INSTALL GUIDE DOCUMENT NUMBER 8457 REVISI DATE 7 FIRMWARE ORB-AL(RS)-CH4-[ADS-ALCA] HARDWARE ADS-ALCA ESSORIES ADS-USB (REQUIRED) ADS-HRN-CH4 (REQUIRED) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. BEFORE INSTALLATI - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)
PAGE OF 8 DOC.: #8457 7 VEHICLE LIST - OF FEATURES X LOCK /STANDALE MOD. PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DATA/MUX IGNITI CTRL SECURE TAKEOVER PARKING LIGHT CTRL -0 00c AT -0 00c SRT8 AT -0 INSTALL TYPE MAKE CHRYSLER DODGE JEEP RAM VW POWER SLIDING DOOR (R) DATA IMMOBILIZER BYPASS -0 00 Limited AT POWER SLIDING DOOR (L) YEAR 00 AT POWER LIFTGATE MODEL NOTE I Install type requires a T-Harness to complete the installation. T-Harness sold separately. Town & Country AT -6 Caravan AT -0 Challenger SXT AT -4 Challenger R/T AT -4 Challenger SRT8 AT -4 Charger SE AT -0 Charger R/T AT -0 Charger SRT8 AT -0 Durango AT - Grand Caravan AT -7 Journey AT 09-0 Magnum AT Commander AT -0 Grand Cherokee AT - C/V AT 0-5 500 AT 0-500 AT 0-500 AT 0-4500 AT - 5500 AT - Routan AT 09- Automotive Data Solutions Inc.
PAGE OF 8 DOC.: #8457 7 BOX CTENTS - OF BOX CTENTS WHITE WHITE 4 PIN BLACK CNECTOR 6 PIN WHITE CNECTOR MODULE 4 5 6 4 5 6 7 WHITE BLUE PROGRAMMING BUTT 0 PIN BLACK CNECTOR 7 PIN WHITE CNECTOR LED A B F C E D 0 9 8 7 6 5 4 4 BLACK PIN WHITE CNECTOR DATA CABLE PIN BLUE CNECTOR DATA CABLE BLACK DATA PORT (WEBLINK, RF, TELEMATIC) WEBLINK CABLE (required accessory sold separately) CH4 T-HARNESS (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT CH4 T-HARNESS COMPUTER USB PORT 4 PIN BLACK CABLE Automotive Data Solutions Inc.
PAGE 4 OF 8 DOC.: #8457 7 COMPATIBLE ESSORIES - OF RF KIT (accessories sold separately) RF KIT FLASH RF DECODER BEFORE INSTALLATI 5 AMPS V (+) RED BLACK BLUE MODULE DATA PORT BLACK BLUE CABLE Automotive Data Solutions Inc. RF DECODER BLACK CABLE ANTENNA
MODULE LOCATI POLARITY WIRE COLOR POSITI CNECTOR TYPE CNECTOR COLOR CNECTOR NAME WIRE DESCRIPTI YEAR MODEL MAKE CHRYSLER DODGE JEEP RAM VW COMPENT LOCATOR PAGE 5 OF 8 DOC.: #8457 7 TYPE - WIRE CHART - OF 00-0 Parking Light 0 pin 00 Limited -0 Parking Light 0 pin 00C -0 Parking Light 0 pin 00 SRT8-0 Parking Light 0 pin Town & Country -0 Parking Light 0 pin Town & Country -6 Parking Light 6 pin White/Green Caravan -0 Parking Light 0 pin Challenger R/T -4 Parking Light 0 pin Challenger SXT -4 Parking Light 0 pin Challenger SRT8-4 Parking Light 0 pin Charger SE -0 Parking Light 0 pin Charger R/T -0 Parking Light 0 pin Charger SRT8-0 Parking Light 0 pin Durango - Parking Light 6 pin White/Green Grand Caravan -0 Parking Light 0 pin Grand Caravan -7 Parking Light 6 pin White/Green Journey 09-0 Parking Light (+) Magnum 0 pin Commander -0 Parking Light (-) Grand Cherokee -0 Parking Light (-) Grand Cherokee - Parking Light 0 pin White/LtGreen C/V 0 Parking Light 0 pin C/V -5 Parking Light 6 pin White/Green Parking Light 500 0- Parking Light 0 pin White 500 0- Parking Light 0 pin White 500 0- Parking Light 0 pin White 4500 - Parking Light 0 pin White 5500 - Parking Light 0 pin White Routan 09- Parking Light 0 pin Automotive Data Solutions Inc.
PAGE 6 OF 8 DOC.: #8457 7 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITI SWITCH A A B IGNITI CNECTOR F C E DATA D A B A IGNITI HARNESS 4 5 6 4 5 6 7 C A 0 YELLOW - PARKING LIGHT OUTPUT YELLOW/RED (NC) YELLOW/BLACK (NC) D E COMPATIBLE ESSORY 4 F IMPORTANT: SEE THE COMPATIBLE ESSORIES PAGE FOR DETAILS. VEHICLE 4 5 6 7 8 9 0 0 GREEN/BLACK- HOOD STATUS (-) INPUT BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE (NC) BLACK/WHITE (NC) 09 GREEN - RAP SHUTDOWN (-) OUTPUT 0 PURPLE/WHITE (NC) CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT WITHOUT OEM HOOD SWITCH: INSTALL AND CNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH (-) PARKING LIGHT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT (-) OR PARKING LIGHT (+) THE FEATURE IS NOT SUPPORTED DRIVER DOOR PIN (-) Automotive Data Solutions Inc.
MODULE PROGRAMMING PROCEDURE - STD KEY - OF 0 Close driver door. Turn key to position. Re-open driver door to wake up data bus. Remove key. Insert key into ignition. 09 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. Turn key to position. 0 Wait, LED will turn solid GREEN for seconds. LED will turn solid RED. Module Programming Procedure completed. Within 5 seconds, LED will flash GREEN rapidly. PAGE 7 OF 8 DOC.: #8457 7 Automotive Data Solutions Inc.
MODULE PROGRAMMING PROCEDURE - PTS - OF 0 Close driver door. Press UNLOCK on the OEM remote. Re-open driver door to wake up data bus. Wait, LED will turn solid GREEN for seconds. DO NOT PRESS BRAKE PEDAL. Push start button twice [x] to position. 09 Module Programming Procedure completed. STOP PAGE 8 OF 8 DOC.: #8457 7 ENGINE STOP LED will turn solid RED. Within 5 seconds, LED will flash GREEN rapidly. STOP DO NOT PRESS BRAKE PEDAL. Push start button once [x] to position. ENGINE STOP Automotive Data Solutions Inc.
VALET MODE PROGRAMMING PROCEDURE - OF NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 0 Time restriction. Complete next step within 7 seconds. PAGE 9 OF 8 DOC.: #8457 7 To exit valet mode: repeat steps to 5. Cycle ignition five times [5x /] rapidly. ENGINE STOP Wait, LED will turn solid RED for seconds. Set ignition to position. ENGINE STOP Valet Mode Programming Procedure completed. Automotive Data Solutions Inc.
AFTERMARKET REMOTE PROGRAMMING PROCEDURE - OF WARNING: Program aftermarket remotes before usage. A maximum of four [4x] aftermarket remotes per system. LED will flash GREEN once [x]. 0 Time restriction. Complete next step within 7 seconds. LED will turn solid RED. Cycle ignition five times [5x /] rapidly. To program additional remotes: repeat steps 4 to 7 using each additional remote. LED will turn solid RED. Wait, LED will turn. Time restriction. Complete next step within seconds from previous step. 09 PAGE 0 OF 8 DOC.: #8457 7 ENGINE STOP Set ignition to position. ENGINE STOP Press once [x] on LOCK button of aftermarket remote. Automotive Data Solutions Inc. 0 Aftermarket Remote Programming Procedure completed.
PAGE OF 8 DOC.: #8457 7 MODULE NAVIGATI PROCEDURE - OF It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. Module must be programmed to the vehicle. Use the Module Navigation Chart on the next page. Set ignition to position. TO ESS THE MENUS: Press and hold programming button until LED turns solid GREEN. IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 TO ESS THE OPTIS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATI. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. 4 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE STOP [X] Automotive Data Solutions Inc.
PAGE OF 8 DOC.: #8457 7 [Y] OPTIS [X] MENUS MODULE NAVIGATI CHART: NOTES I Default settings are listed in bold. 0 0 0 0 0 ENABLE DISABLE* 0 45 SEC 90 SEC MIN MIN 0 DISABLE N/A LOCK + UNLOCK + LOCK LOCK + LOCK + LOCK 0 MIN MIN 0 MIN 5 MIN 5 MIN 0 MIN 5 MIN 5 MIN 0 SEC SEC SEC 0 SEC 5 SEC 0 SEC 5 SEC 0 SEC 0- N/A 0 N/A 0 0 N/A 0 II Make sure the option is covered on the vehicle before attempting to change the setting. 0 [Z] SETTINGS MODULE NAVIGATI CHART - OF DISARM/UNLOCK BEFORE RELOCK AFTER RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL FIRST PRESS TAKEOVER SECURE TAKEOVER DELAY FACTORY KEYLESS RS SEQUENCE CFIGURATI 09 - Technical Support only MODULE RUN TIME WAIT TO DELAY N/A *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc.
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE ER ERROR CODES - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 Engine running. Key in ignition at position. II After a remote starter failure, the parking lights will flash three [x] times, then will flash [X] number times to indicate an error code. See table. N/A Trunk is open. Foot brake is. Hood is open. N/A Tach failure. 09 N/A 0 System is in Valet Mode. [Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE ER ERROR CODES: NOTES I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 Engine tach signal is lost. N/A II If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for.5 seconds when using a -WAY remote. OR Press once [x] on button 4 when using a -WAY remote. Foot brake is. Hood is open. Engine RPM limiter is. Glow plug timeout error. Vehicle is moving (VSS). Check engine warning light is. 09 Low fuel warning light is. REMOTE ER SHUTDOWN ERROR CODES: NOTES The parking lights will flash four [4x] times, then will flash [Y] number times to indicate an error code. See table. Automotive Data Solutions Inc. PAGE OF 8 DOC.: #8457 7
I II III DURING PROGRAMMING DURING REMOTE WITH IGNITI Automotive Data Solutions Inc. DIAGNOSTIC TEST MODULE LED STATUS MODULE DIAGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. PAGE 4 OF 8 DOC.: #8457 7
MODULE RESET PROCEDURE - OF 0 Disconnect all connectors from module except the BLACK 4-PIN connector. Reconnect all connectors. Disconnect the BLACK 4-PIN connector. Repeat programming procedure. PRESS AND HOLD programming button while connecting the BLACK 4-PIN connector. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. Wait, LED will flash RED. RELEASE programming button. LED will turn RED for seconds. Module RESET completed. Automotive Data Solutions Inc. PAGE 5 OF 8 DOC.: #8457 7
TAKEOVER PROCEDURE - STD KEY - OF All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote. Insert key into ignition. Failure to follow procedure will result in vehicle engine shutdown. PAGE 6 OF 8 DOC.: #8457 7 Turn key to position. Press and release BRAKE pedal. Take over procedure completed. Automotive Data Solutions Inc.
TAKEOVER PROCEDURE - PTS - OF All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote or request switch. STOP PAGE 7 OF 8 DOC.: #8457 7 DO NOT PRESS BRAKE PEDAL. Push start button twice [x] to position. Wait seconds for key validation. ENGINE STOP Press and release BRAKE pedal. Take over procedure completed. Failure to follow procedure will result in vehicle engine shutdown. Automotive Data Solutions Inc.
INSTALLATI CHECKLIST - OF PAGE 8 OF 8 DOC.: #8457 7 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press the LOCK button once [x] on the aftermarket keyfob. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question : Do the doors lock? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. RAP and auto light shutdown test YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 0 4 Press the UNLOCK button once [x] on the aftermarket keyfob. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Question : Do the doors unlock? Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the trunk or hatch open/unlock? Question 9: Does the vehicle remote start? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. 5 Enter vehicle and close the doors. Question 4: Does the driver side sliding door open? 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. YES: Press the AUX button once [x] to close the driver sliding door and go to next step. 7 Wait for the vehicle to start. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press brake pedal. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. YES: Go to next step. 6 YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. Question 0: Does the vehicle shut down? Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 0 Installation checklist completed. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. Automotive Data Solutions Inc.