2-Person Glider Set SKU# 272-0833 MODEL # BJ390 ASSEMBLY AND USER MANUAL IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY The schmatics in this manual are for assembly and operation illustration only. They may differ from the products s actual appearance. If you have any questions, concerns or need additional parts please do not return to the place of purchase. Contact our customer service department toll free at 1-855-880-7205 for further instructions. For additional product information, please contact our Customer Service Center at 1-855-880-7205 between 8am- 5pm Eastern Time, Monday through Friday. 2016 Distributed by Menard, Inc., Eau Claire, WI 54703 Made in China
CONTENTS Warning and Cautions...2 Care and Maintenence....3 Preparation....3 Hardware Contents....4 Package Contents....5 Assembly....................................... 6-10 Warranty....11 Filing a Claim....11 WARNINGS AND CAUTIONS DANGER: Keep children out of the assembly area during assembly. WARNING: Do not stand on the side table or seats. CAUTION: Use table on flat ground only. IMPORTANT: Please check tightness of bolts at least every 180 days. 2
CARE AND MAINTENANCE Use mild soap and warm water to clean the frames. Rinse with clean water and dry thoroughly. Be sure to drain any water accumulated inside the frames. To thoroughly drain frames, remove footcaps and tilt frames, if necessary, to remove all water. Water allowed to accumulate inside the frames and then exposed to sub-freezing temperatures can cause damage to frame tubing. Such damage is not covered under warranty. Any rust spots should be lightly sanded and treated with rust inhibitor and followed with an application of touch-up paint (not included). Small nicks and scratches can be covered with an application of touch-up paint (not included). Use commercially available glass cleaners. Do not use abrasive materials, cleansers or bleach products. Hand clean fabric with mild solution of soap and water. Rinse thoroughly. Do not use bleach or solvents on fabric. NOTE: To maintain your outdoor furniture we recommend using furniture covers or storing out of the elements when not in use. PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and diagram above. If any part is missing or damaged, do not attempt to assemble the product or return to the place of purchase. Contact our customer service toll free at 1-855-880-7205 for replacement parts or further instructions. Estimated Assembly Time: 5 minutes Tools required for Assembly: No tools required 3
HARDWARE CONTENTS Part Picture Description Quantity M Bolt(M6 X 15) 12 N Bolt (M6 X 45) 16 O Bolt (M6 x 55) 8 P Bolt (M6 X 35) 12 Q Bolt (M6 X 70) 4 R Steel Washer 80 S Nut 28 T Plastic Washer 28 U Bolt Cap 52 V Nut Cap 28 W X Inner Hexagon Wrench Outer Hexagon Wrench 1 1 (M6) 4
PACKAGE CONTENTS Please lay out all parts prior to assembly or installation. Read instructions prior to assembly or installation. Part Picture Description Quantity A Right Armrest 2 B Left Armrest 2 C Back Leg Connecting Tube 2 D Swing Pole 4 E Table Top Support Bracket (small) 1 F Table Top Support Bracket (large) 1 G Left and Right Seat Connecting Bracket 1 H Table Top 1 I Seat & Back 2 J Left Leg 2 K Right Leg 2 L Upper Connecting Tube of Left & Right Leg 4 5
ASSEMBLY INSTRUCTIONS CAUTION: Do not use sharp equipment such as a knife and scissors when removing the protective material, as it may damage the product.. * Place all glider parts and hardware on a soft & clean level surface. Step 1: Attach swing pole (D) to left leg (J) and right leg (K) with M6*45 Bolt (N), plastic washer (T), steel washer (R) and M6 nut (S), as shown above. Do not overtighten the bolts. Step 2: Attach back leg connecting tube (C) to left leg (J) and right leg (K) with M6*15 bolt (M), steel washer (R) as shown above. Do not overtighten the bolts. 6
ASSEMBLY INSTRUCTIONS Step 3: Attach upper collecting tube (L) to left leg (J) and right leg (K) with M6*55 bolts (O), steel washer (R) and M6 nut (S) as shown above. Do not overtighten the bolts. Step 4: Attach left armrest (B) and right armrest (A) to swing pole (D) with M6*45 bolt (N), Plastic washer (T), steel washer (R) and M6 nut (S) as shown above. Do not tighten the bolts. * Repeat from step 1 to step 4 to assemble the other glider chair. 7
ASSEMBLY INSTRUCTIONS Step 5: Place table top (H) on a clean and soft level surface. Then attach table top support brackets (small) (E) and table top support bracket (large) (F) to table top (H)with M6*15 bolt (M) and steel washer (R) as shown above. Do not overtighten the bolts. Step 6: Attach left and right seat connecting bracket (G) to table top support bracket (small) (E) and table top support bracket (large) (F) with M6*35 bolt (P) and steel washer (R) as shown above, do not overtighten bolts. 8
ASSEMBLY INSTRUCTIONS Step 7: Turn the table over, table top support bracket (small)(e), table top support bracket(big) (F), left and right seat connecting bracket (G) and table top(h) will be an integrate part. Insert left and right seat connecting bracket (G) into upper connecting tube of the left & right leg (L). After then, secure with M6*55 bolt(o),steel washer(r),and M6 Nut(S) as below showing. Do not overtighten the bolts. Step 8: Repeat step 7 to attach other side of the table to glider chair as shown above. 9
ASSEMBLY INSTRUCTIONS Step 9: Attach back (I) to left (B) & right armrest (A) with M6*70 bolt (Q), pplastic pad (T), steel washer (R), M6 nuts (S) as shown above, do not tighten the bolts too much. Then attach seat (I) to left (B) & right armrest (A) with M6 X35 bolt (P) and steel washer (R) as shown above. Do not overtighten the bolts. Note: There is only one connecting point between armrest and the back of chair, there are 2 connecting points between seat panel and armrest, as shown above. Step 10: Check connecting points, and adjust if necessary, then, tighten all the bolts and nuts, finnally, cover with bolt cap (U) and nut cap (V). The glider is ready to use as shown, above. 10
WARRANTY 90 DAY WARRANTY This product is covered under a manufacturer s 90 day warranty from date of purchase against defects in materials and workmanship. This warranty does not cover damage due to neglect, abuse or weather related damage. For full warranty disclosure, email us at customerservice@atleisure.com, call toll free at 1-855-880-7205 or send mail to 1040 Boulevard SE Ste. B, Atlanta GA 30312. NOT COVERED UNDER WARRANTY This Warranty excludes the following: general frame rusting; glass breakage; acts of (i.e. wind, fire, or freeze); damage caused by improper assembly, caused by improper assembly, accident, disaster, misuse, abuse, negligence and commercial use; discoloration or fading of the finish or fabric as a result of exposure to the elements. HOW TO FILE A CLAIM If you are within your warranty you must have your receipt and pictures of your information to send to ATLeisure at customerservice@atleisure.com, or send by mail to 1040 Boulevard SE Ste. B, Atlanta GA 30312. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 11
For additional product information, please contact our Customer Service Center at 1-855-880-7205 between 8am- 5pm Eastern Time, Monday through Friday. 2016 Distributed by Menard, Inc., Eau Claire, WI 54703 MADE IN CHINA