7 (45.5) 2,5 (42.5) 2,2 (38.5) 1,8 (34.5) *3,8 3,7 3,6 3,5 (73) 3,4 3,4 3,0 (66.5) 3,2 (64) 3,220 (62) 3,1 3,0 2,9 (53.5) 2,0 (.5) 21 25 45 25 28 45 NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. 33 ft. and 56 ft. boom extension lengths may be used for single line lifting service. 3. Radii listed are for a fully extended boom with the boom extension erected. For main boom lengths less than fully extended, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom angle. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 5. Capacities listed are with outriggers fully extended and vertical jacks set only. NOTE: ( ) Boom angles are in degrees. A6-829-1289 #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based upon maximum boom angle. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
working range Working range 1 ft. Main Boom, Bi-Fold Swingaway & 20 ft. & ft. Inserts H [ft] 2 220 2 25 0 56' EXT. 200 45 1 33' EXT. 1 1 1 1 Height from the ground in feet 1 1 120 1 1 Boom and extension length in feet 20 36 20 0 78 MAX. BOOM ANGLE 0 200 1 1 1 1 1 1 1 120 1 20 Operating radius in feet from axis of rotation R [ft] AXIS OF ROTATION 8'-3" 8'-8" Dimensions are for largest Grove furnished hook block and headache ball, with anti-two block activated. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
load chart 36-1 ft. 33-56ft. 20 ft insert 12,1 lbs % 3¼ 23 ft. 4 in.spread 35 45 55 65 75 85 95 5 1 115 120 125 1 135 1 145 0 Pounds 33 ft. LENGTH 56 ft. LENGTH 25 45 0 25 45 #0064 #0065 #0066 #0084 #0085 #0086 *9,3 9,3 (77) 8,4 (75.5) 7,6 6,9 (71.5) 6,3 5,8 5,3 4,9 (64) 4,6 (62) 4,0 4,000 3,7 (55.5) 3,5 (53.5) 3,2 (51) 3,0 2,8 (46) 2,7 (43.5) 2,5 (.5) 2,2 (37.5) 1,8 (34.5) 1,5 (.5) 1,200 (26.5) *7,4 7,0 6,4 5,9 (74) 5,5 5,0 4,7 4,0 4,1 (64) 3,8 (62) 3,6 3,4 (57.5) 3,2 (55) 3,020 (52.5) 2,8 () 2,7 (47) 2,5 (44) 2,4 (41) 2,1 (37.5) 1,7 (34) *5,8 5,8 5,4 5,0 4,7 (72.5) 4,4 (.5) 4,1 3,8 3,6 (64) 3,0 (61.5) 3,0 3, (57) 2,9 (54.5) 2,7 (51.5) *6,0 6,0 6,000 5,9 5,9 5,5 5,0 4,5 4,1 (67) 3,820 (65) 3,520 3,220 (61.5) 2,9 2,7 2,5 (56) 2,3 (54) 2,1 (52) 2,000 () 1,8 (48) 1,720 (45.5) 1,6 (43) *4,8 4,8 4,4 4,0 3,8 (73) 3,5 3,320 (69.5) 3,0 (67.5) 2,8 2,6 (64) 2,4 (62) 2,2 2,1 1,9 (55.5) 1,8 (53.5) 1,7 (51) 1,6 1,520 (46) *3,7 3,4 3,2 2,9 (73) 2,7 2,5 2,4 (67) 2,3 (65) 2,200 2,0 (.5) 1,9 (58.5) 1,8 (56) 1,6 (53.5) 1,3 1 (43) Minimum boom angle ( ) for indicated length 20 25 45 41 45 (no load) Maximum boom length (ft.) at 0 boom angle (no load) NOTE: ( ) Boom angles are in degrees. A6-829-1371A #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based upon maximum boom angle. NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. 33 ft. and 56 ft. boom extension lengths may be used for single line lifting service only. 3. For main boom lengths less than 1 ft. with the boom extension erected, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is set up. For boom angles not shown, use rating of the next lower boom angle. 4. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 5. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 6. Capacities listed are with outriggers fully extended and vertical jacks set only. 11
load chart 12 36-1 ft. 33-56ft. ft insert 12,1 lbs % 3¼ 23 ft. 4 in.spread Pounds 33 ft. LENGTH 56 ft. LENGTH 45 55 65 75 85 95 5 1 115 120 125 1 135 1 0 25 45 0 25 45 #0064 #0065 #0066 #0084 #0085 #0086 6,5 5,9 5,3 4,8 (73) 4,3 3,9 (69.5) 3,6 (67.5) 3,2 2,9 (64) 2,7 (62.5) 2,4 (.5) 2,2 (58.5) 2,0 1,0 (54.5) 1,0 (52.5) 1,0 (.5) 1,4 (48) 1,3 (46) 1,120 (43.5) 1,0 (41) 5,8 5,2 4,8 4,3 (73) 4,0 (71.5) 3,6 (69.5) 3,3 3,0 2,8 (64) 2,5 (62) 2,3 2,1 2,000 (56) 1,0 (54) 1,0 (51.5) 1,5 (49.5) 1,420 (47) 1,220 (44.5) *5,1 4,6 4,2 (75.5) 3,9 3,6 3,3 3,0 2,8 2,6 (64) 2,3 (62) 2,200 2, 1,9 (55.5) 1,7 (53) 1,520 (.5) 1,420 (48) 4,5 4,2 3,9 3,7 3,4 (73) 3,220 (71.5) 2,820 2,520 2,320 (66.5) 2,0 (65) 1,8 1,6 (62) 1,4 1,2 (58.5) 1,1 (57) *3,7 3,420 3,120 2,820 2,620 (72.5) 2,3 2,1 (69.5) 1,9 1,7 1,5 (64.5) 1,3 (62.5) 1,2 (61) 1,0 (59) 2,7 2,5 2,3 2,1 (72.5) 1,9 1,7 1,5 (67) 1,4 (65) 1,2 1,1 (61.5) 1,1 145 (41.5) 1 1,0 (38.5) No Load Stability Data Min. boom angle at 1' 37 37 45 54 56 58 boom length Max. boom length at 0 boom angle ft. ft. NOTE: ( ) Boom angles are in degrees. A6-829-1581 NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. 33 ft. and 56 ft. boom extension lengths may be used for single line lifting service only. 3. For main boom lengths less than 1 ft. with the boom extension erected, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is set up. For boom angles not shown, use rating of the next lower boom angle. 4. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 5. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 6. Capacities listed are with outriggers fully extended and vertical jacks set only. *This capacity is based upon maximum boom angle. #LMI operating code. Refer to LMI manual for instructions. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
load charts 36- ft. 12,1 lbs Stationary 3¼ 12 15 20 25 35 45 Boom Angle Pounds Main Boom Length in 36 * 45,0 41,7 29,3 17,0 (49) 11,7 (36) 8,1 0 (29.7) Note: ( ) Reference radii in feet. 39,0 39,0 26,4 17,6 (55) 11,0 8,0 (31.5) 29,0 26,4 17,0 11,3 7,820 5,0 () 3,6 (28) Main Boom Length in 36 5,8 (34.2) #05 Lifting Capacities at Zero Degree Boom Angle On Rubber - Stationary 3 2,1 (44.2) #LMI operating code. Refer to LMI manual for instructions. * ft. boom length is with inner-mid extended and outer-mid & fly retracted. 20,0 (74) 16,2,8 7,4 (57.5) 5,120 (51.5) 3,200 1,000 (37) 16,2,8 7,4 5,120 3,4 (53) 2,1 (47.5) 1,1 (41.0) A6-829-48A 36- ft. 12,1 lbs Stationary Defined Arc Over Front 12 15 20 25 35 45 55 Boom Angle #05 Pounds Main Boom Length in 36 * 45,0 43,6 38,0 31,1 (49) 24, (36) 42,8 41,3 36,0 29,5 (55) 24,1 17,0 (31.5) 29,0 29,0 29,0 25,0 21,0 17,200 12,0 () 9,720 (28) Lifting Capacities at Zero Degree Boom Angle On Rubber - Defined Arc Over Front 17,0 0 (29.7) Note: ( ) Reference radii in feet. 20,0 (74) 20,0 18,0 15,0 (57.5) 12,0 (51.5) 9,3 7,0 (37) 5,3 (26.5) 17,0 17,0 17,0 15,0 11,000 9,3 (53) 7,0 (47.5) 5,3 (41) 3,8 (33.5) 3,1 (24) Main Boom Length in 36 * 13,0 (34.2) 7,7 (44.2) #LMI operating code. Refer to LMI manual for instructions. * ft. boom length is with inner-mid extended and outer-mid & fly retracted. 4,0 (54.6) 2,6 (64.2) A6-829-47 13
load charts 14 36- ft. 12,1 lbs Pick & Carry Boom Center Up to 2.5 mph Over Front 12 15 20 25 35 45 55 Boom Angle Pounds Main Boom Length in 36 * 42,0 42,0 37,0 32,9 (49) 24, (36) 17,0 0 (29.7) Note: ( ) Reference radii in feet. 37,0 37,0 37,0 32,0 (55) 24,1 17,0 (31.5),0,0,0,0 23,8 17,200 12,0 () 9,720 (28) 23,4 (77) 19,0 (74) 19,0 19,0 16,0 (57.5) 12,0 (51.5) 9,3 7,0 (37) 5,3 (26.5) 16,2 16,2 16,2 16,2 12,0 9,3 (53) 7,0 (47.5) 5,3 (41) 3,8 (33.5) 3,0 (24) Main Boom Length in 36 * 13,0 (34.2) #06 Lifting Capacities at Zero Degree Boom Angle On Rubber - Pick & Carry 7,7 (44.2) #LMI operating code. Refer to LMI manual for instructions. * ft. boom length is with inner-mid extended and outer-mid & fly retracted. 4,0 (54.6) 2,6 (64.2) A6-829-49 NOTES: 1. Capacities are in pounds and do not exceed 75% of tipping loads as determined by test in accordance with SAE J765. 2. Capacities are applicable to machines equipped with 29.6x25 (28 ply) tires at 65 psi cold inflation pressure. 3. Defined Arc Over front includes 6 on either side of longitudinal centerline of machine (ref. drawing C6-829-003529). 4. Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon as a capacity limitation. 5. Capacities are applicable only with machine on firm level surface. 6. On rubber lifting with boom extensions not permitted. 7. For pick and carry operation, boom must be centered over front of machine, mechanical swing lock engaged and load restrained from swinging. When handling loads in the structural range with capacities close to maximum ratings, travel should be reduced to creep speeds. 8. Axle lockouts must be functioning when lifting on rubber. 9. All lifting depends on proper tire inflation, capacity and condition. Capacities must be reduced for lower tire inflation pressures. See lifting capacity chart for tire used. Damaged tires are hazardous to safe operation of crane.. Creep Not over 200 ft. of movement in any minute period and not exceeding 1 mph. RIGGING CHART INSTALLATION AND REMOVAL OF 12,000 LB. COUNTERWEIGHT ON OUTRIGGERS FULLY EXTENDED 12 15 20 25 #01 Main Boom Length in *36 (49) (36) NOTE: ( ) Boom angles are in degrees. #LMI operating code. Refer to LMI manual for operating instructions. Boom Angle 0 (55) (31.5) Main Boom Length in *36 (29.8) NOTE: ( ) Reference radii in feet. *Boom must be fully retracted. (34.2) A6-829-2134
load handling Weight Reductions for Load Handling Devices 33 FT. - 56 FT. FOLDING BOOM EXTENSION *33 ft. Extension (Erected) - 5,0 lb. *56 ft. Extension (Erected) - 11,3 lb. FOLDING EXT. WITH 20 FT. INSERT 15 *33 ft. Extension (Erected) - 11,248 lb. *56 ft. Extension (Erected) - 19,372 lb. FOLDING EXT. WITH FT. INSERT *33 ft. Extension (Erected) - 19,671 lb. *56 ft. Extension (Erected) - 29,671 lb. *Reduction of main boom capacities (no deduct required for stowed boom extension) Line Pulls and Reeving Information When lifting over swingaway and/or jib combinations, deduct total weight of all load handling devices reeved over main boom nose directly from swingaway or jib capacity. NOTE: All load handling devices and boom attachments are considered part of the load and suitable allowances MUST BE MADE for their combined weights. Weights are for Grove furnished equipment. AUXILIARY BOOM NOSE 137 lb. HOOKBLOCKS and HEADACHE BALLS: Ton, 5 Sheave 12 lb.+ Ton, 4 Sheave 0 lb.+ Ton, 3 Sheave 0 lb.+ 8.3 Ton Headache Ball (non-swivel) 3 lb.+ 8.3 Ton Headache Ball (swivel) 3 lb.+ +Refer to rating plate for actual weight. Line Pulls and Reeving Information Permissible Nominal Hoists Cable Specs Line Pulls Cable Length 3/4" (19 mm) 6x37 Class, Main EIPS, IWRC Special Flexible 16,0 lb. 0 ft. Min. Breaking Str. 58,0 lb. 3/4" (19 mm) Flex-X 35 Main & Aux. Rotation Resistant (non-rotating) 16,0 lb. 0 ft. Min. Breaking Strength 85,0 lb. The approximate weight of 3/4" wire rope is 1.5 lb./ft. Hoist Performance Wire Hoist Line Pulls Drum Rope Rope Two Speed Hoist Capacity (ft.) Layer Low High 16 in. Drum 26 in. Drum Available lb.* Available lb.* Layer Total Layer Total 1 18,134 9,067 78 78 132 132 2 16,668 8,334 85 164 144 276 3 15,420 7,7 92 256 156 432 4 14,347 7,174 99 356 167 599 5 13,413 6,7 6 462 179 778 6 12,594 6,297 113 575 1 968 *Max. lifting capacity: 6x37 or 35x7 class = 16,0 lb. Working Area Diagram CENTERLINE OF BOOM 3 OVER SIDE CENTERLINE OF OUTRIGGER SUPPORT LONGITUDINAL CENTERLINE OF CRANE BOOM CENTERED OVER FRONT 3 REAR AXLE OSCILLATION LOCKOUTS MUST BE SET TO MAINTAIN 3 CAPACITIES CG OF LOAD OVER FRONT OVER REAR 12 6 SEE NOTE AT BOTTOM FRONT DIAGRAM FOR LIFTING ON OUTRIGGERS OVER SIDE CENTERLINE OF ROTATION DIAGRAM FOR LIFTING ON TIRES Bold lines determine the limiting position of any load for operation within working areas indicated. C6-829-003529 C6-829-001159 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Manitowoc Crane Group - Americas Manitowoc, Wisconsin Facility Tel: [Int + 001] 920 684 6621 Fax: [Int + 001] 920 683 6277 Shady Grove, Pennsylvania Facility Tel: [Int + 001] 717 597 8121 Fax: [Int + 001] 717 597 62 Manitowoc Crane Group - EMEA Europe Middle East & Africa Tel: [Int + 33] (0) 191 565 6281 Fax: [Int + 33] (0) 4 72 18 20 20 Manitowoc Crane Group - UK Europe Middle East & Africa Tel: [Int + 44] (0) 191 565 6281 Fax: [Int + 44] (0) 191 564 0442 Manitowoc Crane Group - Germany (Sales, Parts & Service) Tel: [Int + 49](0) 2173 89 0 Fax: [Int + 49] (0) 2173 89- Manitowoc Crane Group - France France & Africa (Sales, Parts & Service) Tel: [Int + 33] (0) 1 3 131 Fax: [Int + 33] (0) 1 3 885 Manitowoc Crane Group - Netherlands (Sales, Parts & Service) Tel: [Int + 31] (0) 76 578 39 99 Fax: [Int + 31] (0) 76 578 39 78 Manitowoc Crane Group - Italy Italy & Southern Europe (Sales, Parts & Service) Tel: [Int + 39] (0) 331 49 33 11 Fax: [Int + 39] (0) 331 49 33 Manitowoc Crane Group - Portugal Portugal & Spain (Sales, Parts & Service) Tel: [Int + 351] (0) 22 968 08 89 Fax: [Int + 351] (0) 22 968 08 97 Manitowoc Crane Group - Singapore Asia/Pacific excl China (Sales, Parts & Service) Tel: [Int + 65] 6861 1733 Fax: [Int + 65] 6862 / 4142 Manitowoc Crane Group - Shanghai China (Sales, Parts & Service) Tel: [Int + 86] (0) 21 64955555 Fax: [Int + 86] (0) 2164852038 Manitowoc Crane Group - Beijing China (Sales, Parts & Service) Tel: [Int + 86] (0) 646 716 Fax: [Int + 86] (0) 646 71691 Manitowoc Crane Group - Middle East Sales Tel: [Int + 971] (0) 4 348 4478 Fax: [Int + 971] (0) 4 348 4478 (Parts & Service) Tel: [Int + 973] (0) 9 6 899 Fax: [Int + 973] (0) 2 7 7 Distributed By: Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment, and price changes without notice. Illustrations shown may include optional equipment and accessories, and may not include all standard equipment. www.manitowoccranegroup.com 04-2M Printed in USA Form No. PG Part No. 03-474 Manitowoc Crane Group 2003