Fluid ontrol omponents Index 6100/6200 Series 1 heck valves 691F Series 5 heck valves VH Series 7 heck valves XVH Series 13 Excess flow valves 6500 Series 19 djustable relief valves 6600 Series 21 leed valves 6300 Series 25 Filter elements 1500 Series 27 Toggle valves 6800 Series 31 Gauge valves HOKE Incorporated 405 entura ourt PO ox 4866 (29305) Spartanburg, S 29303 Phone (864) 574-7966 Fax (864) 587-5608 www.hoke.com sales@hoke.com fluid control
6100 & 6200 Series all and Poppet heck Valves Features O-ring seat provides leak-tight shutoff Internal design guides flow around or inside spring, not through coils, when valve is open ll models are tested in production to assure a leak-tight body joint and seat all and poppet designs are available as standard all type provides effective leak-tight closure with minimum flow resistance Poppet models provide large flows with a minimum of chatter and fluctuation Valves are available with various cracking pressures, from 1 3 to 25 psi. 2-piece body permits interchangeability of end connections pplications Prevents reversed flow to protect solenoids, regulators, and pumps Locks pressure in hydraulic cylinders Low pressure inline relief valve Vent valve to purge a system HOKE Incorporated 405 entura ourt PO ox 4866 (29305) Spartanburg, S 29303 Phone (864) 574-7966 Fax (864) 587-5608 www.hoke.com sales@hoke.com Technical ata MXIMUM rass: 3,000 psig @ 70 F (414 R @ 21 ) OPERTING PRESSURE Stainless steel: 6,000 psig @ 70 F (414 R @ 21 ) OPERTING TEMPERTURE una N: -40 F to +200 F (-40 to +93 ) RNGE Viton : -20 F to +350 F (-29 to +177 ) ORIFIE SIZES 0.187 (4.75mm), 0.422 (10.7mm) v FTOR 0.3, 2.4 check valves
6100 & 6200 Series Materials of onstruction LL TYPE POPPET TYPE PRT RSS 316 STINLESS STEEL MONEL 316 STINLESS STEEL ody rass 316 stainless steel Monel 316 stainless steel all/poppet 302 stainless steel 316 stainless steel Monel 316 stainless steel Spring 302 stainless steel 316 stainless steel Monel 316 stainless steel O-ring seat una N Viton Viton Viton /una N* Gasket (body) Mylar Teflon Teflon Teflon /una N* * For poppet check valves with 3 8 and ½ NPT female connections. imensions Inlet Outlet Inlet Outlet E 6100 Series all heck Valves & ONNETIONS HEX HEX E 1 8 NPT female inch 11 16 ¾ 23 8 mm 17 19 60 1 8 NPT male inch 11 16 ¾ 23 8 mm 17 19 60 ¼ NPT female inch ¾ ¾ 2½ mm 19 19 64 ¼ NPT male inch 11 16 ¾ 23 8 mm 17 19 60 ¼ NPT male ¼ Gyrolok inch 11 16 ¾ 2¾ mm 17 19 70 6mm Gyrolok inch 11 16 ¾ 3 mm 17 19 76 ¼ Gyrolok inch 11 16 ¾ 3 mm 17 19 76 3 8 Gyrolok inch 1 ¾ 31 8 mm 25 19 79 E 6200 Series Poppet heck Valves & ONNETIONS HEX HEX E ¼ NPT female inch ¾ ¾ 2½ mm 19 19 64 ¼ NPT male inch 11 16 ¾ 23 8 mm 17 19 60 ¼ Gyrolok inch 11 16 ¾ 3 mm 17 19 76 3 8 Gyrolok inch 1 ¾ 31 8 mm 25 19 79 ½ Gyrolok inch 1¼ 1¼ 3½ mm 32 32 89 2 HOKE Fluid ontrol omponents
6100 & 6200 Series Flow iagrams ir For all models except 3 8 and ½ NPT female 100 3 8 and ½ NPT female models 100 Pressure rop (to tmosphere), PSIG 75 50 25 0 25 psi.p. 10 psi.p. 2 psi.p. 5 10 15 20 25 ir Flow Rate, Standard ubic Feet/Minute Pressure rop (to tmosphere), PSIG 80 60 40 20 14 psi.p. 6 psi.p. 7 psi.p. 3 psi.p. 0 20 40 60 80 100 120 140 160 ir Flow Rate, Standard ubic Feet/Minute 3/8" NPT 1/2" NPT Water For all models except 3 8 and ½ NPT female 50 3 8 and ½ NPT female models 50 40 40 Pressure rop, PSIG 30 20 25 psi.p. Pressure rop, PSIG 30 20 14 psi.p. 10 10 psi.p. 10 6 psi.p. 7psi.P. 3 psi.p. 2 psi.p. 0 2 4 6 8 Water Flow Rate, Liters/Minute 0 10 20 30 40 50 60 70 Water Flow Rate, Liters/Minute How to Order 6100 Series all heck Valves PRT NUMER & ONNETIONS RSS MONEL 316 ST. STEEL ORIFIE 1 8 NPT female 6113F2 6133F2Y 0.187 1 8 NPT male 6113M2 6133M2Y 0.187 ¼ NPT female 6113F4 6133F4Y 0.187 ¼ NPT male 6113M4 6133M4Y 0.187 ¼ Gyrolok 6113G4 6133G4M 6133G4Y 0.187 3 8 Gyrolok 6113G6 6133G6M 6133G6Y 0.187 ¼ NPT male ¼ Gyrolok 6113H4 0.187 6mm Gyrolok 6133G6Y/MM 0.187 3/8" NPT 1/2" NPT 6200 Series Poppet heck Valves PRT NUMER & ONNETIONS 316 ST. STEEL ORIFIE ¼ NPT female 6233F4Y 0.187 ¼ NPT male 6233M4Y 0.187 ¼ Gyrolok 6233G4Y 0.187 3 8 Gyrolok 6233G6Y 0.187 ½ NPT female 6253F8Y 0.422 ½ Gyrolok 6253G8Y 0.422 Other ifferential racking Pressures RKING PRESSURE IGIT 1 3 psi 1 10 psi 5 25 psi 6 ll check valves except 3 8 and ½ female NPT models can be furnished with other that the standard 2 psi cracking pressure. To order, change the fourth digit ( 3 ) of the desired valve part number. Example: 6115G4 is a 6100 Series brass ball check valve with ¼ Gyrolok ends and a 10 psi cracking pressure Gyrolok is a registered trademark of HOKE Incorporated. Viton is a registered trademark of upont ow Elastomers. Monel is a registered trademark of Special Metals orporation. Mylar is a upont Teijin Films registered trademark for its polyester film. Teflon is a registered trademark of the upont ompany. HOKE Fluid ontrol omponents 3
4 HOKE Fluid ontrol omponents
691F Series High Flow Poppet heck Valves Features & enefits Prevents back flow Protects valuable equipment 316 stainless steel components Gyrolok compression ends provide leak-free, reusable connections Recommended for severe service, including NG applications, due to: High v flow rates lowout-proof o-ring design Withstands high opening shocks without damage HOKE Incorporated 405 entura ourt PO ox 4866 (29305) Spartanburg, S 29303 Phone (864) 574-7966 Fax (864) 587-5608 www.hoke.com sales@hoke.com Technical ata OPERTING PRESSURE 5,000 psig @ 70 F (345 R @ 21 ) OPERTING TEMPERTURE RNGE -65 F to +275 F (-54 to +135 ) IFFERENTIL RKING PRESSURES 1 3 psi to 50 psi check valves
691F Series imensions Inlet Outlet Materials of onstruction PRT ody Poppet Seat ring ody gasket Seat o-ring MTERIL 316 stainless steel 316 stainless steel 316 stainless steel Teflon una N Fractional PRT NUMER v OY HEX GYROLOK HEX WRENH 691FxG4Y 0.620 2.72 (69.1mm) 1.000 (25.4mm) 0.562 9 16 691FxG6Y 1.0 2.83 (71.9mm) 1.000 (25.4mm) 0.688 11 16 691FxG8Y 2.1 3.10 (78.7mm) 1.000 (25.4mm) 0.875 7 8 691FxG12Y 6.0 3.75 (95.3mm) 1.625 (41.3mm) 1.125 11 8 691FxG16Y 6.0 3.96 (100.6mm) 1.625 (41.3mm) 1.500 1½ Metric PRT NUMER v OY HEX GYROLOK HEX WRENH 691FxG10YMM 1.2 2.84 (72.1mm) 1.000 (25.4mm) 19.1mm ¾ 691FxG12YMM 1.8 3.13 (79.5mm) 1.000 (25.4mm) 22.2mm 7 8 691FxG18YMM 5.3 3.67 (93.2mm) 1.625 (41.3mm) 28.6mm 11 8 691FxG22YMM 6.0 3.80 (96.5mm) 1.625 (41.3mm) 31.8mm 1¼ 691FxG25YMM 6.0 4.02 (102.1mm) 1.625 (41.3mm) 38.1mm 1½ How to Order FIXE RKING PRESSURE RKING PRESSURE 1 1 3 psi 2 1 psi 4 5 psi 5 10 psi 6 25 psi 7 50 psi 691 F 5 G 8 Y MM ENOTES METRI FITTING OY MTERIL Y 316 stainless steel EN ONNETION SIZE Size in 1 16 increments, or metric when applicable EN ONNETION G Gyrolok Gyrolok is a registered trademark of HOKE Incorporated. Teflon is a registered trademark of the upont ompany. 6 HOKE Fluid ontrol omponents
VH Series heck Valves The VH Series heck Valves are engineered for a competitive price with no compromise of quality and performance to meet the growing requirements of instrumentation valves. The function of this valve series is to maintain system integrity by preventing back flow of a wide variety of fluids over a broad range of pressures. Features & Specifications Quick acting olored band makes the o-ring easy to identify and promotes safety Resilient o-ring seat provides cushioned, quiet closing and zero leakage Floating o-ring design: o-ring is continually cleaned and contaminants do not prevent sealing Various materials of construction can be used with any liquid or gas service Various end connections can be assembled in any system or application Spring-loaded poppet can be mounted in any orientation Full flow with minimal restriction for maximum v rates Virtually maintenance free for maximum dependability Pressures up to 6,000 psig racking pressure range is 0.5 to 20 psi Flow up to 7.4 v maximum More than 100,000 life cycles Technical ata PRESSURE RNGE 0 to 6,000 psig (414 R) TEMPERTURE RNGE -320 F to +900 F (-196 to +482 ) FLOW RNGE 0.32 v to 7.4 v RKING PRESSURE RNGE 0.5 to 20 psi (0.035 to 1.379 R) LEKGE External: zero Internal: Soft seat = zero Teflon seat < 5cc/min Metal seat < 30cc/min ONNETION SIZES 1 8 to 1 ; 6mm to 25mm LIFE YLES In excess of 100,000 cycles HOKE Incorporated 405 entura ourt PO ox 4866 (29305) Spartanburg, S 29303 Phone (864) 574-7966 Fax (864) 587-5608 www.hoke.com sales@hoke.com check valves
VH Series Specifications Operating Temperatures SET MTERIL TEMPERTURE ( F) TEMPERTURE ( ) OLOR N Teflon -320 to +400-196 to +204 Maroon hemraz -20 to +425-29 to +218 Olive Viton -20 to +400-29 to +204 lue Neoprene -40 to +250-40 to +121 Red Ethylene propylene -65 to +300-54 to +149 Purple Fluorosilicone -80 to +350-62 to +177 lack Kalrez -40 to +550-40 to +288 Olive una N -65 to +275-54 to 135 Green Metal -320 to +900-196 to +482 Gold Flow Rates VLVE SIZE 02 04 06 08 10 12 16 v 0.32 0.79 1.71 3.08 3.87 7.38 7.38 Materials of onstructions STNR MTERILS PRT (OTHERS ON REQUEST) 1 ody* (outlet) 316 stainless steel 2 End adapter* (inlet) 316 stainless steel 3 Poppet* 316 stainless steel 4 Spring* 302 stainless steel 5 Part number band nodized aluminum 6 O-ring band nodized aluminum 7 O-ring* Viton 8 Front ferrule* 316 stainless steel 9 Rear ferrule 316 stainless steel 10 Nut 316 stainless steel 11 Spring guide 316 stainless steel 8 5 6 7 4 9 10 2 4 1 11 imensions Gyrolok Tube Fitting, Fractional SIZE E F G 02 0.83 0.20 0.67 1.23 0.09 0.81 0.44 04 0.83 0.20 0.77 1.23 0.19 0.81 0.56 06 1.26 0.20 0.83 1.66 0.30 1.19 0.69 08 1.26 0.20 0.92 1.66 0.42 1.19 0.88 12 2.05 0.50 0.97 3.05 0.66 2.00 1.13 16 2.05 0.50 1.08 3.05 0.66 2.00 1.50 F Hex Gyrolok Tube Fitting, Metric SIZE E F G 04 21.08 5.08 16.89 31.24 2.44 20.62 12.70 06 21.08 5.08 18.49 31.24 3.96 20.62 14.30 08 21.08 5.08 18.08 31.24 5.94 20.62 15.90 10 32.00 5.08 18.80 42.16 8.03 30.15 19.10 12 32.00 5.08 22.38 42.16 10.01 30.15 22.20 14 32.00 5.08 19.99 42.16 12.01 30.15 23.80 16 52.07 12.70 22.38 77.47 12.70 50.80 25.40 18 52.07 12.70 23.58 77.47 15.88 50.80 28.60 22 52.07 12.70 23.58 77.47 16.66 50.80 31.80 25 52.07 12.70 26.38 77.47 16.66 50.80 38.10 E Orifice G Hex 8 HOKE Fluid ontrol omponents
VH Series imensions F Hex Gyrolok Tube dapter, Fractional SIZE E F 02 0.83 0.20 0.63 1.23 0.09 0.81 04 0.83 0.20 0.68 1.23 0.19 0.81 06 1.26 0.20 0.78 1.66 0.28 1.19 08 1.26 0.20 0.97 1.66 0.34 1.19 12 2.05 0.50 1.13 3.05 0.53 2.00 16 2.05 0.50 1.38 3.05 0.53 2.00 E Orifice Gyrolok Tube dapter, Metric SIZE E F 04 21.08 5.08 16.74 31.24 2.39 20.62 06 21.08 5.08 17.32 31.24 4.52 20.62 08 21.08 5.08 19.05 31.24 6.35 20.62 10 32.00 5.08 19.84 42.16 7.62 30.15 12 32.00 5.08 24.51 42.16 9.19 30.15 14 32.00 5.08 24.51 42.16 11.10 30.15 16 52.07 12.70 27.36 77.47 12.70 50.80 18 52.07 12.70 27.86 77.47 13.89 50.80 22 52.07 12.70 29.64 77.47 16.02 50.80 25 52.07 12.70 35.48 77.47 16.02 50.80 E Orifice F Hex Male NPT SIZE E F 02 0.83 0.20 0.40 1.23 0.19 0.81 04 0.83 0.20 0.59 1.23 0.19 0.81 06 1.26 0.20 0.59 1.66 0.39 1.19 08 1.26 0.20 0.77 1.66 0.42 1.19 12 2.05 0.50 0.77 3.05 0.66 2.00 16 2.05 0.50 0.98 3.05 0.66 2.00 F Hex E Orifice Female NPT SIZE INLET OUTLET E F 02 0.83 0.68 0.78 2.29 0.19 0.81 04 0.83 0.91 1.01 2.75 0.19 0.81 06 1.26 0.92 0.97 3.15 0.39 1.19 08 1.26 1.12 1.17 3.55 0.42 1.19 12 2.05 1.40 1.12 4.57 0.66 2.00 16 2.05 1.61 1.33 4.99 0.66 2.00 E Orifice F Hex Male SE SIZE E F 02 0.83 0.20 0.364 1.23 0.19 0.81 04 0.83 0.20 0.427 1.23 0.19 0.81 06 1.26 0.20 0.458 1.66 0.39 1.19 08 1.26 0.20 0.538 1.66 0.42 1.19 12 2.05 0.50 0.699 3.05 0.66 2.00 16 2.05 0.50 0.729 3.05 0.66 2.00 F Hex E Orifice Female SE SIZE INLET OUTLET E F 02 0.83 0.689 0.75 2.27 0.19 0.81 04 0.83 0.769 0.83 2.43 0.19 0.81 06 1.26 0.833 0.89 2.98 0.39 1.19 08 1.26 0.913 0.97 3.55 0.42 1.19 12 2.05 1.297 1.08 4.43 0.66 2.00 16 2.05 1.297 1.08 4.43 0.66 2.00 HOKE Fluid ontrol omponents 9
VH Series imensions Male ritish Parallel Pipe SIZE E F 02 0.83 0.20 0.374 1.23 0.19 0.81 04 0.83 0.20 0.551 1.23 0.19 0.81 06 1.26 0.20 0.570 1.66 0.39 1.19 08 1.26 0.20 0.669 1.66 0.42 1.19 12 2.05 0.50 0.747 3.05 0.66 2.00 16 2.05 0.50 0.827 3.05 0.66 2.00 E Orifice F Hex Male ritish Tapered Pipe SIZE E F 02 0.83 0.20 0.40 1.23 0.19 0.81 04 0.83 0.20 0.60 1.23 0.19 0.81 06 1.26 0.20 0.61 1.66 0.39 1.19 08 1.26 0.20 0.81 1.66 0.42 1.19 12 2.05 0.50 0.86 3.05 0.66 2.00 16 2.05 0.50 0.02 3.05 0.66 2.00 E Orifice F Hex Female ritish Parallel Pipe SIZE INLET OUTLET E F 02 0.83 0.629 0.77 2.23 0.19 0.81 04 0.83 0.839 0.99 2.66 0.19 0.81 06 1.26 0.863 0.98 3.10 0.39 1.19 08 1.26 0.993 1.09 3.34 0.42 1.19 12 2.05 1.257 1.03 4.34 0.66 2.00 16 2.05 1.367 1.16 4.58 0.66 2.00 F Hex E Orifice Female ritish Tapered Pipe SIZE INLET OUTLET E F 02 0.83 0.73 0.75 2.31 0.19 0.81 04 0.83 0.98 1.00 2.81 0.19 0.81 06 1.26 0.99 1.05 3.30 0.39 1.19 08 1.26 1.25 1.32 3.83 0.42 1.19 12 2.05 1.49 1.24 4.78 0.66 2.00 16 2.05 1.73 1.48 5.26 0.66 2.00 F Hex E Orifice 10 HOKE Fluid ontrol omponents
VH Series How to Order VH Y 04 G 04 M 32 010 O H OY MTERIL rass arpenter 20 I Inconel O 254 SMO RES M Monel H Hastelloy 276 Y 316 stainless steel T Titanium INLET SIZE 02 1 8 14 14mm 04 4mm, ¼ 16 16mm, 1 06 6mm, 3 8 18 18mm 08 8mm, ½ 22 22mm 10 10mm 25 25mm 12 12mm, ¾ INLET TYPE G Gyrolok tube fitting, per HOKE Gyrolok tube adapter, per HOKE Z Metric Gyrolok tube fitting, per HOKE W Metric Gyrolok tube adapter, per HOKE S Male SE, per J514 R Female SE, per J1926 L Male ritish parallel pipe, per ISO 1179 K Female ritish parallel pipe, per ISO 1179 M Male NPT, per NSI/SME 1.20.1 F Female NPT, per NSI/SME 1.20.1 Q Male ritish tapered pipe ISO 7/1 P Female ritish tapered pipe ISO 7/1 OUTLET SIZE 02 1 8 14 14mm 04 4mm, ¼ 16 16mm, 1 06 6mm, 3 8 18 18mm 08 8mm, ½ 22 22mm 10 10mm 25 25mm 12 12mm, ¾ LENING OPTIONS O Standard ryogenic cleaning Industrial cleaning NE compliant N OPTIONS luminum bands (standard) Y Stainless steel bands RKING PRESSURE 005 0.5 psi (0.035 R) 010 1.0 psi (0.069 R) 030 3.0 psi (0.206 R) 050 5.0 psi (0.344 R) 100 10 psi (0.688 R) 200 20 psi (1.379 R) (other available on request) SEL MTERILS 20 Teflon 25 hemraz 32 Viton 40 Teflon (cryogenic service) 53 Neoprene 62 Ethylene propylene 64 Fluorosilicone 65 Kalrez 77 una N 00 Metal (high temperature service) OUTLET TYPE G Gyrolok tube fitting, per HOKE Gyrolok tube adapter, per HOKE Z Metric Gyrolok tube fitting, per HOKE W Metric Gyrolok tube adapter, per HOKE S Male SE, per J514 R Female SE, per J1926 L Male ritish parallel pipe, per ISO 1179 K Female ritish parallel pipe, per ISO 1179 M Male NPT, per NSI/SME 1.20.1 F Female NPT, per NSI/SME 1.20.1 Q Male ritish tapered pipe ISO 7/1 P Female ritish tapered pipe ISO 7/1 Please consult HOKE Incorporated or your local distributor for information on special connections, o-rings, operating pressures and temperature ranges. Gyrolok is a registered trademark of HOKE Incorporated. arpenter is a registered trademark of arpenter Technology orporation. Inconel and Monel are registered trademarks of Special Metals orporation. Hastelloy is a registered trademark of Haynes International, Inc. Teflon is a registered trademarks of the upont ompany. hemraz is a registered trademark of Greene, Tweed & o. Kalrez and Viton are registered trademarks of upont ow Elastomers. For Your Safety It is solely the responsibility of the system designer and user to select products suitable for their specific application requirements and to ensure proper installation, operation, and maintenance of these products. Material compatibility, product ratings and application details should be considered in the selection. Improper selection or use of products described herein can cause personal injury or property damage. HOKE Fluid ontrol omponents 11
12 HOKE Fluid ontrol omponents
XVH Series Excess Flow Valve XVH Series Excess Flow Valves are safety devices, flow switches, that automatically close when a flow spike occurs, preventing uncontrolled release of system fluid. The XVH Series are available in automatic and manual reset versions, depending on your requirements. utomatic reset XVH Series have an anti-clog wire which increases reliability by preventing a build up of system fluid in the bleed port. The XVH Series are high pressure (0 to 6,000 psig), high performance, quick acting, zero leakage, low maintenance excess flow valves that will help provide a reliable and safe working environment. Lower cost Versatile Reliable Safety Flexible Features utomatic reset The bleed vent allows the valve to automatically reset Manual reset Zero leakage: the valve must be manually reset olored ring bands Visual identification of valve type, trip range and seal material O-ring, Teflon or metal seat an be used with any liquid or gas service Various body materials an be used with any liquid or gas service Various end connections an be assembled in any system or application Spring-loaded poppet an be mounted in any orientation nti-clog wire Prevents clogging of bleed port Technical ata OPERTING PRESSURE Zero to 6,000 psig (414 R) LEKGE RTE External: zero leak Internal soft seat: zero leak Teflon seat: 5cc per minute maximum FLOW/TRIP POINT RNGES Low, medium, and high (see graphs, page 29) HOKE Incorporated 405 entura ourt PO ox 4866 (29305) Spartanburg, S 29303 Phone (864) 574-7966 Fax (864) 587-5608 www.hoke.com sales@hoke.com excess flow valves
XVH Series How It Works Excess Flow Valves are designed to limit flow of fluid to a predetermined rate. When flow reaches a predetermined rate the poppet will close, limiting or stopping flow. When pressure is equalized across the valve, the poppet will reset to the open position. Open Position Tripped Position The spring holds the poppet in the open position during normal flow. When flow increases to the predetermined rate or trip point, the poppet will close. Materials of onstruction 8 3 4 5 6 9 10 1 7 2 utomatic Reset The poppet will remain in the tripped position until system pressure becomes equal across the poppet. The bleed orifice in the poppet will allow the pressure to slowly equalize across the valve if the downstream line is closed or repaired. When the pressure becomes equal, the spring will then reset the poppet to the open position, allowing normal flow. Manual Reset The poppet will remain in the tripped position with zero leakage and zero flow until pressure is manually equalized across the poppet. When the pressure becomes equal, the spring will then reset the poppet to the open position, allowing normal flow. STNR MTERIL PRT (OTHERS VILLE ON REQUEST) 1 ody* (outlet) 316 stainless steel 2 End adapter* (inlet) 316 stainless steel 3 Poppet* 316 stainless steel 4 Spring* 302 stainless steel Inconel with 20, 25, 40, 65, and 00 seals 5 O-ring band nodized aluminum 6 Part number band nodized aluminum 7 nti-clog wire* 302 stainless steel 8 Front ferrule* 316 stainless steel 9 Rear ferrule 316 stainless steel 10 Nut 316 stainless steel * Wetted component Operating Temperatures Soft Seal, Manual Reset Valve TEMPERTURE O-RING OE O-RING MTERIL OLOR F 20 Teflon Maroon -320 to +400-196 to +204 25 hemraz Olive -20 to +425-29 to +218 32 Viton lue -20 to +400-29 to +204 40 Teflon Maroon -320 to +500-196 to +260 53 Neoprene Red -40 to +250-40 to +121 62 Ethylene propylene Purple -65 to +300-54 to +149 64 Fluorosilicone lack -80 to +350-62 to +177 65 Kalrez Olive -40 to +550-40 to +288 77 una N Green -65 to +275-54 to +135 Metal Seal, utomatic Reset Valve TEMPERTURE O-RING OE O-RING MTERIL OLOR F 00 Gold -320 to +900-196 to +482 14 HOKE Fluid ontrol omponents
XVH Series Flow Rates Water Flow Using the graph in Figure 1, look up your desired normal flow rate (including normal surges) on the X axis. Read vertically on the graph to the v line and then left on the graph from the v line to the pressure drop. Then select a valve and trip range higher than normal expected flow. For example: With a normal flow rate of 1 GPM, a ¼ valve will have a pressure drop of approximately 6.5 psi. Selecting a ¼ valve with a medium flow/trip option, the valve will close when the flow reaches 1.5 GPM and a pressure drop of approximately 15 psi. TRIP POINTS 100-4 HIGH TRIP -6 HIGH TRIP -8 HIGH TRIP PRESSURE ROP, PSI XVH-4 XVH-6-8 ME TRIP -6 ME TRIP -4 ME TRIP 10-8 LOW TRIP -6 LOW TRIP -4 LOW TRIP 1.1 1 10 100 WTER FLOW RTE, GPMXVH-8 Figure 1 ir Flow Using the graphs (Figure 2, 3 or 4), find the intersection of your normal flow rate (including normal surges) and the inlet pressure of the excess flow valve. From there, move to the right on the graph and select a valve with a trip/flow range greater than your normal flow. For example: reading Figure 2, if normal flow is 20 scfm and the inlet pressure is 200 psig, you would select a ¼ valve with a medium flow/trip range. XVH-4: 04 (INH), 06& 08(METRI) 3000 INLET PRESSURE, PSIG 1000 500 LOW TRIP RNGE MEIUM TRIP RNGE HIGH TRIP RNGE 100 10 100 1000 IR FLOW RTE, SFM Figure 2 HOKE Fluid ontrol omponents 15
XVH Series XVH-6: 06 (INH), 10& 12(METRI) 3000 INLET PRESSURE, PSIG 1000 500 LOW TRIP RNGE MEIUM TRIP RNGE HIGH TRIP RNGE 100 10 100 1000 IR FLOW RTE, SFM Figure 3 XVH-8: 08 (INH), 14(METRI) 3000 INLET PRESSURE, PSIG 1000 500 LOW TRIP RNGE MEIUM TRIP RNGE HIGH TRIP RNGE 16 100 10 HOKE Fluid ontrol omponents 100 1000 IR FLOW RTE, SFM Figure 4
XVH Series How to Order XVH Y 08 M 08 G 00 100 O H OY MTERIL Y 316 stainless steel (standard) rass I Inconel M Monel arpenter 20 O 254 SMO RES H Hastelloy T Titanium INLET SIZE 04 ¼ (standard) 06 6mm, 3 8 (standard) 08 8mm, ½ (standard) 10 10mm 12 12mm 14 14mm INLET STYLE G Gyrolok tube fitting (standard) Gyrolok tube adapter (standard) Z Gyrolok tube fitting, metric W Gyrolok tube adapter, metric S Male SE R Female SE L Male ritish parallel pipe K Female ritish parallel pipe M Male NPT (standard) F Female NPT (standard) Q Male ritish tapered pipe P Female ritish tapered pipe OUTLET SIZE 04 ¼ (standard) 06 6mm, 3 8 (standard) 08 8mm, ½ (standard) 10 10mm 12 12mm 14 14mm LENING OPTIONS O Standard Oxygen cleaning ryogenic service NE compliant N OPTIONS Standard Y orrosive atmosphere TRIP POINT Standard Flow 100 Low 200 Medium 300 High (standard) Low Flow 010 Low 020 Medium 030 High O-RING MTERIL Manual Reset 20 Teflon 25 hemraz 32 Viton 40 Teflon (cryogenic service) 53 Neoprene 62 Ethylene propylene 64 Fluorosilicone 65 Kalrez 77 una N (not for oxygen service) utomatic Reset 00 No o-ring (metal-to-metal seat) OUTLET STYLE G Gyrolok tube fitting (standard) Gyrolok tube adapter (standard) Z Gyrolok tube fitting, metric W Gyrolok tube adapter, metric S Male SE R Female SE L Male ritish parallel pipe K Female ritish parallel pipe M Male NPT* (standard) F Female NPT* (standard) Q Male ritish tapered pipe P Female ritish tapered pipe Note: Inlet and outlet fittings can be the same or mixed sizes and styles. Gyrolok is a registered trademark of HOKE Incorporated. Teflon is a registered trademark of the upont ompany. Inconel and Monel are registered trademarks of Special Metals orporation. hemraz is a registered trademark of Greene, Tweed & o. Kalrez and Viton are registered trademarks of upont ow Elastomers. arpenter is a registered trademark of arpenter Technology orporation. Hastelloy is a registered trademark of Haynes International, Inc. HOKE Fluid ontrol omponents 17
18 HOKE Fluid ontrol omponents
6500 Series djustable Relief Valves Features Seat seals may be replaced in the field if necessary Valve has a compact forged body with large wrench pads for easy installation Friction between body and poppet is reduced by a Teflon band which permits easy movement of the poppet when opening or resealing the valve Three pressure ranges: 20 75 psig, 75 350 psig, 350 1,500 psig rass or 316 stainless steel construction Relief settings may be adjusted externally by opening or closing the screw and lock-nut on top of the bonnet Models are furnished in angle pattern with ¼ NPT male inlet by ¼ NPT female outlet connections Technical ata HOKE Incorporated 405 entura ourt PO ox 4866 (29305) Spartanburg, S 29303 Phone (864) 574-7966 Fax (864) 587-5608 www.hoke.com sales@hoke.com MXIMUM 3,000 psig @ 70 F (211 kg/cm² @ 21 ) OPERTING PRESSURE OPERTING TEMPERTURE RNGE rass: -20 F to +200 F (-29 to +93 ) Stainless steel: -20 F to +350 F (-29 to +177 ) ORIFIE 0.250 (6.35mm) v FTOR 0.1 full open relief valves
6500 Series Materials of onstruction PRT RSS 316 STINLESS STEEL 1 ody rass 316 stainless steel 2 onnet rass 303 stainless steel 3 Set screw arbon steel 303 stainless steel 4 O-ring (upper) una N Viton 5 O-ring (lower) Teflon / una N* Teflon / Viton ** 6 ompression spring Music wire 17-7 PH stainless steel 7 Seat holder rass (TFE-coated) 316 stainless steel For models 6528L4 and 6548L4Y. * For models 6512L4 and 6514L4 ** For models 6532L4Y and 6532L4Y 3 2 4 6 imensions PRESSURE RNGE E 20 75 psi inch 313 16 1½ mm 97 38 75 350 psi inch 313 16 1½ mm 97 38 350 1,500 psi inch 313 16 1½ mm 97 38 7 1 Outlet 5 Inlet E How to Order Pressure Range P ORER Y MOEL NUMER PRESSURE RNGE RSS 316 STINLESS STEEL 20 75 psi 6512L4 6532L4Y 75 350 psi 6514L4 6534L4Y 350 1,500 psi 6528L4 6548L4Y Teflon is a registered trademark of the upont ompany. Viton is a registered trademark of upont ow Elastomers. 20 HOKE Fluid ontrol omponents
6600 Series leed Valves HOKE 6600 Series bleed valves allow for quick, easy manual bleed off of system pressure. These valves come in a variety of configurations, including straight, elbow, union, and tee. Features ompact installation 316 stainless steel construction Straight, union, elbow or tee flow configurations Integral tube ends enefits Safe Reliable Gyrolok fitting connections eliminate pipe thread leak paths Typical pplications ir, hydraulic systems, or natural gas Venting or purging of liquids and gases For use on instrument manifolds HOKE Incorporated 405 entura ourt PO ox 4866 (29305) Spartanburg, S 29303 Phone (864) 574-7966 Fax (864) 587-5608 www.hoke.com sales@hoke.com Technical ata MXIMUM OPERTING PRESSURE 6,000 psig @ 70 F (414 R @ 21 ) OPERTING TEMPERTURE RNGE -40 F to +600 F (-40 to +316 ) EN ONNETIONS ¼, 3 8, ½ Gyrolok VERGE OPERTING TORQUE 40 in-lbs MXIMUM OPERTING PRESSURE Operating Instructions Valve is operated by turning the bleed port nut with a wrench. Use appropriate back-up wrench to hold body, while turning bleed nut. s bleed nut is turned, pressure forces ball off seat. Pressure is vented through a hole drilled in the nut, angled back toward the body of the valve. Make sure flow is directed away from user. Those using the valves should wear protective clothing, especially goggles. No attempt should be made to repair or dismantle the valve. bleed valves
6600 Series imensions ' ' Wrench Flat Wrench Flat P P 6610 Series 6610001 6610 Series: Straight Valve PRT NUMER P THRE NPT OPEN HEX WRENH FLT 6610M2Y 1 8 13 8 (35mm) 5 8 ½ 6610M4Y ¼ 117 32 (39mm) 5 8 9 16 6610M6Y 3 8 119 32 (40mm) 5 8 11 16 6610M8Y ½ 113 16 (46mm) 5 8 7 8 6610001 ¼ 117 32 (39mm) 5 8 9 16 M M1 Wrench Flat 6660G4Y 1 6660 Series: Elbow Valve PRT NUMER T TUE O.. HEX HEX WRENH FLT M M 6660G4Y ¼ 125 32 (45mm) 21 64 (52mm) 9 16 5 8 7 16 13 64 (27mm) 23 32 (18mm) 1 ' UTION 6670G6Y M ' Wrench Flat T 6670 Series: Union Valve PRT NUMER T TUE O.. HEX HEX WRENH FLT M 6670G4Y ¼ 23 32 (53mm) 123 64 (35mm) 9 16 5 8 7 16 15 64 (27mm) 6670G6Y 3 8 221 64 (59mm) 17 16 (37mm) 11 16 5 8 ½ 13 32 (28mm) 6670G8Y ½ 257 64 (73mm) 121 32 (42mm) 7 8 5 8 11 16 17 32 (31mm) imensions for reference only and are subject to change without notice. 22 HOKE Fluid ontrol omponents
6600 Series imensions ' UTION 6680G6Y M' Wrench Flat ' M T 6680 Series: Tee Valve PRT NUMER T TUE O.. HEX HEX WRENH FLT M M 6680G4Y ¼ 29 64 (54mm) 25 64 (53mm) 9 16 5 8 7 16 11 16 (27mm) 11 64 (27mm) 6680G6Y 3 8 223 64 (60mm) 213 64 (52mm) 11 16 5 8 ½ 23 16 (56mm) 11 64 (27mm) 6680G8Y ½ 257 64 (73mm) 213 64 (68mm) 7 8 5 8 11 16 129 64 (37mm) 17 32 (31mm) 6631 Series irected leed Valves HOKE s 6631 leed Valve allows the user to direct the bled fluid as desired. The valve can be ordered with a 1½ (38mm) press fit handle by adding an H suffix to the valve part number (e.g., 6631H4YH). To operate, simply turn the 7 16 nut with a wrench or the optional loose fit stainless steel bar handle, part number 96706 103. Please consult your local distributor for details.t aution: If the vented fluids are not going to be contained, the vent tube must be positioned at installation so that it is directed away from the operating personnel. Technical ata MXIMUM OPERTING PRESSURE 5,000 psig @ 70 F (345 R @ 21 ) OPERTING TEMPERTURE RNGE -20 F to +425 F (-29 to +218 ) ORIFIE 0.125 (3.2mm) enefits Safety O-ring packaging prevents leakage through stem threads Reliability ll valves are tested for bubble-tight leakage Typical pplications Venting or purging of liquids and gases For use on gauge valves 7 /16" Hex imension hart PRT NUMER INLET E 6631H4Y ¼ ¾ (19mm) 2 (51mm) 11 16 (17mm) 11 8 (29mm) 6631H84Y ½ 29 32 (23mm) 21 8 (54mm) 11 16 (17mm) 11 8 (29mm) Materials of onstruction PRT MTERIL 1 ody 316 stainless steel 2 Stem 316 stainless steel 3 Vent tube 316 stainless steel 4 O-ring Fluoroelastomer 1 4 2 0.125" diameter orifice E 3 ¼" tube size adapter Gyrolok is a registered trademark of HOKE Incorporated. HOKE Fluid ontrol omponents 23
24 HOKE Fluid ontrol omponents
6300 Series Micron Filters Features hoice of in-line, removable, or bypass filter models NPT female and Gyrolok tube fitting connections Variety of micron filtering ranges from 2 to 55µ Filter elements are available in 316 stainless steel Filter elements are easily replaced ypass models permit purging and sampling of process fluid odies come in brass and 316 stainless steel pplications Trap foreign particles Protect sensitive equipment System purging Pressure damper Technical ata MXIMUM OPERTING PRESSURE OPERTING TEMPERTURE RNGE MIRON RNGE 2 to 55µ v FTOR RNGE 0.006 to 0.42 rass: 3,000 psig @ 70 F (211 kg/cm² @ 21 ) Stainless steel: 5,000 psig @ 70 F (352 kg/cm² @ 21 ) -60 F to +450 F (-51 to +232 ) HOKE Incorporated 405 entura ourt PO ox 4866 (29305) Spartanburg, S 29303 Phone (864) 574-7966 Fax (864) 587-5608 www.hoke.com sales@hoke.com filters
6300 Series iagrams & Flow urves Water 3.0 ir 800 Water Flow (GPM) 2.5 2.0 1.5 1.0 0.5 Element No. 80410 1 80410 2 80410 3 80410 4 80410 5 Filtering Range Microns 2 5µ 5 9µ 10 15µ 20 30µ 40 55µ Material 316SS 316SS 316SS 316SS 316SS Filtering Element No. 80410 5 Filtering Element No. 80410 4 Filtering Element No. 80410 3 Filtering Element No.80410 2 Filtering Element No.80410 1 ir Flow (SFH) 700 600 500 400 300 200 Element No. 80410 1 80410 2 80410 3 80410 4 80410 5 Filtering Range Microns 2 5µ 5 9µ 10 15µ 20 30µ 40 55µ Material 316SS 316SS 316SS 316SS 316SS Filtering Element No. 80410 5 Filtering Element No. 80410 4 Filtering Element No. 80410 3 Filtering Element No. 80410 2 0 1 2 3 4 5 6 7 8 9 10 100 Filtering Element No.80410 1 Pressure rop to tmosphere (PSI) 0 1 2 3 4 5 6 7 8 9 10 Pressure rop to tmosphere (PSI) 17.5 3500 15.0 Element No. Filtering Range Microns Material 91442 1 10 15µ 316SS 3000 Element No. Filtering Range Microns Material 91442 1 10 15µ 316SS 12.5 2500 Water Flow (GPM) 10.0 7.5 ir Flow (SFH) 2000 1500 5.0 1000 2.5 Filtering Element No. 91442 1 500 Filtering Element No.91442 1 0 1 2 3 4 5 Pressure rop to tmosphere (PSI) 6 7 8 9 10 How to Order Select and specify filter by part number, according to desired connections and materials of construction. e sure to add the identifying digit of the desired filter element to the filter part number from the chart below. To order a 316 stainless steel in-line type, 1 8 NPT female filter with an element range of 5 to 9µ, add 2 (e.g., 6312F2Y). To order a filter without a filter element, insert the number 0 in the model number desired (e.g., 6310F2Y). 0 1 2 3 4 5 Pressure rop to tmosphere (PSI) 6 7 8 9 10 Outlet Outlet Inlet Inlet Outlet Inlet Outlet 6310 Series: In-line Filters & ONNETIONS RSS 316 STINLESS STEEL 1 8 NPT female 631xF2 631xF2Y ¼ NPT female 631xF4 631xF4Y 1 8 Gyrolok 631xG2Y 6320 Series: Removable Filters & ONNETIONS RSS 316 STINLESS STEEL 1 8 Gyrolok 632xG2 632xG2Y ¼ NPT female 632xF4 632xF4Y ¼ Gyrolok 632xG4 632xG4Y 6330 Series: ypass Filters & ONNETIONS 316 STINLESS STEEL ¼ NPT female 633xF4Y 1 8 Gyrolok 633xG2Y Gyrolok is a registered trademark of HOKE Incorporated. 26 HOKE Fluid ontrol omponents 316 Stainless Steel Elements FOR 1 8 & ¼ FOR 3 8 & ½ IENTIFYING MIRON RNGE SIZE HOUSINGS SIZE HOUSINGS IGIT v FTOR 2 to 5µ 80410 1 80409 1* 1 0.006 5 to 9µ 80410 2 80409 2* 2 0.055 10 to 15µ 80410 3 80409 3 91442 1 3 0.33 20 to 30µ 80410 4 80409 4* 4 0.39 40 to 55µ 80410 5 80409 5* 5 0.42 0.5µ 80410 6 6 100µ 80410 7 7 * For use with 6330 Series ypass-type housing
1500 Series Forged ody Toggle Valves Featuring a simple, reliable design concept, this low-maintenance valve is well suited for a wide variety of applications. The toggle handle provides easy on-off operation and visual indication of flow. enefits Safety Handle gives visual indication of stem position Instant control Toggle handle provides instant on-off control Vacuum service Elastomeric seals provide leak-tight sealing under positive pressure and vacuum conditions Reliability ll valves are tested for bubble-tight leakage at both seat and packing Installation variety hoose from a broad selection of male NPT, female NPT and HOKE Gyrolok tube fitting connections Handle options olor-coded handles are available for identifying system fluids Panel mounting Panel mounting is standard on all models Typical pplications hromatographs and mass spectrometers Manometer shutoff valves ir lines Instrument panels Technical ata HOKE Incorporated 405 entura ourt PO ox 4866 (29305) Spartanburg, S 29303 Phone (864) 574-7966 Fax (864) 587-5608 www.hoke.com sales@hoke.com MXIMUM OPERTING PRESSURE 0.125 orifice: 200 psig @ 70 F (1,380 kpa @ 21 ) 0.219 orifice: 100 psig @ 70 F (690 kpa @ 21 ) OPERTING -20 F to +300 F (-29 to +149 ) TEMPERTURE RNGE ORIFIE SIZES 0.125 to 0.219 (3.2 to 5.6mm) v FTORS 0.23 to 0.60 EN ONNETION 1 8 to ¼ Gyrolok, 1 8 to 3 8 NPT toggle valves
1500 Series Materials of onstruction PRT RSS VLVES 316 STINLESS STEEL VLVES ody rass 316 stainless steel Stem rass 316 stainless steel Stem packing Viton o-ring Viton o-ring Stem disc Viton Viton Spring 18-8 stainless steel 18-8 stainless steel onnet rass 316 stainless steel Handle, molded Nylon, black Nylon, black Panel mounting nut Nickel-plated brass Nickel-plated brass onnet Panel Mounting Nut Handle Stem Stem Packing Stem isc Spring ody imensions E 1500 Series Globe Pattern H 1 H 1500 Series: Globe Pattern INLET N OUTLET (LOSE) (OPEN) E H H¹ 1 8 Gyrolok inch 147 64 241 64 23 8 25 64 ¾ mm 44 67 60 10 19 1 8 male NPT inch 147 64 241 64 1¾ 25 64 ¾ mm 44 67 44 10 19 1 8 female NPT inch 147 64 241 64 1¾ 25 64 ¾ mm 44 67 44 10 19 ¼ Gyrolok inch 147 64 241 64 23 8 25 64 ¾ mm 44 67 60 10 19 ¼ male NPT inch 147 64 241 64 1¾ 25 64 ¾ mm 44 67 44 10 19 ¼ female NPT inch 157 64 251 64 17 8 31 64 15 16 mm 48 71 48 12 24 3 8 male NPT inch 157 64 251 64 17 8 31 64 15 16 mm 48 71 48 12 24 imensions for reference only, subject to change. H 1 H 1500 Series: ngle Pattern INLET N OUTLET (LOSE) (OPEN) E H H¹ 1 8 Gyrolok inch 143 64 237 64 17 16 17 64 11 16 mm 42 66 36 28 17 1 8 male NPT inch 12 3 32 25 8 117 6 4 7 8 ¾ mm 44 67 32 22 19 1 8 female NPT inch 12 3 32 25 8 117 6 4 7 8 ¾ mm 44 67 32 22 19 ¼ Gyrolok inch 123 32 25 8 119 32 113 64 ¾ mm 44 67 40 31 19 ¼ male NPT inch 12 3 32 25 8 117 6 4 7 8 ¾ mm 44 67 32 22 19 imensions for reference only, subject to change. E 1500 Series ngle Pattern Panel Mounting Panel hole: for ¼ female and 3 8 male models (0.219 orifice) = 33 64 (13.1mm) diameter all other models (0.125 orifice) = 29 64 (11.5mm) diameter Panel thickness = 3 16 (4.7mm) maximum 28 HOKE Fluid ontrol omponents
1500 Series How to Order 1500 Series: Globe Pattern ORER Y PRT NUMER EN ONNETIONS RSS 316 STINLESS STEEL ORIFIE v 1 8 Gyrolok 1513G2 1513G2Y 0.125 0.23 1 8 male NPT 1513M2 1513M2Y 0.125 0.23 1 8 female NPT 1513F2 1513F2Y 0.125 0.23 ¼ Gyrolok 1513G4 1513G4Y 0.125 0.23 ¼ male NPT 1513M4 1513M4Y 0.125 0.23 ¼ female NPT 1533F4 0.219 0.60 3 8 male NPT 1533M6 0.219 0.60 1513G4 1500 Series: ngle Pattern ORER Y PRT NUMER EN ONNETIONS RSS ORIFIE v 1 8 Gyrolok 1523G2 0.125 0.31 1 8 male NPT 1523M2 0.125 0.31 1 8 female NPT 1523F2 0.125 0.31 ¼ Gyrolok 1523G4 0.125 0.31 ¼ male NPT 1523M4 0.125 0.31 Handle Options OPTION ESRIPTION PRT NUMER Handle positioning kit Secures handle against rotation; permits placement 1500K5 of handle in any position on a panel face. Flip-shut pin Pin prevents handle from being left in the open position. 59 544 olored handles Standard handle is black Red handle 95626 031 Yellow handle 95626 032 lue handle 95626 033 1523F2 Handle Positioning Kit #1500K5 Handle with Flip-shut Pin #59 544 Spare Parts Spare parts and repair kits are available for all toggle valves. Please contact your distributor for specific information. leaning and Testing When ordering, please specify if oxygen cleaning or helium leak testing is required. dditional Sizes dditional sizes and options are available on special request. Please consult your local HOKE distributor. Gyrolok is a registered trademark of HOKE Incorporated. Viton is a registered trademark of upont ow Elastomers. HOKE Fluid ontrol omponents 29
30 HOKE Fluid ontrol omponents
6800 Series Gauge Valves Features orrosion-resistant bar stock 316 stainless steel bodies Packing below stem threads prevents contamination and wash away of thread lubricants to assure long valve life Hardened 17-4 PH 2-piece, non-rotating stem point minimizes seat galling and provides an excellent metal-to-metal seat for positive shutoff Low profile bonnet assembly and large diameter stem reduces damage to bonnet and stem assembly Roll pin locks bonnet in the valve body to prevent accidental removal hoice of 53 8 long body for standard process use or 73 8 body for insulated piping applications Three outlets meet individual gauge requirements Polyethylene cap protects stem and bonnet from external damage Rugged large handle provides easy grip and control ll models are stamped with maximum operating pressures on valve body High temperature packing is available on special order Technical ata MXIMUM OPERTING PRESSURE 6,000 psig @ -65 to +200 F (422 kg/cm² @ -54 to +93 ) 3,000 psig @ +450 F (211 kg/cm² @ +232 ) OPERTING TEMPERTURE RNGE -65 F to +450 F (-54 to +232 ) ORIFIE HOKE Incorporated 405 entura ourt PO ox 4866 (29305) Spartanburg, S 29303 Phone (864) 574-7966 Fax (864) 587-5608 www.hoke.com sales@hoke.com 6801L8Y: 0.156 (3.96mm) ll others: 0.187 (4.75mm) gauge valves
6800 Series Materials of onstruction 4 2 3 5 6 1 9 11 8 7 10 PRT 316 STINLESS STEEL MOELS 1 ody 316 stainless steel 2 Housing 316 stainless steel 3 Handle 303 stainless steel 4 Hex nut 18-8 stainless steel 5 Packing nut XM-28 stainless steel 6 Lock nut 316 stainless steel 7 Packing* yna-pak 8 Stem 316 stainless steel 9 Retaining ring 316 stainless steel 10 isc 17-7 PH stainless steel 11 Stem point 17-4 PH stainless steel * Model 6801L8Y uses a single-piece molded Teflon packing system. F PSIG KG/M 2 6000 422 E Pressure vs. Temperature yna-pak Packing TFE Packing (6801L8Y only) imensions MOEL NUMER E F 6801L8Y inch 1¼ 217 32 1 9 16 1¾ 3¼ mm 32 64 25 14 44 83 6802L8Y inch 25 8 3 25 32 27 32 2¼ 53 8 mm 67 75 55 21 57 136 6803L128Y inch 25 8 3 25 32 27 32 2¼ 53 8 mm 67 75 55 21 57 136 6805L128Y inch 25 8 3 45 32 27 32 2¼ 73 8 mm 67 75 106 21 57 188 Recommended Working Pressure 5000 352 4000 281 3000 211 2000 141 1000 70 How to Order ONNETIONS ORER Y PRT NUMER OY LENGTH INLET OUTLET 316 STINLESS STEEL INH MM ½ NPT male ½ NPT female 6801L8Y* 3¼ 83 ½ NPT male ½ NPT female (3 ) 6802L8Y 53 8 136 ½ NPT female ½ NPT female (3 ) 6802F8Y 53 8 136 ¾ NPT male ½ NPT female (3 ) 6803L128Y 53 8 136 ¾ NPT male ½ NPT female (3 ) 6805L128Y 73 8 188 * Furnished with bleed plug drilled in body Model 6801L8Y uses a single-piece molded Teflon packing system F -65-54 0-18 100 38 200 93 300 149 Temperature 400 204 500 260 600 316 yna-pak is a registered trademark of HOKE Incorporated. Teflon is a registered trademark of the upont ompany. 32 HOKE Fluid ontrol omponents
Instrumentation Technologies IROR Instrumentation Technologies 405 entura ourt Spartanburg, S 29303 Tel (864) 574-7966 Fax (864) 587-5608 ircle Seal ontrols, Inc. 2301 Wardlow ircle orona, 92880 Tel (951) 270-6200 Fax (951) 270-6201 www.circle-seal.com GO Regulator 405 entura ourt Spartanburg, S 29303 Tel (864) 574-7966 Fax (864) 587-5608 www.goreg.com Panels Plus 1901 Lynx Place Ontario, 91761 Tel (909) 923-3770 Fax (909) 923-2550 www.circor-panelsplus.com IROR Instrumentation, Ltd. 1-3 ouverie Road Harrow Middlesex, H1 4H UK Tel +44 (0) 20 8423 0113 Fax +44 (0) 20 8864 7008 www.circor.co.uk HOKE ontrols 1901 Lynx Place Ontario, 91761 Tel (909) 923-3770 Fax (909) 923-2550 Texas Sampling, Inc. 3706 Rio Grande Victoria, TX 77901 Tel (361) 575-8087 Fax (361) 575-8157 www.texassampling.com IROR Tech 405 entura ourt Spartanburg, S 29303 Tel (864) 574-7966 Fax (864) 587-5608 www.circortech.com HOKE GmbH Weitzesweg 11 Postfach 15 41-61118 ad Vilbel ortelweil Germany Tel +49 6101 82 56 0 Fax +49 6101 82 56 40 www.hoke.de TOMO 405 entura ourt Spartanburg, S 29303 Tel (864) 574-7966 Fax (864) 587-5608 www.tomcoquickcouplers.com OPK Terbregseweg 120 3056 JX Rotterdam The Netherlands Tel +31 10 420 60 11 Fax +31 10 456 67 74 www.dopak.com HOKE, Inc. 405 entura ourt Spartanburg, S 29303 Tel (864) 574-7966 Fax (864) 587-5608 www.hoke.com LIMITE WRRNTY LL IRLE SEL ONTROLS, IN., GO REGULTOR, N HOKE IN. PRO UTS RE ME TO EXTING STNRS OF ESIGN, MTERIL, WORK MN SHIP N QUL I TY ONTROL N RE WRRNTE TO E FREE OF EFETS IN MTERIL N WORKMNSHIP N RESONLY FIT FOR THE USES SET FORTH IN SELLER S T LOG OR THE ONTRT SPE I FI TIONS FOR PERIO OF ONE YER FTER SLE IF PROPERLY IN STLLE N MINTINE N UNER THE NORML USE N SERVIE FOR WHIH THE EQUIPMENT IS INTENE. UYER TO INSPET THE GOOS WITHIN TEN YS OF ELIVERY N TO THEN IMMEITELY NOTIFY SELLER OF NY EFETS IN ORER TO LIM EFET. THIS WRRNTY IS IN LIEU OF LL OTHER WRRNTIES WHETHER THEY RE STTUTORY, EXPRESS OR IMPLIE, INLUING MONG OTHER THINGS NY IMPLIE WRRNTY OF MER HNT IL I TY FITNESS FOR PRTIULR PURHSE NOT SET FORTH IN SELLER S TLOG, N LSO OES NOT PPLY TO NY PROUTS OF SELLER WHIH HVE EEN REPIRE, LTERE OR MOIFIE OR HVE EEN SUJET TO MISUSE OR USE. SELLER IS NOT LILE FOR NY ONSEQUENTIL, INIENTL OR SPEIL MGES RESULTING IRETLY OR INIRETLY FROM THE ESIGN, MTERIL, WORKMNSHIP, OPERTION OR INSTLLTION OF NY OF ITS PROUTS N NEITHER SSUMES NOR UTHORIZES NY OTHER PERSON TO SSUME FOR IT NY OTHER LIILITY IN ONNETION THEREWITH. UYER S EXLUSIVE REMEY SHLL E THE REPIR OR REPLEMENT OF NY SUH EFETIVE PROUT FTER VERIFITION Y SELLER. THIS WRRNTY IS IN EFFET UNLESS SUPERSEE Y LIMITE WRRNTY, FORM NO. 2299 (4/83) 79020 07/04