Page of 7 Application control unit, in conjunction with the associated hydraulic set provides a complete pressure independent balancing and control group for efficient and effective individual room or central-controlled energy management in 4-pipe systems, such as: Heating and cooling ceilings Convectors Decentralised ventilation units Fan coil systems Convection heating & cooling units provides modulating control, which works independently of any variations in the differential pressure of the system. The hydraulic set consists of an OPTIMA Compact pressure independent control valve with a -V modulating actuator, and two port control valves with on/off actuators. The heart of the hydraulic set is the OPTIMA Compact pressure independent control valve that always provides full valve authority with its combination of adjustable dynamic volume controller and modulating control valve. enefits Energy saving through optimum pressure-independent flow limitation and regulation Modulating control for both cooling and heating with only one data point No balancing valves required in the system Less time spent in the selection and sizing as only the data flow and min DP required Full comfort without recommissioning if the system is expanded during the construction phase Small space requirements for OPTIMIZER Control Unit Simple, flexible and quick installation due to separate components Features The presetting function has no impact on the stroke; Full stroke modulation at all times, regardless the preset flow The constant differential pressure across the modulating control component guarantees % authority Automatic balancing eliminates overflows, regardless of fluctuating pressure conditions in the system Thermal actuator on/off and -V, normally closed High flows with minimal required differential pressure due to advanced design of the valve Small dimensions due to compact housing Higher presetting precision due to stepless analogue scale EN DEC 5 Individual or central room temperature control
Page of 7 Function controls both heating and cooling with only one single data point from the MS system, through a -V external control signal (). Full modulation is provided with even different design flow of heating and cooling. The design flow rate for the cooling system defines the maximum flow through the coil and is set using the Pressure Independent way Control Valve, Frese OPTIMA Compact (see page 5). Controller offers setting of hot water flow, from % down to % of the maximum flow. The Heat Offset flow can be set using the dial on the Controller () - each dot indicates % of maximum flow. The switch over from cooling to heating is automatically changed via the signal from the MS data point. The pressure in the heating and cooling system must be the same to achieve correct function. Max kpa in pressure difference. Frese OPTIMA Compact pressure independent control valve is closed during the switch over and remains closed for approx. minutes until switching of the port control valves has been safely completed. The switch over condition is signaled by the flashing of the Off-LED lamp. () Controller Technical data Controller Protection class: IP to EN 659 Supply: (max. 5 VA) Control signal: -V DC Ambient operating conditions: C to 4 C -9% RH Weight: 68 g % Example with Heat Offset at 4% flow 9% EN DEC 5 Flow 8% 7% 6% 5% 4% % % % % 75% Cooling 5% 5% Switch over zone from cooling to heating 4% % Heating % %.5.5.5.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 Cooling V - 4,5V Heating 5,5V - V External input voltage signal
4 5 6 7 8 9 EXTERN -V ON/OFF ON/OFF Technote Page of 7 Technical data actuators Characteristics: Thermo actuators, normally closed Protection class: IP 54 to EN 659 Frequency: 5/6 Hz Control signal: -V DC or on/off Actuating force: N Stroke: max. 5.5 mm Running time: s -V/8 s on/off Ambient operating conditions: C to 6 C Cable length:. m Weight: g On/Off actuator.5 mm stroke, -DC/ 8s NC (DN5) 48-555 On/Off actuator.5 mm stroke, -DC/ 8s N (DN5) 48-55 Modulating actuator.5-5.-5.5 mm stroke /-V DC s/mm 48-559 Hydraulic connection and electrical wiring A A Heating Supply Coil Cooling 4 5 6 7 8 9 -V DC -V DC A A Heating Return Cooling -V DC -V DC EXTERN -V ON/OFF ON/OFF Extern input signal MS Heating inlet Cooling inlet EN DEC 5 Heating outlet Cooling outlet
H4 H H H Technote Page 4 of 7 Technical data OPTIMA Compact Valve housing: DZR rass, CW6N DP controller: PPS 4% glass Spring: Stainless steel Diaphragm: HNR O-rings: EPDM Pressure class: PN5 Max. differential pressure: 8 kpa Medium temperature range: C to C Technical data port control valve Valve housing: Cast rass, CW67N O-rings: EPDM Pressure class: PN6 Medium temperature range: C to C Kvs,5 DN5 5,5 DN5 The pipe system shall be properly ventilated to avoid risk of air pockets. Glycolic mixtures up to 5% are applicable (both ethylene and propylene). Frese A/S can accept no responsibility if another actuator is used instead of the Frese actuator A L L A A A L4 L L5 Dimension Size DN5 DN5 L 56 L* 56 76 Length L 76 54 L4* 9 74 L5 65 68 H 59 78 H* 8 Height H 89 H4 9 EN DEC 5 *) Dimensions without Couplings
Page 5 of 7 Frese OPTIMA Compact Low 5. DN5 Flow l/s. l/h 4 Kv (m /h)..5.7 min. Δp kpa.9 7..8 6.5.56 5.7.8 4.9 4.6 4 Frese OPTIMA Compact High 5. DN5 l/s Flow.89.6 l/h 4.8 Kv (m /h).5. min. Δp kpa.7.6..6.78.7.5 9. 8.94.67 7 6 9..9 5..8.56 4 7. 6..8 EN DEC 5 For further details: See OPTIMA Compact Technote Pre-set 4
Page 6 of 7 Frese OPTIMA Compact High 5.5 DN5L Flow l/s. l/h 4 Kv (m /h). 4. 6. min. Δp kpa 7.5.97 5..8 9.5.694 5.556 8..47 5.78 7.4.9 5 7. 4 Pre-set Product programme OPTIMIZER Control Unit Size Type Flow l/h Item no. DN5 DN5 DN5 Low Flow incl. couplings High Flow incl. couplings incl. couplings Product programme OPTIMA Compact for OPTIMIZER Control Unit 65-7 5-8 - 5-8 6-69 5-84 Low Flow 65-7 5-8 High Flow - 5-8 DN5 6-69 5-85 Size Type Flow l/h Item no. EN DEC 5 OPTIMA Compact 5,mm Low 65-7 5- DN5 OPTIMA Compact 5,mm High - 5-5 DN5L OPTIMA Compact 5,5mm High 6-69 5-
Page 7 of 7 Mounting of Controller controller can be mounted either on the pre-insulated pipe using the pipe connectors or on a DIN rail using the DIN rail clips. (DN5 only with DIN rail clips) Controller mounted with pipe connector on the pre-insulated pipe Controller mounted with DIN rail mounting clips Text for technical specifications EN DEC 5 System specifications: The system shall contain a modulationg control for both heating and cooling, with only one data point from the external MS system. The maximum flow for cooling shall be set on the pressure independent control valve and the heating flow shall be set on the Controller in the range from % to % of maximum flow. The system shall consist of pcs. Controller mounted on a pipe connection with unions, pcs. pressure independent control valve, pcs. port control valves, pcs. -V modulating actuator, pcs. on/off actuators. Pressure independent control valve specifications: The length of the modulating stroke shall be independent of flow setting. The modulation and flow setting shall be one combined unit with a linear modulating motion and a rotational flow setting motion. The valve characterization shall not be changed at different flow settings. The pressure independent control valve shall contain a combined flow setting, differential pressure control and modulating bonnet assembly. The valve shall have an external adjustable analogue step less presetting scale from minimum to maximum flow. The valve shall be capable of closing against a maximum differential pressure of 7 kpa (6 bar) DN5 and 8 kpa (8 bar) DN5 with a leakage rate at maximum,% of max rated volumetric flow and comply to EN49 Class IV. The pressure independent control valve shall have a maximum operating differential pressure of 8 kpa (8 ar) Frese A/S assumes no responsibility for errors, if any, in catalogues, brochures, and other printed matter. Frese A/S reserves the right to modify its products without prior notice, including already ordered products, if this does not alter existing specifications. All registered trademarks in this material are the property of Frese A/S. All rights reserved. Frese A/S Sorøvej 8 DK- 4 Slagelse Tel: +45 58 56 Fax: +45 58 56 9 info@frese.dk