Assembly Instructions John Deere EZ View Dust Diverter. Install hinges to bottom front (decal side), approximately from each end. Use Phillips head Screws. (See Picture #). Install 3 / or metal lip (depending on model) to the bottom rear. Use Phillips head screws. (See Picture #) 3. Remove feeder house inspection covers and the right side chain shield.. Raise feeder house to highest level. 5. Place EZ View on feeder house, position over inspection holes so unit clears lights, steps, etc.. When satisfied with position, screw hinges to feeder house with self drilling screws.. Place drive unit on back side of board/rail and sprocket on top of chain. (See Picture #). Place poly strip between chain, board and under sprocket. (See Picture #3) 9. With belt on pulleys, move drive unit back to take looseness out of belt. (See Picture #). With drive unit square with top board or rail, locate and drill 3/ holes through top and bottom boards/rails. (Bolts go under rail with steel.) (See Picture #). Bolt drive unit in place with 3/ x 3 / bolts, washers and nuts. (Bolts go through holes in board/rail or under the poly-steel rails. Use one plate on outside of board/rail and one plate on back side of drive unit. (Leave bolts loose.) (See Picture #3). Use 3/ x carriage bolt, washer and nut to bolt drive unit and back plate together. This prevents drive unit from sliding up. (Leave bolts loose.) (See Picture #3). Center poly wear strip under sprocket and screw to board/rail.. IMPORTANT: Position chain so chain roller or chain pin is directly under center of chain sprocket on drive unit. This will prevent any binding so drive unit runs smoothly. (See Picture #) 5. Tighten all (3) drive unit bolts.. Belt idler: attach spring to rear cover bracket by drilling a small hole. Belt does not need to be real tight.. Remove belt and tip the unit forward. Place weather strip on poly around holes. Tip the unit back down and screw bolt latches to feeder house with self drilling screws. Replace the belt and adjust belt keeper very close to the belt.. For units with wood board/rail: Place chain stabilizer board on top of the chain in front of the drive unit. Drill / holes, bolt and tighten. Board runs right on the chain. (See Picture #3) 9. Install end covers on the EZ View unit.
Picture # Picture #
Poly Wear Strip Picture #3 (Non-STS Models) STS Models
Center Picture #
3 5 XX= ABBREVIATION GN NY COLOR JD GREEN NH YELLOW 9 ITEM NO. PART NUMBER DESCRIPTION QTY. EZ 300-XX 3" EZ-View BODY EZ 35-XX End Cover 3 EZ 35 " CW FAN (HUB TO INSIDE) EZ 3 " CCW FAN (HUB TO INSIDE) 5 EZ 330 Pulley /" x 5/" EZ 3 Middle Bearing Support EZ 3 EZ VIEW END SUPPORT BRKT EZ 33 End Cover Bracket 9 EZ 3 End Cover Plastic Knob EZ 35 5/" BOLT CAST BEARING WITH HOUSING EZ 93 SHAFT 5/" x 9" 3-BR 3/" BOLT RETAINER -3 CB /" X 3/" CARRIAGE BOLT - CB /" X " CARRIAGE BOLT 5 -W USS /" FLAT WASHER -NLN /" NYLON LOCK NUT 5-3 CB 5/" X 3/" CARRIAGE BOLT 5-W USS 5/" FLAT WASHER 9 5-FSN 5/" FLANGE SERRATED NUT 9 9 0 0 5-3 HB 5/' x 3/" HEX HEAD BOLT EZ 330 EZ VIEW DECAL 5 0 UNLESS OTHERWISE SPECIFIED: DO NOT SCALE DRAWING SCALE: : NAME DATE 5 DRAWN MLB 0-- DIMENSIONS ARE IN INCHES REVISED TOLERANCES= VENDOR: FRACTIONAL: +/- /" TITLE: ANGULAR: +/-.5 TWO PLACE DECIMAL: +/-.0 VENDOR PART NO: THREE PLACE DECIMAL: +/-.0 INTERPRET GEOMETRIC TOLERANCING PER: DWG. NO. THE INFORMATION CONTAINED IN THIS MATERIAL: DRAWING IS THE SOLE PROPERTY OF GVL POLY. ANY REPRODUCTION IN PART FINISH: OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF GVL POLY IS PROHIBITED. 3" EZ VIEW ASSEMBLY EZ 3JD03 EZ 3CT03 REV 0
3 5 XX= ABBREVIATION GN NY 9 COLOR JD GREEN NH YELLOW ITEM NO. PART NUMBER DESCRIPTION QTY. EZ 500-XX 5" EZ-View BODY EZ 35-XX End Cover 3 EZ 35 " CW FAN (HUB TO INSIDE) EZ 3 " CCW FAN (HUB TO INSIDE) 5 EZ 330 Pulley /" x 5/" EZ 3 Middle Bearing Support EZ 3 EZ VIEW END SUPPORT BRKT EZ 33 End Cover Bracket 9 EZ 3 End Cover Plastic Knob EZ 35 5/" BOLT CAST BEARING WITH HOUSING EZ 55 SHAFT 5/" x 5" 3-BR 3/" BOLT RETAINER -3 CB /" X 3/" CARRIAGE BOLT - CB /" X " CARRIAGE BOLT 5 -W USS /" FLAT WASHER -NLN /" NYLON LOCK NUT 5-3 CB 5/" X 3/" CARRIAGE BOLT 5-W USS 5/" FLAT WASHER 9 5-FSN 5/" FLANGE SERRATED NUT 9 9 0 0 5-3 HB 5/' x 3/" HEX HEAD BOLT EZ 330 EZ VIEW DECAL 5 0 UNLESS OTHERWISE SPECIFIED: DO NOT SCALE DRAWING SCALE: : NAME DATE 5 DIMENSIONS ARE IN INCHES TOLERANCES= FRACTIONAL: +/- /" ANGULAR: +/-.5 TWO PLACE DECIMAL: +/-.0 THREE PLACE DECIMAL: +/-.0 INTERPRET GEOMETRIC TOLERANCING PER: MATERIAL: FINISH: DRAWN REVISED VENDOR: VENDOR PART NO: MLB 0-- TITLE: DWG. NO. THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF GVL POLY. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF GVL POLY IS PROHIBITED. SIZE: 5" EZ VIEW ASSEMBLY B EZ 5JD03 EZ 5CT03 WEIGHT: REV 0 SHEET OF
ITEM NO. PART NUMBER DESCRIPTION QTY. EZ 30 Chain Board Stiffener EZ 30 Chain Stabilizer Board 3 EZ 3 SLIDE BOLT LOCK ("x /") EZ 3 HINGE (3" X ") 5 EZ 3 WEATHER STRIPPING 3/"x/" EZ 3 Chain Stabilizer Board EZ 339 /" x 5 /" Poly Wear Strip EZ 30 " SHEETROCK SCREW 9 EZ 350 BELT 9" (L 90) EZ 35 IDLER SPRING EZ 35 " x 5" Lip EZ 353 3 /" X 5" LIP EZ 3 3 /" 3" LIP EZ 33 " X 3" LIP -5 FPTS #x5/ FH PHILLIPS TS SCREW -3 DTS X 3/" DRILL & TAP SCREW - CB /" X /" CARRIAGE BOLT 5 -NLN /" NYLON LOCK NUT 3- CB 3/"x" CARR BOLT-SHORT NECK 3-3 HB- 3/" X 3 /" HX HD BOLT GRD 3-FSN 3/"" FLANGE SERRATED NUT 3 9 3-NLN 3/" NYLON LOCK NUT 0 3-W USS 3/" FLAT WASHER 5 9 3 0 5 5 9 0 TITLE: JD 5" & 3" EZ-VIEW SIZE B DWG. NO. EZ 5JD03 EZ 3JD03 REV SCALE: : WEIGHT: SHEET OF
NO. PART NUMBER DESCRIPTION QTY. EZ 305 EZ 3 EZ VIEW DRIVE PLATE PULLEY " X 5/" 3 EZ 3 5/" BEARING AND FLANGE EZ 3 IDLER PULLEY 3" x/" x 3/" 5 EZ 30 # 0 SPROCKET EZ 33 5/" x 5/" SHAFT 3- KS 3/x3/x Key Stock EZ 3 Belt Keeper 9 EZ 303 BELT IDLER ARM 3- CB 3/" X " CARRIAGE BOLT 3- HB 3/" X 3/" HEX BOLT 3-FSN FLANGE SERRATED NUT -3 CB /" X 3/" CARRIAGE BOLT -NLN /" NYLON LOCK NUT 5 -W USS /" USS FLAT WASHER 3-W USS 3/" USS FLAT WASHER 3 3-NLN 3/" NYLON LOCK NUT 5- NSS 5/" X /" NYLON SOCKET SET SCREW 3 9 5 5 5 3 3 TITLE: JD EZ-VIEW DRIVE ASSEMBLY SIZE B DWG. NO. EZ JD53 SCALE: : WEIGHT: REV B SHEET OF