INSTLLTION INSTRUCTIONS FOR PRT 99-7608 PPLICTIONS Nissan Cube 009 99-7608 KIT FETURES DIN Head Unit Provision with Pocket ISO DIN Head Unit Provision with Pocket Double DIN Head Unit Provision KIT COMPONENTS ) Radio Housing ) ISO rackets C) Trim Plate D) Double DIN Trim Plate C D WIRING ND NTENN CONNECTIONS (Sold Separately) Harness: 70-755 - Nissan harness 007-up ntenna dapter: 40-NI - Nissan antenna adapter 007-up TOOLS REQUIRED: Small Flat lade Screwdriver/ Panel Removal Tool Phillips Screwdriver -800--093 www.metraonline.com COPYRIGHT 009 METR ELECTRONICS CORPORTION
99-7608 Dash Disassembly TLE OF CONTENTS - Nissan Cube 009......... Kit ssembly - DIN Head Unit Provision with Pocket.......................... - ISO Head Unit Provision with Pocket.......................... 3 - Double DIN Head Unit Provision............................. 4 Final ssembly...........................................5 Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-678 for more information and take steps toward a better tomorrow.
99-7608 DSH DISSSEMLY NISSN CUE 009 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove () Phillips screws from the bottom of the a/c trim panel then unclip and remove the panel. (Figure,) /C 3 Remove () Phillips screws from the bottom of the radio trim panel then unclip and remove the panel. (Figure C) 4 Remove (4) Phillips screws securing radio to dash to remove. C
99-7608 KIT SSEMLY DIN HED UNIT PROVISION WITH POCKET Note: Refer also to the instructions included with the aftermarket radio. Note: The DIN trim plate and DDIN trim plate have supports in the middle that can be removed with cutters and trimmed with a knife if necessary. Note:The aftermarket radio s trim plate must be removed prior to installation. Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure ) 3 Slide the aftermarket head unit into the cage and secure. (Figure ) ttach the trim plate supplied with the kit. (Figure ) Continue to final assembly.
99-7608 KIT SSEMLY ISO DIN HED PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. Mount the ISO rackets to the head unit with the screws supplied with the unit. (Figure ) Slide the head unit into the radio opening until the side clips engage. (Figure ) 3 ttach the trim plate supplied with the kit. (Figure ) Continue to final assembly. 3
99-7608 KIT SSEMLY DOULE DIN HED UNIT PROVISION *Note: Refer also to the instructions included with the aftermarket radio. Slide the DDIN radio unit into the factory brackets and secure the unit to the brackets using the screws supplied with the head unit. (Figure ) Place the DDIN trim plate over the face of the aftermarket radio or into the opening of the OE radio bezel prior to final assembly. (Figure ) Continue to final assembly. 4
99-7608 FINL SSEMLY FINL SSEMLY C () Strip wire ends back /" ) Twist ends together C) Solder D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING CONNECTIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METR / EI WIRING CODE V Ignition / cc.......... Red V att / Memory......... Yellow Ground.................. lack* Power ntenna............ lue mp Turn-On............. lue / White mp Ground.............. lack / White Illumination.............. Orange Dimmer................. Orange / White Right Front (+)............ Gray Right Front (-)............. Gray/ lack Left Front (+)............. White Left Front (-).............. White / lack Right Rear (+)............ Violet Right Rear (-)............. Violet / lack Left Rear (+)............. Green Left Rear (-).............. Green / lack *NOTE: When a lack wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. 5
99-7608 INSTRUCTIONS -800--093 www.metraonline.com REV. 07/8/09 COPYRIGHT 009 METR ELECTRONICS CORPORTION INST99-7608