DEMOLITION ND SORTING GRBS D-SERIES
HPXdrive Vast lifespan extension compared to conventional cylinder grabs as extremely low cost of ownership vailable for excavators with 2t up to 9t operating weight No protruding components Easy shell exchange - different shells available Low maintenance Compact unit No greasing points High constant closing force The hydraulic drive unit HPXdrive, characterized by its constant closing force, is optimally suited for daily operations in general construction or demolition and sorting tasks. In contrast to conventional hydraulic grabs, with the HPXdrive the torque is generated by two hollow shafts, which run opposed and have a helix thread, hydraulically driven by a single piston. The force is delivered to two shafts, on which the shells are mounted. These advantages of the HPXdrive - technology provide an extended service life and higher efficiency.
Comparison of Closing Forces in kn Compact Design 24 kn D05HPX conventional cylinder grab C08HPX 12 kn conventional grab 0 kn open center closed Position of shell s cutting edges WRRNTY GRNTIE YERS JHRE NS JR GRNTIE WRRNTY
1 t 2 t 3 t 4 t 5 t 6 t... 9 t 10 t 11 t... 17 t 18 t... 21 t 22 t 23 t 24 t 25 t 26 t D02H Demolition and sorting grab for excavators with 1t / 2200 lbs to 2t / 4400 lbs operating weight the universal tool for lighter demolition and sorting tasks of all kinds. Demolition and Sorting Grab l Perforated skin of shells lets dust and gravel through. l Extremely robust due to the use of cutting edge material 500 HB steel. l Cutting edges usable both sides. l Integrated non-return valve guarantees secure retention of loads. l Precise positioning through mounted rotator with endless rotation. l High closing force achieved by horizontal cylinder (20 kn / 4400 lbf at 200 bar / 2880 psi Operating pressure). Demolition and Sorting Grab D02H Width Opening Height Volume Self weight Closing force E C max. (mm/in) (mm/in) (mm/in) (litre/c.y.) (kg/lbs) (kn/lbf) D02H 300 / 11.81 790 / 31.10 770 / 30.31 35 / 0.05 115 / 253 20 / 4400 Package consists of: demolition and sorting grab, KINSHOFER rotator, non-return valve, cutting edges KINSHOFER Rotator Continuous rotation and two oil passages. Overload protection is ensured by pressure relief valves. Upper connection Torque Moment of deflection (bores/ø-hole pattern) max. (mm/in) (Nm/ft.lbs) (Nm/ft.lbs) KM 04 F140/150 10 x M 12 / Ø 150/5.91 850 / 630 3000 / 2215 ccessories KM 691 2t KM 690 2t KSW01 rigid adapter connection plate for specific solutions up to 2t / 4400 lbs adapter for rigid mounting up to 2t / 4400 lbs bolt-on-adapter for System L-Lock KMS01/KHS01 for rigid mounting up to 2t / 4400 lbs adapters for quick change systems from other manufacturers or different sizes available on request Operating pressure (open/close): Recommended oil flow (open/close): Operating pressure (rotation): Recommended oil flow (rotation): max. 20 MPa (200 bar) / 2880 psi 10 - max. 40 l/min / 2.64 - max. 10.57 GPM max. 32 MPa (320 bar) / 4608 psi 15 - max. 50 l/min / 3.96 - max. 13.21 GPM Cmax E
1 t 2 t 3 t 4 t 5 t 6 t 7 t 8 t... 19 t 20 t 21 t 22 t 23 t 24 t 25 t 26 t 27 t 28 t 29 t Demolition and Sorting Grabs with HPXdrive NEW D04HPX / D06HPX The new demolition and sorting grabs with the low maintenance HPXdrive for excavators up to 4t / 8800 lbs or 6t / 13200 lbs operating weight THE universal tool for all kind of light demolition and sorting work. l HPXdrive the revolutionary concept for hydraulically operated grabs! The rotation of the arms of the grab is generated by two hollow shafts, which run opposed and have a helix thread, hydraulically driven by a single piston. No hydraulic cylinder required! Integrated non-return valve guarantees secure retention of the loads! l 50% longer life cycle. The drive unit runs in a permanent oil bath no lubrication necessary. Resistant against dirt and blows, due to the compact design. l Including the new, flat 10t-rotator with 360 endless rotation for precise positioning. l Constant closing forces during the entire operation. l Different applications possible through easy exchange system. l New improved shell design! The perforated skin of the shells lets dust and fine gravel through without larger pieces blocking the shell filter system. l Robust due to the use of cutting edge material 500 HB steel. Cutting edges usable both sides. l Optional: adapter with compression rails to handle e.g. curbstones without damaging them. D06HPX Demolition and Sorting Grabs D04HPX / D06HPX Load Load Width Opening Height Volume Weight capacity* capacity* Closing Operating C max. (form locking) (friction locking) force** weight (mm/in) (mm/in) (mm/in) (litre/c.y.) (kg/lbs) (kg/lbs) (kg/lbs) (kn/lbf) (t/lbs) D04HPX-40 420 / 16.54 1045 / 41.14 812 / 31.97 75/ 0.10 280 / 616 1500 / 3300 1000 / 2200 18 / 3960 2-4 / 4400-8800 D06HPX-45 470 / 18.50 1350 / 53.15 970 / 38.19 150 / 0.20 340 / 748 2000 / 4400 1000 / 2200 18 / 3960 4-6 / 8800-13200 *) the load capacity indicated depends on the characteristics of the load (surface, largeness etc.) **) D04: at 25MPa / 3600 psi - D06: at 26MPa / 3744 psi Package consists of: demolition and sorting grab, KINSHOFER rotator, non-return valve, cutting edges KINSHOFER Rotator Integrated in a single unit with the HPXdrive, no more connecting hoses. Continous rotation. Overload protection ensured by pressure relief valves. Upper connection Torque Moment of deflection max. (bores/ø-hole pattern) (mm/in) (Nm/ft.lbs) (Nm/ft.lbs) KM 10 F214/180 6 x M 16 / Ø 180/7.09 1000 / 738 12000 / 8850 ccessories KM 691 8t adapter connection plate for specific solutions up to 8t / 17600 lbs KM 690 8t adapter for rigid mounting up to 8t / 17600 lbs KSW03 rigid bolt-on-adapter for System L-Lock KMS03/KHS03 for rigid mounting up to 6t / 13200 lbs adapters for quick change systems from other manufacturers or different sizes available on request KM 980-2 2t-8t solenoid valve for additional oil circuit, up to 26 MPa / 37.44 psi, ready for mounting for self installation without parts KM 980-2 2t-8t c solenoid valve for additional oil circuit, up to 26 MPa / 37.44 psi, incl. assembly parts and mounting D04HPX-40S exchangeable shells for D04HPX-40 incl. exchange aid D06HPX-45S exchangeable shells for D06HPX-45 incl. exchange aid KM 685 05-D04-D09 Plug-in device with pressure rails for D04 to D09 (load capacity with compression rails: 750 kg / 1650 lbs ) D04HPX D06HPX Operating pressure (open/close): max. 25 MPa (190 bar) / 3600 psi max. 32 MPa (320 bar) / 4608 psi internal 26 MPa (260 bar) / 3744 psi Recommended oil flow (open/close): 40 - max. 75 l/min / 10.57 - max. 19.82 GPM 40 - max. 75 l/min / 10.57 - max. 19.82 GPM Operating pressure (rotation): max. 32 MPa (320 bar) / 4608 psi max. 32 MPa (320 bar) / 4608 psi Recommended oil flow (rotation): 15 - max. 50 l/min 20 - max. 50 l/min / 5.28 - max. 13.21 GPM Cmax Cmax D04HPX D06HPX
1 t 2 t 3 t 4 t 5 t 6 t 7 t 8 t 9 t 10 t 11 t 12 t 13 t... 33 t 34 t 35 t 36 t 37 t 38 t D09HPX NEW Demolition and sorting grab with the low maintenance HPXdrive for excavators up to 9t / 19800 lbs operating weight the universal tool for all kind of light demolition and sorting work. Demolition and Sorting Grab with HPXdrive l HPXdrive the revolutionary concept for hydraulically operated grabs! The rotation of the arms of the grab is generated by two hollow shafts, which run opposed and have a helix thread, hydraulically driven by a single piston. No hydraulic cylinder required! Integrated non-return valve guarantees secure retention of the loads! l 50% longer life cycle. The drive unit runs in a permanent oil bath no lubrication necessary. Resistant against dirt and blows, due to the compact design. l Including the flat 15t-rotator with 360 endless rotation for precise positioning. l Constant closing forces during the entire operation. l Different applications possible through easy exchange system. l New improved shell design! The perforated skin of the shells lets fine dust and gravel through without larger pieces blocking the shell filter system. l Cutting edges usable both sides - robust due to the use of cutting edge material 500 HB steel. l Optional: adapter with compression rails to handle e.g. curbstones without damaging them. Demolition and Sorting Grab D09HPX Load Load Width Opening Height Volume Weight capacity* capacity* Closing E C max. (form locking) (friction locking) force** (mm/in) (mm/in) (mm/in) (litre/c.y.) (kg/lbs) (kg/lbs) (kg/lbs) (kn/lbf) D09HPX-50 520 / 20.47 1545 / 60.83 1061 / 41.77 220 / 0.29 415 / 913 2500 / 5500 1000 / 2200 15,3 / 3366 *) the load capacity indicated depends on the characteristics of the load (surface, largeness etc.) **) at 26 MPa / 3744 psi Package consists of: demolition and sorting grab, KINSHOFER rotator, non-return valve, cutting edges KINSHOFER Rotator Continuous rotation and two oil passages. Overload protection is ensured by pressure relief valves. Upper connection Torque Moment of deflection max. (bores/ø-hole pattern) (mm/in) (Nm/ft.lbs) (Nm/ft.lbs) KM 15 F273/273 10 x M16 / Ø 273/10.75 2000 / 1475 50000 / 36875 ccessories KM 691 8t KM 690 8t OQ45 KSW08 rigid KM 980-2 2-8t KM 980-2 2-8t c D09HPX-50S KM 685 05-D04-D09 adapter connection plate for specific solutions up to 8t / 17600 lbs adapter for rigid mounting up to 8t / 17600 lbs bolt-on-adapter for Oilquick OQ45 5t to 12t / 11000 lbs to 26400 lbs bolt-on-adapter for System L-Lock KMS08/KHS08 for rigid mounting up to 12t / 26400 lbs adapters for quick change systems from other manufacturers or different sizes available on request solenoid valve for additional oil circuit, up to 26 MPa / 37.44 psi, ready for mounting for self installation without parts solenoid valve for additional oil circuit, up to 26 MPa / 37.44 psi, incl. assembly parts and mounting exchangeable shells for D09HPX-50 incl. exchange aid Plug-in device with pressure rails for D04 to D09 (load capacity with compression rails: 750 kg) Operating pressure (Open/Close): Recommended oil flow (Open/Close): Operating pressure (Rotation): Recommended oil flow (Rotation): max. 32 MPa (320 bar) / 4608 psi and internal 26 MPa (260 bar) / 3744 psi 40 - max. 75 l/min / 10.57 - max. 19.82 GPM max. 35 MPa (350 bar) / 5040 psi 20 - max. 50 l/min / 5.28 - max. 13.21 GPM Cmax E
1 t 2 t 3 t 4 t 5 t 6 t... 9 t 10 t 11 t... 17 t 18 t... 21 t 22 t 23 t 24 t 25 t 26 t Demolition and Sorting Grabs The new demolition and sorting grabs for excavators with 2t / 4400 lbs to 4t / 8800 lbs or 3t / 6600 lbs to 6t / 13200 lbs operating weight THE universal tool for lighter demolition and sorting tasks of all kinds. NEW D04H / D06H l New improved shell design! l Including the new, flat 10t-rotator with 360 endless rotation for precise positioning. l Perforated skin of shells lets dust and gravel through. l Extremely robust due to the use of cutting edge material 500 HB steel. l Cutting edges usable both sides. l Integrated non-return valve guarantees secure retention of loads. l High closing force achieved by horizontal cylinder l Optional: matching accessories like adapter with compression rails to handle e.g. curbstones without damaging them. D04H Demolition and Sorting Grab D04H / D06H Width Opening Height C Volume Load Load Weight Closing Operating max. capacity* capacity* force** weight (form locking) (friction locking) (mm/in) (mm/in) (mm/in) (litre/c.y.) (kg/lbs) (kg/lbs) (kg/lbs) (kn/lbf) (t/lbs) D04H-40 420 / 16.54 1212 / 47.72 747 / 29.41 60 / 0.08 1500 / 3300 1000 / 2200 200 / 440 21.5 / 4730 2-4 / 4400-8800 D06H-45 470 / 18.50 1345 / 52.95 817 / 32.17 90 / 0.12 2000 / 4400 1000 / 2200 227 / 499 21 / 4620 4-6 / 8800-13200 *) the load capacity indicated depends on the characteristics of the load (surface, largeness etc.) **) at 25 MPa / 3600 psi Package consists of: demolition and sorting grab, KINSHOFER rotator, non-return valve, cutting edges KINSHOFER Rotator Continuous rotation and two oil passages. Overload protection is ensured by pressure relief valves. Upper connection Torque Moment of deflection max. (bores/ø-hole pattern) (mm/in) (Nm/ft.lbs) (Nm/ft.lbs) KM 10 F214/180 6 x M 16 / Ø 180/7.09 1000 / 738 12000 / 8850 ccessories KM 691 8t KM 690 8t KSW03 rigid KM 685 05-D04-D09 adapter connection plate for specific solutions up to 8t / 17600 lbs adapter for rigid mounting up to 8t / 17600 lbs bolt-on-adapter for System L-Lock KMS03/KHS03 for rigid mounting up to 6t / 13200 lbs adapters for quick change systems from other manufacturers or different sizes available on request Plug-in device with pressure rails for D04 to D09 (load capacity with compression rails: 750 kg / 1650 lbs) D04H D06H Operating pressure (open/close): max. 25 MPa (250 bar) / 3600 psi max. 25 MPa (250 bar) / 3600 psi Recommended oil flow (open/close): 25-75 l/min / 6.61-19.82 GPM 25-75 l/min / 6.61-19.82 GPM Operating pressure (rotation): max. 32 MPa (320 bar) / 4608 psi max. 32 MPa (320 bar) / 4608 psi Recommended oil flow (rotation): 15 - max. 50 l/min / 3.96 - max. 13.21 GPM 15 - max. 50 l/min / 3.96 - max. 13.21 GPM C max. C max. D04H D06H
1 t 2 t 3 t 4 t 5 t 6 t 7 t 8 t 9 t 10 t 11 t 12 t 13 t... 33 t 34 t 35 t 36 t 37 t 38 t D09H NEW The new demolition and sorting grabs for excavators with 6t / 13200 lbs to 9t / 19800 lbs operating weight THE universal tool for lighter demolition and sorting tasks of all kinds. Demolition and Sorting Grab l New improved shell design! l Including the flat 15t-rotator with 360 endless rotation for precise positioning. l Perforated skin of shells lets dust and gravel through. l Extremely robust due to the use of cutting edge material 500 HB steel. l Cutting edges usable both sides. l Integrated non-return valve guarantees secure retention of loads. l High closing force achieved by horizontal cylinder l Optional: matching accessories like adapter with compression rails to handle e.g. curbstones without damaging them. Demolition and Sorting Grab D09H Load Load Width Opening Height C Volume capacity* capacity* Weight Closing max. (form locking) (friction locking) force** (mm/in) (mm/in) (mm/in) (litre/c.y.) (kg/lbs) (kg/lbs) (kg/lbs) (kn/lbf) D09H-50 520 / 20.47 1665 / 65.55 973 / 38.31 165 / 0.22 2500/ 5500 1500/ 3300 355 / 781 24 / 5280 *) the load capacity indicated depends on the characteristics of the load (surface, largeness etc.) **) at 25 MPa / 3600 psi Package consists of: demolition and sorting grab, KINSHOFER rotator, non-return valve, cutting edges KINSHOFER Rotator Continuous rotation and two oil passages. Overload protection is ensured by pressure relief valves. Upper connection Torque Moment of deflection max. (bores/ø-hole pattern) (mm/in) (Nm/ft.lbs) (Nm/ft.lbs) KM 15 F273/273 10 x M16 / Ø 273/10.75 2000 / 1475 50000 / 36875 ccessories KM 691 8t KM 690 8t KSW08 rigid KM 685 05-D04-D09 adapter connection plate for specific solutions up to 8t / 17600 lbs adapter for rigid mounting up to 8t / 17600 lbs bolt-on-adapter for System L-Lock KMS08/KHS08 for rigid mounting up to 12t / 26400 lbs adapters for quick change systems from other manufacturers or different sizes available on request Plug-in device with pressure rails for D04 to D09 (load capacity with compression rails: 1000 kg / 2200 lbs) Operating pressure (open/close): Recommended oil flow (open/close): Operating pressure (rotation): Recommended oil flow (rotation): max. 32 MPa (320 bar) / 4608 psi 25-75 l/min / 6.61-19.82 GPM max. 32 MPa (320 bar) / 4608 psi 20 - max. 50 l/min / 5.28 - max. 13.21 GPM Cmax E
1 t 2 t... 8 t 9 t... 25 t 26 t... 37 t 38 t 39 t 40 t 41 t... 55 t... 60 t... 65 t Demolition and Sorting Grabs Robust multi purpose grabs for excavators from 8t / 17600 lbs to 37t / 81400 lbs operating weight. Well-suited for demolition and seperation of all kinds of building materials and waste. D15H to D27H / D12H-P to D37H-P l Robust, fully integrated rotation with sturdy slewing ring to withstand external forces, with connecting hoses located inside the hub. Hydraulic quick change adapters are directly mountable to the head plate. Different bolt patterns are available. Integrated pressure relief valve to avoid peak-pressures in rotation motor(s). (D12: incl. rotator KM 15 F273/273) l Exceptional closing forces provided by two horizontal hydraulic cylinders which are well protected by the carrier. l The end position (grab open) is hydraulically cushioned to envoid damage to the cylinder when the grab is pushed into the material. l The grabs feature a perforated skins or metal ribs to let fine dust and debris through without larger pieces getting caught. The durable, replaceable and indexable wear blades (500HB) enable the grabs to pinch with their edges without excessive wear. D24H-P Demolition and Sorting Grabs with metal ribs D15H / D20H / D27H Width Opening Height Height Volume Weight Load Closing Torque Operating E C max. C min. capacity force weight (mm/in) (mm/in) (mm/in) (mm/in) (litre/c.y.) (kg/lbs) (kg/lbs) (kn/lbf) (Nm/ft.lbs) (t/lbs) D15H-80 800 / 1545 / 1215 / 1070 / 4000 / 3000 / 11-15 / 300 / 0.39 670 / 1474 27 / 5940 31.50 60.83 47.83 42.13 8800 2215 24200-33000 D20H-100 1000 / 1890 / 1405 / 1210 / 450 / 0.59 1150 / 2530 5000 / 43 / 9460 4000 / 14-20 / D27H-115 Operating pressure (open/close): D12 - D20: max. 32 Mpa (320 bar) / 4608 psi; D24 - D37: max. 35 Mpa (350 bar) / 5040 psi Recommended oil flow (open/close): D12 - D37: 75 - max. 150 l/min / 19.82 - max. 39.63 GPM Hydraulic connection (grab/rotate): D12 - D20: G 3/4 / G 1/2 ; D24 - D37: G 1 / G 1/2 Operating pressure (rotation): D12: max. 35 MPa (350 bar) / 5040 psi; D15 - D37: max. 14 MPa (140 bar) / 2016 psi Recommended oil flow (rotation): D12 - D37: 20 - max. 50 l/min / 5.28 - max. 13.21 GPM D24H-P with perforated shells 39.37 1150 / 45.28 74.41 2145 / 84.45 55.31 1575 / 62.00 47.63 1375 / 54.13 800 / 1.05 1700 / 3740 11000 6000 / 13200 63 / 13860 Package consists of: demolition and sorting grab, integrated rotation with sturdy slewing ring, wear blades and non-return valve 2950 5000 / 3690 30800-44000 20-27 / 44000-59400 Demolition and Sorting Grabs with perforated shells D12H-P / D15H-P / D20H-P / D24H-P / D27H-P / D37H-P Width Opening Height Height Volume Weight Load Closing Torque Operating E C max. C min. capacity force weight (mm/in) (mm/in) (mm/in) (mm/in) (litre/c.y.) (kg/lbs) (kg/lbs) (kn/lbf) (Nm/ft.lbs) (t/lbs) D12H-P-60 600 / 1550 / 1125 / 980 / 3000 / 3000 / 8-12 / 225 / 0.29 470 / 1034 36 / 7920 23.62 61.02 44.29 38.58 6600 2215 17600-26400 D15H-P-80 800 / 1550 / 1215 / 1070 / 4000 / 3000 / 11-15 / 300 / 0.39 630 / 1386 27 / 5940 31.50 61.02 47.83 42.13 8800 2215 24200-33000 D20H-P-100 1000 / 1890 / 1400 / 1205 / 5000 / 4000 / 14-20 / 450 / 0.59 1120 / 2464 43 / 9460 39.37 74.41 55.12 47.44 11000 2950 30800-44000 D24H-P-100 1000 / 2005 / 1470 / 1235 / 5000 / 5700 / 18-24 / 650 / 0.85 1175 / 2585 42 / 9240 39.37 78.94 57.87 48.62 11000 4204 39600-52800 D27H-P-115 1150 / 2145 / 1575 / 1410 / 800 / 1.05 1600 / 3520 6000 / 63 / 13860 5000 / 20-27 / 45.28 84.45 62.00 55.51 13200 3690 1250 / 2260 / 1620 / 1480 / 8000 / 7000 / D37H-P-125 950 / 1.24 2100 / 4620 86 / 18920 49.21 88.98 63.78 58.27 17600 5162 Package consists of: demolition and sorting grab, integrated rotation with sturdy slewing ring (D12H-P: rotator KM 15 F273/273), wear blades and non-return valve ccessories KM 690 OQ KSW21/25 rigid adapter for rigid mounting bolt-on adapter for Oilquick OQ 5t to 70t / 11000 lbs to 154000 lbs bolt-on-adapter for System L-Lock KMS21/25 / KHS21/25 for rigid mounting up to 40t / 88000 lbs adapter for quick change systems - from other manufacturers or different sizes available on request 44000-59400 27-37 / 59400-81400 D12H-P with perforated shells
10 t 11 t 12 t 13 t 14 t 15 t 16 t 17 t 18 t 19 t 20 t 21 t 22 t... 33 t 34 t 35 t 36 t 37 t 38 t D20H-P to D37-P Robust multi purpose grabs with integrated quick change adapter for excavators from 14t / 30800 lbs to 37t / 81400 lbs operating weight. Well-suited for the demolition and seperation of all kinds of building materials and waste. Demolition & Sorting Grabs with integrated dapter l Robust, fully integrated rotation with sturdy slewing ring to withstand external forces, with connecting hoses located inside the hub. Integrated pressure relief valve to avoid peak-pressures in the rotation. l Quick change adapter integrated into the head piece and thus lower overall height. l Exceptional closing forces provided by two horizontal hydraulic cylinders which are well protected by the carrier. l The end position (grab open) is hydraulically cushioned to avoid damage to the cylinder when the grab is pushed into the material. l The shells have a perforated skin that lets fine dust and debris through without larger pieces getting caught. The durable, replaceable and turneable wear blades (500HB) enable the grabs to pinch with their edges without excessive wear. D20H-P-KMS10 Selector Grabs with perforated shells and integrated quick change adapter D20H-P-KMS10 / D27H-P-OQ70/55 / D37H-P-OQ80 Width Opening Height Height Volume Weight Load Closing Operating E C max. C min. capacity force weight (mm/in) (mm/in) (mm/in) (mm/in) (litre/c.y.) (kg/lbs) (kg/lbs) (kn/lbf) (t/lbs) D20H-P-KMS10 1000 / 39.37 1890 / 1120 / 5000 / 14-20 / 1570 / 61.81 1290 / 50.79 450 / 0.59 43 / 9460 74.41 2464 11000 30800-44000 D27H-P-OQ70/55 1150 / 45.28 2140 / 6000 / 20-27 / 1700 / 66.29 1500 / 59.06 800 / 1.05 1500 / 3300 63 / 13860 85.25 13200 44000-59400 D37H-P-OQ80 1250 / 49.21 2260 / 8000 / 27-37 / 1750 / 68.90 1610 / 63.39 950 / 1.24 2100 / 4620 86/ 18920 88.98 17600 59400-81400 Package consists of: demolition and sorting grab, integrated rotation with sturdy slewing ring, quick change adapter, wear blades and non-return valve Operating pressure (open/close): D20: max. 32 Mpa (320 bar) / 4608 psi; D27 / D37: max. 35 Mpa (350 bar) / 5040 psi Recommended oil flow (open/close): D20 - D37: 75 - max. 150 l/min / 19.82 - max. 39.63 GPM Operating pressure (rotation): D20: max. 17 MPa (170 bar) / 5076 psi; D27/ D37: max. 14 MPa (140 bar) / 2016 psi Recommended oil flow (rotation): D20: max. 60l/min; D27/D37: max. 50l/min / 5.28 - max. 13.21 GPM D20H-P-KMS10 D37H-P-OQ80 C max. C min. C min. C max. E E
1 t 2 t... 10 t 11 t... 25 t 26 t... 38 t 39 t... 50 t 51 t... 65 t... 79 t 80 t 81 t Heavy Duty Demolition & Sorting Grabs D15H-P HD to D70H-P HD Robust multi-purpose grab with perforated shells, for excavators from 10t / 22000 lbs up to 80t / 176000 lbs operating weight, the HD D Series grabs are ideal for demolition and sorting of all kinds of building materials. l Robust Delta-box frame with dust-proof axle bearing points. l Perforated shells let fine dust and gravel through without large pieces getting caught. l Durable and reversable cutting edges, made of Cracox Plus 450 steel can be used to pick up different materials, with their tips. l Cutting edges on D19 series and higher can be turned three ways, reducing replacement costs. l Robust, fully integrated rotator with sturdy slewing ring to withstand external forces, with pressure relief valve to ensure overload protection, and connecting hoses protected inside the hub. l Exceptional closing forces achieved with a horizontally positioned hydraulic cylinder that is protected by the bucket carrier. l Cylinder is hydraulically cushioned. D32H-P-HD Heavy Duty Demolition and Sorting Grabs with perforated shells D15H-P-75HD to D70H-P150HD Width E Opening Height C Volume Weight Load Closing force Torque Operating weight (mm/in) (mm/in) (mm/in) (litre/c.y.) (kg/lbs) (kg/lbs) (kn/ibf) (Nm/ft.lbs) (t/lbs) D15H-P-75HD 750 / 29.53 1730 / 68.11 1295 / 50.98 340 / 0.44 860 / 1892 5000 / 11000 43 / 9460 3000 / 2215 10 18 / 22000-39600 D16H-P-90HD 900 / 35.43 1730 / 68.11 1295 / 50.98 415 / 0.54 900 / 1980 5500 / 121000 43 / 9460 3000 / 2215 12 20 / 26400-44000 D19H-P-85HD 850 / 1755 / 1320 / 365 / 1030 / 6500 / 33.46 69.09 51.97 0.48 2266 14300 50 / 11000 3000/5700 / 12 24 / 2215/4205* 26400-52800 D20H-P-100HD 1000 / 39.37 1895 / 74.61 1400 / 55.12 460 / 0.60 1120 / 2464 7000 / 15400 50 / 11000 3000/5700 / 2215/4205* 13 25 / 28600-55000 D24H-P-100HD 1000 / 39.37 1990 / 78.35 1455 / 57.28 570 / 0.75 1315 / 2893 8000 / 17600 56 / 12320 3000/5700 / 2215/4205* 15 30 / 33000-66000 D25H-P-100HD 1000 / 39.37 2050 / 80.71 1440 / 56.29*** 650 / 0.85 1450 / 3190*** 7000 / 15400 60 / 13200 5700 / 4205** 18-28 / 39600-61600 D27H-P-120HD 1200 / 47.24 2050 / 80.71 1440 / 56.29*** 760 / 0.99 1495 / 3289*** 8000 / 17600 60 / 13200 5700 / 4205** 20-30 / 44000-66000 D32H-P-110HD 1100 / 43.34 2195/ 86.42 1565 / 61.61 825 / 1.08 1820 / 4004 10500 / 23100 70 / 15400 7000 / 5165** 20 40 / 44000-88000 D40H-P-125HD 1250 / 49.21 2355 / 92.72 1640 / 64.57 960 / 1.26 2210 / 4422 13500 / 29700 80 / 17600 7000 / 5165** 25 50 / 55000-110000 D50H-P-140HD 1400 / 55.12 2355 / 92.72 1650 / 64.96 1075 / 1.41 2330 / 5126 16500 / 36300 80 / 17600 7000 / 5165** 35 60 7700-132000 D70H-P-150HD 1500 / 59.05 2730 / 107.38 1930 / 75.98 1660 / 2.17 4000 / 8800 23500 / 51700 140 / 30800 9000 / 6640** 50 80 / 110000-176000 Package consists of: demolition and sorting grab, integrated rotation with sturdy slewing ring, cutting edges and non-return valve Optional second heavy duty motor for D19H-P HD, D20H-P HD, D24H-P HD Notes: * optional with 2 motors for rotation ** second heavy duty hydraulic motor comes standard *** incl. CW4 (integrated) ccessories KM 690 different sized adapters for rigid mounting for excavators up to 70t / 154000 lbs OQ KSW rigid bolt-on adapter for Oilquick OQ 5t up to 70t / 11000 lbs up to 154000 lbs bolt-on-adapter for System L-Lock KMS/KHS for rigid mounting up to 40t / 88000 lbs adapters for quick change systems from other manufacturers or different sizes available on request Operating pressure (open/close): Recommended oil flow (open/close): Operating pressure (rotation): Recommended oil flow (rotation): D25H-P-HD D15 - D70: max. 35 MPa (350 bar) / 5040 psi D15 / D16: max. 80 l/min / max. 21.14 GPM; D19 - D27: max. 100 l/min / max. 26.42 GPM; D32 - D50: max.120 l/min / max. 31.70 GPM; D70: max. 200 l/min / max. 52.84 GPM D15 - D70: max. 14 Mpa (140 bar) / 2016 psi D15 - D24: max. 40 l/min / max. 10.57 GPM; D25 - D70: 40 - max. 60 l/min / 10.57 - max. 15.85 GPM D32H-P-HD
INFO & CONTCT The KINSHOFER Demolition and Sorting Grabs of the D-series were developed especially for the demolition and sorting of construction materials and debris of all kind. The robust, fully integrated rotation with internal hose connections is perfectly protected against external forces. The smallest grab of the series D12H-P is equipped with a flat 15t-rotator. On the standard version, the hydraulic quick change adapter is mounted directly on the head plate. On the version wuth integrated adapter, rotation and adapter are direcly connected to each other, resulting in a lower overall height. The integrated pressure relief valve avoids peak-pressures in the rotation. Two strong hydraulic cylinders that are fully protected in the shell carrier provide for high closing forces. The end position (grab open) is hydraulically cushioned to avoid damage to the cylinders when the grab is pushed into the material. The perforated shells or metal ribs let fine dust and gravel through without large pieces getting caught. The durable, replaceable and indexable wear blades (HB 500) enable the grabs to pinch with their edges without excessive wear. Nederland: DEMREC Demolition and Recycling Equipment B.V. De Hork 32 NL-5431 NS Cuijk Tel.: +31 (0) 485 442300 Fax: +31 (0) 485 442120 info@demarec.com www.demarec.com Sverige: RF System B Furutorpsgatan 6 SE-288 34 Vinslöv Tel.: +46 (0) 44 817 07 Fax: +46 (0) 44 859 63 Email: info@rf-system.se www.rf-system.se United Kingdom: uger Torque Europe Limited Hazleton Cheltenham, GL54 4DX Tel.: +44 (0) 1451 861 652 Fax: +44 (0) 1451 861 660 Email: sales@augertorque.com www.augertorque.com ustralia: uger Torque ustralia Pty Ltd. 122 Boundary Road, Rocklea Queensland 4106 Tel.: +61 (0) 7 3274 2077 Fax: +61 (0) 7 3274 5077 Email: sales@augertorque.com.au www.augertorque.com.au 中国 : uger Torque China CO., Ltd. Baozhan Rd, Tongyi Industry Zone Dongwu, Yinzhou, Ningbo China 315114 Tel.: + 86 (0) 574 8848 8181 Fax: + 86 (0) 574 8848 8687 Email: john.hu@attachmenttorque.com www.augertorque.com Hauptsitz Deutschland: Kinshofer GmbH Hauptstrasse 76 83666 Waakirchen Tel.: +49 (0) 8021 88 99 0 Fax: +49 (0) 8021 88 99 37 Email: info@kinshofer.com www.kinshofer.com United Kingdom: Kinshofer UK Ltd. 4 Milton Industrial Court Horsfield Way, Bredbury Stockport, Cheshire, SK6 2T Tel.: +44 (0) 161 406 7046 Fax: +44 (0) 161 406 7014 Email: sales-uk@kinshofer.com www.kinshofer.com France: Kinshofer France S..R.L. 8 Bis, rue Gabriel Voisin, CS 40003 F-51688 Reims Cedex 2 Tel.: +33 (0) 3 88 39 55 00 Fax: +33 (0) 3 88 79 06 75 Email: sales-france@kinshofer.com www.kinshofer.com EX-D-Grabs-E-2018 Canada: Kinshofer North merica 5040 Mainway Drive, Unit #11 Burlington, ON L7L 7G5 Tel.: +1 (905) 335-2856 Fax: +1 (905) 335-4529 Toll Free (North merica): 1-800-268-9525 Email: sales-northamerica@kinshofer.com www.kinshofer.com United States of merica: Kinshofer US 6420 Inducon Drive Suite G Sanborn, NY, 14132 Tel.: +1 (716) 731-4333 Toll Free (North merica): 1-800-268-9525 Email: sales-usa@kinshofer.com www.kinshofer.com NEW D-GRB SERIES WITH OR WITHOUT HPXdrive: 2t - 4t / 4t - 6t / 6t - 9t United States of merica: Solesbee s Equipment & ttachments, LLC 2640 Jason Industrial Parkway Winston, G 30187 Toll Free (North merica): 1-800-419-8090 Email: sales@solesbees.com www.solesbees.com New Zealand: Doherty Couplers & ttachments PO Box 9339, Greerton Tauranga 3142 Tel.: +64 7 574 3000 Fax: +64 7 574 8030 Email: sales@dohertydirect.net www.dohertydirect.net www.kinshofer.com KINSHOFER is an ISO 9001 certified Company. DVS ZERT is a registred trademark of DVS ZERT e.v., Düsseldorf.