Wicked Warrior Tandem Utility Disc From aggressive tillage to no-ridge soil finishing, the Wicked Warrior is the answer. FEATURES The Wicked Warrior is the ideal choice for residential gardens, commercial landscaping, and food plot seedbed preparation. This three-point disc is sized for use with small horsepower tractors, and its true tandem design results in a smooth soil finish that s ready for seeding or sodding. The Wicked Warrior s smaller frame offers the same rugged build as all other AMCO products. Available in four cutting widths: 4', 5', 6', and 8' Main frame 2" x 3" square tubing with 3" x 3" cross braces 3 16" thick 18" x 16" standard cutout blades 3 Gang angle pin adjustable to offer aggressive tillage or soil finishing options Category I quick-hitch compatible
Below: Heavier-duty reinforced bearing risers offer extra bracing for durability. Left: Gang frames feature rugged 3" by 3" tubing, ¼" thick. Left: The true tandem design means no ridge where wings overlap, just perfectly finished soil. Right: The ability to easily add fresh grease to bearings helps ensure long-term dependability and protects from damage. Above: AMCO's 11 8" axle and locking nut give the Wicked Warrior an advantage over similar models with 1" axles. Left: Pin-adjustable gangs and components are locked in place by specially designed plates so less time is spent on adjustments. Model Cutting Width No. of Discs Approx. Engine Approx. HP Required Weight lbs WW-1218 4' 12 28 420 WW-1618 5' 16 35 742 WW-2018 6' 20 45 825 WW-2418 8' 24 55 1,290 Specifications subject to change without notice. Toll free: 800-748-9022 662-746-4464 Fax: 662-746-6825 Web: www.amcomfg.com Facebook: www.facebook.com/ AMCOManufacturingInc Email: sales@amcomfg.com TOUGH 1947 TILLAGE TOOLS SINCE 12/30/2014 Wicked Warrior Models (available in AMCO yellow or green) 800 S. Industrial Parkway P. O. Box 1107 Yazoo City, MS 39194
Protect-O-Shield Bearings Guaranteed for two full years. PROTECT-OSHIELD GREASE FITTING PROTECT-OSHIELD BEARING INNER RACE DUCTILE HOUSING FOR TOGGLE MOUNTING TRIPLE-LIP SEALS GREASE GROOVE LTF LIFT OFFSET HARROW Get the job done right the first time. Built AMCO tough, the rugged, hard-working LTF Lift Offset Harrows are perfect for building and maintaining food plots, logging roads, gardens, turn rows, firebreaks, and much more. Small-frame models fit category I or II hitches, while large-frame model gang angles are adjustable from 14" to 18" and fit category II or III hitches. FEATURES All sizes have the same quality features you have come to expect from all of our implements: Eight greaseable ball-type, toggle-mounted Protect-O-Shield Bearings, guaranteed for two full years (See above) 18" x ¼" cutout blades on small-frame harrows and 22" x ¼" cutout blades on large frame harrows High-carbon 1½" square axles High-carbon replaceable blades on heavyduty scrapers to keep blades free from debris (scrapers are not standard on small-frame models)
Left: Save time and energy with our optional broadcast seeder with bracket and dragboard kit. This is an easy way to plant and cover your seeds for the best results (2 x 8 board not included). Below: AMCO s Shock Absorbing Gang Risers allow the gang on the harrow to move upward and back to relieve shock when the disc blades encounter an obstacle in the ground. Above: Keep blades free from debris with our heavy-duty scrapers. Above: Our small-frame and large-frame sizes ensure that no matter the job, we have the right tool for you. Cutting Width No. of Discs Approx. Engine HP Required* Approx. Weight lbs LTF Models Small LTF100-1618 6' 16 32-47 1,600 LTF100-2018 7'3" 20 41-52 1,750 Large LTF100B-2022 7'3" 20 60 2,450 LTF100B-2422 8'7" 24 80 2,700 LTF100B-2822 10'2" 28 100 2,900 Pine Plantation LTFP100B-2022 7'3" 20 *Four-wheel drive recommended. Specifications subject to change without notice. 60 2,600 800 S. Industrial Parkway P. O. Box 1107 Yazoo City, MS 39194 Toll free: 800-748-9022 662-746-4464 Fax: 662-746-5466 Web: www.amcomfg.com Facebook: www.facebook.com/ AMCOManufacturingInc Email: sales@amcomfg.com TOUGH 1947 TILLAGE TOOLS SINCE 6/6/2014 Model
See back for more details F15 & C15 DOUBLE OFFSET TANDEM DISC HARROWS Create a berm-free seedbed with AMCO flexwings. F15 and C15 Double Offset Tandem Disc Harrows with folding flexwings to follow the contour of the field and utilize a double offset tandem design to smooth the soil. Overlapping front discs cut through soil and residue, while the flow of soil off the staggered rear disc gangs fills in the center furrow. This results in a more even performance and the perfect seedbed without the need for a shank to level off the center. Use the F15 and C15 for primary or secondary tillage, seedbed prep, or incorporation of chemicals. Turn them loose in your heavier primary tillage situations or to incorporate residue including residue from cover crops for faster breakdown. 12/30/2014 We offer different models for a wide range of operations. All are field-tested and proven tough: Model F15 9" spacing; 16'6", 18'0", 19'6", 21'0", 24'0", 27'0", 30'0", 34'6", and 39'0" cutting widths Model C15 7½" spacing; 24'0", 27'0", and 30'0" cutting widths
Left: Front-wing depth gauge wheels assist with controlled depth of the wings at higher operation speeds. TAKE A CLOSE LOOK: DOUBLE OFFSET TANDEM DISC HARROW FEATURES Left: Turnbuckle rod allows adjustments to ensure level cutting. Adapts to various tire sizes and provides a level transport. Below: Safety lights, SMV signage, and safety chain standard. Above: Double offset tandem design with diminishing blades in the center ensures dirt work is complete across the tool. Below: Transport stand with lockout pin to ensure safe road travel also standard. Left: 90-inch tongue features jack and adjustable clevis. Left: Mechanical DIAL-A-DEPTH gauge control arms ensure an even depth, providing more accuracy. Easily adjust cutting depth in the field with the 4 x 24 hydraulic cylinders (3,000 PSI). Right: Bearing risers for built-in durability. 24-inch smooth blades (22- and 26-inch blades also available) provide clean cutting through soil and residue. Other sizes available.
DOUBLE OFFSET TANDEM DISC HARROWS Cutting Width Transport Transport Transport Width Height Cylinder No. of Disc Blades No. of Bearings Approx. Engine HP Required Approx. Weight lbs. F15B-4622 16'6" 4" x 8" 46 16 155-176 6,705 F15B-5022 18'0" 4" x 8" 50 16 162-189 7,419 F15B-5422 19'6" 4" x 8" 54 16 169-203 7,623 F15B-5822 21'0" 4" x 8" 58 16 182-223 8,346 F15B-6622 24'0" 4" x 8" 66 20 202-243 9,306 F15-6624 24'0" 14'6" 11'0" 4"x 12" (center); 3½" x 12"(wing) 66 20 243-297 11,591 F15-7424 27'0" 14'6" 12'0" 4"x 12" (center); 3½" x 12"(wing) 74 22 243-297 12,283 F15-8224 30'0" 14'6" 13'3" 4"x 12" (center); 3½" x 12"(wing) 82 22 256-318 12,935 F15-9424 34'6" 17'6" 14'0" 4"x 12" (center); 3½" x 12"(wing) 94 26 310-378 15,423 F15-10624 39'0" 17'6" 15'9" 4"x 12" (center); 3½" x 12"(wing) 106 30 337-405 16,671 C15-8424 24'0" 14'6" 12'9" 4"x 12" (center); 3½" x 12"(wing) 84 20 243-297 13,016 C15-9424 27'0" 14'6" 13'9" 4"x 12" (center); 3½" x 12"(wing) 94 22 310-378 14,643 C15-10624 30'0" 14'6" 15' 1" 4"x 12" (center); 3½" x 12"(wing) 106 22 337-405 16,271 Model Models available to meet every need Workhorse Heavy Duty Giant Heavy Duty *Specifications for all models subject to change without notice. DOUBLE OFFSET TANDEM DISC HARROW OPTIONAL EQUIPMENT Shock Absorber Bearing Risers allow the gang on the harrow to travel up and down to relieve shock when the disc blades encounter an unexpected obstacle in the ground (available on all models) 15" x 10" 8-hole wheels and 8-hole hubs optional equipment on 66-blade, 74-blade, and 82-blade models (center section only) Heavy-duty wheels, heavy-duty scrapers, and cutout blades in place of standard smooth blades
Greasable ball-type, toggle-mounted Protect-O-Shield bearings, guaranteed for two full years (see below) 1½" square cold-rolled, high-carbon steel axles All models feature smooth blades with two feathering blades on the rear gangs Diminishing blades in the center of the double offset tandem design achieve a berm-free, level seedbed with no additional tools required 15" x 10" 8-hole wheels and 8-hole hubs standard equipment on 94-blade and 106-blade models (center section only) 90" tongue with jack enables sharper turns on dual-wheel tractors Scraper setup features heavy-duty arms, bars, and blades; blades are replaceable Hydraulic hoses complete to front of main frame Adjustable clevis of ductile iron with transport adapter Heavy-duty 3,000 PSI hydraulic cylinders to adjust cutting depth and raise the disc for transport DIAL-A-DEPTH depth control, allowing an even cut with positive depth control the entire width of the harrow AN UNBEATABLE COMBINATION FOR WORK IN ROUGH TERRAIN 800 S. Industrial Parkway P. O. Box 1107 Yazoo City, MS 39194 Toll free: 800-748-9022 662-746-4464 Fax: 662-746-6825 Web: www.amcomfg.com Facebook: www.facebook.com/ AMCOManufacturingInc Email: sales@amcomfg.com TOUGH 1947 TILLAGE TOOLS SINCE Shock Absorber Bearing Riser with AMCO's Protect-O-Shield Bearings Protect-O-Shield Bearings PROTECT-OSHIELD BEARING INNER RACE DUCTILE HOUSING FOR TOGGLE MOUNTING Shock Absorber Bearing Riser GREASE FITTING PROTECT-OSHIELD TRIPLE-LIP SEALS GREASE GROOVE AMCO's Protect-O-Shield Bearing features an exclusive protective shield and is guaranteed for two full years. Our bearing eliminates blown seals and prevents wrap damage. Our Shock Absorber Bearing Riser allows the gang on the harrow to move upward and back to relieve shock when the disc blades encounter an obstacle in the ground. 12/30/2014 DOUBLE OFFSET TANDEM DISC HARROW STANDARD FEATURES
AMCO's Shock Absorber Gang Riser (Side View) Model # 30-50 50-100 100-150 150-200 200-250 250-300 300-350 350-400 400+ Ditcher 540 Ditcher 1000 LOF D41 F41 J41 F42 J42 J43 J44 G2 LTF 100 Wicked Warrior F15B F15 F17 TJ3 LF6 & LJ6 MLF6 & MLJ6 Ripper Bedding Hipper
Protect-O-Shield Bearings Guaranteed for two full years. PROTECT-OSHIELD GREASE FITTING PROTECT-OSHIELD BEARING INNER RACE DUCTILE HOUSING FOR TOGGLE MOUNTING TRIPLE-LIP SEALS GREASE GROOVE F17 DOUBLE OFFSET TANDEM DISC HARROW For dependable seedbed preparation, you can rely on AMCO s F17 Double Offset Tandem Disc Harrow. Built AMCO tough, the F17 opens and breaks up the surface, smoothing the soil so your ideal seedbed is ready for planting. Since each farming operation is different, AMCO s Double Offset Tandem Disc Harrow is available in a wide variety of sizes. Weighing between 296 and 337 pounds per cutting foot, the disc harrows are available in 9'3", 10'6", 12'0", 13'6", 15'0", and 16'6" models for use with tractors ranging from 67 to 175 engine horsepower. FEATURES High-quality features are essential in today s farming operation, and the F17 won t disappoint. Features include: Eight or twelve (depending on model size) greasable ball-type, toggle-mounted Protect-O-Shield bearings, guaranteed for two full years. 1½" square, high-carbon, cold-rolled steel axles Reversible clevis Heavy-duty scrapers with high-carbon replaceable blades Standard 22" x ¼" plain blades on 9" spacing Diminishing blades with 16" feathering blades on the rear gang Standard gang bolt wrench and a 4" x 8" (3,000 PSI) hydraulic cylinder with hoses to tractor Wear guards to protect bearing housing and zerk guards to protect grease fitting Dealing with unexpected or unpredictable terrain? Try the optional Shock Absorber Gang Riser, which allows the gang on the harrow to move upward and back to relieve shock when the disc blades encounter an obstacle in the ground. Other customization options include 15 x 10 wheels in place of 15 x 8 wheels, dual wheels in place of single wheels, cutout blades in place of the standard plain blades, and scrapers for the rear feathering blades. More blade configurations are available as well call to discuss your options.
Left: Diminishing blades on the rear gang and feathering blades provide a smooth, even cut. Below: For unexpected or unpredictable terrain, try the optional Shock Absorber Gang Riser. The gang will move upward and back to relieve shock when the blades strike an obstacle. Left: Heavyduty scrapers feature high-carbon replaceable steel blades. F17 Double Offset Tandem Disc Harrow models Model Cutting Number Number of Width of Discs Bearings Approx. Engine HP Required Approx. Weight F17-2622 9'3" 26 8 65 101 3,360 lbs F17-3022 10'6" F17-3422 12'0" 30 8 81 108 3,644 lbs 34 8 95 122 3,928 lbs F17-3822* 13'6" 38 12 108 135 4,708 lbs F17-4222* 15'0" 42 12 122 155 5,022 lbs F17-4622* 16'6" 46 12 142 175 5,536 lbs 800 S. Industrial Parkway P. O. Box 1107 Yazoo City, MS 39194 Toll free: 800-748-9022 662-746-4464 Fax: 662-746-5466 Web: www.amcomfg.com Facebook: www.facebook.com/ AMCOManufacturingInc Email: sales@amcomfg.com TOUGH 1947 TILLAGE TOOLS SINCE *Includes 2 outrigger bars and clamps. Specifications subject to change without notice. 6/6/2014 Above: Front to rear leveling spring allows easy adjustment in the field. The standard tongue jack and gang bolt wrench both fit in place on the tongue during operation. A 4" x 8" (3,000 PSI) hydraulic cylinder with hoses to tractor is also standard equipment. Above: An easy-to-install transport lockout holds the disc in the raised position when folded for transport.
Prices and Specifications may be subject to change without notice. Prices do not include shipping or setup. Prices Effective as of 10-17 LIFT TRUE TANDEM MODEL "Wicked Warrior" 7.5" Spacing Economy Disc STANDARD SPECIFICATIONS
Prices Effective as of 10-17 LIFT TANDEM DOUBLE OFFSET MODEL "LTF 100" 9" Spacing Primary Tillage STANDARD SPECIFICATIONS Prices and Specifications may be subject to change without notice. Prices do not include shipping or setup.
Prices Effective as of 10-17 DOUBLE OFFSET TANDEM MODEL "F15B" 9" Spacing 16'6", 18'0", 19'6", 21'0", 24'0" Sizes STANDARD SPECIFICATIONS Prices and Specifications may be subject to change without notice. Prices do not include shipping or setup.
Prices Effective as of 10-17 DOUBLE OFFSET TANDEM MODEL "F15" 9" spacing 24'0", 27'0", 30'0" Sizes STANDARD SPECIFICATIONS Prices and Specifications may be subject to change without notice. Prices do not include shipping or setup.
Prices Effective as of 10-17 DOUBLE OFFSET TANDEM MODEL "F15" 9" Spacing 34'6" AND 39'0" Sizes STANDARD SPECIFICATIONS Prices and Specifications may be subject to change without notice. Prices do not include shipping or setup.
Prices Effective as of 10-17 DOUBLE OFFSET TANDEM MODEL "F17" 9" spacing STANDARD SPECIFICATIONS to 22 Front Prices and Specifications may be subject to change without notice. Prices do not include shipping or setup.