BANKABLE VALVES Technical Catalogue January 2018

Similar documents
BANKABLE VALVES Technical Catalogue August 2017

BANKABLE VALVES (PROPORTIONAL and ON/OFF versions) Technical Catalogue

CX3 SOLENOID OPERATING PROPORTIONAL CONTROL BANKABLE VALVES FEATURES ORDERING CODE HYDRAULIC SYMBOLS

CXDH3 / CDH3 - Features

CARTRIDGE VALVES / IN-LINE VALVES

HPV310 PROPORTIONAL DIRECTIONAL VALVES

4/2 Directional valve elements with or without secondary relief valves, with or without LS connections, and with 2/2 solenoid cartridge valve

Introduction. Pressure drops

MDT. Monoblock directional control valves MDT - Directional control valve

DIRECTIONAL CONTROL VALVES CETOP 3/NG6

4/3-4/2 Directional valve elements with or without secondary relief valves, and with or without LS connections

4/3 and 4/2 on-off directional valve elements D8_5 with or (EDD-XZ) without secondary relief valves and with or without LS connections D8_5 (EDD-XZ)

p max (see table of performances) Q max (see table of performances) MD1K MD1KD bar

HPV310 PROPORTIONAL DIRECTIONAL VALVES. Technical Catalogue

DFE10. solenoid control monoblock valve. Ordering codes. Description example : Diverter valve DFE10/3 A 18 ES - W VDC - SAE - <CVN>

Monobloc and Sectional Directional Control Valves

Monobloc and Sectional Directional Control Valves

Proportional Directional Valve System

Monobloc and Sectional Directional Control Valves

Monobloc and Sectional Directional Control Valves

B8_58 (EDBZ-VEI) RE Edition: Replaces:

TECHNICAL CATALOGUE ARON 2005

4/3-4/2 Directional valve elements with or without secondary relief valves, and with or without LS connections

Solenoid directional valves type DPHI, DPHE, DPHER two stage, ISO 4401 size 10, 16, 25 and 32

TESTO ITC KORINNA 28mm Allargato LOAD SENSING MONOBLOCK DIRECTIONAL CONTROL VALVE

DIRECT CURRENT MOTORS

Proportional pressure reducing valve of 3-way design

4/3-4/2 Directional valve elements B8_0A with or without (EDB-A) secondary relief valves, with or without LS connections B8_0A (EDB-A)

Monoblock Directional Control Valve HDM11S/3PQ

DIRECTIONAL CONTROL VALVES CETOP 5/NG10

VALVES POWER TRANSMISSION T E C H N I C A L C A T A L O G

Proportional Flow-Control Cartridges, Size 5

4/3-way high response directional control valve pilot operated with electrical feedback and integrated electronics (OBE)

ISO cartridge valves type LIDD and LIQV Flow control, ISO 7368 sizes 16 63

Monoblock directional control valves DL - Directional control valve

油力油壓工業股份有限公司 YOULI HYDRAULIC INDUSTRIAL CO.,LTD. ISO 9001:2008 QA100189

ADB.3... DIRECTIONAL CONTROL

HPV310 PROPORTIONAL DIRECTIONAL VALVES. Technical Catalogue

RPEK1-03/B. Functional Description HA /2011. RPEK1-03 Modular Valve Assembly. D n 03 p max 250 bar (3626 PSI) Q max 60 l/min (15.

DFE. solenoid control monoblock valve. Content. Working conditions Hydraulic circuit DFE052. Dimensional data Ordering codes...

IFP DG08 SOLENOID CONTROLLED PILOT OPERATED DIRECTIONAL VALVE SIZE NG22/CETOP08

Directional Control Valves Series D81V. General Description. Operation. Features. Specifications

Flow sharing control block in mono block / sandwich plate design M6-22

4/3 4/2 Directional valve elements with or without secondary relief valves, and with or without LS connections

Flow sharing control block in mono block / sandwich plate design M6-15

2/2 CARTRIDGE VALVES LOGIC ELEMENTS

6-way Changeover valves 6VA VG VM VR VS way Changeover valves 8VR... 20

Directional Control Valves. Features. Application. Operation

Pump Safety Block Model DBA... / DBAW, Series 1X

Directional Control Valves. General Description. Operation. Features

SD2E-A4. Functional Description. 4/2 Way Solenoid Operated Directional Control Valves Spool Type HA /2014. Replaces HA /2013

Proportional flow control valve with integrated pressure compensator Type KUDSR

LUDV control block of sandwich plate design

3/2 and 4/2 directional seat valves with solenoid actuation

250 bar P max. Technical Features. Functional Description

Rexroth Hydraulics. Servo directional valve of 4-way design Type 4WS.2EM RE /03.99

VALVES AND ELECTRONICS

4-way directional servo-valve

COMPACT CATALOGUE SECTIONAL DIRECTIONAL CONTROL VALVES

IFP DG07 SOLENOID CONTROLLED PILOT OPERATED DIRECTIONAL VALVE SIZE NG-16 / CETOP-07

Functional Description

BW0511FP. ByWire Elements BW0511FP Flow Sharing Element Interface IBW0511

Umschaltventile Magnet

Monobloc and Sectional Directional Control Valves

COMPACT CATALOG MONOBLOCK DIRECTIONAL CONTROL VALVES

4/3-4/2 Directional valve elements LF1_1 (LC1F-Z)

Variable Displacement Plug-In Motor A6VE

Stand alone 4/3, 4/2 solenoid operated directional valve

DXPE*J /117 ED. DIRECtIONAL CONtROL VALVE PILOt OPERAtED, WItH OBE AND FEEDBACK. Q max (see performance table) SERIES 31

45 lpm. Part Number Spool Qty Max Flow Max Pressure Ports. 45 lpm. Relief Valve Standard Bar Range Power Beyong Plug included in every kit

Stand alone 4/3, 4/2 direct acting directional valve LF2_1 (LC2F-DZ)

SD3E-B2. Functional Description. 2/2 Way Solenoid Operated Directional Control Valves Poppet Type HA /2012. Replaces HA /2010

Proportional pressure reducing valve of 3-way design Types 3DREP and 3DREPE

Pressure relief valve, pilot-operated. Type DB and DBW. Features. Contents. RE Edition: Replaces:

Safety cartridge valves with poppet position monitoring

Differential Lock Valve

BS3... SINGLE STATION SUBPLATE

Differential Lock Valve

MB-4 Chapters Monoblock Directional Control Valves

YOULI HYDRAULIC INDUSTRIAL CO.,LTD.

CONTROL VALVES

PRM7-04. Functional Description HA /2012. Proportional Directional Control Valves. Replaces HA /2009

Accumulator shut-off block. Type 0532VAW. Contents. Features. RE Edition: Replaces: 07.10

Part Number Spool Qty Max Flow Max Pressure Ports. 80 lpm

Differential Lock Valve

Pilot operated pressure relief valve

YOULI HYDRAULIC INDUSTRIAL CO.,LTD.

COMPACT CATALOGUE SECTIONAL DIRECTIONAL CONTROL VALVES

Directional control valves NG6...NG32 D03...D10 6

Directional control valves, pilot-operated, with electrical position feedback and integrated electronics (OBE) Type 4WRDE. Contents.

TPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 852 / 0815 / E

Proportional pressure reducing valve, in 3-way version

Differential Lock Valve

PRM7-06. Functional Description HA /2006. Proportional Directional Control Valves. Replaces HA /2002

PRM7-06. Functional Description HA /2014. Proportional Directional Control Valves. Replaces HA /2013

3-Way heavy duty flow control, with pressure compensated, solenoid and load sensing controlled priority flow

Direct Operated Proportional DC Valves

USA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI U.S.A. Tel: FAX:

3/2 and 4/2 directional poppet valve with solenoid actuation

Directional Control Valve

Transcription:

NKLE VLVES echnical Catalogue January 08 web edition

ankable valves able of contents ECHNICL INFORMION... SIZE 6...5 ON/OFF ND ROORIONL VLVES (CDC / CD / CX / CXQ)...6 Composition form...8 Inlet module units...0 Working sections...5 Intermediate element...47 Outlet module units...5 RE ND OS COMENSED VLVES (CXDH / CDH / CFS)...56 Composition form...58 Inlet module units...59 Working sections...65 Intermediate element...78 Outlet module units...79 SIZE 0...8 ON/OFF VLVES (CD5)...8 Composition form...8 Inlet module units...84 Working sections...87 Outlet module units...90 MODULR ELEMENS...9 Valves and modular elements...9 CCESSORIES...99 Interface for proportional directional valves HV4...00 Mounting kit...0 Fixing feet...0 Calibrated diaphragms...04 Connectors...05 Coils....06 HOW O ORDER... Examples....4 ELECROMGNEIC COMIILIY...7 i 4 5 6 08 Dana revini S.p.. all rights reserved. Hydr-pp, SM Hydraulik, ron, revini Hydraulics, E Electronics, VS revini, O Oiltechnology, logos are trademarks or are registered trademarks of Dana revini S.p.. or other companies Dana in Italy and other countries. he technical features supplied in this catalogue are non binding and no legal action can be taken against such material. Dana revini will not be held responsible for information and specifications which may lead to error or incorrect interpretations. Given the continuous technical research aimed at improved technical features of our products, Dana revini reserves the right to make change that are considered appropriate without any prior notice. his catalogue cannot be reproduced (in while or in part) without the prior written consent of Dana revini. his catalogue supersedes all previous ones. Use of the products in this catalogue must comply with the operating limits given in the technical specifications. he type of application and operating conditions must be assessed as normal or in malfunction in order to avoid endangering the safety of people and/or items. IE/NK-INDEX/0-05 0

ECHNICL INFORMION INRODUCION CONVERSION LE SSU / E / mm²/s i Read this instructions carefully before installation. ll operations must be carried out by qualified personnel following the instructions. he user must periodically inspect, based on the conditions of use and the substances used, the presence of corrosion, dirt, the state of wear and correct function of the valves. lways observe first the operating conditions given in datasheet of the valve. HYDRULIC FLUID Observe the recommendations given in the data sheet of the valve. Use only mineral oil (HL, HL) according to DIN 554. Use of other different fluids may damage the good operation of the valve. 5000 5000 500 500 00 50 50 600 5000 0000 500 400 4000 0000 00 000 000 00 500 50 000 00 000 500 000 40 50 400 0 00 00 400 0 00 0 50 00 40 5 0 00 4 0 0 0 0 SSU E mm²/s VISCOSIY OIL VISCOSIY CCORDING O EMERURE Observe the recommendations given in the data sheet of the valve.he oil viscosity must be in the range of 0 mm²/s to 500 mm²/s. Recommended oil viscosity 46 mm /s ( mm /s for Cartridge valves) able : ISO viscosity grades verage kinematic viscosity mm²/s @ 40 C Viscosity grade Kinematic-viscosity limits mm²/s @ 40 C min. max. ISO VG 0 0 9.00.0 ISO VG 5 5.5 6.5 ISO VG 9.8 4. ISO VG 8.8 5. ISO VG 46 46 4.4 50.6 ISO VG 68 68 6. 74.8 ISO VG 00 00 90.0 0 = Values used in the chart Oil viscosity according to temperature E 9 8 7 6 mm²/s 000 0000 000 7000 5000 500 000 00 00 00 70 40 0 0 8 6 4.8.6 000 500 000 800 600 400 00 00 50 00 70 60 50 40 0 5 0 7 5 0 ISO VG 00 ISO VG 68 ISO VG 46 ISO VG ISO VG.4. 5 4.5 4.5..80-0 0-5 -0-5 0 5 0 5 0 5 0 40 50 60 70 80 90 00 70 00 0 40 00 0 0 C F IE/NK-INRO/0-05

ECHNICL INFORMION CONMINION Oil contamination is the main cause of faults and malfunction in hydraulic systems. brasive particles in the fluid erode or block moving parts, leading to system malfunction. he valves we are offering do not require filtering characteristics any higher than those needed for usual hydraulic components such as pumps, motors, etc. However, accurate filtering does guarantee reliability and a long life to all the system s hydraulic parts. Reliable performance and long working life for all oil-pressure parts is assured by maintaining the level of fluid contamination within the limits specified in the data sheet of the valve. Hydraulic fluid must also be cleaned properly before filling the hydraulic circuit, especially when commissioning a new system, as this is when the oil contamination generally peaks due to its flushing effect on the components, and the running-in of the pump. Maximum contamination level is required on datasheet of the valve according to ISO 4406:999. In the following table there is the correspondence between ISO 4406:999 and old standard NS 68 for information purpose: he standard ISO 4406:999 defines the contamination level with three numbers that relate with the number of particles of average dimension equal or greater than 4 μm, 6 μm e 4 μm, in ml of fliuid. In following table there is a reference to reccomended contamination level and correspondence with old NS 68 standard. able : Reccomanded contamination level. Oil filtration recommendations ype of system Cleanliness class recommended ype of valve NS 68 ISO 4406 : 999 ( ) Systems or components operating at HIGH RESSURE > 50 bar (600 psi) HIGH DUY CYCLE LICIONS Systems or components with LOW dirt tolerance Systems or components operating at MEDIUM / HIGH RESSURE Systems and components with moderate dirt tolerance Systems or components operating at LOW RESSURE < 00 bar (500 psi) LOW DUY CYCLE LICIONS Systems and components with GOOD dirt tolerance bsolute filtration micron rating ( ) 8 / 6 / 7-8 5 9 / 7 / 4 9 0 0 / 8 / 5 0-0 Contamination class NS 68: it is determined by counting the total particles of different size ranges contained in 00 ml of fluid. bsolute filtration: it is a characteristic of each filter, it refers the size (in micron) of the largest sperical particle wich may pass through the filter. SELS O-rings made in crylonitrile utadiene (NR) are normally fitted on the valves. he backup rings that protect the O-rings are also made in NR, or sometimes FE. oth the O-rings and the backup rings are suitable for the working temperatures mentioned above. In the case of fluid temperatures > 75 C, FKM seals must be used (identified with V variant). ELECRICL OWER SULY Solenoid valves coils are designed to operate safely in the voltage range of ±0% of nominal voltage at max. 60 C ambient temperature. he combination of permanent overvoltage and very hot temperatures can stress the solenoid. herefore always a good heat dissipation and voltage level has to be assured. Faulty coils may only be replaced by new, interchangeable, tested components in original-equipment quality. efore removing a coil, voltage must be disconnected. When replacing the coil, be aware to insert O-Rings in order to avoid the entrance of water. INSLLION he mounting surface must feature surface quality specified in data sheet of the valve: for example for Cetop valves generally is required Ra.6μm and flatness 0.0 mm over 00 mm length. Normally in cartridge valve for sealing diameters of the cavities, is required roughness Ra.6μm. he surfaces and openings in the assembly plate must be free from impurity or dirt. Make sure the O-Rings fit correctly in their seats. Fixing screws must comply with the dimensions and the strength class specified in the data sheet and must be tightened at the specified tightening torque. Complete the electrical wiring. For circuit examples and pin assignments, see the relevant datasheet. USE ND MINENNCE Observe the functional limits indicated in the technical catalogue On a periodic basis and based on the conditions of use, check for cleanliness, state of wear or fractures and correct performance of the valve. If the O-rings are damaged, replace them with those supplied by the manufacturer. o assure the best working conditions at all time, check the oil and replace it periodically (after the first 00 working hours and then after every 000 working hours or at least once every year). ttention: all installation and maintenance intervention must be performed by qualified staff. i WORKING EMERURES mbient temperature range: -5 C to +60 C Fluid temperature range (NR seals): -5 C to +75 C hermal shocks can affect the performance and the expected life of the product, hence it is necessary to protect the product from these conditions. RNSOR ND SORGE he valve must be handled with care to avoid damage caused by impact, which could compromise its efficiency. In the case of storage, keep the valves in a dry place and protect against dust and corrosive substances. When storing for periods of more than 6 months, fill the valve with preserving oils and seal it. IE/NK-INRO/0-05

ECHNICL INFORMION CONVERSION CHR ype SI units lternative units Conversion factor i Force Newton (N) [kgm/s²] Kilogram force (kgf) kgf = 9.807 N pound force (lbf) [lbf/s²] lgf = 4.448 N millimeter (mm) [0 m] inch (in) in = 5.4 mm Length meter (km) [000 m] yard (yd) [ft] m =.096 yd kilometer (km) [000 m] mile (mile) [760 yd] mile =.609 km orque Newton meter (Nm) pound force.feet (lbf.ft) lbf.ft =.56 Nm ower kilowatt (kw) [000 Nm/s] horsepower (hp) kw =.4 hp metric horsepower (CV) kw =.6 CV bar Ma = 0 bar ressure Megaascal (Ma) [ N/mm²] psi (lbf/ln²) Ma = 45 psi ton/f/ln² ton/f/ln² = 5.45 Ma Flow rate liter/min (l/min) UK gal/min UK gal/min = 4.546 l/min US gal/min US gal/min =.785 l/min emperature Degrees Celsius ( C) Farenheit ( F) F =.8 C+ IE/NK-INRO/0-05 4

SIZE 6 ON/OFF VLVES ROORIONL VLVES RE ND OS COMENSED VLVES 5

69 46 Ch./Hex. 0 ON/OFF ND ROORIONL VLVES Introduction ankable ON/OFF directional control valves; ankable ROORIONL directional control valves; ankable ROORIONL COMENSED flow regulators; ON/OFF valves available in two sizes, with reduced overall dimensions or for high flow rates; vailable for parallel or series circuits; vailable with housing with threaded ports or interfaces for modular valves; vailable for Load Sensing circuits; ssemblable with FEH0 and FUH family inlet and outlet modules; ssemblable with CXDH, CDH, CD5 family valves; ssemblable with Dana revini HV valves (intermediate element required). Overall dimensions with CDC valves 7 FE0 009 009 FU 0 D C No. elements C mm FE / FE0 Inlet module D mm C mm FE D mm 9 80 0 90 8 6 48 6 4 84 7 94 8 5 0 8 40 6 6 76 64 86 74 7 4 40 4 40 8 468 456 478 466 IE/NK-ONOFF/0-05 6

69 46 Ch./Hex. 0 ON/OFF ND ROORIONL VLVES Overall dimensions with CD valves FE0 FU 7 009 009 0 D C No. elements C mm FE / FE0 Inlet module D mm C mm FE D mm 9 80 0 90 8 6 48 6 4 84 7 94 8 5 0 8 40 6 6 76 64 86 74 7 4 40 4 40 8 468 456 478 466 IE/NK-ONOFF/0-05 7

Composition form 8 7 6 5 7 6 5 0 8 4 9 4 0 0 7 8 9 5 4 9 6 0 SIZE 6 valves CDC, CD, CX can be assembled with: - valves CXDH, CDH, CFS (page 56); - with SIZE 0 valves CD5 (page 8); - with proportional directional valves HV4 (see catalogue code DOC00079) using the interface HSIF (page 00). o obtain the best performances, we suggest to assemble the working sections with higher flow rate near the inlet module, leaving the ones with lower flow at the end of the assembled valve. How to order o order the assembly, specify the codes in progressive order (inlet, valves, outlet, mounting kit, feet). See example page 4. For any further special version not shown in this catalogue, please contact our echnical Department. IE/NK-ONOFF/0-05 8

Composition form Ref. ype Description age FE FELS Inlet module units no pressure relief valve 0 Inlet module units with LS line no pressure relief valve FE0 Inlet module units with pressure relief valve (up to 0 l/min) FE0Q Inlet module units with LS line, compensator and pressure relief valve 4 FE0 FE0LS Inlet module units with pressure relief valve 5 Inlet module units with LS line with pressure relief valve 6 5 FE0S Inlet module units with side ports and pressure relief valve 7 6 FE0X Inlet module units with pressure relief valve for proportional pressure compensated flow regulator XQ 9 7 XQ ressure compensated flow regulator see catalogue Valves and Electronics code. DOC00078 8 FE0 Inlet module units with pressure relief valve and electrical venting valve 9 FE0S Inlet module units with side ports, pressure relief valve and electrical venting valve 0 CDC Directional control bankable valve with 09 coils 5 CDC / CDCM (variants) 4 CDM Directional control bankable valve with pressure relief valve and 09 coils 0 CDC / CDCM (variants) 4 CD Directional control bankable valve with D5 coils 5 CD (variants) 40 CX Solenoid operating proportional control bankable valves 4 4 CXQ Open loop proportional pressure compensated bankable flow regulators 44 5 FI Intermediate element 47 6 FIL Intermediate element with LS line 48 7 FIR Intermediate element with pressure reducing valve 49 8 CDCR Directional control valve connection - for Intermediate element FI 50 9 FI Intermediate element for valve CDCR 5 0 CD CDC CX ody G-H-M for modular valves 5-5 - 4 FU Outlet module units 5 FU Outlet module units with side ports 54 FUS Outlet module units with overcenter and top port 55 4 V08000005 Intermediate element with flow regulator on and lines 9 5 V0800000 Intermediate element with pilot operated check stackable valves 9 6 CMF Modular elements with ports - 94 7 CM Modular pilot operated check bankable valves 95 8 CMM Modular max. pressure bankable valves 97 9 HSIF Interface for proportional directional valves HV4 00 0 Mounting kit 0 Fixing feet 0 Connectors 05 Coils 06 IE/NK-ONOFF/0-05 9

FE INLE MODULE UNIS NO RESSURE RELIEF VLVE Module units FE no pressure relief valve. hreaded ports ( and ), G/8 or 9/6-8UNF Maximum fl ow 40 l/min. luminum body. FEURES HYDRULIC SYMOL Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm²/s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0. kg ORDERING CODE OVERLL DIMENSIONS FE Inlet module unit no pressure relief valve Size 5 70 ort sizes: = G/8" = 9/6-8UNF 00 = No variant V = Viton Serial No. 60 0 4 49 59 9 4 n. 4 fori x OR -0 90Sh 6.5 IE/FE00/0/0 0

FELS INLE MODULE UNIS WIH LS LINE NO RESSURE RELIEF VLVE Module units FELS with LS line, no pressure relief valve. hreaded ports ( and ) sizes G/8 and LS size G/4. Maximum fl ow 40 l/min. luminum body. FEURES HYDRULIC SYMOL LS Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm²/s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0. kg ORDERING CODE OVERLL DIMENSIONS FELS Inlet module unit no pressure relief valve with LS line 5 70 Size orts: = G/8 (, ports) G/4 (LS port) 00 = No variant V = Viton Serial No. 70 4 49 59 4 N 4 Ø 6.5 40 8 LS 5 FELS G /4" OR 07/-0 90Sh.5 9 4 OR 08/-008 90Sh IE/FELS00/0/0

FE0 INLE MODULE UNIS WIH RESSURE RELIEF VLVE (U O 0 L/MIN) Module units FE0 with CM-MC/MS adjustable pressure relief valve Manual adjustment with a grub screw. Fhreaded ports ( and ) sizes G/8 or 9/6-8UNF. Maximum fl ow 0 l/min. luminum body. FEURES HYDRULIC SYMOL Max. operating pressure 50 bar Max. Flow 0 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.4 kg ressure relief valve (CM-MC/MS Setting range (): Spring Spring Spring Spring 4 max 50 bar max 90 bar max 90 bar max 90 bar () he minimum permissible setting pressure depending on the spring: see curves. ORDERING CODE RESSURE-FLOW RE MIN.SEING RESSURE FE0 C Inlet module unit (up to 0 l/min) with pressure relief valve Size ort sizes: = G/8" = 9/6-8UNF djustment: C = Grub screw Setting ranges = 0 50 bar (white spring) = 5 90 bar (green spring) = 75 90 bar (yellow spring) 4 = 60 90 bar (red spring) 00 = No variant V = Viton Serial No. (bar) 50 60 4 Q (l/min) = 0 50 bar - = 5 90 bar - = 75 90 bar - 4 = 60 90 bar Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C..5 70 7.5 4 0 00 50 00 50 00 50 0 0 4 6 8 0 4 6 8 0 OVERLL DIMENSIONS 8.5 (bar) 55 4 50 45 40 5 0 5 0 5 0 5 0 0 4 6 8 0 4 6 8 0 Q (l/min) CH 4 49. max CH 0 CH () Setting referred to the maximum pressure reached from the relief valve. Do not exceed the maximum working pressure 50 bar. 4 49 n. 4 fori 59 x OR -0 90Sh 6.5 IE/FE000/0-05

FE0Q INLE MODULE UNIS WIH LS LINE, COMENSOR ND RESSURE RELIEF VLVE Module units FE0Q with pressure compensator for fi xed displacement pumps and CM-MC/MS adjustable pressure relief valve on LS line Manual adjustment with a grub screw. Screw with orifi ce for LS bleeding. hreaded ports -, G/8 and LS, G/4. Maximum fl ow 40 l/min. luminum body. FEURES HYDRULIC SYMOL GRY GRX Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight kg Ø0.6 Ls Grano cieco lug ressure relief valve (CM-MC/MS Setting range (): Spring Spring Spring Spring 4 max 50 bar max 90 bar max 90 bar max 90 bar () he minimum permissible setting pressure depending on the spring: see curves. ORDERING CODE RESSURE COMENSOR FE0Q C Inlet module unit (up to 40 l/min) with compensator and pressure relief valve Size orts: = G/8 (, ports) - G/4 (LS port) = 9/6-8UNF (, ports) - 7/6-0UNF (LS port) djustment: C = Grub screw Setting ranges = 0 50 bar (white spring) = 5 90 bar (green spring) = 75 90 bar (yellow spring) 4 = 60 90 bar (red spring) 00 = No variant V = Viton Serial No. (bar) 6 4 0 8 6 4 0 0 4 6 8 0 4 6 8 0 Q (l/min) Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. o obtain a correct compensation the inlet fl ow must be 8% greater the sum of the regulated fl ow. () Setting referred to the maximum pressure reached from the relief valve. Do not exceed the maximum working pressure 50 bar. IE/FE0Q00/0-06

FE0Q OVERLL DIMENSIONS 59 6 G /8" 6 48 5 66 49 G /8" 8 57 5,80 85 70 49 OR 07/-0 90Sh OR 08/-008 90Sh 59 N 4 Ø 6.5 IE/FE0Q00/0-05 4

FE0 INLE MODULE UNIS WIH RESSURE RELIEF VLVE Module units FE0 with CM0 adjustable pressure relief valve. Manual adjustment with a grub screw or plastic knob. hreaded ports - sizes G/8 or 9/6-8UNF. Maximum fl ow 40 l/min. luminum body. HYDRULIC SYMOL FEURES Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.6 kg ressure relief valve (CM0...) Setting range (): Spring max 50 bar Spring max 50 bar Spring max 0 bar () he minimum permissible setting pressure depending on the spring: see curves. ORDERING CODE RESSURE-FLOW RE MIN.SEING RESSURE FE0 Inlet module unit (up to 40 l/min) with pressure relief valve Size ort sizes: = G/8 = 9/6-8UNF djustment: M = lastic knob C = Grub screw Setting ranges = max. 50 bar (white spring) = max. 50 bar (yellow spring) = max. 0 bar (green spring) 00 = No variant V = Viton (bar) 60 0 80 40 00 60 0 80 40 0 0 5 0 5 0 5 0 5 40 Q (l/min) 0 0 5 0 5 0 5 0 5 40 Q (l/min) = max 50 - bar - = max 50 bar - = max 0 bar Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. OVERLL DIMENSIONS 6.5 70.5 (bar) 00 80 60 40 0 54 max Serial No. () Setting referred to the maximum pressure reached from the relief valve. Do not exceed the maximum working pressure 50 bar. 60 4 9 4 C = Grub screw M = lastic knob C CH 5 49 59 n. 4 fori Ø 6.5 x OR -0 90Sh 5.5 max 40 M IE/FE000/0/0 5

FE0LS INLE MODULE UNIS WIH LS LINE WIH RESSURE RELIEF VLVE Module units FE0LS with LS line and CM0 adjustable pressure relief valve. Manual adjustment with a grub screw or plastic knob. hreaded ports -, G/8 and LS, G/4. Maximum fl ow 40 l/min. luminum body. FEURES HYDRULIC SYMOL ORDERING CODE FE0LS LS FE0LS.. Inlet module unit (up to 40 l/min) with pressure relief valve and LS line LS FE0LS..J6. Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.6 kg ressure relief valve (CM0...) Setting range (): Spring Spring Spring max 50 bar max 50 bar max 0 bar () he minimum permissible setting pressure depending on the spring: see curves. Size orts: = G/8 (, ports) G/4 (LS port) djustment: M = lastic knob C = Grub screw OVERLL DIMENSIONS 70 6.5.5 54 max Setting ranges = max. 50 bar (white spring) = max. 50 bar (yellow spring) = max. 0 bar (green spring) 70 4 9 4 C 00 = No variant J6 = With LS bleed V = Viton 0.5 5.5 49 59 N 4 Ø 6.5 Serial No. () Setting referred to the maximum pressure reached from the relief valve. Do not exceed the maximum working pressure 50 bar. 40 8 LS FE0LS M RESSURE-FLOW RE MIN.SEING RESSURE 0 6.5 max 60 0 80 00 80 4 5 x OR 07/-0 90Sh (bar) 40 00 60 0 80 40 (bar) 60 40 0 9.5 OR 08/-008 90Sh 0 0 5 0 5 0 5 0 5 40 Q (l/min) 0 0 5 0 5 0 5 0 5 40 Q (l/min) = max 50 bar - = max 50 bar - = max 0 bar Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. C = Grub screw M = lastic knob IE/FE0LS00/0-05 6

FE0S INLE MODULE UNIS WIH SIDE ORS ND RESSURE RELIEF VLVE Inlet module units FE0S with side ports and CM0 adjustable pressure relief valve. Manual adjustment with a grub screw or plastic knob. hreaded ports -, G/8 or G/8 () - G/ (). Maximum fl ow 40 l/min. luminum body. FEURES HYDRULIC SYMOL M Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.6 kg ressure relief valve (CM0...) Setting range (): Spring Spring Spring max 50 bar max 50 bar max 0 bar () he minimum permissible setting pressure depending on the spring: see curves. ORDERING CODE RESSURE-FLOW RE MIN.SEING RESSURE FE0S Inlet module unit with side ports and pressure relief valve (up to 40 l/min) Size orts: = G/8 ports, 5 = G/8 port - G/ port djustment: M = lastic knob C = Grub screw Setting ranges = max. 50 bar (white spring) = max. 50 bar (yellow spring) = max. 0 bar (green spring) (bar) 60 0 80 40 00 60 0 80 40 0 0 5 0 5 0 5 0 5 40 Q (l/min) 0 0 5 0 5 0 5 0 5 40 Q (l/min) = max 50 bar - = max 50 bar - = max 0 bar Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. (bar) 00 80 60 40 0 00 = No variant V = Viton Serial No. () Setting referred to the maximum pressure reached from the relief valve. Do not exceed the maximum working pressure 50 bar. IE/FE0S00/0-05 7

FE0S OVERLL DIMENSIONS C 54 max x O-RING -0 90Sh 6.5 max M G /8" 90 4 5 49 59 80 G /4" C = Grub screw M = lastic knob IE/FE0S00/0-05 8

FE0X INLE MODULE UNIS WIH RESSURE RELIEF VLVE FOR ROORIONL RESSURE COMENSED FLOW REGULOR XQ Module units FE0X for proportional pressure compensated fl ow regulator XQ. With CM0 adjustable pressure relief valve. Manual adjustment with a grub screw or plastic knob. hreaded ports - sizes G/8. Maximum fl ow 40 l/min. luminum body. FEURES HYDRULIC SYMOL XQ FE0X Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class 9/7/4 NS 68: class 8 Weight 0.6 kg ressure relief valve (CM0...) Setting range (): Spring Spring Spring max 50 bar max 50 bar max 0 bar () he minimum permissible setting pressure depending on the spring: see curves. ORDERING CODE RESSURE-FLOW RE MIN.SEING RESSURE FE0X Inlet module unit (up to 40 l/min)for proportional pressure compensated fl ow regulator Size orts: = G/8 ports, djustment: M = lastic knob C = Grub screw Setting ranges = max. 50 bar (white spring) = max. 50 bar (yellow spring) = max. 0 bar (green spring) 00 = No variant V = Viton Serial No. (bar) 60 0 80 40 00 60 0 80 40 0 0 5 0 5 0 5 0 5 40 Q (l/min) 0 0 5 0 5 0 5 0 5 40 Q (l/min) = max 50 bar - = max 50 bar - = max 0 bar Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. (bar) 00 80 60 40 0 () Setting referred to the maximum pressure reached from the relief valve. Do not exceed the maximum working pressure 50 bar. IE/FE0X00/0-05 9

FE0X OVERLL DIMENSIONS 59 4 C 59 8.5.5 XQ o order, see catalogue Valves and Electronics code. 50000 x O-RING -0 90Sh 4 49 58 max 4 9 9 58 70 M 6.5 max ISO 440 CEO/NG6,5,5 9 C = Grub screw M = lastic knob N 4 M5 40,5 IE/FE0X00/0-05 0

FE0 INLE MODULE UNIS WIH RESSURE RELIEF VLVE ND ELECRICL VENING VLVE Module units FE0 with CM0 adjustable pressure relief valve and electrical venting valve CR048N normally open supplied with emergency control. Manual adjustment with a grub screw or plastic knob. hreaded ports - sizes G/8 or 9/6-8UNF. ressure gauge M, G/4 Maximum fl ow 40 l/min. luminum body. Connector to be ordered separately, see page 05. HYDRULIC SYMOL ORDERING CODE FE0 Inlet module unit with pressure relief valve Electric venting valve Size ort sizes: = G/8 = 9/6-8UNF djustment: M = lastic knob C = Grub screw Setting ranges = max. 50 bar (white spring) = max. 50 bar (yellow spring) = max. 0 bar (green spring) Voltage for the electric venting valve (ab. ) S = No variants SV = Viton Y = ush button emergency (see page ) S = Rotary emergency (see page ) J = M Junior connection (see page 06) CX = Deutsch connection with bidirectional diode (see page 06) Serial No. () Setting referred to the maximum pressure reached from the relief valve. Do not exceed the maximum working pressure 50 bar. M FEURES Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight. kg ressure relief valve (CM0...) Setting range (): Spring Spring Spring max 50 bar max 50 bar max 0 bar Electrical venting valve (CR04..N..) Max. excitation frequency Hz Duty cycle 00% ED ype of protection (in relation to the connector usad) I65 () he minimum permissible setting pressure depending on the spring: see curves. ab. - Voltage - Coil 8W/W () L VDC M 4 VDC N 48 VDC.6 VDC Z () 0 VDC RC X () 05 VDC RC W (4) Without coil () Connector to be ordered separately, see page 05; Coils technical data, see page 06; () With rectifier: 5 VC/50Hz - 0 VC/60Hz () With rectifier: 0 VC/50Hz - 40 VC/60Hz (4) erformance are guaranteed only using valves completed with coil IE/FE000/0/0

FE0 DIGRMS - RESSURE RELIEF VLVE RESSURE-FLOW RE MIN.SEING RESSURE 60 0 00 80 80 (bar) 40 00 60 40 = max 50 bar 0 = max 50 bar 80 0 = max 0 bar 40 0 0 5 0 5 0 5 0 5 40 Q (l/min) (bar) 60 0 0 5 0 5 0 5 0 5 40 Q (l/min) Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. DIGRMS - ELECRICL VENING VLVE RESSURE DROS LIMIS OF USE 6 00 (bar) 4 0 8 (bar) 50 00 50 6 4 0 0 0 0 0 40 Q (l/min) 00 50 0 0 0 0 0 40 Q (l/min) Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. OVERLL DIMENSIONS SNDRD EMERGENCY C = Grub screw M = lastic knob VRINS S Emergency rotary Y Emergency with push button J M Junior CX Deutsch with diode 9 Ø0,5 Corsa (Stroke) 8 max Ø0 Ø0 9,5 60.8 47.8 8.5.5 6.5 40.5 9 0.5 IE/FE000/0/0

FE0S INLE MODULE UNIS WIH SIDE ORS, RESSURE RELIEF VLVE ND ELECRICL VENING VLVE Inlet module units FE0S with side ports, CM0 adjustable pressure relief valve and electrical venting valve CR048N normally open supplied with emergency control. Manual adjustment with a grub screw or plastic knob. hreaded ports - sizes G/8 ressure gauge M, G/4 Maximum fl ow 40 l/min. luminum body. Connector to be ordered separately, see page 05. HYDRULIC SYMOL ORDERING CODE FE0 S Inlet module unit with pressure relief valve Electric venting valve and side ports Size ort sizes: = G/8 djustment: M = lastic knob C = Grub screw Setting ranges = max. 50 bar (white spring) = max. 50 bar (yellow spring) = max. 0 bar (green spring) Voltage for the electric venting valve (ab. ) S = No variants SV = Viton Y = ush button emergency (see page ) S = Rotary emergency (see page ) J = M Junior connection (see page 06) CX = Deutsch connection with bidirectional diode (see page 06) Serial No. () Setting referred to the maximum pressure reached from the relief valve. Do not exceed the maximum working pressure 50 bar. M FEURES Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight. kg ressure relief valve (CM0...) Setting range (): Spring Spring Spring max 50 bar max 50 bar max 0 bar Electrical venting valve (CR04..N..) Max. excitation frequency Hz Duty cycle 00% ED ype of protection (in relation to the connector usad) I65 () he minimum permissible setting pressure depending on the spring: see curves. ab. - Voltage - Coil 8W/W () L VDC M 4 VDC N 48 VDC.6 VDC Z () 0 VDC RC X () 05 VDC RC W (4) Without coil () Connector to be ordered separately, see page 05; Coils technical data, see page 06; () With rectifier: 5 VC/50Hz - 0 VC/60Hz () With rectifier: 0 VC/50Hz - 40 VC/60Hz (4) erformance are guaranteed only using valves completed with coil IE/FE0S00/0-06

FE0S DIGRMS - RESSURE RELIEF VLVE RESSURE-FLOW RE MIN.SEING RESSURE 60 0 00 80 80 (bar) 40 00 60 40 = max 50 bar 0 = max 50 bar 80 0 = max 0 bar 40 0 0 5 0 5 0 5 0 5 40 Q (l/min) (bar) 60 0 0 5 0 5 0 5 0 5 40 Q (l/min) Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. DIGRMS - ELECRICL VENING VLVE RESSURE DROS LIMIS OF USE 6 00 (bar) 4 0 8 (bar) 50 00 50 6 4 0 0 0 0 0 40 Q (l/min) 00 50 0 0 0 0 0 40 Q (l/min) Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. OVERLL DIMENSIONS SNDRD EMERGENCY C = Grub screw M = lastic knob VRINS S Emergency rotary Y Emergency with push button J M Junior CX Deutsch with diode 9 Ø0,5 Corsa (Stroke) 8 max Ø0 Ø0 9,5 60.8 47.8 8.5.5 6.5 40.5 9 0.5 IE/FE0S00/0-06 4

CDC DIRECIONL CONROL NKLE VLVE WIH 09 COILS Directional control bankable valve CDC with single or double solenoid. Centring achieved by means of calibrated length springs which immediately reposition the spool in the neutral position when the electrical signal is shut off. Different springs used for each spool to improve the valve performance. Emergency control. ody for parallel or series connections hreaded ports sizes G/8 or 9/6-8UNF (SE 6), with or without LS line. Coils protection I65 ower supply DC or C (with rectifier). Standard connectors DIN 4650 ISO 4400, M Junior, flying leads and Deutsch Maximum flow until 0 l/min. Cast iron zinc plated body. Connector to be ordered separately, see page 05. ORDERING CODE FEURES CDC E Directional control bankable valve (with 09 coil) Size ody type (tab. ) Electrical operator Spool (tab.) Mounting (tab.) Max. pressure ports /// 50 bar Max. Flow 0 l/min Max excitation frequency Hz Duty cycle 00% ED Hydraulic fluid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (filter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight with one DC solenoid Weight with two DC solenoids.5 kg.50 kg Voltage (tab.4) Variants (tab.5) Serial No. Calibrated diaphragms on line, see page 04. IE/CDC00/0-07 5

CDC ORDERING CODE ab. - ody type Code ody orts G/8 parallel orts 9/6-8UNF parallel D () orts G/8 series E () orts 9/6-8UNF series ttachment style G arallel presetting for modular valves ttachment style H () Series presetting for modular valves I orts 9/6-8UNF parallel - LS vers. L orts G/8 parallel - LS vers. ttachment style, parallel-ls vers. M resetting for modular valves Special connection -- S (see outlet module unit FUS pag.55) orts G/8 parallel - - closed U (not require the outlet module units) ab. - Standard spools wo solenoids,spring centred C Mounting Code Covering ransient position 0 + 0-0 + 04 () - One solenoid, side E Mounting Code Covering ransient position 0 + 0-0 + 04 () - 5-6 + ab. - Mounting Code C E F G () H () ab.4 - Coils 09 voltage (7) Code ab.5 - Variants (7-8) Code S SV Variant No variant Viton LF () Emergency control lever (see page 4) LR Emergency control lever 80 rotated (see page 4) ES Emergency button (see page 4) (9) Rotary emergency button (see page 4) R5 (9) Rotary emergency b. 80 (see page 4) Voltage Max. winding temperature (mbient temperature 5 C) First elem. for series connec. J (0) M Junior connection (see page 07) FL (0) Coil with flying leads 50 mm (see page 07) Rated power W LD (0) Coil with flying leads 0 mm and integrated diode (see page 07) CX (0) Deutsch connecection with bidirectional diode (see page 07) Resistance @ 0 C (Ohm) ±7% L Vdc C 7 5. M 4 Vdc C 7. N () 48 Vdc C 7 85. Z (4) 0 Vdc C 7 9 () 0 Vdc C 7 448 X (5) 05 Vdc C 7 577 W (6) Symbol Without coils One solenoid, side F Mounting Code Covering ransient position 0 + 0-0 + 04 () - 5-6 + () For series connection configuration, a special individual bankable valve CDCE04 ( or G parallel body type only, with spool 04 type, variant) must always be used as first element. For other individual bankable valve must use body D E or H connector series type with spool 04 only. () Specials with price increasing () Special voltage (4) Require connector with rectifier: 5 VC/50Hz - 0 VC/60Hz (5) Require connector with rectifier: 0 VC/50Hz - 40 VC/60Hz (6) erformance are guaranteed only using valves completed with coil (7) Connector to be ordered separately, see page 05; Coils technical data, see page 07; Voltage codes are not stamped on the plate, their are readable on the coils (8) Other variants available on request (9) ightening torque max. 6 9 Nm (CH n. ) (0) vailable in V or 4V DC voltage only () For the body type G - H - M order LR variant (Emergency control lever80 rotated) IE/CDC00/0-07 6

O O O O O O O O O O O O O O CDC HYDRULIC SYMOLS CDC... CDC... CDC D... CDC E... CDC G... CDC H... LS LS LS CDC I... CDC L... CDC M... CDC S... CDC U... HYDRULIC SYMOLS ND INSRUCION OF CONNECION RLLEL CONNECION SERIES CONNECION Special element CDCE04 VM Special closing plug For series connection configuration, a special individual valve bank section (CDCE04) must always be used as first element (see ordering code page 5). IE/CDC00/0-07 7

CDC RESSURE DROS - DIRECIONL CONROL NKLE VLVE (bar) 0 8 0 4 6 5 67 4 8 9 0 0 5 0 5 0 5 0 Q (l/min) Spool Connections type / passing 0 4 4 4 4 9 0 (p) 7 7 6 6 7 9 0 (s) 7 7 6 6 8 0 4 4 6 6 9 04 (p) 5 9 04 (s) 5-6 (E) 6 6 0 0 9 5-6 (F) 6 6 5 5 9 Curve No. he diagram at the side shows the pressure drop curves for spools during normal usage. he fluid used is a mineral oil with a viscosity of 46 mm²/s at 40 C ; the tests have been carried out at a fluid temperature of 40 C. (p) arallel connections (s) Series connections (E) Mounting E (F) Mounting F LIMIS OF USE (MOUNING C-E-F) (bar) 50 00 50 00 50 0 0 5 0 5 0 5 0 Q (l/min) 4 Spool type Curve No. 0 0 0 04 5-6 (4) (4) = 5 and 6 spools used as or way, follow the curve No. 4 he tests have been carried out with solenoids at operating temperature and a voltage 0% less than rated voltage with a fluid temperature of 50 C. he fluid used was a mineral oil with a viscosity of 46 mm²/s at 40 degrees C. he values in the diagram refer to tests carried out with the oil flow in two directions simultaneously (e.g. from to and at the same time to ). In the cases where valves 4/ and 4/ are used with the flow in one direction only, the limits of use could have variations which may even be negative (See curve No 4 and Spool No 6 used as or ways). he tests were carried out with a counter-pressure of bar at port. NOE: he limits of use are valid for the C, E, F mounting. IE/CDC00/0-07 8

CDC OVERLL DIMENSIONS arallel body Only for LS versions O-Ring -008 90Sh x O-Ring -0 90Sh 59 = = ody "S" connection -- 0.5 0.5 55 4,5 4 9 5 6 LS 8.5 6 Single solenoid versions 49 = 69.5 = = 9.5 = N 4 6.5 = 78.5 = x O-Ring -0 90Sh N 4 Ø 6.5 5 9 6 86 54.5 40 4 46 = Manual emergency 009 = Fittings, max. tightening torque 60 Nm arallel body resetting for modular valves = 49 = = = 59 69.5 = = 78.5 = = IE/CDC00/0-07 9

O O O CDCM DIRECIONL CONROL NKLE VLVE WIH RESSURE RELIEF VLVE ND 09 COILS Connector to be ordered separately, see page 05. ORDERING CODE Directional control bankable valve CDCM with single or double solenoid and one or two pressure relief valves with adjustable setting on and/or. Centring achieved by means of calibrated length springs which immediately reposition the spool in the neutral position when the electrical signal is shut off. Different springs used for each spool to improve the valve performance. Emergency control. ody for parallel or series connections hreaded ports sizes G/8 Coils protection I65 ower supply DC or C (with rectifi er). Standard connectors DIN 4650 ISO 4400, M Junior, fl ying leads and Deutsch Maximum fl ow until 0 l/min. Cast iron zinc plated body. CDCM Directional control bankable valve with relief valve (09 coil) E Size ody type (tab. ) Electrical operator Spool (tab.) Mounting (tab.) Voltage (tab.4) ressure relief valve setting on (tab. 5) ressure relief valve setting on (tab. 5, omitted if equal to ) FEURES Max. pressure ports /// 50 bar Max. fl ow 0 l/min Max. fl ow - ressure relief valve see diagrams page Max excitation frequency Hz Duty cycle 00% ED Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight with one DC solenoid Weight with two DC solenoids.40 kg.65 kg Variants (tab.6) Serial No. Calibrated diaphragms on line, see page 04. HYDRULIC SYMOLS CDCM O.. CDCM.. CDCM N.. IE/CDCM00/0-05 0

CDCM ORDERING CODE ab. - ody type Code ody O orts G/8 parallel with relief valve on orts G/8 parallel with relief valve on N orts G/8 parallel with relief valve on and ab. - Standard spools wo solenoids,spring centred C Mounting Code Covering ransient position 0 + ab.4 - Coils 09 voltage (6) Code Voltage Max. winding temperature (mbient temperature 5 C) Rated power W Resistance @ 0 C (Ohm) ±7% L Vdc C 7 5. M 4 Vdc C 7. N () 48 Vdc C 7 85. Z () 0 Vdc C 7 9 () 0 Vdc C 7 448 X (4) 05 Vdc C 7 577 W (5) Without coils 0-0 + 04 () - One solenoid, side E Mounting Code Covering ransient position 0 + 0-0 + 04 () - 5-6 + One solenoid, side F Mounting Code Covering ransient position ab.5 - ressure relief valve settings (7) Code Setting 0 0 bar 00 bar 0 50 bar ab.6 - Variants (6-8) Code Variant S No variant LF Emergency control lever (see page 4) ES Emergency button (see page 4) (9) Rotary emergency button (see page 4) R5 (9) Rotary emergency b. 80 (see page 4) J (0) M Junior connection (see page 07) FL (0) Coil with flying leads 50 mm (see page 07) LD (0) Coil with flying leads 0 mm and integrated diode (see page 07) CX (0) Deutsch connecection with bidirectional diode (see page 07) 0 + 0-0 + 04 () - 5-6 + ab. - Mounting Code C E F G () H () Symbol () Specials with price increasing () Special voltage () Require connector with rectifier: 5 VC/50Hz - 0 VC/60Hz (4) Require connector with rectifier: 0 VC/50Hz - 40 VC/60Hz (5) erformance are guaranteed only using valves completed with coil (6) Connector to be ordered separately, see page 05; Coils technical data, see page 07; Voltage codes are not stamped on the plate, their are readable on the coils (7) Other settings available on request (8) Other variants available on request (9) ightening torque max. 6 9 Nm (CH n. ) (0) vailable in V or 4V DC voltage only IE/CDCM00/0-05

CDCM HYDRULIC SYMOLS ND INSRUCION OF CONNECION RLLEL CONNECION DIGRMS - RESSURE RELIEF VLVES MX RESSURE SEING MIN.SEING RESSURE (bar) 00 50 00 50 00 50 0 0 4 5 6 Q (l/min) (bar) 60 40 0 00 80 60 40 0 0 0 4 5 6 Q (l/min) = 0 barbar = 00 bar = 0 50 bar Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. RESSURE DROS - DIRECIONL CONROL NKLE VLVE (bar) 0 8 6 4 5 4 6 7 8 0 0 5 0 5 0 5 0 Q (l/min) 9 Spool Connections type / passing 0 8 0 (p) 6 6 5 5 6 8 0 5 5 8 04 (p) 4 8 5-6 (E) 5 5 9 9 8 5-6 (F) 5 5 4 4 8 Curve No. he diagram at the side shows the pressure drop curves for spools during normal usage. he fluid used is a mineral oil with a viscosity of 46 mm²/s at 40 C ; the tests have been carried out at a fluid temperature of 40 C. (p) arallel connections (s) Series connections (E) Mounting E (F) Mounting F LIMIS OF USE (MOUNING C-E-F) (bar) 50 00 50 00 50 0 0 5 0 5 0 5 0 Q (l/min) 4 Spool type Curve No. 0 0 0 04 5-6 (4) he tests have been carried out with solenoids at operating temperature and a voltage 0% less than rated voltage with a fluid temperature of 50 C. he fluid used was a mineral oil with a viscosity of 46 mm²/s at 40 degrees C. he values in the diagram refer to tests carried out with the oil flow in two directions simultaneously (e.g. from to and at the same time to ). In the cases where valves 4/ and 4/ are used with the flow in one direction only, the limits of use could have variations which may even be negative (See curve No 4 and Spool No 6 used as or ways). he tests were carried out with a counter-pressure of bar at port. NOE: he limits of use are valid for the C, E, F mounting. (4) = 5 and 6 spools used as or way, follow the curve No. 4 IE/CDCM00/0-05

CDCM OVERLL DIMENSIONS x O-Ring -0 90Sh 59 = = 49 = = 8 5 0 9 4 6 Manual emergency N 4 Ø 6,5 6 Single solenoid versions 9,5 Fittings, max. tightening torque 60 Nm 46 6 = = = = 54,5 69,5 54,5 = = 78,5 = = IE/CDCM00/0-05

CDC / CDCM (variants) LF ND LR VRINS - EMERGENCY CONROL LEVER 8 8 7 8 59 46 66.4 45 56 46 8 hanks to his flexibility, the component is designed to be inserted between the valve body and the spool, providing total interchangeability between the different types of solenoid body valves manufactured by Dana revini. he control can be used as an emergency device in the event of power cuts. 6,5 77,5 LF variant HYDRULIC SYMOL Max operating pressure dynamic port static Max operating pressure port for series connection confi guration Mounting type Spools type CDC Weight with single solenoid CDCM Weight with double solenoid CDC CDCM 60 bar 0 bar 60 bar C - F - H 0-0 04-6. kg.6 kg.46 kg.6 kg 9 LR variant OHER VRINS ES Manual emergency Rotary emergency R5 Rotary emergency 80 J M Junior CX Deutsch with diode FL Flying leads LD Flying leads/diode 9 8 9 8 9 8 Emergency and 5, tightening torque max. 6 9 Nm (CH n. ) IE/CDC-CDCM-VR/0-06 4

CD DIRECIONL CONROL NKLE VLVE WIH D5 COILS Directional control bankable valve CD with single or double solenoid. Centring achieved by means of calibrated length springs which immediately reposition the spool in the neutral position when the electrical signal is shut off. Different springs used for each spool to improve the valve performance. Emergency control. ody for parallel or series connections hreaded ports sizes G/8 or 9/6-8UNF (SE 6), with or without LS line. Coils protection I66 ower supply DC or C (with rectifi er). Standard connectors DIN 4650 ISO 4400, M Junior, fl ying leads and Deutsch Maximum fl ow until 40 l/min. Cast iron zinc plated body. Connector to be ordered separately, see page 05. ORDERING CODE FEURES CD E Directional control bankable valve (with D5 coil) Size ody type (tab. ) Electrical operator Spool (tab.) Mounting (tab.) Max. pressure ports /// 0 bar Max. pressure port 50 bar Max. Flow 40 l/min Max excitation frequency Hz Duty cycle 00% ED Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight with one DC solenoid Weight with two DC solenoids.89 kg.778 kg Voltage (tab.4) Variants (tab.5) Serial No. Calibrated diaphragms on line, see page 04. IE/CD00/0-07 5

CD ORDERING CODE ab. - ody type Code ody orts G/8 parallel orts 9/6-8UNF parallel D () orts G/8 series E () orts 9/6-8UNF series ttachment style G arallel presetting for modular valves ttachment style H () Series presetting for modular valves I orts 9/6-8UNF parallel - LS vers. L orts G/8 parallel - LS vers. ttachment style, parallel-ls vers. M resetting for modular valves Special connection -- S (see outlet module unit FUS pag.55) orts G/8 parallel - - closed U (not require the outlet module units) ab. - Standard spools wo solenoids,spring centred C Mounting Code Covering ransient position 0 + 0-0 + 04 () - One solenoid, side E Mounting Code Covering ransient position 0 + 0-0 + 04 () - 5-6 + ab. - Mounting Code C E F G () H () Code S SV Symbol ab.4 - Coils D5 voltage (7) Code ab.5 - Variants (7-8) Variant No variant Viton LF () Emergency control lever (see page 40) LR Emergency control lever80 rotated (see page 40) ES Emergency button (see page 40) (9) Rotary emergency button (see page 40) R5 (9) Rotary emergency b. 80 (see page 40) Voltage Max. winding temperature (mbient temperature 5 C) First elem. for series connec. J (0) M Junior connection (see page 08) D (0) M Junior and integr diode (see page 08) SL (0) Coil with flying leads 75 mm (see page 08) CZ (0) Deutsch D04- connection (see page 09) Rated power W CX (0) Deutsch D04- connection and integr diode (see page 09) R6 (0) Deutsch D04- connection ecoat surface treatment (see page 09) RS () Hirschmann coil ecoat surface treatment (see page 09) Resistance @ 0 C (Ohm) ±0% L Vdc 0 C 0 4.8 M 4 Vdc 0 C 0 8.8 V () 8 Vdc 0 C 0 5.6 N () 48 Vdc 0 C 0 75. Z (4) 0 Vdc 0 C 0 40 () 0 Vdc 0 C 0 87 X (5) 05 Vdc 0 C 0 75 W (6) Without coils One solenoid, side F Mounting Code Covering ransient position 0 + 0-0 + 04 () - 5-6 + () For series connection configuration, a special individual bankable valve CDE04 ( or G parallel body type only, with spool 04 type, variant) must always be used as first element. For other individual bankable valve must use body D E or H connector series type with spool 04 only () Specials with price increasing () Special voltage (4) Require connector with rectifier: 5 VC/50Hz - 0 VC/60Hz (5) Require connector with rectifier: 0 VC/50Hz - 40 VC/60Hz (6) erformance are guaranteed only using valves completed with coil (7) Connector to be ordered separately, see page 05; Coils technical data, see page 08-09; Voltage codes are not stamped on the plate, their are readable on the coils (8) Other variants available on request (9) ightening torque max. 6 9 Nm (CH n. ) (0) vailable in V or 4V DC voltage only. () vailable in V, 4V, 8V or 0V DC voltage only () For the body type G - H - M order LR variant (Emergency control lever80 rotated) IE/CD00/0-07 6

O O O O O O O O O O O O O O CD HYDRULIC SYMOLS CD... CD... CD D... CDC E... CD G... CD H... LS LS LS CD I... CD L... CD M... CDC S... CDC U... HYDRULIC SYMOLS ND INSRUCION OF CONNECION RLLEL CONNECION SERIES CONNECION Special element CDE04 VM Special closing plug For series connection configuration, a special individual valve bank section (CDE04) must always be used as first element (see ordering code page 5). IE/CD00/0-07 7

CD RESSURE DROS - DIRECIONL CONROL NKLE VLVE (bar) 0 8 6 4 0 8 6 4 0 0 98 0 5 0 5 0 5 0 5 40 Q (l/min) 7 6 5 4 Spool Connections type / passing 0 6 6 6 6 0 (p) 5 5 4 4 0 (s) 5 5 5 5 0 6 6 5 5 04 (p) 9 0 8 8 4 04 (s) 9 9 8 8 5 5-6 (E) 5 7 5 9 5-6 (F) 7 5 9 5 Curve No. he diagram at the side shows the pressure drop curves for spools during normal usage. he fluid used is a mineral oil with a viscosity of 46 mm²/s at 40 C ; the tests have been carried out at a fluid temperature of 40 C. (p) arallel connections (s) Series connections (E) Mounting E (F) Mounting F LIMIS OF USE (MOUNING C-E-F) (bar) 50 00 50 00 50 00 50 0 0 0 0 0 40 Q (l/min) Spool type Curve No. 0 0 0 04 5 6 () = 6 spools used as or way, follow the curve No. he tests have been carried out with solenoids at operating temperature and a voltage 0% less than rated voltage with a fluid temperature of 50 C. he fluid used was a mineral oil with a viscosity of 46 mm²/s at 40 degrees C. he values in the diagram refer to tests carried out with the oil flow in two directions simultaneously (e.g. from to and at the same time to ). In the cases where valves 4/ and 4/ are used with the flow in one direction only, the limits of use could have variations which may even be negative (See curve No and Spool No 6 used as or ways). he tests were carried out with a counter-pressure of bar at port. NOE: he limits of use are valid for the C, E, F mounting. IE/CD00/0-07 8

CD OVERLL DIMENSIONS arallel body Only for LS versions O-Ring -008 90Sh 59 = = x O-Ring -0 90Sh ody "S" connection -- 0.5 0.5 LS 4.5 5 x O-Ring -0 90Sh N 4 Ø6,5 4 5 9 9 4 4 6 6 56 6 = 49 = N 4 Ø6.5 80 69.5 Single solenoid versions = = 9.5 = = 55 80 46 = = Ø45 Manual emergency 009 0.5 = = Fittings, max. tightening torque 60 Nm arallel body resetting for modular valves = 49 = = = = 59 80 69.5 80 9.5 = = = IE/CD00/0-07 9

CD (variants) LF ND LR VRINS - EMERGENCY CONROL LEVER 8 8 77 08 max 66 max 6.5 Ø.5.5 7 Ø 0 8.5 8.5 8.5 98.5 0 7 66.7 5.7 66.5 hanks to his flexibility, the component is designed to be inserted between the valve body and the spool, providing total interchangeability between the different types of solenoid body valves manufactured by Dana revini. he control can be used as an emergency device in the event of power cuts. 6,5 0,5 8,5 LF variant HYDRULIC SYMOL Max operating pressure dynamic port static Max operating pressure port for series connection confi guration Mounting type Spools type Weight with single solenoid Weight with double solenoid 60 bar 0 bar 60 bar C - F - H 0-0 - 0 04-6.5 kg.74 kg 9 LR variant OHER VRINS ES Manual emergency Rotary emergency R5 Rotary emergency 80 J M Junior D M Junior + Diode CZ Deutsch D04- R6 Deutsch D04- ecoat treatment SL Flying leads RS ecoat treatment 5.7 65.7 54. 54. 54. 54, Emergency and 5, tightening torque max. 6 9 Nm (CH n. ) IE/CD-VR/0-06 40

CX SOLENOID OERING ROORIONL CONROL NKLE VLVES roportional control bankable valves CX with single or double solenoid. Emergency control. ody for parallel connections hreaded ports sizes G/8 or 9/6-8UNF (SE 6), with or without LS line. Coils protection I66 Standard connectors DIN 4650 ISO 4400, M Junior, fl ying leads and Deutsch Regulated fl ow rate / 0 / 5 / 0 l/min Cast iron zinc plated body. FEURES Connector to be ordered separately, see page 05. ORDERING CODE CX N roportional control bankable valve Size = Single solenoid C = Double solenoid ody type: = orts G/8 parallel = orts 9/6-8UNF parallel G = resetting for modular valves (parallel) L = orts G/8 parallel (LS version) ype of spool 0 = Symmetrical fl ow path control (see symbols table) Nominal flow with Dp 5 bar from to, = l/min = 0 l/min = 5 l/min 4 = 0 l/min Max. current at solenoid (): E =.5 - Special coil (9 VDC) F =.76 ( VDC) G = 0.88 (4 VDC) Variants (-): S = No variant SV = Viton ES = Emergency button () = Rotary emergency () R5 = Rotary emergency 80 () J = Coil with M Junior connection () CZ = Coil with Deutsch connection D04- () Serial No. () Coils technical data, see page. Voltage codes are not stamped on the plate, their are readable on the coils () Connector to be ordered separately, see page 05; () Emergency (see page 4) Max. operating pressure ports // 0 bar Max. operating pressure ports (ressure dynamic allowed for millions of cycles) 50 bar Nominal fl ow with Dp 5 bar from to, / 0 / 5 / 0 l/min Relative duty cycle Continuous 00% ED ype of protection (Hirschmann coil) I 66 Fluid viscosity 0 500 mm²/s Fluid temperature -0 C 75 C mbient temperature -0 C 60 C Max. contamination level (fi lter ß0 75) ISO 4406:999: class 9/7/4 NS 68: class 8 Weight with single solenoid (CX..) Weight with double solenoid (CXC..).89 kg.778 kg Solenoid @ 9Vdc @ Vdc @ 4Vdc Current supply WM (pulse width modulation) Max. current solenoid.5.76 0.88 Solenoid coil resistance at 5 C (77 F).5 Ohm 4.0 Ohm 6.0 Ohm WM or superimposed dither frequency 00 50 Hz Operating specifications are valid for fluid with 46 mm²/s viscosity at 40 C, using the specified Dana revini electronic control units. ccessories REMSR.. REMDR.. CES... MV JMEI0M7000 JMIU0M7008 HYDRULIC SYMOLS O Card type control for single and double solenoid Electronic amplifi er plug version for signle solenoid Electronic module for integrate control of proportional valves and ON/OFF Joystick with standard handle Joystick erson present handle O LS CX... CX C... CX CL... O IE/CX00/0-06 4

CX 5 50 0 00 Q (l/min) 5 0 (bar) 50 00 5 50 0 0 0 0 0 40 50 60 70 80 90 00 I (%) 0 0 5 0 5 0 5 0 Q (l/min) max 66.5 Ø.5.5 7 Ø 0 8.5 8.5 8.5 HYDRULIC SYMOLS ND INSRUCION OF CONNECION RLLEL CONNECION DIGRMS INU SIGNL CX.0N4... OWER LIMIS RNSMIED CX.0N4... he fluid used is a mineral based oil with a viscosity of 46 mm²/s at 40 C. he tests have been carried out at with a fluid of a 40 C. VRINS ES Manual emergency Rotary emergency R5 Rotary emergency 80 max 6 98.5 0 7 Emergency and 5, tightening torque max. 6 9 Nm (CH n. ) IE/CX00/0-06 4

CX OVERLL DIMENSIONS arallel body Only for LS versions O-Ring -008 90Sh x O-Ring -0 90Sh 59 = = LS 4.5 4 x O-Ring -0 90Sh N 4 Ø6,5 4 5 9 4 56 6 5 9 6 49 N 4 Ø6.5 = = 80 69.5 = = 9.5 = = Single solenoid versions 55 80 46 = = Ø45 Manual emergency 009 0.5 = = Fittings, max. tightening torque 60 Nm arallel body resetting for modular valves = 49 = = = = 59 80 69.5 80 9.5 = = = IE/CX00/0-06 4

CXQ OEN LOO ROORIONL RESSURE COMENSED NKLE FLOW REGULORS Open loop proportional fl ow regulator way compensated with priority function. Regulate the fl ow in proportion to an applied electrical current (REM, MV or CES power amplifi er). Flow regulation is independent both from load OU port and pump fl ow variations. Load compensation is achieved by a spool compensator, which holds the pressure drop constant across the proportional spool. Emergency control. Coils protection I66 Standard connectors DIN 4650 ISO 4400, M Junior, and Deutsch Regulated fl ow rate 5 / 0 l/min Cast iron zinc plated body. Connector to be ordered separately, see page 05. ORDERING CODE CXQ C D Open loop way proportional compensated flow regulator for module units and bankable valves Size way compensation = way (external excedence Line/ priority function) = way (internal excedence to ) Nominal flow rates H = 5 l/min I = 5 l/min With decompression Max. current at solenoid (): E =.5 - Special coil (9 VDC) F =.76 ( VDC) G = 0.88 (4 VDC) Variants (-): S = No variant L7 = emergency lever () = Rotary emergency () R5 = Rotary emergency 80 () J = Coil with M Junior connection () CZ = Coil with Deutsch connection D04- () Serial No. FEURES Max. operating pressure ports in / out / E 50 bar Max. operating pressure ports (ressure dynamic allowed for millions of cycles) 50 bar Regulated fl ow rate 5 / 5 l/min Decompression drain fl ow max 0.7 l/min Relative duty cycle Continuous 00% ED ype of protection (Hirschmann coil) I 66 Flow rate gain See diagram Input signal fl ow Fluid viscosity 0 500 mm²/s Fluid temperature -0 C 75 C mbient temperature -0 C 60 C Max. contamination level (fi lter ß0 75) ISO 4406:999: class 9/7/4 NS 68: class 8 Weight version CXQC.. Weight version CXQC...5 kg.75 kg Solenoid @ 9Vdc @ Vdc @ 4Vdc Current supply WM (pulse width modulation) Max. current solenoid.5.76 0.88 Solenoid coil resistance at 5 C (77 F).5 Ohm 4.0 Ohm 6.0 Ohm WM or superimposed dither frequency 00 50 Hz Operating specifications are valid for fluid with 46 mm²/s viscosity at 40 C, using the specified Dana revini electronic control units. ccessories REMSR.. CES... MV JMEI0M7000 JMIU0M7008 HYDRULIC SYMOLS Card type control for single solenoid Electronic amplifi er plug version for signle solenoid Electronic module for integrate control of proportional valves and ON/OFF Joystick with standard handle Joystick erson present handle E CXQC.. CXQC.. IN OU IN OU () Coils Dati tecnici technical bobine, data, vedi see pag. page 0.. Le Voltage tensioni codes non are sono not stampigliate stamped on sulle the plate, targhette, their are ma indicate readable sulla on the bobina coils () Connettori Connector to da be ordinare ordered separatamente, separately, see vedi page pag. 05; 97; () Emergenze, Emergency (see vedi page pag. 46) = lind IE/CXQ00/0-06 44

CXQ DIGRMS INU SIGNL FLOW FLOW RE CK RESSURE ON RIORIY LINE FLOW RE CK RESSURE ON SECONDRY LINE 5 0 5 4 4 Q (l/min) 0 5 Q (l/min) 6 Q (l/min) 6 0 8 8 5 0 0 0 0 0 40 50 60 70 80 90 00 I (%) 0 0 50 00 50 00 50 (bar) 0 0 50 00 50 00 50 (bar) 0 UM FLOW IN CXQC... 0 UM FLOW IN CXQC... (bar) 5 0 (bar) 5 0 = CXQCI... = CXQCH.. 5 0 0 5 0 5 0 5 0 Q (l/min) 5 0 0 5 0 5 0 5 0 Q (l/min) he fluid used is a mineral based oil with a viscosity of 46 mm²/s at 40 C. he tests have been carried out at with a fluid of a 40 C. OVERLL DIMENSIONS CXQC... O-Ring -008 90Sh x O-Ring -0 90Sh 59 = = N 4 Ø 6.5 6 9 56 4 4 49 = = Ø45 80 6 69.5.5 = = IE/CXQ00/0-06 45

CXQ OVERLL DIMENSIONS CXQC... 59 = = 4 x O-Ring -0 90Sh N 4 Ø 6.5 4 49 = = 8.5 max 66.5 8.5 max 6 Ø 40.5.5 7 Ø 0 54.5 86.5 6 5 9 4 G /8" Ø45 6 9.5.5 65 80 6 69.5 = =.5 VRINS L7 Emergency lever 8.5 Rotary emergency R5 Rotary emergency 80 70,5 0 7 4.5 Emergency and 5, tightening torque max. 6 9 Nm (CH n. ) IE/CXQ00/0-06 46

FI INERMEDIE ELEMEN Intermediate element FI with pass through and lines. Suggested in assemblies with more than 8 elements in order to give better support and stability. Maximum flow 40 l/min. luminum body. FEURES HYDRULIC SYMOL Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fluid DIN 554 Mineral oils Fluid viscosity 0 500 mm²/s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (filter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.4 kg ORDERING CODE OVERLL DIMENSIONS FI Intermediate element Size Standard connection 7 00 = No variant V = Viton 70 59 4 Serial No. Mounting kit (screws and tie rods)contact our customer service. N 4 M6 N 4 M6 49 x O-RING -0 90Sh IE/FI00/0-05 47

FIL INERMEDIE ELEMEN WIH LS LINE Intermediate element FIL with pass through - and LS lines. Suggested in assemblies with more than 8 elements in order to give better support and stability. Maximum fl ow 40 l/min. Cast iron zinc plated body. FEURES HYDRULIC SYMOL LS Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm²/s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.4 kg ORDERING CODE OVERLL DIMENSIONS FI Intermediate element Size 7 L LS line 70 00 = No variant V = Viton 59 4 0 4 70 4,5 Serial No. O-RING -00 90Sh N 4 M6 N 4 M6 Mounting kit (screws and tie rods)contact our customer service. 49 x O-RING -0 90Sh IE/FIL00/0-05 48

FIR INERMEDIE ELEMEN WIH RESSURE REDUCING VLVE Intermediate element FIR provide a pilot-operated pressure reducing valve CVR0 est coupling Feed a secondary branch of a circuit at a lower pressure, guaranteeing minimum variation of the set pressure with fl ow alterations. Manual adjustment with a grub screw or plastic knob. Maximum fl ow 40 l/min. luminum body. FEURES HYDRULIC SYMOL LS M Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.7 kg ORDERING CODE ressure reducing valve (CVR0...) Setting range (): Spring max 60 bar Spring max 0 bar Spring max 50 bar () he minimum permissible setting pressure depending on the spring: see curves. FI Intermediate element OVERLL DIMENSIONS Size C R ressure reducing valve 49 djustment: M = lastic knob C = Grub screw 6,5 max 90 9 Setting ranges = max. 60 bar (white spring) = max. 0 bar (yellow spring) = max. 50 bar (green spring) 55 4 O-RING -00 90Sh x O-RING -0 90Sh 8 9,5 00 = No variant V = Viton Serial No. C = Grub screw M = lastic knob V 70 max 49 59 hreaded test coupling M6x N 4 Ø 6,5 RESSURE-FLOW OF RELIEVING MIN.SEING RESSURE RESSURE-FLOW RE (bar) 00 75 50 5 00 75 50 5 00 75 50 5 0 0 5 0 45 60 75 90 Q (l/min) (bar) 40 5 0 5 0 5 0 5 0 0 5 0 45 60 75 90 Q (l/min) (bar) 00 75 50 5 00 75 50 5 00 75 50 5 0 0 5 0 45 60 75 90 Q (l/min) = max 60 bar = max 0 bar = max 50 bar Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. IE/FIR00/0-05 49

CDCR DIRECIONL CONROL VLVE CONNECION - FOR INERMEDIE ELEMEN FI Directional control valve CDCR module with body type R can be assembled with intermediate module FI, to defi ne an hydraulic scheme that can select the functions ahead or behind this module. s shown in the example scheme, when the coil on side a is energised the fl ow is delivered to the sections behind this module CDCR, instead when the coil on side b is energised the fl ow is delivered to the sections ahead. Emergency control. Coils protection I65 ower supply DC or C (with rectifi er). Standard connectors DIN 4650 ISO 4400, M Junior, fl ying leads and Deutsch Maximum fl ow until 0 l/min. Cast iron zinc plated body. FEURES Connector to be ordered separately, see page 05. HYDRULIC SYMOL Max. pressure ports /// 50 bar Max. Flow 0 l/min Max excitation frequency Hz Duty cycle 00% ED Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight.50 kg ORDERING CODE CDC Directional control valve (with 09 coil) Size R ody type E Electrical operator 0 Spool (tab.) C Mounting (tab.) Voltage (tab.) Variants (tab.) Serial No. (bar) (bar) RESSURE DROS 0 8 6 4 0 0 5 0 5 0 5 0 LIMIS OF USE 50 00 50 00 50 Q (l/min) 0 0 5 0 5 0 5 0 Q (l/min) 4 Curve Connections 4 4 / passanti Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. he tests have been carried out with solenoids at operating temperature and a voltage 0% less than rated voltage with a fluid temperature of 50 C. he fl uid used was a mineral oil with a viscosity of 46 mm²/s at 40 degrees C. he values in the diagram refer to tests carried out with the oil flow in two directions simultaneously (e.g. from to and at the same time to ). In the cases where valves 4/ and 4/ are used with the flow in one direction only, the limits of use could have variations which may even be negative. he tests were carried out with a counter-pressure of bar at port. IE/CDCR00/0-06 50

CDCR ORDERING CODE ab. - Standard spools ab. - Variants (5-6) wo solenoids,spring centred C Mounting Code Covering ransient position 0 - ab. - Coils 09 voltage (5) Code Voltage Max. winding temperature (mbient temperature 5 C) Rated power W Resistance @ 0 C (Ohm) ±7% L Vdc C 7 5. M 4 Vdc C 7. N () 48 Vdc C 7 85. Z () 0 Vdc C 7 9 () 0 Vdc C 7 448 X (4) 05 Vdc C 7 577 W (4) Without coils Code S SV Variant No variant Viton LF Emergency control lever (see page 4) LR Emergency control lever 80 rotated (see page 4) ES Emergency button (see page 4) (7) Rotary emergency button (see page 4) R5 (7) Rotary emergency b. 80 (see page 4) First elem. for series connec. J (8) M Junior connection (see page 07) FL (8) Coil with flying leads 50 mm (see page 07) LD (8) Coil with flying leads 0 mm and integrated diode (see page 07) CX (8) Deutsch connecection with bidirectional diode (see page 07) EXMLE WIH VLVE CDCR ND INERMEDIE ELEMEN FI () Special voltage () With rectifier: 5 VC/50Hz - 0 VC/60Hz () With rectifier: 0 VC/50Hz - 40 VC/60Hz (4) erformance are guaranteed only using valves completed with coil (5) Connector to be ordered separately, see page 05; Coils technical data, see page 07; Voltage codes are not stamped on the plate, their are readable on the coils (6) Other variants available on request (7) ightening torque max. 6 9 Nm (CH n. ) (8) vailable in V or 4V DC voltage only CDCR FI OVERLL DIMENSIONS x O-Ring -0 90Sh 0.5 59 = = 4 8.5 55 9 5 6 = 49 = 69.5 = = = 78.5 = N 4 6.5 009 46 = Manual emergency = IE/CDCR00/0-06 5

FI INERMEDIE ELEMEN FOR VLVE CDCR Intermediate element FI for valve CDCR to connect to lines Maximum fl ow 40 l/min. luminum body. FEURES HYDRULIC SYMOL Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm²/s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.4 kg ORDERING CODE OVERLL DIMENSIONS FI Intermediate element Size For valve CDCR 70 59 00 = No variant V = Viton 4 60 Serial No. 0,5 49 x O-RING -0 90Sh 5 IE/FI00/0-05 5

FU OULE MODULE UNIS Outlet module units FU. hreaded ports () sizes G/8 or 9/6-8UNF. Outlet modules without ports only for parallel connections Maximum fl ow 40 l/min. luminum body. FEURES Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0. kg HYDRULIC SYMOLS OVERLL DIMENSIONS 70 FU00 FU00 5 FU00 ORDERING CODE FU 00 Otulet module unit Size ort size: For outlet module without ports is not required (only for parallel style) = G/8 = 9/6-8UNF No variant Serial No. 60 60 5 4 0 4 49 59 70 49 59 4 n. 4 fori Ø 6.5 FU00 n. 4 fori Ø 6.5 0 n. M6 IE/FU00/0/0 5

FU OULE MODULE UNIS WIH SIDE ORS Outlet module units FU with side ports. hreaded ports () sizes G/4 Maximum fl ow 40 l/min. luminum body. FEURES HYDRULIC SYMOLS M Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.4 kg ORDERING CODE OVERLL DIMENSIONS FU Otulet module unit Size ort size: = G/4 00 No variant G /4" Serial No. G /4" 45 84,5 9 5 49 59 70 IE/FU00/0-05 54

O FUS OULE MODULE UNIS WIH OVERCENER ND O OR Outlet module FUS includes an overcenter valve to control the movement of a cylinder end connected to port. hreaded ports () sizes G/8 Maximum fl ow 40 l/min. luminum body. FEURES HYDRULIC SYMOLS Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.7 kg Outlet module for directional control valve CDC and CD body S (see pages 5 and 5 ). CDS... CDCS.. FUS OVERLL DIMENSIONS ORDERING CODE 59 FUS Outlet module units with overcenter and top port Size 4 55 ort size: = G/8 49 00 No variant 0 Serial No. 5 RESSURE DROS 4.5 45.5 G /8" 0 8 5 (bar) 0 70 5 0 0 0 0 0 40 Q (l/min) IE/FUS00/0-05 55

RE ND OS COMENSED VLVES pressure compensated valve maintains a constant fl ow rate across the main spool regardless of the load induced pressure, therefore the movement speed of actuator is not affected by load. Local compensator on every section allows simultaneous movement of multiple functions. Compensated valves can be of two types: pre-compensated or postcompensated. RE-COMENSED VLVE CXDH-CDH Compact and simple solution roportional control with valves CXDH or ON/OFF control with valves CDH vailable pressure rielief LSa-LSb valves on every working section Valve body with the same interface of other bankable valves (for example ON/OFF valves type CD-CDC and CD5) If the total amount of fl ow required by single function exceed the available pump fl ow (fl ow saturation) then the function with lower load will have priority, and function with higher load will stop atented LS LS LS CXDH. proportional LS CDH. on/off OS-COMENSED VLVE (FLOW SHRING) CFS If fl ow saturation occurs then the function will proportionally reduce the fl ow (Flow Sharing) and will continue the movement his solution permits high effi ciency and energy saving Valve body with the same interface of other bankable valves (for example ON/OFF valves type CD-CDC and CD5) CFSC.0.. IE/NK-COM/0-05 56

RE ND OS COMENSED VLVES CXDH proportional valves with FEH0Q inlet module for Fixed Displacement pump x M6-6H x M6-6H 54 9 54 fixing holes mounting without fixing feet tighten the screws to a torque of 0 Nm No elements mm mm C mm D mm 04 7 09 50 7 55 67 4 96 6 0 5 4 09 47 59 6 88 55 9 405 7 4 40 49 45 8 80 447 485 497.5 99.5 95 90 7.5 (5) fixing feet available on request LS LS GLS 7 0 C D LS LS CXDH Flow Sharing valves with FEH0Q inlet module x M6 9 x M6 9 54 fixing holes mounting without fixing feet tighten the screws to a torque of 0 Nm No elements mm mm C mm 4 04 9 80 50 8 4 6 96 84 5 7 4 0 6 8 88 76 7 64 4 4 8 40 80 468,5 95 70 96, fixing feet available on request 49,5 LS GLS X C IE/NK-COM/0-05 57

Composition form 4 6 8 5 7 0 6 5 4 7 9 5 7 SIZE 6 valves CXDH, CDH, CFS can be assembled with: - valves CDC, CD, CX (page 6); - with SIZE 0 valves CD5 (page 8); - with proportional directional valves HV4 (see catalogue cod. DOC00079) using the interface HSIF (page 00). o obtain the best performances, we suggest to assemble the working sections with higher flow rate near the inlet module, leaving the ones with lower flow at the end of the assembled valve. Ref. ype Descriprion age FEH0Q OEN CENER inlet module for fixed displacement pumps 59 FEH0LS CLOSED CENER inlet module for variable displacement load sensing pumps 6 FEH5Q OEN CENER inlet module with compensator for fixed displacement pumps 6 4 CXDH ROORIONL pre compensated valves 65 CXDH / CDH (variants) 7 5 CDH ON/OFF pre compensated valves 69 CXDH / CDH (variants) 7 6 CXDH ody G-M for modular valves 65 7 CFS ost compensated FLOW SHRING valve High efficiency energy saving 74 CFS (variants) 77 8 CFS ody G for modular valves 74 9 FIHL Intermediate element for pre and post compensated valves 78 0 FUH Outlet module units 79 CMF Modular elements with ports - 94 CMM Modular max. pressure bankable valves 97 HSIF Interface for proportional directional valves HV4 00 4 Mounting kit 0 5 Fixing feet 0 6 Connectors 05 7 Coils 06 How to order o order the assembly, specify the codes in progressive order (inlet, valves, outlet, mounting kit, feet). See example page 4. For any further special version not shown in this catalogue, please contact our echnical Department. IE/NK-COM/0-08 58

FEH0Q OEN CENER INLE MODULE FOR FIXED DISLCEMEN UMS Open center inlet module units FEH0Q for fi xed displacement pumps with pressure relief valve CM-MC/MS and electrical venting valve CR04. Includes a pressure compensated load sensing signal bleed to minimize system losses even at high operating pressures. Signal bleed can be closed in case it not required. Manual adjustment with a grub screw. hreaded ports - sizes G/ Maximum fl ow 80 l/min. Cast iron zinc plated body. HYDRULIC SYMOL LS GLS Connector to be ordered separately, see page 05. ORDERING CODE X FEH0 Q C Inlet module units with pressure relief valve Electrical venting valve ressure compensator element Size orts G/ djustment: C = Grub screw Setting ranges: = 5 90 bar = 75 90 bar = >50 bar Voltage venting valve (): L = Vdc M = 4 Vdc N = 48 Vdc 0 = Without electrical venting valve (plugged) Variants (-): S = No variants SV = Viton Y = ush button emergency () S = Rotary emergency () J = M Junior connection W (see page 06) CX = Deutsch connect. bidirectional diode (see page 06) Serial No. FEURES X predisposition for LS bleed plug Max. operating pressure 00 bar Setting ranges for pressure relief valve Spring : 5 90 bar Spring : 75 90 bar Spring : >50 bar Max. fl ow 80 l/min (see charateristic curves) Fluid viscosity 0 500 mm²/s Max LS bleed fl ow 0.5 l/min Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight.9 kg Max. excitation frequency Hz Duty cycle 00% ED ype of protection (in relation to the connection used) I65 o obtain a correct compensation the inlet flow must be 8% greater the sum of the regulated flows leed flow rate is subtracted to the energized valve working at the higher pressure. o avoid this behavior plug the bleed (see X on hydraulic scheme) CHRCERISIC CURVE Inlet module ressure Drops () Coils technical data, see page 06) Voltage codes are not stamped on the plate, their are readable on the coils () Connector to be ordered separately, see page 05; Other variants available on request. () Emergency (see page 60 IE/FEH0Q00/0-06 59

FEH0Q OVERLL DIMENSIONS holes for optional fixing feets predisposition to plug load sensing bleed standard emergency VRINS S Emergency rotary Y Emergency with push button J M Junior CX Deutsch with diode 9 Ø0,5 Corsa (Stroke) 8 max Ø0 Ø0 9,5 60.8 47.8 8.5.5 6.5 40.5 9 0.5 IE/FEH0Q00/0/0 60

FEH0LS CLOSED CENER INLE MODULE FOR VRILE DISLCEMEN LOD SENSING UMS Closed center inlet module units FEH0LS for variable displacement Load Sensing pumps with pressure relief valve CM0 and a pressure compensated load sensing signal bleed to minimize system losses even at high operating pressures. Signal bleed can be closed in case it is not required. Manual adjustment with a grub screw. hreaded ports - sizes G/ or 7/8 4UNF; LS ports, G/4 or 7/6 0UNF Maximum fl ow 80 l/min. Cast iron zinc plated body. HYDRULIC SYMOL LS ORDERING CODE LS FEH0 Inlet module units with pressure relief valve X LS With LS signal Size orts: = G/ (, ports) G/4 (LS port) 4 = 7/8-4UNF (, ports) 7/6-0UNF (LS port) djustment: M = lastic knob C = Grub screw Setting ranges: = max 50 bar = max 40 bar = max 50 bar Variants: 00 = No variants V = Viton Serial No. FEURES Max. operating pressure 00 bar Setting ranges for pressure relief valve Spring : max 50 bar Spring : max 40 bar Spring : max 50 bar Max. Flow 80 l/min (see charateristic curves) Max LS bleed fl ow rate 0.5 l/min Fluid viscosity 0 500 mm²/s Fluid temperature -5 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) Weight X ap for LS bleed plug ISO 4406:999: class /9/6 NS 68: class 0.9 kg leed flow rate is subtracted to the energized valve working at the higher pressure. o avoid this behavior close LS tap (see X on hydraulic scheme) RESSURE RELIEF VLVE CURVES [bar] 400 50 00 50 00 50 00 50 ressure Flow 0 0 0 0 0 40 50 60 70 80 90 00 Q [l/min] [bar] Minimun setting pressure 0 -- 8 6 4 0 8 6 4 0 0 0 0 0 40 50 60 70 80 90 00 Q [l/min] IE/FEH0LS00/0/0 6

FEH0LS OVERLL DIMENSIONS N M6 55.5 49 9 Ø 4.5 Ø.8 G/" 67 G/" 5 90 9.5 N 4 M6 6 0.5 49 = = 70 = = 47.5 6 7 5 8 54 7.5 C = djustment with grub screw M = djustment with plastic knob holes for optional fixing feets x O-RING -0 90Sh x O-RING -008 90Sh G/4" IE/FEH0LS00/0/0 6

FEH5Q OEN CENER INLE MODULE WIH COMENSOR FOR FIXED DISLCEMEN UMS Open center inlet module units FEH5Q with adjustable compensator regulator for fi xed displacement pumps with pressure relief valve CM-MC/MS and electrical venting valve CR04. Includes a pressure compensated load sensing signal bleed to minimize system losses even at high operating pressures. Signal bleed can be closed in case it not required. Manual adjustment with a grub screw. hreaded ports G/ ; G/4 Maximum fl ow 0 l/min. Cast iron zinc plated body. HYDRULIC SYMOL LS GLS Connector to be ordered separately, see page 05. X ORDERING CODE X predisposition for LS bleed plug FEH5 Q C Inlet module units with pressure relief valve and pressure compensator Electrical venting valve ressure compensator element Size = ort = G/ - ort = G/4 djustment: C = Grub screw Setting ranges: = 5 90 bar = 75 90 bar = >50 bar Voltage venting valve (): L = Vdc M = 4 Vdc N = 48 Vdc 0 = Without electrical venting valve (plugged) Variants (-): S = No variants SV = Viton Y = ush button emergency () S = Rotary emergency () J = M Junior connection W (see page 06) CX = Deutsch connect. bidirectional diode (see page 06) Serial No. (bar) 40 5 0 5 0 FEURES Max. operating pressure 0 bar Setting ranges for pressure relief valve Spring : 5 90 bar Spring : 75 90 bar Spring : >50 bar Setting compensator regulator 0 9 bar Max. fl ow 0 l/min (see charateristic curves) Fluid viscosity 0 500 mm²/s Max LS bleed fl ow 0.5 l/min Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight. kg Max. excitation frequency Hz Duty cycle 00% ED ype of protection (in relation to the connection used) I65 o obtain a correct compensation the inlet flow must be 8% greater the sum of the regulated flows leed flow rate is subtracted to the energized valve working at the higher pressure. o avoid this behavior plug the bleed (see X on hydraulic scheme) CHRCERISIC CURVE ressure drops with compensator setting at 0 and 9 bar () Coils technical data, see page 06) Voltage codes are not stamped on the plate, their are readable on the coils () Connector to be ordered separately, see page 05; Other variants available on request. () Emergency (see page 64 5 0 5 0 0 0 0 0 40 50 60 70 80 90 00 0 0 Q (l/min) IE/FEH5Q00/0-05 6

FEH5Q OVERLL DIMENSIONS G/" 4 x M6 6 G/4" 9 07 4,5 80 95 0,5 49 7 70 0 x M6 9 8 54 5 8 8 redisposition to plug load sensing bleed 74 max. 75 47,5 Compensator setting Screw Hex. 5 Nut Hex.0 Standard emergency x ORing -0 90Sh x ORing -008 90Sh Relief valve setting Screw Hex. Nut Hex.0 LS G/8" plugged G/4" plugged VRINS S Emergency rotary Y Emergency with push button J M Junior CX Deutsch with diode Ø0,5 Corsa (Stroke) 8 max Ø0 Ø0 9,5 60.8 47.8 8.5.5 6.5 40.5 9 0.5 IE/FEH5Q00/0-05 64

CXDH ROORIONL RE COMENSED VLVES Connector to be ordered separately, see page 05. ORDERING CODE atented Stackable proportional directional valves CXDH with LS signal locally compensated Used for controlling fl uid direction and fl ow rate as a function of the supply current to the proportional control solenoid. Flow regulation load indipendent. Load compensantionis achieved by a way pressure compensator wich holds, the pressure drop constants across the proportional spool. Emergency control. hreaded ports or interface for modular valves Regulated fl ow rate until 5 l/min. Standard connectors DIN 4650 ISO 4400, M Junior and Deutsch Cast iron zinc plated body. CXDH roportional compensated bankable valve Size Mounting (see table ) ody type: = orts G/8 parallel G= Interface for modular valves = orts SE 9/6-8UNF L= orts G/8 parallel with valves LS LS M= Interface for modular valves with valves LS LS ype of spool () 0 = FEURES Max. operating pressure 00 bar Max. operating pressure ports (ressure dynamic allowed for millions of cycles) 50 bar Regulated fl ow rate ( / ports) up to 5 l/min Relative duty cycle Continuous 00% ED ype of protection (Hirschmann coil) I 65 Fluid viscosity 0 500 mm²/s Fluid temperature -0 C 75 C mbient temperature -0 C 60 C Max. contamination level (fi lter ß0 75) ISO 4406:999: class 9/7/4 NS 68: class 8 Weight with single solenoid Weight with double solenoid.8 kg.77 kg N Symmetrical fl ow path control Flow rating Differential pressure p 8 = p 8 bar 4 = p 4 bar p 8bar p 4bar D 8 l/min 6 l/min 6 l/min l/min l/min 8 l/min 4 5 l/min 8 l/min Max. current at solenoid (): E =.5 (9 Vdc) - Special coil F =.76 ( Vdc) G = 0.88 (4 Vdc) Variants (): S = No variant LF/LV = Emergency control lever (see page 7) For body type G and M order LR variant (emergency lever 80 rotated) SV = Viton ES = Emergency button (4) = Rotary emergency (4) R5 = Rotary emergency 80 (4) J = M Junior coil (see page ) CZ = Deutsch D04- coil (see page ) Serial No. Calibrated diaphragms on line, see page 04. () vailable spool 0 and ports are not sealed: fluid can escape from LS line (see hydraulic scheme). () Coils technical data, see page Voltage codes are not stamped on the plate, their are readable on the coils () Connector to be ordered separately, see page 05; Other variants available on request. (4) Emergency see page7 Solenoid @ 9Vdc @ Vdc @ 4Vdc Current supply WM (pulse width modulation) Max. current solenoid.5.76 0.88 Solenoid coil resistance at 5 C (77 F).5 Ohm 4.0 Ohm 6.0 Ohm WM or superimposed dither frequency 00 50 Hz Response time 0 00% 00% 0 ms ms 40 ms ms 85 ms ms Frequency response -db (input signal 50% ±5% Vmax) Hz Hz Hz Operating specifications are valid for fluid with 46 mm²/s viscosity at 40 C, using the specified Dana revini electronic control units. (input voltage = 4V). ccessories REM.S.R... REM.D.R... Card type control for single and double solenoid CE.S... Electronic amplifi er plug version for signle solenoid MV Electronic module for integrate control of proportional valves and ON/OFF JMEI0M7000 Joystick with standard handle JMIU0M7008 Joystick erson present handle Modular valves CM (page 95) and CMM (page 97) ab. - Mounting Code C a a Symbol O O O b b IE/CXDH00/0/0 65

CXDH HYDRULIC SYMOLS LS LS LS LS LS LS LS LS CXDH0.. CXDHG0.. CXDHC0.. CXDHCG0.. LS LS LS LS CXDHM0.. CXDHL0.. CXDHCM0.. CXDHCL0.. hanks to the design of the modular body (type G), an anti-shock modular valve can works same with CXDH valve energized or de-energized (see hydraulic symbol) CHRCERISIC CURVES I-Q curves - (Curves acquired with REM card, opening stroke) Compensation curves (curves acquired with FEH0.Q inlet module) Differential ressure p = 8 bar Differential ressure p = 4 bar Differential ressure p = 8 bar Differential ressure p = 4 bar Q [l/min] 40 5 0 5 0 5 0 5 4 D Q [l/min] 0 5 0 5 0 5 4 D Q (l/min) 40 5 0 5 0 5 0 5 4 D Q (l/min) 0 5 0 5 0 5 4 D 0 0 0 0 0 40 50 60 70 80 90 00 I[%] 0 0 0 0 0 40 50 60 70 80 90 00 I [%] 0 0 50 00 50 00 50 00 p (bar) 0 0 50 00 50 00 50 00 p (bar) he fluid used is a mineral based oil with a viscosity of 46 mm²/s at 40 C. he tests have been carried out at with a fluid of a 40 C. IE/CXDH00/0/0 66

CXDH OVERLL DIMENSIONS ody type orts G/8 arallel O-RING 08/-008 90Sh O-RING 07/-0 N55 90Sh 0 4 9 6 = 59 = 4.5 O-RING 08/-008 90Sh 4 x O-RING 07/-0 N55 90Sh 59 = = 5.5 9 6 89.5 0 4 4.5 4.5 4 FORI Ø 6.5 4 HOLES 49 80 69.5 80 = = 9.5 = = 4 x Ø 5.5 = 5 = = 9 = = = = 46 8 6 = 8.5 8.5 54 8.5 8.5 5.5 4 FORI Ø 6.5 4 HOLES 49 5. = = 80 69.5 80 = = 9.5 = = 9. Coils can be rotated by 80 46 = = 4. 4. G/8" () 0.5 Fittings, max. tightening torque 60 Nm ody type G Interface for modular valves 4 x M5 = = O-RING 07/-0 N55 90Sh IE/CXDH00/0/0 67

CXDH OVERLL DIMENSIONS ody type L orts G/8 parallel with valves LS LS O-RING 08/-008 90 SH 4 x O-RING 07/-0 N55 90SH 0 4 9 6 = 59 = 4.5 79.5 09 54 80.5 8.5 49.5 4 FORI Ø 6.5 4 HOLES 5. = 46 = 45 49 = = 80 69.5 80 = = 9.5 = = G/8" 0.5 = = ody type M Interface for modular valves with valves LS LS O-RING 08/-008 90 SH 4 x O-RING 07/-0 N55 90SH 59 = = 54 4 FORI Ø 6.5 4 HOLES 45 49 = = 80 69.5 80 = = 9.5 = = 5 = = 9 = = = 46 = 8 49.5 89.5 4.5 78.5 9 6 79.5 0 4 4.5 4 xø 5.5 6 4 x M 5 = = O-RING 07/-0 N55 90SH IE/CXDH00/0/0 68

CDH ON/OFF RE COMENSED VLVES ON/OFF Compensated Valves CDH with single or double solenoid, LS signal locally compensated. Used for controlling fl uid direction and fl ow rate. Flow rate controlled by the valve predefi ned by a holed calibrated washer screwed into the port and/or. Flow regulation load independent. Load compensantion is achieved by a way pressure compensator wich holds, the pressure drop constants across the proportional spool. hreaded ports G/8 Emergency control. Standard connectors DIN 4650 ISO 4400, M Junior and Deutsch Cast iron zinc plated body. Connector to be ordered separately, see page 05. ORDERING CODE HYDRULIC SYMOL CDH On/Off compensated bankable valve Size ody type: = orts G/8 parallel LS Ø Ø E Electrical operator Spool (see table ) LS Mounting (see table ) Holed washer on port (see table ) Holed washer on port (see table ) Omit if equal to screw on port Differential pressure p 8 = p 8 bar 4 = p 4 bar Voltage (see table 4) Variants (see table 5) Serial No. Calibrated diaphragms on line, see page 04. FEURES Max. operating pressure ports // 00 bar Max. operating pressure ports (ressure dynamic allowed for millions of cycles) 50 bar Max fl ow See table Max excitation frequency Hz Duty cycle 00% ED ype of protection (Hirschmann coil) I 65 Fluid viscosity 0 500 mm²/s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight with single solenoid Weight with double solenoid.8 kg.77 kg General fl ow tolerance ±0% Operating specifications are valid for fluid with 46 mm²/s viscosity at 40 C, using the specified Dana revini electronic control units. IE/CDH00/04-07 69

CDH ORDERING CODE ab. - Spool wo solenoids, spring centred C Mounting Code a O b Covering ransient position 0 a b + () 0 a b 0 a b 04 () a b - + - () One solenoid, side E Mounting Code a O Covering ransient position ab. - Holed washer on port / Code Flow (l/min) p = 8 bar p = 4 bar 0.7. 5 4.0.0 0 7.5 5.5 5 0.0 8.0 0 4. 9.5 5 7..5 40 8.0.5 45.5 7.5 50 6.0 9.5 99 without holed washer Other flow rates available on request Interchangeable holed washer into fittings ports 0 a + () 0 a 0 a 04 () a 5 a - + - - () One solenoid, side F Mounting Code O b Covering ransient position 0 b 0 b 0 b 04 () b 5 b + - + - - () () ab.4 - Coils D5 voltage (7) Max. winding temperature Code Voltage (mbient temperature 5 C) Rated power W Resistance @ 0 C (Ohm) ±0% L Vdc 0 C 0 4.8 M 4 Vdc 0 C 0 8.8 V () 8 Vdc 0 C 0 5.6 N () 48 Vdc 0 C 0 75. Z (4) 0 Vdc 0 C 0 40 () 0 Vdc 0 C 0 87 X (5) 05 Vdc 0 C 0 75 W (6) Without coils ab.5 - Variants (7-8) Code Variant S No variant SV Viton LF Emergency control lever (see page 7) LR Emergency control lever80 rotated (vedi pagina 7) ES Emergency button (vedi pagina 7) (9) Rotary emergency button (vedi pagina 7) R5 (9) Rotary emergency b. 80 (vedi pagina 7) J (0) M Junior connection (vedi pagina 08) D (0) M Junior and integr diode (vedi pagina 08) SL (0) Coil with flying leads 75 mm (vedi pagina 08) CZ (0) Coil with Deutsch D04- (vedi pagina 09) CX (0) Deutsch D04- connection and integr diode (see page 09) ab. - Mounting Code C E F G () H () a O b a O O b Symbol O b a O () Specials with price increasing () On spool 0 and 04 and ports are not sealed: fluid can escape from LS line (see hydraulic scheme). () Special voltage (4) With rectifier: 5 VC/50Hz - 0 VC/60Hz (5) With rectifier: 0 VC/50Hz - 40 VC/60Hz (6) erformance are guaranteed only using valves completed with coil (7) Connector to be ordered separately, see page 05; Coils technical data, see page 08-09; (8) Other variants available on request. ll the variants are considered without connectors. (9) ightening torque max. 6 9 Nm (CH n. ) (0) vailable in V or 4V DC voltage only. IE/CDH00/04-07 70

CDH OVERLL DIMENSIONS O-RING 08/-008 90Sh O-RING 07/-0 N55 90Sh 59 = = 5.5 9 6 8.5 8.5 9.5 0 4 4.5 49 = = 5. G /8" 9. 4. 4. 8.5 46 = = 0.5 80 69.5 80 = 9.5 = = = Fittings, max. tightening torque 60 Nm IE/CDH00/04-07 7

CXDH / CDH (variants) LF, LR ND LV VRINS - EMERGENCY CONROL LEVER HYDRULIC SYMOL Var. LF/LR lever on the side : Var. LV lever on the side : Spool 0 available on request hanks to his flexibility, the component is designed to be inserted between the valve body and the spool, providing total interchangeability between the different types of solenoid body valves manufactured by Dana revini (). he control can be used as an emergency device in the event of power cuts. Max operating pressure port Mounting type Var. LF/LR Mounting type Var. LV Spools type Weight with single solenoid Weight with double solenoid dynamic static 60 bar 0 bar C - - F - H C- 0-0-0-04 6-7-66.4 kg.7 kg Max flow of proportional valves can be reduced compared to versions without emergency control lever when electrical operated. Max flow of proportional valves lever operated is increased compared to the max flow given when valves are electrical operated. 8 8 8 8 LF Variant (CXDH / CDH) 77 LF Variant ody L (CXDH) 58.5 6.5 0.5 8.5 7 7 0 77 6.5 0.5 8.5 LR Variant (CXDH / CDH) LR Variant M ody (CXDH) 8 8 8 8 LV Variant (CXDH / CDH) IE/CXDH-CDH-VR/0-06 7

CXDH / CDH (variants) USE OF HSIF INERFCE WIH MODULR VLVES CXDH/CDH, WIH EMERGENCY LEVER Distributor HV4 right (DX, standard) - Order modular valves CXDH/CDH variant LV, with emergency lever on the side Distributor HV4 left (SX) - Order modular valves CXDH/CDH variants LF / LR, with emergency lever on side - In this case it is not possible to mount the modular valve CXDH/CDH variant LF / LR as the first element after HSIF interface. OHER VRINS ES Manual emergency Rotary emergency R5 Rotary emergency 80 max 66 max 6.5 Ø.5.5 7 Ø 0 8.5 8.5 8.5 98.5 0 7 J M Junior D M Junior + Diode CZ Deutsch D04- SL Flying leads 66.7 5.7 66.5 5.7 54. 54. 54. Emergency and 5, tightening torque max. 6 9 Nm (CH n. ) IE/CXDH-CDH-VR/0/0 7

CFS OS COMENSED FLOW SHRING VLVE HIGH EFFICIENCY ENERGY SVING High efficiency energy saving valve FLOW SHRING High effi ciency energy saving valve Compact dimensions Venting valves can be adopted to de-pilot pressure compensators on port and/or Valve s body with the same interface of all bankable valves range, so can be assembled with all existings valves, precompensated (CXDH) included Cast iron zinc plated body. Connector to be ordered separately, see page 05. ORDERING CODE FEURES CFS N FLOW SHRING valve Size Mounting (see table ) ody type: = orts G/8 parallel = orts G/ parallel Q = orts SE8 /4-6UNF parallel G= Interface for modular valves Spool type () 0 = Symmetrical fl ow path control Nominal flow rating p 4 bar from to, 8 l/min 6 l/min 5 l/min 4 40 l/min 5 (5) 55 l/min Max. current at solenoid (): E =.5 (9 Vdc) - Special coil F =.76 ( Vdc) G = 0.88 (4 Vdc) Variants (): S = No variant LF/LV = Emergency control lever (4) For body type G order LR variant (emergency lever 80 rotated) SV = Viton ES = Emergency button (4) = Rotary emergency (4) R5 = Rotary emergency 80 (4) J = M Junior coil (see page ) CZ = Deutsch D04- coil (see page ) Serial No. Max. operating pressure 0 bar Max. operating pressure ports (ressure dynamic allowed for millions of cycles) 50 bar Regulated fl ow rate ( / ports) (6) up to 55 l/min ( p 4 bar) up a 60 l/min ( p 8 bar) Relative duty cycle Continuous 00% ED ype of protection (Hirschmann coil) I 65 Fluid viscosity 0 500 mm²/s Fluid temperature -0 C 75 C mbient temperature -0 C 60 C Max. contamination level (fi lter ß0 75) ISO 4406:999: class 9/7/4 NS 68: class 8 Weight with single solenoid Weight with double solenoid.70 kg 4.0 kg Solenoid @ 9Vdc @ Vdc @ 4Vdc Current supply WM (pulse width modulation) Max. current solenoid.5.76 0.88 Solenoid coil resistance at 5 C (77 F).5 Ohm 4.0 Ohm 6.0 Ohm WM or superimposed dither frequency 00 50 Hz Response time 0 00% 00% 0 ms ms 40 ms ms 85 ms ms Frequency response -db (input signal 50% ±5% Vmax) Hz Hz Hz Operating specifications are valid for fluid with 46 mm²/s viscosity at 40 C, using the specified Dana revini electronic control units. (input voltage = 4V). ccessories REM.S.R... REM.D.R... Card type control for single and double solenoid CE.S... Electronic amplifi er plug version for signle solenoid MV Electronic module for integrate control of proportional valves and ON/OFF JMEI0M7000 Joystick with standard handle JMIU0M7008 Joystick erson present handle Modular valves CM (page 95) and CMM (page 97) Calibrated diaphragms on line, see page 04. () vailable spool 0 and ports are not sealed. () Coils technical data, see page Voltage codes are not stamped on the plate, their are readable on the coils () Connector to be ordered separately, see page 05; Other variants available on request. (4) Emergency see page77 (5) Only for emergency lever (6) With FH5Q you can set a p variable (from LS and ); with FEH0Q the p is fixed at bar ab. - Mounting Code C a O b a O O b Symbol IE/CFS00/0-07 74

CFS HYDRULIC SYMOLS Spool 0 mounting C-- CFSC.0.. CFS.0.. CFS.0.. Spool 0 mounting C-- CFSC.0.. CFS.0.. CFS.0.. CHRCERISIC CURVES Q-I curves with p 4bar Compensation curves 60 60 5 5 50 50 Q (l/min) 40 0 0 0 4 Q (l/min) 40 0 0 0 4 Flow 8 l/min Curves 6 l/min 5 l/min 4 40 l/min 5 55 l/min 0 0 0 0 0 40 50 60 70 80 90 00 I(%) 0 0 50 00 50 00 50 00 p (bar) IE/CFS00/0-07 75

CFS OVERLL DIMENSIONS 59 O-RING 08/-008 90Sh ody = orts G/8 parallel = orts G/ parallel Q = orts SE8 /4-6UNF parallel 70,5 0, N 4 49 = G/8 L= 0,5 = G/ L=8,00 Q = SE8 /4-6UNF L=8,00,8 0, 69,5 5 9 x Ø 4,5 6 8,8 4 8 7,5 9,5 80 6,5 89,5 80 49,5 O-RING 07/-0 90Sh L 46 ody type G Interface for modular valves Fittings, max. tightening torque 60 Nm 4x M5 x Ø 5,5 IE/CFS00/0-07 76

CFS (variants) LF, LR ND LV VRINS - EMERGENCY CONROL LEVER HYDRULIC SYMOL Var. LF/LR lever on the side : hanks to his flexibility, the component is designed to be inserted between the valve body and the spool, providing total interchangeability between the different types of solenoid body valves manufactured by Dana revini (). he control can be used as an emergency device in the event of power cuts. Var. LV lever on the side : Max operating pressure port dynamic 60 bar static 0 bar Mounting type Var. LF/LR Mounting type Var. LV C - C - Spools type 0-0 Max flow of proportional valves can be reduced compared to versions without emergency control lever when electrical operated. Max flow of proportional valves lever operated is increased compared to the max flow given when valves are electrical operated. LF Variant 8 LV Variant 8 8 8 65,6 6 0, 6 6,5 0,5 89,5 80 0,5 LR Variant 7.5 8 8 OHER VRINS ES Manual emergency Rotary emergency R5 Rotary emergency 80 J M Junior D M Junior + Diode CZ Deutsch D04- max 66 max 6 8.5.5 Ø 8.5.5 8.5.5 7 Ø 0 66.7 5.7 66.5 98.5 0 7 54. 54. Emergency and 5, tightening torque max. 6 9 Nm (CH n. ) IE/CFS-VR/0-05 77

FIHL INERMEDIE ELEMEN FOR RE ND OS COMENSED VLVES Intermediate element FIHL with pass through - and LS lines. Suggested in assemblies with more than 8 elements in order to give better support and stability. Maximum fl ow 80 l/min. Cast iron zinc plated body or aluminum (L variant). HYDRULIC SYMOLS LS ORDERING CODE FEURES FIH L Intermediate element Size With LS line 00 = No variant (cast iron body) L = luminum body V = Viton Serial No. Max. operating pressure 00 bar (cast iron) 50 bar (aluminum) Max. Flow 80 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm²/s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight.6 kg (cast iron) 0.59 kg (aluminum) Mounting kit (screws and tie rods)contact our customer service. OVERLL DIMENSIONS 54 N M6 8 46 Space for nameplate 70 59 Ø 6,5 0 0 M6 Ø 6,5 ORING -00 90Sh ORINGS -0 90Sh 9 4 4,5 89 49 46 IE/FIHL/00-08 78

FUH OULE MODULE UNIS Outlet module units FUH hreaded ports () sizes G/4 Only for parallel connections Maximum flow 80 l/min. Cast iron zinc plated body. HYDRULIC SYMOL LS ORDERING CODE FEURES FUH 5 00 Outlet module unit Size ort size: 5 = G/4 00 = No variants Serial No. Max. operating pressure Max. Flow 00 bar 80 l/min Hydraulic fluids Mineral oils DIN 554 Fluid viscosity Fluid temperature 0 500 mm²/s -5 75 C mbient temperature -5 C 60 C Max. contamination level (filter ß5 75) Weight ISO 4406:999: class /9/6 NS 68: class 0. kg OVERLL DIMENSIONS 7 4 x Ø 6.5 90 0 x M6-6H 54 = = 59 = = 6 4 G/4" CH(HEX) 50 9 G /4" Ø x M6-6H lug with gasket (optional) to close port Code: Q66000 49 = = 70 = = IE/FUH00/0/08 79

80

SIZE 0 ON/OFF VLVES 8

ON/OFF VLVES Introduction Compact bankable valves with flow rates up to 80 l / min; High efficiency coils; vailable ON/OFF directional control bankable valve; vailable for parallel circuits; ssemblable with SIZE 6 valves. Overall dimensions with CD5 valves x M6-6H x M6-6H fixing holes mounting without fixing feet 7 Ch./Hex. 0 97.5 78 90.5 46 0 D C No. elements C mm FE5 Inlet module D mm C mm FE05 D mm 0 89 09 47 5 67 55 4 9 8 0 5 9 7 59 47 6 85 7 405 9 8

Composition form 7 5 6 4 5 6 8 Ref. ype Description age FE5 Inlet module units no pressure relief valve 84 FE05 Inlet module units with pressure relief valve 85 CD5 Directional control bankable valve 87 4 FU5 Outlet module units 90 5 Mounting kit 0 6 Fixing feet 0 7 Connectors 05 8 Coils 0 SIZE 0 valves CD5 can be assembled with: - valves CDC, CD, CX (page 6); - valves CXDH, CDH, CFS (page 56); o obtain the best performances, we suggest to assemble the working sections with higher flow rate near the inlet module, leaving the ones with lower flow at the end of the assembled valve. How to order o order the assembly, specify the codes in progressive order (inlet, valves, outlet, mounting kit, feet). See example page 6. For any further special version not shown in this catalogue, please contact our echnical Department. IE/NK-SIZE0/00-07 8

FE5 INLE MODULE UNIS NO RESSURE RELIEF VLVE Module units FE5 no pressure relief valve. hreaded ports ( and ), G/ Maximum fl ow 80 l/min Cast iron zinc plated body. FEURES HYDRULIC SYMOL Max. operating pressure 0 bar Max. Flow 80 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm²/s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.94 kg ORDERING CODE OVERLL DIMENSIONS FE Inlet module unit no pressure relief valve 5 Size ort sizes: = G/ 6 8 54 N M6 5 5 0 5 70 0.5 49 N M6 9 Ø4 Ø9 x OR -0 90Sh 0 00 = No variant V = Viton Serial No. 70 IE/FE500/00-07 84

FE05 INLE MODULE UNIS WIH RESSURE RELIEF VLVE Module units FE05 with CM0 adjustable pressure relief valve. Manual adjustment with a grub screw or plastic knob. hreaded ports - sizes G/ Maximum fl ow 80 l/min. Cast iron zinc plated body. FEURES HYDRULIC SYMOL M Max. operating pressure 0 bar Max. Flow 80 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight.85 kg ressure relief valve (CM0...) Setting range (): Spring Spring Spring max 50 bar max 40 bar max 50 bar () he minimum permissible setting pressure depending on the spring: see curves. ORDERING CODE RESSURE-FLOW RE MIN.SEING RESSURE FE0 5 Inlet module unit (up to 80 l/min) with pressure relief valve Size ort sizes: = G/ djustment: M = lastic knob C = Grub screw Setting ranges = max. 50 bar (white spring) = max. 40 bar (yellow spring) = max. 50 bar (green spring) 00 = No variant V = Viton Serial No. [bar] 400 50 00 50 00 50 00 50 ressure Flow 0 0 0 0 0 40 50 60 70 80 90 00 Q [l/min] 0 0 0 0 0 40 50 60 70 80 90 00 Q [l/min] = max 50 - bar - = max 40 bar - = max 50 bar Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C. [bar] 0 8 6 4 0 8 6 4 Minimun setting pressure -- IE/FE0500/00-07 85

FE05 OVERLL DIMENSIONS 6.5 5 60 5 7 7 47 50 0 85 5 50 5 M6 C 0.5 49 M6 6 5 70 Ø 4 N OR -0 90Sh M OR G/4" (LUGGED) M C = Grub screw M = lastic knob IE/FE0500/00-07 86

CD5 DIRECIONL CONROL NKLE VLVE Directional control bankable valve CD5 with single or double solenoid. Centring achieved by means of calibrated length springs which immediately reposition the spool in the neutral position when the electrical signal is shut off. Emergency control. hreaded ports sizes G/ Coils protection I66 Standard connectors DIN 4650 ISO 4400 and Deutsch Maximum fl ow until 80 l/min. Cast iron zinc plated body. ORDERING CODE FEURES CD 5 Directional control bankable valve Size N E ody parallel, ports G/ Electrical operator Spool (tab.) Mounting (tab.) Voltage (tab.4) Variants (tab.5) Serial No. Max. pressure ports /// 0 bar Max. pressure port 50 bar Max. Flow 80 l/min Max excitation frequency Hz Duty cycle 00% ED Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight with one solenoid Weight with two solenoids.68 kg.07 kg IE/CD500/00-07 87

CD5 ORDERING CODE ab. - Standard spools wo solenoids,spring centred C Mounting Code Covering ransient position 0 + 0 + ab. - Mounting Code Symbol C E F One solenoid, side E Mounting Code Covering ransient position 0 + 0 + ab. - 40W coils D5 voltage () Code Voltage Max. winding temperature (mbient temperature 5 C) Rated power W Resistance @ 0 C (Ohm) ±0% L Vdc 5 C 40.6 M 4 Vdc 5 C 40 4.4 W () Without coils One solenoid, side F Mounting Code Covering ransient position 0 + 0 + ab.4 - Variants ( - 4) Code Variant S No variant SV Viton ES Emergency button (see page 89) () Rotary emergency button (see page 89) R5 () Rotary emergency b. 80 (see page 89) CZ Deutsch D04- - 40W connection (see page 0) () Connector to be ordered separately, see page 05 Coils technical data, see page 0 Voltage codes are not stamped on the plate, their are readable on the coils () erformance are guaranteed only using valves completed with coil () ightening torque max. 6 9 Nm (CH n. ) (4) Other variants available on request RESSURE DROS LIMIS OF USE 4 50 00 (bar) 0 8 6 = >, =, > (bar) 50 00 50 = Spool 0 = Spool 0 4 00 50 0 0 0 0 0 40 50 60 70 80 Q (l/min) 0 0 0 0 0 40 50 60 70 80 Q (l/min) he diagram at the side shows the pressure drop curves for spools during normal usage. he fluid used is a mineral oil with a viscosity of 46 mm²/s at 40 C ; the tests have been carried out at a fluid temperature of 40 C. he tests have been carried out with solenoids at operating temperature and a voltage 0% less than rated voltage with a fluid temperature of 50 C. he fluid used was a mineral oil with a viscosity of 46 mm²/s at 40 degrees C. Spool 0: in neutral position can have leaks. IE/CD500/00-07 88

CD5 OVERLL DIMENSIONS N ORINGS -0 NR 90Sh.5 45.5 4 78 49 n 4 Ø 6.5 59 N G/" N Ø 8 Fittings, max. tightening torque 60 Nm 46 Manual emergency 5 80 95.5 80 8.7 Single solenoid versions 55.5 VRINS ES Manual emergency Rotary emergency R5 Rotary emergency 80 CZ Deutsch D04- R6 Deutsch D04- ecoat treatment max 66 max 6 8.5 8.5 8.5 66.5.5 98.5 Ø.5 0.5 7 7 Ø 0 54. Emergency and 5, tightening torque max. 6 9 Nm (CH n. ) IE/CD500/00-07 89

FU5 OULE MODULE UNIS Outlet module units FU5. hreaded ports () sizes G/8. Maximum flow 80 l/min. Cast iron zinc plated body. FEURES Max. operating pressure 0 bar Max. Flow 80 l/min Hydraulic fluid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (filter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.95 kg HYDRULIC SYMOLS OVERLL DIMENSIONS N M6 8 54 FU 59 N 6 Ø 6. 5 5 5 70 4 00 8 4. 5 49 G/4" 0 5 ORDERING CODE Outlet module unit Size ort size: 5 = G/4 00 = No variants Serial No. 70 IE/FU500/00-07 90

MODULR ELEMENS (pplicability with SIZE 6 valves, see pages 8, 58) 9

V08000005 INERMEDIE ELEMEN WIH FLOW REGULOR ON ND LINES Intermediate element V08000005 with fl ow regulator on and lines Intermediate mounting to combine with valves CMF/CM/CMM One way non-compensated throttle valves adjustable by means of a grub screw on and lines. Maximum fl ow 0 l/min. Cast iron zinc plated body. FEURES HYDRULIC SYMOL Max. operating pressure 50 bar Flow rate regulation on 6 screw turns Max. Flow 0 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight. kg ORDERING CODE OVERLL DIMENSIONS V08000005 Element with fl ow regulator on and lines 5 70 FLOW REGULION n of turns unscrewing ~ 9 5.5.5 4 40 (bar) 0 00 4.5 80 60 40 0 5 00 80 60 5.5 6 40 0 0 0 4 6 8 0 4 6 8 0 Q (l/min) 6 9 n. 4 Ø 5 7,6 45 IE/V08000005/0-05 9

V0800000 INERMEDIE ELEMEN WIH ILO OERED CHECK SCKLE VLVES Modular pilot operated check stackable valves V0800000 Intermediate mounting to combine with valves CMF/CMM Double and lines; Cast iron zinc plated body. FEURES HYDRULIC SYMOL Max. operating pressure 50 bar Minimum opening pressure 5 bar Max. Flow 0 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm /s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.69 kg ORDERING CODE OVERLL DIMENSIONS V0800000 ilot operated check stackable valve 8 FLOW REGULION 6 74 5 0 5 8 (bar) 0 6 45 5 9 n. 4 Ø 5.5 0 0 4 6 8 0 4 6 8 0 Q (l/min) = piloted side flow = minimum opening pressure IE/V0800000/00-07 9

CMF MODULR ELEMENS WIH ORS - Modular elements CMF with ports -. Convert modular interface into threaded ports. Maximum fl ow 40 l/min. hreaded ports sizes G/8 Cast iron zinc plated body. FEURES HYDRULIC SYMOL Max. operating pressure 50 bar Max. Flow 40 l/min Hydraulic fl uid DIN 554 Mineral oils Fluid viscosity 0 500 mm²/s Fluid temperature -5 C 75 C mbient temperature -5 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight 0.54 kg ccessories Elements Code screws (x 4) ype UNI 59-8.8 CMF Q6074069 M5x5 ightening torque 5 Nm CMF + V0800005 Q6074077 M5x80 ORDERING CODE OVERLL DIMENSIONS CM Intermediate element Size 7 F x O-RING -0 90Sh G/8" 45 6 With ports - 00 = No variant V = Viton Serial No. 0,5 70 IE/CMF00/0-05 94

CM MODULR ILO OERED CHECK NKLE VLVES CM type modular check bankable valves allow one way free fl ow by raising a conical shutter, while in the opposite direction the fl uid can return by means of a small piston piloted by the pressure in the other line. vailable on single or lines, and on double and lines (see hydraulic symbols). hreaded ports G/8 or 9/6-8UNF. Cast iron zinc plated body. ORDERING CODE FEURES CM Modular bankable valve Size iloted check valve ort sizes: = G/8 = 9/6-8UNF Control on lines / / Minimum opening pressure = bar 5 = 5 bar Max. operating pressure 50 bar Minimum opening pressure spring bar Minimum opening pressure spring 5 5 bar iloting ratio :4 Max. fl ow 40 l/min Hydraulic fl uids Mineral oils DIN 554 Fluid viscosity 0 500 mm²/s Fluid temperature -0 C 75 C mbient temperature -0 C 60 C Max. contamination level (fi lter ß5 75) ISO 4406:999: class /9/6 NS 68: class 0 Weight.5 kg ccessories Elements Code screws (x 4) ype UNI 59-8.8 00 = No variant V = Viton Serial No. ightening torque 5 Nm CM Q607407 M5x50 CM + V0800005 Q60745 M5x95 HYDRULIC SYMOLS CM CM CM IE/CM00/0/0 95