Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 50W Slim Type with PFC Switching Power Supply GB494 UL950-1 EN950-1 EN5-1 IEC950-1 - ~ Industrial automation machinery Industrial control system Mechanical and electrical equipment Electronic instruments, equipments or apparatus Household appliances LED display application ; R
SPECIFICATION MODEL OUTPUT INPUT PROTECTION DC VOLTAGE RATED CURRENT.V A 4.2V A 5V A 12V 29.2A 15V 2.4A 24V 14.6A 6V 9.75A 48V 7.A RATED POWER(convection) 198W 252W 00W 50.4W 51W 50.4W 51W 50.4W RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p 200mVp-p 200mVp-p 200mVp-p 2mVp-p 2mVp-p 2mVp-p VOLTAGE ADJ. RANGE.2~.5V.6~4.4V 4.5~5.5V 11.4~12.6V 14.~15.8V 22.8~25.2V 4.2~7.8V 45.6~50.4V VOLTAGE TOLERANCE Note. ±2.0% ±2.0% ±2.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.% ±0.% ±0.% ±0.% ±0.% LOAD REGULATION ±1.0% ±1.0% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% SETUP, RISE TIME 2000ms, ms/20vac 000ms, ms/115vac at full load HOLD UP TIME (Typ.) 10ms/20VAC 10ms/115VAC VOLTAGE RANGE Note.4 90 ~ 264VAC 127 ~ 70VDC FREQUENCY RANGE 47 ~ 6Hz POWER FACTOR (Typ.) PF 0.94/20VAC PF 0.98/115VAC at full load EFFICIENCY (Typ.) 88.5% 89% 90% 91% 92% 94% 94% 94% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVERLOAD OVER VOLTAGE OVER TEMPERATURE DC OK SIGNAL(Optional) UHP-50 -. UHP-50-4.2 UHP-50-5 UHP-50-12 UHP-50-15 UHP-50-24 UHP-50-6 UHP-50-48 4A/115VAC Cold start 0A/115VAC <0.75mA / 2VAC 2A/20VAC 110~1% rated output power A/20VAC Protection type : Hiccup mode, recovers automatically after fault condition is removed.8 ~ 4.6V 4.62 ~ 5.46V 5.75 ~ 6.75V 1.2 ~ 15.6V 16.5 ~ 19.5V 26.4 ~ 1.2V 9.6 ~46.8V 52.8 ~ 62.4V Protection type :Shut down O/P voltage,re-power on to recover Protection type :Shut down O/P voltage, recovers automatically after temperature goes down Contact rating(max.):15vdc/10ma resistive load FUNCTION REDUNDANT(Optional) For parallel connection protection:for parallel applications, when one PSU can not work, the another one will be automatically enabled. This can prevent the system crash, and provide the reliability of system WORKING TEMP. WORKING HUMIDITY -0 ~ +70 (Refer to Derating Curve") 20 ~ 90% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY - ~ +85, 10 ~ 95% RH non-condensing TEMP. COEFFICIENT VIBRATION ± 0.0%/ (0 ~ 50 ) 10 ~ 500Hz, 5G 10min./1cycle, min. each along X, Y, Z axes SAFETY STANDARDS UL950-1,TUV EN950-1,EN5-1,CCC GB494, EAC TP TC 004 approved,design refer to EN61558-1,-2-16 WITHSTAND VOLTAGE SAFETY & I/P-O/P:.75KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG,O/P-FG:M Ohms/500VDC/25 / 70%RH (Note.6) EMC EMISSION Compliance to EN5502,GB9254,Class B, EN55014,EN--2,-,EAC TP TC 020 EMC IMMUNITY Compliance to EN-4-2,,4,5,6,8,11;EN-6-2 (EN50082-2), heavy industry level,criterial A,EAC TP TC 020 MTBF 285 K hrs min. MIL-HDBK-217F (25 ) OTHERS DIMENSION 220*62*1mm (L*W*H) NOTE PACKING 0.68 kg;16 pcs/11.88 kg/0.6cuft
Block Diagram I/P EMI FILTER & RECTIFIER PFC CIRCUIT POWER SWITCH- ING RECTIFIERS & FILTER FG O.T.P. O.L.P. CONTROL DETECTION CIRCUIT O.V.P. DC OK Function Redundant Function Derating Curve 20Vac for.v~5v 20Vac for 12V~48V RATED CURRENT (%) 20 RATED CURRENT (%) 70 20 110Vac for all model -0 0 10 20 0 50 70 (HORIZONTAL) -20 0 10 20 0 50 70 (HORIZONTAL) AMBIENT TEMPERATURE ( ) AMBIENT TEMPERATURE WITHOUT ALUMINUM PLATE( ) RATED CURRENT (%) 20-0 0 10 20 0 50 70 90 (HORIZONTAL) Tcase ( )
STATIC CHARACTERISTIC 90 LOAD (%) 70 50 90 110 120 1 1 1 200 220 2 264 INPUT VOLTAGE (V) Hz Function Manual 1.DC_OK Signal DC_OK is a collector shorted signal. It is used by an optocoupler in the power supply which indicates the output status of the power supply as exhibited below. DC OK 1K Optocoupler C-E Pin Conduction PSU turns on DC ok C E Optocoupler C-E Pin Open Optocoupler Rating(max.) PSU turns off DC fail 15Vdc/10mA resistive load GND PSU COM 2.Redundant function (1) UHP-50R is built-in redundant function and can be connected 2 units in parallel. (2) When in parallel operation the maximum load should not be greater than the rated power of any PSU. PSU LOAD PSU
Mechanical Specification CASE NO.:22C Unit:mm 220 214 7.8 1 2 7.62 TB1 2 1 TB TB2 1 2 4 10.9 8.5 9.25 46.4 62 CN10 SVR 4-ψ. L=6 110 15.5 tc 1 tc : Max. Case Temperature AC Input Terminal(TB1) pin NO. Assignment DC Output Terminal(TB2,TB) pin NO. Assignment Pin No. Assignment Terminal Max mounting torque Pin No. Assignment Terminal Max mounting torque 1 AC/L (DEGSON) 1,2 (MW) 2 AC/N DG28C-B-0P 5Kgf-cm,4 TB-HTP-200-A 8Kgf-cm DC OK Connector(CN10):JST B2B-PH-K-S or requivalent Mating Housing Terminal Pin No. 1 2 Assignment DC COM DC OK JST PHR-2 or requivalent JST SPH-002T-P0.5S or requivalent
Installation 1.Operate with additional aluminum plate In order to meet the Derating Curve and the Static Characteristics, must be installed onto an aluminum plate(or the cabinet of the same size) on the bottom.the size of the suggested aluminum plate is shown as below. And for optimizing thermal performance, the aluminum plate must have an even and smooth surface (or coated with thermal grease), and must be firmly mounted at the center of the aluminum plate. unit:mm 450 M*4 450