NETAFIM DRIP DRIPPERLINE & FITTING SELECTION - THINWALL SELECTION GUIDE BY DRIPPERLINES - THIN WALLED RING CONNECTORS FLARE CONNECTORS NUT TWIST LOC CONNECTORS Dripperline 16mm 12mm 16mm 16mm 12 DripNet PC 12250 16 Streamline 16040 Streamline 16060 Streamline 16080 DripNet PC 16125 DripNet PC 16150 CONNECTORS TEHCNICAL DATA - THIN WALLED DRIPPERLINE SUB-SURFACE INSTALLATION LAYOUT/RECOILING REUSABLE INTERNAL DIAMETER WALL THICNESS DEEP BURYING SHALLOW BURYING Connectors for Thin/Medium walled dripperlines RING FAST CONN. 16 blue ring 16.2 4-15 mil 16 black/white ring 15.5 20-25 mil 22 blue ring 22.2 8-15 mil 25 black ring 25.0 13.5-15 mil FLARE for TWD (BLUE NUT) 12 11.8 6-25 mil 16 16.2 4-20 mil 22 22.2 8-25 mil 25 25.0 13.5-15 mil 35 35.0 13.5-15 mil TWIST LOC (TWD) 16 16.2 4-20mil 22 22.2 8-25mil 25 25.0 13.5-25 mil Suitable Not suitable / Suitable but not recommended / / / / / / / T148
NETAFIM DRIP DRIPPERLINE & FITTING SELECTION - THICWALL CONNECTORS TECHNICAL DATA - THIC WALLED INTERNAL DIAMETER Connectors for Thick walled dripperlines BARB 12 16 17 20 BARB for MINING (VIOLET) 12 16 17 18 20 FLARE for HWD (ORANGE NUT) 10.2 14.2 14.6 17.5 10.2 14.2 14.6 15.5 17.5 DRIPPERLINE WALL THICNESS 1.0-1.2 mm 0.9-1.2 mm 1.2 mm 1.0-1.2 mm 1.0-1.2 mm 0.9-1.2 mm 1.2 mm 1.1 mm 1.0-1.2 mm SUB-SURFACE INSTALLATION DEEP BURYING SHALLOW BURYING LAYOUT/RECOILING REUSABLE 16-17 14.2-14.6 0.9-1.0 mm 20 17.5 0.9-1.0 mm 23 20.8 0.9-1.0 mm Suitable Not suitable / Suitable but not recommended SELECTION GUIDE BY DRIPPERLINES - THIC WALLED BARB CONNECTORS FLARE CONNECTORS 12 16 17 20 23 Dripperline 12mm 16mm 17mm 20mm 16/17mm 20mm 23mm Tiran 12010 Tiran 12012 UniRam 16009 DripNet PC 16009 Tiran 16009 UniRam 16010 DripNet PC 16010 Tiran 16010 UniRam 16012 DripNet PC 16012 Tiran 16012 UniRam 17012 Tiran 17012 UniRam 20010 DripNet PC 20010 Tiran 20010 UniRam 20012 DripNet PC 20012 Tiran 20012 DripNet PC 23009 UniRam 23010 T149
NETAFIM DRIPPERLINE UNIRAM 20 CNL Pressure-compensating range: 1.0-4.0 bar. Anti-Siphon and Anti-Drain mechanism Largest filter in each dripper. Recommended filtration: 130 micron Double TurboNet TM labyrinth with large water passage. To be welded into thick-walled dripperlines (0.9, 1.0 and 1.2 mm). Injected silicon diaphragm. UV resistant. Resistant to standard nutrients used in agricultural UniRam TM drippers meet ISO 9261 Standards with production certified by the Israel Standards Institute (SII) Pressure compensated : Precise and equal amounts of water are delivered over a broad pressure range. 100 uniformity of water and nutrient distribution along the laterals. Anti-Siphon mechanism : Prevents contaminants from being drawn into the dripper. Anti-drain (CNL) system : Eliminates drainage and refill effect, and improves efficiency in pulse irrigation Continuously self flushing : Flushes debris as it is detected, throughout operation, not just at the beginning or end of a cycle, ensuring uninterrupted dripper operation. Self-flushing system with wide filtration area improves resistance to clogging thus making UniRam TM highly resistant when using low quality water. Physical root barrier : Better protection against root intrusion without reliance on chemicals. TurboNet TM labyrinth assures wide water passages, large deep and wide cross section improves clogging resistance. Widest water passages within the dripper. The water is drawn in to the dripper from the stream center, preventing the entrance of sediments in to the drippers. DRIPPERS TECHNICAL DATA WORING PRESSURE RANGE WATER PASSAGES DIMENSIONS WIDTH-DEPTH-LENGTH AREA (MM2) EPONENT * RECOMMENDED (MICRON)/(MESH) SHUT OFF PRESSURE 1.0 1.0 4.0 0.83 x 0.74 x 40 130 1.0 0 130/120 0.14 2.3 1.0 4.0 1.26 x 1.00 x 40 130 2.3 0 130/120 0.14 * Within working pressure range DRIPPERLINES TECHNICAL DATA MODEL INSIDE DIAMETER WALL THICNESS OUTSIDE DIAMETER MA. WORING PRESSURE MAIMUM FLUSHING PRESSURE D 20012 17.5 1.2 19.9 4.0 4.6 0.4 T150
NETAFIM DRIPPERLINE MA. LATERAL LENGTH (METER) AT DIFFERENT INLET PRESSURE AND DIFFERENT SLOPES UNIRAM CNL 20010/20012 ID 17.5 MM D 0.4 1.0 L/H FLAT TERRAIN INLET PRESSURE 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.5 109 140 162 178 190 200 208 214 219 2.0 149 198 236 268 295 316 335 352 366 2.5 177 238 288 331 367 398 426 451 473 3.0 199 269 328 380 424 463 498 530 558 3.5 217 296 362 420 472 517 558 596 630 4.0 233 318 392 456 512 564 610 653 692 1.5 133 185 232 276 316 353 389 423 456 2.0 169 236 296 352 403 452 498 542 583 2.5 194 272 341 406 465 522 574 626 674 3.0 215 300 378 449 515 577 636 693 747 3.5 232 325 408 485 557 624 689 750 809 4.0 247 346 435 518 594 666 734 800 863 1.5 157 233 308 382 455 528 601 673 745 2.0 189 275 358 439 518 596 674 750 826 2.5 212 306 396 483 568 650 731 812 891 3.0 230 332 428 520 609 696 781 864 947 3.5 247 354 455 552 645 736 824 911 996 4.0 261 374 480 581 677 771 863 953 1041 Minimum considered pressure 0.1 bar Max. working pressure according the dripperline wall thickness definition Due to lateral filling time and flushing effectiveness it is not recommended to exceed 800 meters lateral length MA. LATERAL LENGTH (METER) AT DIFFERENT INLET PRESSURE AND DIFFERENT SLOPES UNIRAM CNL 20010/20012 ID 17.5 MM D 0.4 2.3 L/H INLET PRESSURE 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.5 69 92 110 126 139 150 159 167 175 2.0 91 124 152 176 197 216 233 248 263 2.5 107 146 181 211 238 262 284 304 323 3.0 119 164 203 238 269 298 324 348 371 3.5 129 179 222 261 296 328 358 385 411 4.0 138 192 238 281 319 354 386 417 446 FLAT TERRAIN 1.5 77 108 136 161 184 207 228 248 267 2.0 98 137 173 205 235 264 291 317 342 2.5 113 158 199 237 272 305 336 366 395 3.0 124 175 220 262 301 337 372 405 437 3.5 134 189 238 283 325 365 402 439 473 4.0 143 201 254 302 347 389 430 468 505 1.5 85 124 161 197 232 267 302 335 369 2.0 105 150 194 235 275 314 351 389 425 2.5 119 170 217 263 307 349 390 430 469 3.0 130 185 237 286 332 378 422 464 506 3.5 139 199 254 306 355 403 449 494 537 4.0 148 210 268 323 375 425 474 520 566 Minimum considered pressure 0.1 bar Max. working pressure according the dripperline wall thickness definition T151
NETAFIM DRIPPERLINE UNIRAM RC 16010 Pressure-compensating range: 0.5-4.0 bar. Largest filter in each dripper. Recommended filtration: according to drippers flow rate Double TurboNet TM labyrinth with large water passage. To be welded into thick-walled dripperlines (0.9, 1.0 and 1.2 mm). Injected silicon diaphragm. UV resistant. Resistant to standard nutrients used in agricultural UniRam TM drippers meet ISO 9261 Standards with production certified by the Israel Standards Institute (SII) Pressure compensated : Precise and equal amounts of water are delivered over a broad pressure range. 100 % uniformity of water and nutrient distribution along the laterals. Continuously self flushing : Flushes debris as it is detected, throughout operation, not just at the beginning or end of a cycle, ensuring uninterrupted dripper operation. Self-flushing system with wide filtration area improves resistance to clogging thus making UniRamTM highly resistant when using low quality water. Physical root barrier : Better protection against root intrusion without reliance on chemicals. TurboNet TM labyrinth assures wide water passages, large deep and wide cross section improves clogging resistance. Widest water passages within the dripper. The water is drawn in to the dripper from the stream center, preventing the entrance of sediments in to the drippers. DRIPPERS TECHNICAL DATA WORING PRESSURE RANGE WATER PASSAGES DIMENSIONS WIDTH-DEPTH-LENGTH AREA (MM2) EPONENT * RECOMMENDED (MICRON)/(MESH) 1.6 0.5-4.0 1.26 x 0.70 x 40 130 1.6 0 200/80 * Within working pressure range DRIPPERLINES TECHNICAL DATA MODEL INSIDE DIAMETER WALL THICNESS OUTSIDE DIAMETER MA. WORING PRESSURE MAIMUM FLUSHING PRESSURE D 16010 14.2 1.0 16.2 3.5 4.0 1.3 MA. LATERAL LENGTH (METER) AT DIFFERENT INLET PRESSURE AND DIFFERENT SLOPES UNIRAM RC 16009/16010/16012 ID 14.2 MM D 1.3 1.6 L/H INLET PRESSURE 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.0 51 71 88 103 116 127 138 147 155 1.5 67 95 119 141 160 179 195 210 224 2.0 78 110 140 166 191 214 234 254 272 2.5 86 123 156 187 214 241 265 288 309 3.0 93 133 170 204 235 263 290 316 340 3.5 100 143 182 218 251 284 313 341 367 4.0 105 151 192 231 267 301 333 363 391 FLAT TERRAIN 1.0 56 80 103 124 144 163 182 200 216 1.5 70 101 130 158 184 208 231 254 276 2.0 81 116 150 181 211 239 266 293 318 2.5 89 128 165 200 233 265 294 324 352 3.0 96 139 178 216 252 286 318 350 380 3.5 102 147 190 230 268 305 339 373 405 4.0 108 155 200 243 283 321 358 393 428 T152 Minimum considered pressure 0.5 bar 1.0 60 89 117 145 173 200 228 255 282 1.5 74 108 142 175 206 238 269 299 329 2.0 84 122 160 197 232 266 300 333 365 2.5 92 134 175 214 252 289 325 360 395 3.0 98 144 187 229 269 309 346 384 421 3.5 104 152 198 242 285 326 366 405 444 4.0 110 160 208 254 299 342 384 425 464 Max. working pressure according the dripperline wall thickness definition
NETAFIM DRIPPERLINE DRIPNET PC 16010 Pressure-compensating range: 0.4-2.5/3.0 bar (according to flow rate model). Recommended filtration: according to drippers flow rate TurboNet TM labyrinth with large water passage. To be welded into thick-walled dripperlines (0.9, 1.0 and 1.2 mm). Injected silicon diaphragm. UV resistant. Resistant to standard nutrients used in agricultural DripNet PC TM drippers meet ISO 9261 Standards with production certified by the Israel Standards Institute (SII) Pressure compensated : Precise and equal amounts of water are delivered over a broad pressure range. 100 % uniformity of water and nutrient distribution along the laterals. Continuously self flushing : Flushes debris as it is detected, throughout operation, not just at the beginning or end of a cycle, ensuring uninterrupted dripper operation. Self-flushing system with wide filtration area improves resistance to clogging. TurboNet TM labyrinth assures wide water passages, large deep and wide cross section improves clogging resistance. Widest water passages within the dripper. The water is drawn in to the dripper from the stream center, preventing the entrance of sediments in to the drippers. D R I PPERS T E C HN IC AL DATA F LO W RATE WOR I NG PRESSURE RANGE ( B AR) WATER PASSAGES D I MENS I ONS W I DTH-DEPTH-LENGTH FI LTRAT I ON AREA (MM2) E PONENT * R E C OMMENDED FI LTRAT I ON (M IC RON)/(MESH) 1.0 0.40-3.0 0.61 x 0.60 x 8 39 1.0 0 130/120 1.6 0.40-3.0 0.76 x 0.73 x 8 39 1.6 0 200/80 * Within working pressure range DRIPPERLINES TECHNICAL DATA MODEL INS IDE DIAMETER WALL THICNESS OUTSIDE DIAMETER MA. WORING PRESSURE MAIMUM FLUSHING PRESSURE D 16010 14.2 1.0 16.2 3.0 3.5 0.72 *Maximum working pressure is defined by the dripper and not by the dripperline wall thickness MA. LATERAL LENGTH (METER) AT DIFFERENT INLET PRESSURE AND DIFFERENT SLOPES DRIPNET PC 16009/16010/16012 ID 14.2 MM D 0.72 1.0 L/H INLET PRESSURE 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.0 83 111 134 153 169 183 194 205 214 1.5 106 145 178 207 232 253 274 292 308 2.0 122 169 209 244 275 304 330 354 375 2.5 135 188 234 274 311 344 374 403 429 FLAT TERRAIN 1.0 92 130 165 197 226 255 282 307 331 1.5 114 161 204 243 280 315 349 381 411 2.0 129 183 232 277 320 360 398 434 469 2.5 142 201 255 305 352 396 438 478 517 Minimum considered pressure 0.4 bar 1.0 102 150 196 242 287 330 374 418 461 1.5 122 177 230 281 331 379 426 473 520 2.0 136 197 255 311 364 417 468 518 567 2.5 148 214 276 336 393 449 502 555 607 T153
NETAFIM DRIPPERLINE DRIPNET THINWALL Pressure-compensating range: 0.25/0.40/0.60-2.5/3.0/3.5 bar (according to flow rate model & dripperlines wall-thickness). Recommended filtration: according to drippers flow rate TurboNet TM labyrinth with large water passage. A wide assortment of dripperlines wall thickness models (0.31, 0.34, 0.38, 0.50, and 0.63 mm). Injected silicon diaphragm. UV resistant. Resistant to standard nutrients used in agricultural DripNet PC TM drippers meet ISO 9261 Standards with production certified by the Israel Standards Institute (SII) Pressure compensated : Precise and equal amounts of water are delivered over a broad pressure range. 100% uniformity of water and nutrient distribution along the laterals. Continuously self flushing : Flushes debris as it is detected, throughout operation, not just at the beginning or end of a cycle, ensuring uninterrupted dripper operation. Self-flushing system with wide filtration area improves resistance to clogging. TurboNet TM labyrinth assures wide water passages, large deep and wide cross section improves clogging resistance. Widest water passages within the dripper. The water is drawn into the dripper from the stream center, preventing the entrance of sediments in to the drippers. D R I PPERS T E C HN IC AL DATA F LOW RATE W OR I NG PRESSURE RANGE ( B AR) W ATER PASSAGES D I MENS I ONS WI DTH-DEPTH-LENGTH FI LTRAT I ON AREA (MM2) E PONENT * R E C OMMENDED FI LTRAT I ON (M IC RON)/(MESH) 0.6 0.25-2.5 0.52 x 0.60 x 22 39 0.6 0 130/120 1.0 0.40-3.0 0.61 x 0.60 x 8 39 1.0 0 130/120 * Within working pressure range D R I PPERL I NES T E C HN IC AL DATA M ODEL INS I DE D I AMETER W ALL TH IC NESS O UTS I DE D I AMETER M A. WOR I NG PRESSURE ( B AR) M A I MUM FLUSH I NG PRESSURE ( B AR) 12250 11.8 0.63 13.06 3.0* 3.9 1.35 16125 16.2 0.31 16.82 1.8 2.1 0.40 16150 16.2 0.38 16.96 2.2 2.5 0.40 *Maximum working pressure is defined by the dripper and not by the dripperline wall thickness M A. LATERAL LENGTH (METERS) AT D I FFERENT I NLET PRESSURE AND D I FFERENT SLOPES DRIPNET P C 12125/12150/12200/12250 I D 11.8 MM D 1.35 0.6 L/H U PH I LL INLET PRESSURE ( B AR) DI STAN C E B ETWEEN DR I PPERS (METER) 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.0 77 105 129 148 164 179 191 202 211 1.5 98 137 170 198 224 246 267 285 302 2.0 114 159 198 234 266 295 321 345 367 2.5 126 176 222 262 299 333 364 392 419 D F LAT TERRA I N 1.0 86 122 156 188 217 245 272 298 323 1.5 105 151 192 232 268 303 337 368 399 2.0 120 171 219 264 306 346 384 420 456 2.5 131 188 240 290 336 380 422 463 501 T154 D OWNH I LL Minimum considered pressure 0.4 bar 1.0 94 139 184 228 272 315 358 401 444 1.5 112 165 216 266 314 362 409 455 501 2.0 126 184 240 294 347 398 449 499 547 2.5 137 200 260 318 374 428 482 535 586 Max. working pressure acoording the dripperline wall thickness definition
NETAFIM DRIPPERLINE MA. LATERAL LENGTH (METERS) AT DIFFERENT INLET PRESSURE AND DIFFERENT SLOPES DRIPNET PC 16125/16150 ID 16.2 MM D 0.4 0.6 L/H FLAT TERRAIN INLET PRESSURE 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.0 141 178 204 223 237 248 256 263 268 1.4 180 234 276 308 334 356 374 389 401 1.8 209 275 329 373 409 440 466 488 508 2.2 232 309 372 425 469 508 542 571 597 1.0 176 244 305 361 413 461 508 552 594 1.4 210 292 365 432 494 553 609 662 713 1.8 236 328 411 487 557 624 686 746 804 2.2 257 358 449 532 609 682 750 816 879 1.0 211 313 414 513 612 706 791 875 957 1.4 240 351 459 564 668 767 858 947 1034 1.8 263 382 496 607 715 818 914 1008 1100 2.2 283 408 528 643 755 863 963 1061 1157 Minimum considered pressure 0.4 bar Max. working pressure acoording the dripperline wall thickness definition Due to lateral filling time and flushing effectiveness it is not recommended to exceed 800 meters lateral length MA. LATERAL LENGTH (METERS) AT DIFFERENT INLET PRESSURE AND DIFFERENT SLOPES DRIPNET PC 16125/16150 ID 16.2 MM D 0.4 1.0 L/H INLET PRESSURE 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.0 108 140 166 185 201 214 225 233 241 1.4 135 179 215 245 271 292 310 327 341 1.8 155 208 252 290 322 351 376 399 419 2.2 171 232 282 326 365 399 430 457 482 FLAT TERRAIN 1.0 126 175 219 260 297 333 366 398 428 1.4 150 209 262 311 356 398 438 477 514 1.8 169 236 295 350 401 449 494 537 579 2.2 184 257 322 382 438 491 540 588 633 1.0 144 211 276 339 401 463 523 584 644 1.4 166 240 311 379 446 511 576 639 702 1.8 183 263 339 412 482 552 619 685 751 2.2 197 283 363 440 514 586 656 725 793 Minimum considered pressure 0.4 bar Max. working pressure acoording the dripperline wall thickness definition T155
NETAFIM DRIPPERLINE STREAMLINE Recommended filtration: 130 micron / 120 mesh TurboNet TM labyrinth with large water passage. To be welded into a thin-walled dripperlines (0.15, 0.20, 0.25, and 0.31 mm). UV resistant. Resistant to standard nutrients used in agricultural Streamline TMTM drippers meet ISO 9261 Standards with production certified by the Israel Standards Institute (SII) Wide filtration area to ensure optimal performance. TurboNet TM labyrinth assures wide water passages, large deep and wide cross section improves clogging resistance The water is drawn in to the dripper from the stream center, preventing the entrance of sediments in to the drippers. Injection molded dripper construction, ensuring uniform drippers and very low CV DRIPPERS TECHNICAL DATA 12060 & 16060-0.15 mm. wall thickness dripperlines * MA. WORING PRESSURE** WATER PASSAGES DIMENSIONS WIDTH-DEPTH-LENGTH AREA (MM2) EPONENT RECOMMENDED (MICRON)/(MESH) 0.80 1.4/0.8 0.58 x 0.33 x 25 14 0.265 0.48 130/120 1.10 1.4/0.8 0.51 x 0.42 x 13 15 0.392 0.45 130/120 * Flow rate at 1.0 bar pressure **According to dripperlines inside diameter 16080-0.20 mm. wall thickness dripperlines * MA. WORING PRESSURE** WATER PASSAGES DIMENSIONS WIDTH-DEPTH-LENGTH AREA (MM2) EPONENT RECOMMENDED (MICRON)/(MESH) 0.72 1.7/1.0/0.8 0.58 x 0.33 x 25 14 0.238 0.48 130/120 1.05 1.7/1.0/0.8 0.51 x 0.42 x 13 15 0.373 0.45 130/120 * Flow rate at 1.0 bar **According to dripperlines inside diameter DRIPPERLINES TECHNICAL DATA MODEL INSIDE DIAMETER WALL THICNESS OUTSIDE DIAMETER MA. WORING PRESSURE MAIMUM FLUSHING PRESSURE D 16060 16.2 0.15 16.50 0.80 0.9 0.10 16080 16.2 0.20 16.60 1.00 1.2 0.10 T156
NETAFIM DRIPPERLINE MA. LATERAL LENGTH (METERS) AT DIFFERENT SLOPES - 10% FLOW VARIATION STREAMLINE 16060 ID 16.2 MM D 0.1 0.8 L/H INLET PRESSURE 0.8 BAR SLOPE 0.20 0.30 0.40 0.50 0.60 0.70 0.80 65 71 74 75 76 77 78 1% 89 107 118 127 132 137 140 FLAT TERRAIN 0 122 162 197 229 259 286 313-1% 153 218 281 344 407 470 231-186 103 88 84 82 81 81 MA. LATERAL LENGTH (METERS) AT DIFFERENT SLOPES - 10% FLOW VARIATION STREAMLINE 16060 ID 16.2 MM D 0.1 1.1 L/H INLET PRESSURE 0.8 BAR SLOPE 0.20 0.30 0.40 0.50 0.60 0.70 0.80 65 74 79 82 84 85 86 1% 82 101 115 125 134 140 146 FLAT TERRAIN 0 103 138 168 195 220 244 266-1% 121 170 218 264 309 354 399-142 208 276 98 92 90 88 MA. LATERAL LENGTH (METERS) AT DIFFERENT SLOPES - 10% FLOW VARIATION STREAMLINE 16080 ID 16.2 MM D 0.1 0.72 L/H INLET PRESSURE 1.0 BAR SLOPE 0.20 0.30 0.40 0.50 0.60 0.70 0.80 76 85 89 92 94 95 95 1% 101 122 137 148 157 163 168 FLAT TERRAIN 0 132 176 214 248 280 311 339-1% 162 228 292 356 418 481 544-192 284 120 110 106 104 102 MA. LATERAL LENGTH (METERS) AT DIFFERENT SLOPES - 10% FLOW VARIATION STREAMLINE 16080 ID 16.2 MM D 0.1 1.05 L/H INLET PRESSURE 1.0 BAR SLOPE 0.20 0.30 0.40 0.50 0.60 0.70 0.80 73 85 93 98 101 104 105 1% 90 112 128 142 152 161 168 FLAT TERRAIN 0 108 144 176 205 231 256 279-1% 124 173 219 264 308 351 394-142 205 268 333 128 119 114 T157
NETAFIM CNL DRIPPERS PCJ LCNL Working pressure range: 0.7 to 4.0 bar TurboNet TM labyrinth with large water passages. 7 different flow rates. 3 different outlets: nipple, barb to 3 mm ID and barb to 4 mm ID. To be inserted into thick- walled pipes (0.9, 1.0 and 1.2 mm.). Injected silicon diaphragm. PCJ LCNL, On line dripper meet ISO 9261 standards and production is certified by the Israel Standards Institute (SII) TurboNet TM labyrinth assures wide water passages, large deep and wide cross section improves clogging resistance. PC system, patented pressure differential system maintains uniform flow rate at different inlet working pressure (in the recommended working pressure range), ensuring exact distribution of the water and nutrients. Continuous self-flushing system, improves resistance to clogging. Dripper can be positioned exactly where required. Number of drippers can be increased so as to increase water quantity supply aimed at meeting tree growth rate requirement. Allows the installation of spider assembly, splitting the drip supply to a number of drip outlets. PCJ LCNL with Anti-drain system for efficient pulse irrigation, prevents water drainage and eliminates needs for refill. DRIPPERS TECHNICAL DATA NOMINAL FLOW RATE WORING PRESSURE RANGE WATER PASSAGES DIMENSIONS WIDTH-DEPTH-LENGTH (MM MM MM) AREA (MM²) EPONENT* SHUT OFF PRESSURE BASE CODE COLOR** CAP COLOR CODE 1.2 0.7 4.0 0.67 x 0.77 x 35 2.0 1.2 0 0.12 Brown Black 2.0 0.7 4.0 1.03 x 0.75 x 35 2.0 2.0 0 0.12 Red Black 3.0 0.7 4.0 1.03 x 1.08 x 35 2.0 3.0 0 0.12 Blue Black 4.0 0.7 4.0 1.32 x 0.95 x 35 2.0 4.0 0 0.12 Gray Black 8.0 0.7 4.0 1.60 x 1.05 x 35 2.0 8.0 0 0.12 Green Black *Within working pressure range **In addition, PCJ-LCNL is distinguished by the rings around the barb water inlet connector DRIPPER PICTURE DRIPPER MODEL PCJ-LCNL dripper with 3 mm.barb outlet PCJ-LCNL dripper with nipple outlet T158
NETAFIM CNL DRIPPERS PERFORMANCE DATA PCJ LCNL dripper - PE pipe 16/2.5 - I.D. 13.60 mm. - Inlet pressure 3.0 bar - d 0.39 Maximum lateral length (meter) SPACING BETWEEN DRIPPERS (M.) 0.25 0.5 0.75 1.0 1.5 3.0 5.0 0.5 291 494 661 808 1067 1689 2360 1.2 165 281 377 461 609 966 1350 2.0 118 202 272 332 440 699 975 3.0 91 156 209 256 339 540 755 4.0 75 129 174 213 282 450 630 8.0 48 83 112 137 182 291 405 12.0 37 64 86 106 141 225 315 *Calculated in a plain area **Minimum considered pressure : 0.7 bar PCJ LCNL dripper - PE pipe 20/2.5 - I.D. 17.40 mm. - Inlet pressure 3.0 bar - d 0.13 Maximum lateral length (meter) SPACING BETWEEN DRIPPERS (M.) 0.25 0.5 0.75 1.0 1.5 3.0 5.0 0.5 487 797 1049 1272 1662 2610 3625 1.2 277 454 599 727 951 1494 2075 2.0 199 328 432 524 686 1077 1500 3.0 154 253 334 405 530 834 1160 4.0 128 210 278 337 441 693 965 8.0 82 135 179 216 284 447 620 12.0 63 104 137 167 219 345 480 *Calculated in a plain area **Minimum considered pressure : 0.7 bar PCJ LCNL dripper - PE pipe 25/2.5 - I.D. 22.20 mm. - Inlet pressure 3.0 bar - d 0.10 Maximum lateral length (meter) SPACING BETWEEN DRIPPERS (M.) 0.25 0.5 0.75 1.0 1.5 3.0 5.0 0.5 740 1211 1596 1934 2528 3969 5515 1.2 421 690 911 1105 1446 2271 3155 2.0 303 498 657 797 1043 1641 2280 3.0 233 384 507 615 806 1266 1760 4.0 194 319 422 512 671 1053 1465 8.0 124 205 271 329 431 678 945 12.0 95 158 209 254 333 525 730 *Calculated in a plain area **Minimum considered pressure : 0.7 bar For more information, please contact Netafim Technical Department or connect to our website at : www.netafim.com T159
NETAFIM CNL DRIPPERS PCJ HCNL Working pressure range: 1.5 to 4.0 bar. TurboNet TM labyrinth with large water passages. 5 different flow rates. 3 different outlets: nipple, barb to 3 mm ID and barb to 4 mm ID. To be inserted into thick- walled pipes (0.9, 1.0 and 1.2 mm.). Injected silicon diaphragm. PCJ HCNL, On line dripper meet ISO 9261 standards and production is certified by the Israel Standards Institute (SII) TurboNet TM labyrinth assures wide water passages, large deep and wide cross section improves clogging resistance. PC system, patented pressure differential system maintains uniform flow rate at different inlet working pressure (in the recommended working pressure range), ensuring exact distribution of the water and nutrients. Continuous self-flushing system, improves resistance to clogging. Dripper can be positioned exactly where required. Number of drippers can be increased so as to increase water quantity supply aimed at meeting tree growth rate requirement. Allows the installation of spider assembly, splitting the drip supply to a number of drip outlets. PCJ-HCNL with Anti-drain system for efficient pulse irrigation, prevents water drainage and eliminates needs for refill. DRIPPERS TECHNICAL DATA NOMINAL FLOW RATE WORING PRESSURE RANGE WATER PASSAGES DIMENSIONS WIDTH-DEPTH-LENGTH (MM MM MM) AREA (MM²) EPONENT* SHUT OFF PRESSURE BASE CODE COLOR CAP COLOR CODE 1.2 1.5 4.0 0.67 x 0.77 x 35 2.0 1.2 0 0.18 Light brown Black 2.0 1.5 4.0 1.03 x 0.75 x 35 2.0 2.0 0 0.18 Pink Black 3.0 1.5 4.0 1.03 x 1.08 x 35 2.0 3.0 0 0.18 Light blue Black 4.0 1.5 4.0 1.32 x 0.95 x 35 2.0 4.0 0 0.18 Light gray Black *Within working pressure range PERFORMANCE DATA PCJ HCNL dripper - PE pipe 16/2.5 - I.D. 13.60 mm. - Inlet pressure 3.0 bar - d 0.39 Maximum lateral length (meter) SPACING BETWEEN DRIPPERS (M.) 0.25 0.5 0.75 1.0 1.5 3.0 5.0 0.5 250 424 568 694 915 1449 2020 1.2 142 241 323 396 522 828 1160 2.0 102 174 233 285 377 600 835 3.0 78 134 180 220 291 462 645 4.0 65 111 149 183 243 387 540 *Calculated in a plain area **Minimum considered pressure : 1.5 bar PCJ HCNL dripper - PE pipe 20/2.5 - I.D. 17.40 mm. - Inlet pressure 3.0 bar - d 0.13 Maximum lateral length (meter) SPACING BETWEEN DRIPPERS (M.) 0.25 0.5 0.75 1.0 1.5 3.0 5.0 0.5 419 684 900 1091 1425 2235 3105 1.2 238 390 514 623 815 1281 1780 2.0 171 281 371 450 588 924 1285 3.0 132 217 286 347 455 714 995 4.0 110 180 238 289 378 594 830 *Calculated in a plain area **Minimum considered pressure : 1.5 bar T160 PCJ HCNL dripper - PE pipe 25/2.5 - I.D. 22.20 mm. - Inlet pressure 3.0 bar - d 0.10 Maximum lateral length (meter) SPACING BETWEEN DRIPPERS (M.) 0.25 0.5 0.75 1.0 1.5 3.0 5.0 0.5 636 1039 1369 1659 2168 3402 4725 1.2 362 593 782 948 1239 1947 2705 2.0 260 427 563 684 894 1404 1955 3.0 200 329 435 528 690 1086 1510 4.0 166 274 362 439 575 903 1260 *Calculated in a plain area **Minimum considered pressure : 1.5 bar For more information, please contact Netafim Technical Department or connect to our website at : www.netafim.com
NETAFIM CNL DRIPPERS PC CNL DRIPPERS Recommended filtration: 130 micron / 120 mesh TurboNet TM labyrinth with large water passage. To be inserted into thick-walled pipes (0.9, 1.0 and 1.2 mm.) UV resistant. Resistant to standard nutrients used in agricultural PC on-line drippers meet ISO 9261 Standards with production certified by the Israel Standards Institute (SII) Pressure compensated : Precise and equal amounts of water are delivered over a broad pressure range. 100 % uniformity of water and nutrient distribution along the laterals. PC-LCNL & PC-HCNL with Anti-drain (LCNL & HCNL) : Eliminates drainage and refill effect, and improves efficiency in pulse irrigation Continuously self flushing : Flushes debris as it is detected, throughout operation, not just at the beginning or end of a cycle, ensuring uninterrupted dripper operation. TurboNet TM labyrinth assures wide water passages, large deep and wide cross section improves clogging resistance. Widest water passages within the dripper. Dripper can be positioned exactly where required. Number of drippers can be increased so as to increase water quantity supply aimed at meeting tree growth rate requirement. Allows the installation of spider assembly, splitting the drip supply into a number of drip outlets. DRIPPERS TECHNICAL DATA PC-LCNL drippers WORING PRESSURE RANGE WATER PASSAGES DIMENSIONS WIDTH-DEPTH-LENGTH AREA (MM2) EPONENT* SHUT OFF PRESSURE 2.0 1.0 4.0 1.17 x 1.07 x 61 2.0 2.0 0 0.15 Red Brown 4.0 1.0 4.0 1.32 x 1.40 x 60 2.0 4.0 0 0.15 Black Brown 8.5 1.0 4.0 1.60 x 1.60 x 17 2.0 8.5 0 0.15 Green Brown * Within working pressure range PC-HCNL drippers WORING PRESSURE RANGE WATER PASSAGES DIMENSIONS WIDTH-DEPTH-LENGTH AREA (MM2) EPONENT* SHUT OFF PRESSURE 3.0 1.4 4.0 1.17 x 1.07 x 61 2.0 3.0 0 0.30 Black Black 6.0 1.4 4.0 1.32 x 1.40 x 60 2.0 6.0 0 0.30 Black Black 12.0 1.4 4.0 1.60 x 1.60 x 17 2.0 12.0 0 0.30 Black Black * Within working pressure range BASE CODE COLOR BASE CODE COLOR CAP COLOR CODE CAP COLOR CODE T161
NETAFIM NON-COMPENSATED DRIPPERS NON-COMPENSATED DRIPPERS Maximal working pressure: 2.0 bar. TurboNet TM labyrinth with large water passages. 5 different flow rates. The Button model to be inserted into a thick-walled pipe (0.9, 1.0 and 1.2 mm). The Pot model to be threaded into a 3*5 micro-tube. TurboNet TM labyrinth assures wide water passages, large deep and wide cross section improves clogging resistance. Dripper can be positioned exactly where required. Number of drippers can be increased to increase the water quantities applied aimed at meeting tree s growth rate requirements. Allows the installation of spider assembly, splitting the drip supply to a number of drip outlets. D RIPPERS TECHNICAL DATA B utton drippers FL O W RATE (L/H)* MAI M U M W O RING PRESSURE W ATER PASSAGES DI M ENSI O NS W IDTH-DEPTH-LENGTH ( MM.) C O NSTANT EP O NENT B ASIS C O DE C O L O R C AP C O L O R C O DE 1.05 2.0 0.70 x 0.65 x 50 0.347 0.48 Brown Black 2.00 2.0 0.98 x 0.89 x 50 0.662 0.48 Red Black 3.00 2.0 1.05 x 0.95 x 50 0.993 0.48 Blue Black 4.00 2.0 1.27 x 1.20 x 50 1.325 0.48 Black Black 8.00 2.0 1.65 x 1.40 x 50 2.649 0.48 Green Black * Flow rate at 1.0 bar pressure P ot drippers FL O W RATE (L/H)* 1.05 MAI M U M W O RING PRESSURE W ATER PASSAGES DI M ENSI O NS W IDTH-DEPTH-LENGTH ( MM.) C O NSTANT EP O NENT B ASIS C O DE C O L O R C AP C O L O R C O DE 2.0 0.70 x 0.65 x 50 0.347 0.48 Brown Black 2.00 2.0 0.98 x 0.89 x 50 0.662 0.48 Red Black 4.00 2.0 1.27 x 1.20 x 50 1.325 0.48 Black Black 8.00 2.0 1.65 x 1.40 x 50 2.649 0.48 Green Black * Flow rate at 1.0 bar pressure T162
NETAFIM NON-COMPENSATED DRIPPERS ARROW STAES Maximal working pressure: 1.2 bar. Turbulent labyrinth wide water passages for highest reliability and efficiency. 5 different models to meet growers requirements. To be inserted into a 3*5 micro-tube. Allows placement of drippers exactly where necessary. Allows maximum flexibility in greenhouse and nurseries (with soft PE micro- tubes). Allows installation of other Netafim TM drippers to add compensated and anti-drain functionality. Accessory to all on-line drippers for better and more accurate installation. Adaptable to all on-line drippers via barb, manifold or adapter. DRIPPERS TECHNICAL DATA (L/H)* MAIMUM WORING PRESSURE WATER PASSAGES DIMENSIONS WIDTH-DEPTH-LENGTH AREA (MM²) EPONENT 1.6 1.2 0.83 x 0.60 x 20 9.4 0.551 0.48 2.3 1.2 0.83 x 0.86 x 20 12.6 0.761 0.48 *Flow rate at 1.0 bar pressure **Arrow dripper at 1.6 l/h. nominal flow rate, only available in the angle model. T163
PRE-ASSEMBLED DRIP SYSTEMS INSTRUCTIONS FOR THE HANDLING OF PRE-ASSEMBLED DRIP SYSTEMS Drip irrigation systems are manufactured with utmost care. In order for you to achieve perfect results, we have drawn up recommendations on how to store and unroll the drip irrigation system and put it into use. Receipt Upon receipt of the drip lines, check the delivery and sign the consignment note. Any deviations found must be specified on the consignment note and notified to Revaho (as soon as possible, but no later than 48 hours after receipt). Store the drip irrigation line (indoors) out of the sun in order to avoid damage due to high temperatures. Unroll the drip irrigation line within three weeks of receipt in order to avoid unnecessary leakages. Avoid lines being thrown about or treated roughly, as this could damage the drippers. Every order (of 5,000 drippers or more) complimentarily includes a hand perforator and 0.5% extra sets (2 hand perforators for more than 50,000 drippers). We recommend that you save a few of the roll stickers, as they contain information about the production batch, which may be needed in the event of complaints. Unrolling Allow the drip irrigation line to warm up to the greenhouse temperature before unrolling. We strongly recommend that the line is unrolled from a vertical reel, on a tube rail lorry. As polyethylene is sensitive to elongation and contraction, we recommend that you allow for a safety margin of 1- extra length if the lines are attached during warm weather (expansion of polyethylene is 0.0: 2 cm per degree of temperature difference per 100 metres). The lines are supplied with at least 0.5 m extra blind length (without drippers) both before and after the drippers. When inserting the spikes, start in the middle of the line and work towards the ends, thus minimising the need for additional insertion. Extra drippers can easily be added by means of the hand perforator supplied. Holes for Cobra drippers can be reamed with the supplied brass awl. Starting up Polyethylene is resistant to a great variety of chemicals, such as acids, chlorine and fertilisers (the rubber in pressure-compensating drippers is not resistant to chlorine!!). Polyethylene is not resistant to soapy products however. Only use water as a lubricant when mounting the couplings. Make sure that the PE is tightly pressed into the coupling by the rubber ring. Flush the lines thoroughly after installation in order to remove possible dirt. The memory of PE causes the lines to bend or buckle when unrolled. Bends and buckles will generally disappear in a few weeks. Buckles in micro-tubes will hardly ever reduce the water supply and can be simply removed by warming the line. Minor leakages around the perforation will generally disappear. Constriction of the micro-tube may occur if Cobra drippers have become too warm during storage. Pressing the micro-tube a few millimetres deeper into the line will make the seal effective again. Drippers to be replaced must be cut off just above the line rather than being pulled out. Extensive version (for end user) available on request. T164