W1392 Please keep this instruction sheet for future reference, as it contains important information. Requires three C batteries (LR14) alkaline batteries (not included) for operation. Adult assembly is required. Tool required for battery installation: Phillips screwdriver (not included). Wipe this toy with a clean, damp cloth. Do not immerse. This toy has no consumer serviceable parts. Do not take this toy apart. fisher-price.com
Assembled Parts Head Tail Spinner Dome Base 2
Assembly Dome Tail Base 1 Snap the dome onto the base. Hint: The dome is designed to fit onto the base one way. If it does not seem to fit, turn it and try again. Head 3 Fit the tail onto the base. Push to snap in place. Spinner 2 Fit the head onto the base. Push to snap in place. 4 At an angle, fit one end of the spinner into tail, as shown. Push to snap the other end of the spinner in place. 3
Consumer Information CONSUMER ASSISTANCE 1-800-432-5437 (US & Canada) 1300 135 312 (Australia) Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052. Hearing-impaired consumers: 1-800-382-7470. Outside the United States: Canada: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2; www.service.mattel.com. Great Britain: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303. www.service.mattel.com/uk Mattel Europa B.V., Gondel 1, 1186MJ Amstelveen, Nederland. Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland. ICES-003 This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. NMB-003 Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. L utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, meme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. FCC Statement (United States Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Consult the dealer or an experienced radio/tv technician for help. Note: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. PRINTED IN CHINA 2012 Mattel. All Rights Reserved. 4 W1392a-0920
Battery Installation 1,5V x 3 C (LR14) Locate the battery compartment door on the bottom of the dino base. Loosen the screws in the battery compartment door and remove the door. Insert three, new C (LR14) alkaline batteries. Hint: We recommend using alkaline batteries for longer battery life. Replace the battery compartment door and tighten the screws. If this toy begins to operate erratically, you may need to reset the electronics. Slide the power/volume switch off and then back on. When sounds or motion from this toy become faint or stop, it s time for an adult to change the batteries. Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities. 5 Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). Insert batteries as indicated inside the battery compartment. Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries inside may explode or leak. Never short-circuit the battery terminals. Use only batteries of the same or equivalent type, as recommended. Do not charge non-rechargeable batteries. Remove rechargeable batteries from the product before charging. If removable, rechargeable batteries are used, they are only to be charged under adult supervision.
Ball-popping Action! Power/Volume Switch Roll a ball down the tail ramp Spin the roller Slide the power/volume switch to ON with low volume or ON with high volume. Spin the roller on the front of the dino. Roll a ball down the dino s tail or drop it in the base to see it bounce around inside the dino, pop out or roll out his mouth! When you are finished playing with this toy, slide the power/volume switch OFF. 6