SANDVIK LH514 MASS MINING LOADERS TECHNICAL SPECIFICATION Sandvik LH514 is a high capacity Load-Haul-Dump (LHD) developed specially for underground use. By combining smart geometry with powerful thrust, high breakout forces, responsive controls and high tramming speeds it provides fast bucket filling, high fill factors and fast cycle times. The LH514 is the Mining icon since its introduction to the market. CAPACITIES Tramming capacity 14 000 kg Break out force, lift 28 042 kg Break out force, tilt 23 453 kg Tipping load 29 200 kg bucket 5.4 m³ SPEEDS FORWARD & REVERSE (LEVEL/LOADED) 1st gear 5.9 km/h 2nd gear 10.5 km/h 3rd gear 18.3 km/h 4th gear 32.7 km/h BUCKET MOTION TIMES Raising time Lowering time Dumping time 7.0 sec 4.0 sec 2.3 sec OPERATING WEIGHTS Total operating weight Front axle Rear axle 38 100 kg 16 700 kg 21 400 kg LOADED WEIGHTS Total loaded weight Front axle Rear axle 52 100 kg 38 625 kg 13 475 kg
OPERATIONAL CONDITIONS AND LIMITS Environmental temperature operating altitude From -20 C to +50 C With engine Volvo TAD1340VE from -1500 m to +3000 m at 25 C without rated power derate TRANSMISSION Power shift transmission with modulation. Dana 6422, automatic gear shift control, four gears forward and reverse. REQUIREMENTS AND COMPLIANCE Compliance with 2006/95/EC Low voltage directive Compliance with 2004/108/EC Electromagnetic compatibility directive Compliance with 2006/42/EC Machinery directive (Equipment for EU area, achieved with relevant options) Design based on EN 1889-1. Machines for underground mines. Mobile machines working underground. Safety. Part 1: Rubber tyred vehicles. Design based on MDG 15. Guideline for mobile and transportable equipment for use in mines. (Equipment for Australia, achieved with relevant options) AXLES Front axle, spring applied hydraulic operated brakes. Fixed. Rear axle, spring applied hydraulic operated brakes. Oscillating ± 8. TIRES Tire size (Tires are application approved. Brand and type subject to availability.) Kessler D106, limited slip differential. Kessler D106, limited slip differential. 26.5x25 L5S 36 ply Electrical system based on IEC 60204-1. Safety of machinery Electrical equipment of machines Part 1: General requirements CONTAINS FLOURINATED GREENHOUSE GASES (closed cabin option) Refrigerant R134a under pressure max 38 bar/550 PSI: Filled weight: 2,000 kg CO2e: 2,860 tons GWP: 1430 Information based on the F Gas Regulation (EU) No 517/2016 POWER TRAIN ENGINE Diesel engine Output Torque Number of cylinders In-line 6 Displacement Cooling system Combustion principle Air filtration Electric system Emissions Ventilation rate Particulate index Exhaust system Average fuel consumption at 50% load Fuel tank capacity CONVERTER Dana C9602 Volvo TAD1340VE 256 kw @ 2100 rpm 1 770 Nm @ 1260 rpm 12.78 l Liquid cooled and piston pump driven cooler fan 4-stroke, direct injection, turbo with intercooler Two stage filtrarion, dry type 24 V Tier 2, Euro Stage II CANMET 9.96 m³/s, MSHA 15500 CFM MSHA 10500 CFM Catalytic purifier and muffler, double wall exhaust pipe 33.0 l/h 560 l No lock-up OPERATOR S COMPARTMENT CABIN (Cabin option replaces the standard canopy) ROPS certification according to EN ISO 3471 FOPS certification according to EN ISO 3449 Sealed, air conditioned, over pressurized, noise suppressed closed cabin Sound absorbent material to reduce noise Laminated glass windows Cabin mounted on rubber mounts to the frame to reduce vibrations Air conditioning unit located outside the cabin to reduce noise inside the cabin Cyclone pre-filter for A/C device Adjustable joysticks No high pressure hoses in the operator s compartment Inclinometers to indicate operating angle Emergency exit Floor washable with water to reduce dust Three-point contact access system with replaceable and colour coded handles and steps 12 V output Remote circuit breaker switch CANOPY () ROPS certification according to EN ISO 3471 FOPS certification according to EN ISO 3449 Adjustable joysticks No high pressure hoses in the operator s compartment Inclinometers to indicate operating angle Emergency exit Floor washable with water to reduce dust Three-point contact access system with replaceable and colour coded handles and steps 12 V output Remote circuit breaker switch 2 / 10
OPERATOR S SEAT Low frequency suspension Height adjustment Adjustment according to the operator s weight Fore-aft isolation Padded and adjustable arm rests Adjustable lumbar support Selectable damping Two-point seat belt With cabin option only With cabin option only With cabin option only BUCKET HYDRAULICS The oil flow from steering hydraulic pump is directed to bucket hydraulics when steering is not used. Boom system Lift cylinders Dump cylinder Main valve Pump for bucket hydraulics Joystick bucket and boom control (electric), equipped with piston pump that delivers oil to the bucket hydraulic main valve. Z-link 160 mm, 2 pcs 200 mm, 1 pc Open center type Piston type, LS controlled CONTROL SYSTEM, DASHBOARD AND DISPLAYS Sandvik Intelligent Control system Critical warnings and alarms Instrument Panel Instrument Panel My Sandvik Digital Services Knowledge Box on-board hardware Displayed as text and with light 5.7 Display with adjustable contrast and brightness Illuminated switches BRAKES Service brakes are spring applied; hydraulically operated multidisc wet brakes on all wheels. Two independent circuits: one for the front and one for the rear axle. Service brakes also function as an emergency and parking brake. Brake system performance complies with requirements of EN ISO 3450, AS2958.1 and SABS 1589 Neutral brake Automatic brake activation system, ABA Electrically driven emergency brake release pump Brake oil tank capacity 75 l FRAME REAR AND FRONT FRAME High strength structure with optimized material thicknesses. Reduced own weight for higher overall hauling capacity and long structural lifetime. Welded steel construction. Central hinge Tanks Automatic central lubrication HYDRAULICS Filling pump for hydraulic oil Door interlock for brakes and boom, bucket, and steering hydraulics Oil cooler for hydraulic and transmission oil Fittings Hoses Hydraulic oil tank capacity Sight glass for oil level STEERING HYDRAULICS Full hydraulic, centre-point articulation, power steering with two double acting cylinders. Steering lock. Steering main valve Steering hydraulic cylinders Steering pump Steering and servo hydraulic pumps Adjustable upper bearing Rear tanks are bolted to frame, hydraulic tank and cabin base are both bolted and welded to frame Electrical Capability up to 50 C ambient temperature ORFS MSHA approved 240 l 2 pcs Steering controlled by electric joystick. Open center type, LS controlled 125 mm, 2 pcs Piston type Piston type ELECTRICAL EQUIPMENT MAIN COMPONENTS Alternator Batteries Starter Driving lights Working lights Parking, brake and indicator (blinkers) lights Control system Lockable main switch Reverse alarm (CEN) Flashing beacon INCLUDED SAFETY FEATURES FIRE SAFETY Portable fire extinguisher Hot side - cold side design 24 V, 150 A 2 x 12 V, 180 Ah 9 kw, 24 V 2 pcs in front 65W 4 pcs in rear 65W 4 pcs in cabin 65W 1 pc under boom, 65W 2 pcs in front, LED lights 2 pcs in rear, LED lights 5,7 Color display, 5 modules, inbuilt system diagnostics Isolation of combustibles and ignition sources Heat insulation on exhaust manifold, turbo, and isolated exhaust pipe 12 kg (CEN) 3 / 10
ENERGY ISOLATION Lockable main switch, ground level access Emergency stop push buttons according to EN ISO 13850 Pressure release in the radiator cap Automatic discharge for pressure accumulators (brake system and pilot circuit) Frame articulation locking device Mechanical boom locking device Wheel chocks and brackets 1 pc in cabin 2 pcs in rear ALTERNATIVE ENGINES Engine Volvo TAD1171VE, 265 kw, 2100 rpm, Euro Stage IV, MSHA, Canmet (Tier 4f). Applicable from -1500 m to +2500 m at 25 C without rated power derate. Ultra low sulphure fuel and AdBlue required. CANMET ventilation rate 5,90 m3/s. MSHA ventilation rate 12000 CFM and particulate index 1500 CFM. Average fuel consumption at 50 % load 35 l/h. Engine Volvo TAD1350VE, 256 kw, 1900 rpm, Euro Stage III. Applicable from -1500 m to + 3000 m at 25 C without rated power derate. ELECTRICAL OPTIONS Jump start interface Monitoring camera system DOCUMENTATION STANDARD MANUALS Operator s Manual Maintenance Manual Parts Manual Service and Repair Manual ToolMan Decals OPTIONS English and other EU languages English and other EU languages English English, Russian, French 2 x CD and 2 x USB stick in pdf format, includes all the manuals English, Finnish, Swedish, Spanish, Russian, French, Polish, Portuguese, Turkish, German, Norwegian, Estonian, Chinese, Greek OTHER OPTIONS Additional cabin heater element for air conditioning Cover grills for lamps Converter with lock-up, Dana SOH Spare rim 22.00-25/3.0 (for tires 26.5-25) Boom suspension (ride control) Wiggins quick filling set for fuel and oils (hydraulic, engine and transmission) Integrated weighing system Electirc loader towing kit Accordance with CE norms (CEN) EXTRA ITEM No spin rear axle Cold climate package SAFETY OPTIONS Safety cabin, 2-point seatbelt, corner light, ROPS/FOPS and A/C unit. Cabin lift kit (150 mm) Disabled 4th gear (mandatory in EU) Radio remote control HBC CAN Radio remote control interface HBC, analoque, not with automation Recovery kit (brake release by pulling the hook) Video camera system for Radio remote control Proximity Detection Interface Driving direction lights (red / green) LED lights (Replaces standard driving lights) Fire suppression system ANSUL, 2 tanks, 8 nozzles (CEN) including auto engine shutdown (not for automation) Fire suppression system ANSUL, 2 tanks, 8 nozzles (CEN), Checkfire including auto engine shutdown Fire suppression system Sandvik FS1000 with auto engine shutdown, Eclipse foam delivered separately Extra fire extinguisher 12kg Safety rails Emergency steering (CEN) AutoMine TM Onboard Package AutoMine TM Loading, readiness 4 / 10
GRADE PERFORMANCE Volvo TAD1340VE Empty Percent grade 0.0 2. 0 4.0 6.0 8.0 10.0 12.5 14.3 17.0 Ratio 1:12 1:10 1:8 1:7 1st gear (km/h) 5.9 5.9 5.8 5.8 5.8 5.8 5.7 5.7 5.7 2nd gear (km(h) 10.5 10.4 10.4 10.3 10.2 10.2 10.1 9.5 8.5 3rd gear (km/h) 18.4 18.2 18.0 17.8 15.8 13.7 11.9 4th gear (km/h) 32.9 32.3 26.7 21.5 Loaded Percent grade 0.0 2.0 4.0 6.0 8.0 10.0 12.5 14.3 17.0 Ratio 1:12 1:10 1:8 1:7 1st gear (km/h) 5.9 5.9 5.8 5.8 5.8 5.7 5.7 5.7 5.6 2nd gear (km(h) 10.5 10.4 10.3 10.2 10.1 9.5 8.2 7.5 6.7 3rd gear (km/h) 18.3 18.0 17.7 14.7 12.4 4th gear (km/h) 32.7 28.8 5 / 10
DIMENSIONS 6 / 10
DIMENSIONS Bucket alternatives (m³) 4.6 m³ 5.0 m³ 5.4 m³ 6.2 m³ 7.0 m³ Material broken density (kg/m³) max. 3400 kg/m³ max. 3100 kg/m³ max. 2800 kg/m³ 2400 kg/m³ 2000 kg/m³ Lip plate type Bare Lip Bare Lip Bare Lip Bare Lip Bare Lip L1 (mm) 10724 10840 10956 11126 11151 L2 (mm) 10373 10453 10532 10649 10665 L3 (mm) 10052 10140 10227 10355 10375 L4 (mm) 3273 3353 3432 3549 3565 L5 (mm) 1800 1800 1800 1800 1800 L6 (mm) 1800 1800 1800 1800 1800 L7 (mm) 3500 3500 3500 3500 3500 L8 (mm) 2491 2583 2676 2811 2831 L9 (mm) 3069 3185 3301 3471 3496 L10 (mm) 2695 2773 2851 2965 2981 H1 (mm), CC517 2545 2545 2545 2545 2545 H1 (mm), OC410 2559 2559 2559 2559 2559 H2 (mm) 2060 2060 2060 2060 2060 H3 (mm) 456 456 456 456 456 H4 (mm) 425 425 425 425 425 H5 (mm) 850 850 850 850 850 H6 (mm) 1073 1149 1225 1337 1352 H7 (mm) 1586 1586 1754 1878 2409 H8 (mm) 2666 2596 2526 2423 2409 H9 (mm) 3747 3747 3747 3747 3749 H10 (mm) 4080 4080 4080 4080 4080 H11 (mm) 5273 5359 5444 5570 5590 W1 (mm) 2837 2837 2837 2837 3000 W2 (mm) 2700 2700 2700 2700 3000 W3 (mm) 2400 2400 2400 2400 2400 W4 (mm) 2736 2736 2736 2736 2736 A1 11 11 11 11 11 A2 42.5 42.5 42.5 42.5 42.5 R1, left turn (mm) 3141 3141 3141 3141 3141 R2, left turn (mm) 6747 6785 6823 6879 7010 T, left turn (mm) 4381 4419 4601 4658 4789 R1, right turn (mm) 3380 3380 3380 3380 3380 R2, right turn (mm) 6747 6785 6823 6879 7010 T, right turn (mm) 4357 4394 4432 4489 4620 7 / 10
DIMENSIONS Bucket alternatives (m³) 4.6 m³ 5.0 m³ 5.4 m³ 6.2 m³ 7.0 m³ Material broken density (kg/m³) max. 3200 kg/m³ max. 2900 kg/m³ max. 2600 kg/m³ 2200 kg/m³ 1900 kg/m³ Lip plate type GET GET GET GET GET L1 (mm) 10664 10782 10898 11068 11084 L2 (mm) 10373 10448 10527 10644 10654 L3 (mm) 10052 10058 10145 10274 10286 L4 (mm) 3273 3348 3427 3544 3554 L5 (mm) 1800 1800 1800 1800 1800 L6 (mm) 1800 1800 1800 1800 1800 L7 (mm) 3500 3500 3500 3500 3500 L8 (mm) 2408 2502 2595 2756 2742 L9 (mm) 3009 3127 3243 3414 3429 L10 (mm) 2690 2770 2848 2954 2971 H1 (mm), CC517 2545 2545 2545 2545 2545 H1 (mm), OC410 2559 2559 2559 2559 2559 H2 (mm) 2060 2060 2060 2060 2060 H3 (mm) 456 456 456 456 456 H4 (mm) 425 425 425 425 425 H5 (mm) 850 850 850 850 850 H6 (mm) 1070 1148 1148 1335 1344 H7 (mm) 1502 1588 1666 1796 1808 H8 (mm) 2673 2596 2523 2387 2411 H9 (mm) 3709 3709 3699 3699 3700 H10 (mm) 4080 4080 4080 4080 4080 H11 (mm) 5183 5277 5363 5489 5501 W1 (mm) 2886 2886 2886 2886 3098 W2 (mm) 2766 2766 2766 2766 3066 W3 (mm) 2400 2400 2400 2400 2400 W4 (mm) 2736 2736 2736 2736 2736 A1 11 11 11 11 11 A2 42,5 42,5 42,5 42,5 42,5 R1, left turn (mm) 3141 3141 3141 3141 3141 R2, left turn (mm) 6794 6832 6870 6928 7058 T, left turn (mm) 4573 4611 4649 4706 4837 R1, right turn (mm) 3380 3380 3380 3380 3380 R2, right turn (mm) 6794 6832 6870 6928 7058 T, right turn (mm) 4404 4442 4480 4538 4668 8 / 10
DIMENSIONS Bucket alternatives (m³) 5.4 m³ 6.2 m³ 7.0 m³ Material broken density (kg/m³) max. 2700 kg/m³ max. 2300 kg/m³ 1900 kg/m³ Lip plate type Half Arrow Half Arrow Half Arrow L1 (mm) 10941 11112 11155 L2 (mm) 10561 10679 10706 L3 (mm) 10169 10298 10334 L4 (mm) 3461 3544 3606 L5 (mm) 1800 1800 1800 L6 (mm) 1800 1800 1800 L7 (mm) 3500 3500 3500 L8 (mm) 2621 2756 2756 L9 (mm) 3286 3456 3500 L10 (mm) 2882 2996 3022 H1 (mm), CC517 2545 2545 2545 H1 (mm), OC410 2559 2559 2559 H2 (mm) 2060 2060 2060 H3 (mm) 456 456 456 H4 (mm) 425 425 425 H5 (mm) 850 850 850 H6 (mm) 1257 1369 1394 H7 (mm) 1695 1819 1854 H8 (mm) 2491 2387 2365 H9 (mm) 3692 3692 3696 H10 (mm) 4080 4080 4080 H11 (mm) 5386 5512 5547 W1 (mm) 2917 2917 3158 W2 (mm) 2860 2860 3158 W3 (mm) 2400 2400 2400 W4 (mm) 2531 2531 2531 A1 11 11 11 A2 42,5 42,5 42,5 R1, left turn (mm) 3141 3141 3141 R2, left turn (mm) 6926 6984 7118 T, left turn (mm) 4705 4763 4897 R1, right turn (mm) 3380 3380 3380 R2, right turn (mm) 6926 6984 7118 T, right turn (mm) 4536 4594 4728 9 / 10
Sandvik Mining and Rock Technology reserves the right to make changes to the information on this data sheet without prior notification to users. Please contact a Sandvik representative for clarification on specifications and options. Sandvik Mining and Rock Technology 2017 SANDVIK is a registered trademark owned by Sandvik Intellectual Property AB in Sweden and other countries 10 / 10