Secoroc Rock Drilling Tools SECOROC MAGNUM SR AND TC EQUIPMENT For bench drilling
SECOROC MAGNUM SR AND SECOROC TC breaking the surface Since the advent of Secoroc Magnum SR35, this range of patented threaded drill systems have expanded with new applications. Now, two Magnum SR and one TC can be found above ground working on construction and bench drilling. More material where it s needed Thanks to these patented conical threaded systems, we re confident that rod breakage is a problem you will see a lot less of. Because there is more material at the rod end - hence the distinctive conical shape - we ve successfully strengthened the product, while minimizing any tendency to deviate during collaring. The result? Straighter holes and a much longer service life. The common denominator for both systems is that they offer thicker and stronger rods with the same bit diameters as the equivalent R or T threaded system. The result is less downtime, straighter holes and better productivity. And as an extra bonus, rods and bits are much easier to couple and uncouple. 2
Made to match the FlexiRoc drilling rigs The FlexiRoc T15 and T20 are a range of remote controlled tophammer drilling rigs that regularly operate on construction and bench drilling sites. They needed to find new and appropriate drillstring solutions to match and found it in the Magnum SR28, Magnum SR32 and the TC35. This group of drill strings cover holes from 33 mm to 64 mm and offer unique drilling qualities. Secoroc TC35 Fits the FlexiRoc T20 The TC35 matches the FlexiRoc T20 perfectly, working on construction or bench drilling sites. Replacing the R32 system, this 48-64 mm diameter drill system is quite an all rounder. Despite being more robust than the R32, the TC35 still offers an equivalent range of drill sizes, though this time, with minimal bending tendency and maximal longevity. And thanks to this trapezoidal conical system, the TC35 can use 51 mm extension drilling equipment such as round Speedrods and retrac button bits. They are ideal in urban housing areas, for example, where stringent restrictions on vibration and noise have been set. Quite simply, the combination of TC35 and 51mm extension equipment means faster drilling, larger blast areas and minimal disturbance to the surroundings. Magnum SR32 Ideal for FlexiRoc T15 The FlexiRoc T15, a size smaller than the T20, is ideal for those tight urban construction sites. Here, the Magnum SR32 can drill holes from 38-48 mm using hexagonal or round Speedrods and a choice of three button bits designs. In fact, SR32 drill rods are stronger and thicker that the equivalent R28 drills. Magnum SR28 Extension or shank end rods The Magnum SR28, the smallest of these three models, has a hole range from 33-45 mm in diameter using shank end rods or single pass Speedrods. If you prefer extension rod systems then you can drill holes as small as 41-45 mm by using hexagonal Speedrods. There is also a choice of the five drill bits designs four button bits and one cross type enabling FlexiRoc T15 to operate productively in difficult areas. Even though the R25 drill system offers the same size of drill holes, the Magnum SR28 offers more with its conical threads, its robust rods and long service life. 3
SR28 (1 1 8") Magnum SR28 thread system 33 % more material means a substantial increase in metal fatigue resistance 28 mm (1 1 8") diameter thread 25 mm (1") diameter thread Conical shaped rope thread facilitates rapid coupling and uncoupling More material between skirt and bit head Magnum SR28 drill string Shank end rod Button bit Shank adapter Hex. Speedrod Cross-type bit Dome reaming bit Drill bits -5033-17 -5xxx-27-5xxx-37-67 -5xxx-41 Cross-type bit -5076-42-24 Buttons button meter No. of Buttons angle hole Product No. Product code diameter (mm) approx. buttons mm inch Gauge Centre Gauge Centre Side Centre kg BUTTON BIT - Spherical buttons 33 1 5 16 90514200 125-5033-17,39-20 7 5 7 2 7 35 1 1 0,4 33 1 5 16 90514117 125-5033-41,39-20 7 5 8 2 7 40 15 1 1 0,4 35 1 3 8 90514322 125-5035-27,39-20 7 5 9 2 7 25 10 1 1 0,4 38 1½ 90514282 125-5038-27,39-20 7 5 9 2 7 30 1 1 0,5 41 1 5 8 90515379 125-5041-27,39-20 7 5 9 2 8 40 1 1 0,7 45 1 3 4 90514507 125-5045-27,39-20 7 5 11 2 8 30 2 1 0,9 4
SR28 (1 1 8") Buttons button meter No. of Buttons angle hole Product No. Product code diameter (mm) approx. buttons mm inch Gauge Centre Gauge Centre Side Centre kg BUTTON BIT - Ballistic buttons 33 1 5 16 90514137 125-5033-41-67,39-20 7 5 8 2 7 40 15 1 1 0,4 35 1 3 8 90514102 125-5035-27-67,39-20 7 5 9 2 7 25 10 1 1 0,4 38 1½ 90516334 125-5038-41-67,39-20 7 5 9 2 8 40 20 1 1 0,5 41 1 5 8 90516383 125-5041-37-67,39-20 9 6 9 3 7 40 3 0,5 45 1 3 4 90516422 125-5045-37-67,39-20 9 6 9 3 8 40 3 0,7 CROSS-TYPE BIT 33 1 5 16 90514429 125-7033-44,20-17 10,3 19,5 2 1 0,5 35 1 3 8 90516590 125-7035-44,20-17 10,3 19,5 2 1 0,5 DOME BIT - Spherical buttons 76 3 90515258 125-5076-42-24,49-20* 10 9 12,7 1 12,7 35 1 3 2,0 * For reaming, reversed flushing. Width (mm) Insert Height (mm) Speedrod SR28 (1 1 8") Hex. 25 mm (1") SR28 (1 1 8") Fully carburized (C). D = 34 mm. Rod section 28,5 mm. hole diameter 8,6 mm. mm ength () foot Product No. Product code 3050 10 90516350 225-0331-69-MF-C,02 12,1 Shank end rods Fully carburized. hole diameter 8,6 mm. ength () mm foot inch Product No. Product code Seal Product No. Seal Product code Shank hex. 25 mm (1") 108 mm (4¼"). 28 mm (1 1 8") thread. 265 10 3 8" 90516367 525-1103-C,02 1,7 3660 12' 90516330 525-1237-C,02 90000373 9150-08 15,2 5
SR32 (1¼") Magnum SR32 thread system 30 % more material means a substantial increase in metal fatigue resistance 32 mm (1¼") diameter thread 28 mm (1 1 8") diameter thread Conical shaped rope thread facilitates rapid coupling and uncoupling More material between skirt and bit head Magnum SR32 drill string Shank adapter Round Speedrod Button bit 6
SR32 (1¼") Drill bits -5xxx-27-67 -5xxx-37-67 Buttons button meter Gauge No. of hole Product No. Product code diameter (mm) buttons buttons mm inch Gauge Centre angle Side Centre BUTTON BIT - Ballistic buttons 38 1½ 90514501 126-5038-27-67,39-20 7 5 9 2 7 40 1 1 0,5 41 1 5 8 90516483 126-5041-37-67,39-20 9 6 9 3 7 40 3 0,5 43 1 11 16 90516484 126-5043-37-67,39-20 9 6 9 3 7 40 3 0,6 45 1¾ 90514953 126-5045-37-67,39-20 9 6 9 3 8 40 1 3 0,7 48 1 7 8 90515721 126-5048-37-67,39-20 9 6 10 3 9 40 1 3 0,9 Speedrods SR32 (1¼") Round 32 mm (1¼") SR32 (1¼") Fully carburized (C). D = 38 mm. hole diameter 11,7 mm. mm ength () foot inch Product No. Product code 1830 6' 90003686 226-4518-69-MF-C,02 11,7 3090 10'1 5 8" 90516482 226-4531-69-MF-C,02 18,5 7
TC35 (1 3 8") TC35 thread system 30 % more material means a substantial increase in metal fatigue resistance 35 mm (1 3 8") diameter thread 32 mm (1¼") diameter thread Conical shaped T-thread facilitates rapid coupling and uncoupling More material between skirt and bit head TC35 drill string Shank adapter Round Speedrod Button bit Retrac button bit 8
TC35 (1 3 8") Drill bits -5048-37-67-6xxx-45-67 -6054-67 -6064-48-45-67 Buttons button meter Gauge No. of hole Product No. Product code diameter (mm) buttons buttons mm inch Gauge Centre angle Side Centre approx. kg BUTTON BIT - Ballistic buttons 48 1 7 / 8 90516336 169-5048-37-67,39-20 9 6 10 3 9 40 1 3 1,0 51 2 90516337 169-6051-45-67,49-20 9 6 10 3 9 35 3 1,2 54 2 1 / 8 90516564 169-6054-67,39-20 9 6 10 3 9, 1x7 40 3 1,0 54 2 1 / 8 90516423 169-6054-45-67,49-20 9 6x11 3x9 40 3 1,3 57 2 1 / 4 90516536 169-6057-45-67,39-20 9 6x11 3x9 40 3 1,5 64 2 1 / 2 90516424 169-6064-48-45-67,49-20 13 8x10 4x10, 1x7 35 4 2,0 Speedrods TC35 (1 3 8") Round 39 mm (1 17 32") TC35 (1 3 8") Fully carburized (C). D = 46 mm. hole diameter 14,5 mm. mm ength () foot Product No. Product code 2435 8 90003646 269-4724-MF-C,02 19,7 3050 10 90003577 269-4731-MF-C,02 24,7 3660 12 90003578 269-4737-MF-C,02 29,6 4270 14 90003579 269-4743-MF-C,02 34,6 9
Shank adapters Atlas Copco COP 1028 Ø33 55 ength () mm SR28 (1 1 8") 90515870 425-07202,10 400 45 2,7 SR32 (1¼") 90516485 426-07202,10 400 45 2,8 Atlas Copco COP 1032 Ø54 58,5 ength () mm TC35 (1 3 8") 90516340 469-02006,10 510 45 4,9 Atlas Copco COP 1036, COP 1038, COP 1238 Ø54 74 ength () mm TC35 (1 3 8") 90516341 469-03003-13,10 575 45 5,4 Atlas Copco COP 1132 Ø38 79 ength () mm SR32 (1¼") 90516637 426-15701,10 410 35 2,5 TC35 (1 3 8") 90516636 469-15701,10 410 35 2,5 Atlas Copco COP 1132 Ø38 79 ength () mm SR28 (1 1 8") 90515872 425-15704,10 500 35 2,8 SR32 (1¼") 90516570 426-15704,10 500 35 3,0 TC35 (1 3 8") 90516598 469-15704,10 500 35 3,0 Atlas Copco COP 1140 Ø38 79 ength () mm SR32 (1¼") 90003559 426-19001,10 410 35 2,5 TC35 (1 3 8") 90003555 469-19001,10 410 35 2,6 10
Shank adapters Atlas Copco COP 1240, COP 1640 Ø54 124,5 ength () mm TC35 (1 3 8") 90516343 469-13302,10 565 52 6,4 Atlas Copco COP 1440, COP 1550, COP 1838 Ø54 84,5 ength () mm TC35 (1 3 8") 90516342 469-09103-18,10 525 52 5,8 Atlas Copco COP 1838 Ø54 84,5 ength () mm TC35 (1 3 8") 90516393 469-09103,10 525 38 4,2 11
We stand by our responsibilities towards our customers, towards the environment and the people around us. We make performance stand the test of time. This is what we call - Sustainable Productivity. Atlas Copco Secoroc AB Box 521, SE-737 25 Fagersta, Sweden Phone: +46 223 461 00 www.atlascopco.com 9851 2793 01 Subjected to alterations without prior notice. Atlas Copco Secoroc AB. All rights reserved. 2013.01