TROPIC Spread Lavatory Faucet with EverClean Finish & SpeedConnect Drain Installation Instructions 708.80 Congratulations on purchasing your American Standard faucet with EverClean finish and Speed Connect drain, two features found only on American Standard faucets. EverClean Finish One wipe effortlessly removes spots SpeedConnect Drain* Eliminates the need for cleaners and scrubbing Fewer parts, installs in less time Permanent surface protectant remains beautiful Never needs adjustment for the life of the faucet EverClean available on: Polished Chrome, Satin Nickel, Stainless Steel, Polished Brass (or any combination of these finishes) Certified to comply with ANSI A.8. M9889 Guaranteed to seal properly the first time, every time. *Your new American Standard faucet is designed to work only with the SpeedConnect drain. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Required tools A Screwdriver INSTALL SPOUT CAUTION Turn off hot and cold water supplies before beginning. Insert SPOUT () and CABLE CONNECTOR () through center hole, making sure the SPOUT ESCUTCHEON () and SEAL WASHER () are properly seated. Assemble RUBBER WASHER (), BRASS WASHER () and LOCKNUT () onto SPOUT SHANK (7) from under side of sink. Make sure SPOUT () is centered in the mounting hole and the slot in the BRASS WASHER () faces toward the rear of the sink. Tighten LOCKNUT () firmly. INSTALL VALVE BODY Channel Locks Place RUBBER RING (9) into ADAPTER (0). Adjustable Wrench Install LOCKNUT () and RUBBER WASHER () onto VALVE BODY (). From under side of mounting surface, install VALVE BODY () through valve mounting holes. Threads of VALVE BODY () should extent at least / of a inch above mounting surface top. Thread ADAPTER (0) onto VALVE BODY () until snug against internal stop. If necessary, adjust LOCKNUT (). Tighten LOCKNUT () with WRENCH (8) (supplied) to secure VALVE BODY (). Repeat above steps for opposite VALVE BODY (A). Tubing Cutter SLOT 7 /'' MIN. 0 9 MOUNTING SURFACE 0 9 a 8
POP-UP Remove CLEAR PLASTIC COVER (). Remove CARDBOARD SPACER () from under POP-UP (). Tighten TAILPIECE () on BODY before installing BODY. BODY REMOVE FLANGE Thread FLANGE () counter-clockwise and remove FLANGE () and FOAM GASKET () from drain body. Thread LOCKNUT () clock-wise to bottom of drain body. Push GASKET () down against LOCKNUT (). INSTALL FROM BELOW FIXTURE REAR OF SINK From under side of SINK install BODY () up through drain outlet. Note: No plumber s putty or caulk is required. The CABLE ATTACHMENT POINT () must face towards the rear of the SINK. Install FOAM GASKET () and FLANGE () onto drain body from above SINK and tighten FLANGE () firmly. OUTLET TIGHTEN LOCKNUT Tighten LOCKNUT () firmly with Adjustable Wrench or Channel Locks. FLANGE GASKET AND POP-UP KNOB Check FLANGE in SINK to ensure that WHITE FOAM GASKET () is fully compressed and not visible. DOWN POP-UP KNOB () must be fully down. WHITE FOAM GASKET NOT VISIBLE FLANGE M9889
7 ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR () clockwise onto BODY CONNECTION () and hand tighten. Your new POP-UP installation is now complete. Note: Tailpeice on pop-up drain is -/ O.D. -/ O.D. 8 CHECK OPERATION OF POP-UP Operate LIFT KNOB () to verify that STOPPER () opens and closes. Note: If STOPPER () does not open and close properly then refer to the troubleshooting section of these instructions. 9 MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY. Thread TEE BODY () to SPOUT SHANK (). Thread HOSE CONNECTOR (, A) to VALVE CONNECTIONS (7, 7A). Connect water supply to VALVE BODIES (,A) with /" IPS FLEXIBLE SUPPLIES () or /8" O.D. BULL-NOSE RISERS (). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. Connect -/ O.D. tailpiece on POP-UP to waste outlet. /" PIPE THREAD FLEXIBLE SUPPLIES 7 WASTE OUTLET A A 7A COUPLING NUT /8 O.D. BULL-NOSE RISERS COMPRESSION NUT FERRULE COLD HOT /8 COMPRESSION CONNECTION M9889
0 INSTALL HANDLES Push ADAPTER () on VALVE STEM (), so that the hole of the ADAPTER () without a spline is facing up. Tighten STEM SCREW () to secure ADAPTER (). Find correct position of LEVER HANDLE ASSEMBLY () by adjusting male teeth on ADAPTER () to female teeth in HANDLE (). Thread LEVER HANDLE ASSEMBLY () onto DECK ADAPTER () until snug against mounting surface. TOP THREAD ON TO DECK ADAPTER SPLINE END DOWN TEST INSTALLED FITTING With HANDLES () in OFF position, turn on WATER SUPPLIES () and check all connections for leaks. Remove AERATOR (). Operate both HANDLES () to flush water lines thoroughly. Replace AERATOR (). CHECK CONNECTIONS Operate POP-UP KNOB () and fill Sink with water. Check that STOPPER () makes a good seal and retains water in Sink. If STOPPER () does not seal properly, please refer to Troubleshooting Guide in these instructions. Release POP-UP KNOB () down and check all drain connections and "P" trap for leaks. Tighten if necessary. WASTE OUTLET COLD EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with clean water may also be used, if desired. No additional cleaning products are required. DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface. SERVICE HOT To change direction of handle rotation, proceed as follows: UNTHREAD Turn valve to OFF position. Unthread HANDLE BASE () from DECK ADAPTER (). Pull HANDLE ASSEMBLY off VALVE STEM (). Remove SPRING CLIP (). Lift STOP WASHER (), turn 90 and replace. Replace SPRING CLIP (). Find correct position of HANDLE ASSEMBLY by adjusting male teeth on VALVE STEM () to female teeth in HANDLE. Thread HANDLE ASSEMBLY onto DECK ADAPTER () until snug against mounting surface. If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90. P TRAP 90 HANDLE ASSEMBLY M9889
SpeedConnect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position: Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode. CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector () counter-clockwise. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration. Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the Stopper should be in the UP position. Fig. B, C. Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C. Re-attach the Cable to the Drain Body Connection () by threading the Cable Connector () clockwise onto the Drain Body Connection () and hand-tighten. Fig. C. DOWN CAM RE-ATTACH STOPPER LIFT-KNOB DISCONNECT CAM CAP STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector () counter-clockwise. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration. Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D. Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E. The Stopper can now be removed by lifting it out of the Drain. Fig. F. Fig. D. Fig. E. REMOVE CAM Fig. F. REMOVE CAM CAP M9889
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, Locked Mode (Stopper cannot be removed) or Unlock Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in Locked mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.fig. G. Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J. Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not snap into place, then rotate the Cam to make sure it is fully inserted. Fig. K. Re-attach Cable. See CABLE ADJUSTMENT PROCEDURE in Troubling Shooting Guide to complete installation. Stopper will be in Locked mode and not be removable. LOGO LOOP TOWARD REAR OF SINK Locked Mode (Vandal Proof) Fig. G. Unlocked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. H. To install the stopper in Unlocked mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down. Fig. H. Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J. Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not snap into place, then rotate the Cam to make sure it is fully inserted. Fig. K. Re-attach Cable. See CABLE ADJUSTMENT PROCEDURE in Troublingshooting Guide to complete installation. Stopper will be in Unlocked mode and removable. LOGO 80 LOOP TOWARD FRONT OF SINK Unlocked Mode Fig. H. Fig. J. Fig. K. CAM INSTALL CAM INSTALL CAM CAP M9889
TROPIC Spread Lavatory Faucet with POP-UP M90-YYY0A LIFT ROD KNOB M97-YYY0A SPOUT KIT MODEL NUMBER 708.80 0070-YYY0A AERATOR M98-YYY0A ESCUTCHEON KIT Replace the "YYY" with appropriate finish code CHROME SATIN NICKEL 00 9 M98-0070A DECK ADAPTER KIT M97-0070A SPOUT MTG. KIT M9-0070A VALVE MTG. KIT M99-YYY0A HANDLE (RIGHT OR LEFT) 98-0070A HANDLE SCREW 9809-0070A ADAPTER 990-0070A CARTRIDGE M900-0070A TEE & HOSE KIT M9-YYY0A STOPPER ASSEMBLY M90-0070A CABLE ASSEMBLY 00-0070A SUPPLY NUT M9-YYY0A ASSEMBLY M990-000A TAILPIECE (NOT INCLUDED WITH FAUCET) M97-007A FLANGE ASSEMBLY M987-0070A CAM SEAT INSERT M90-0070A CAM ASSEMBLY M907-0070A TAILPIECE INSERT A99-000A TAILPIECE HOT LINE FOR HELP For toll-free information and answers to your questions, call: (800) -90 Weekdays 8:00 a.m. to 8:00 p.m. EST IN CANADA -800-87-09 (TORONTO -90-0-09) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 0-800-89--00 Product names listed herein are trademarks of American Standard Inc. American Standard Inc. 00 7 M98-0070A MOUNTING KIT M9889