PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE This product must be installed in accordance with the applicable code by a person familiar with the construction and operation of the product and the hazards involved. Read all of these instructions before WARNING: Disconnect power prior to servicing or 1 3 1/4-20 ROD 3/8" ~ 1/2" BELOW CEILING 3 ½ (Typ.) Install an Iberville 1 ½ deep octagon box (part # CI-54151-1/2) or equivalent. Center octagon box in position for best fixture position. CABLE COUPLER #2 Positioning of Cable Coupler #2 will be determined by the length of the PMX fixture being installed. 2 1/4-20 rod must be secured or anchored in ceiling system. (rod or anchoring to be supplied by others). Proper installation of the rod length should protrude through the ceiling approximately 3/8 to ½ Once installed and secured, cable coupler #2 can now be screwed into the rod. WALL PLATE 1/4-20 STUD INTEGRATED INTO POWER CANOPY 4 CABLE STAY SP1 POWER CANOPY CABLE COUPLER #1 3/64" AIRCRAFT CABLE POWER CORD BUSHING END GLIDERS TRANSVERSE CABLE THUMB SCREW Install wall plate, make electrical connection from power cord supplied with PMX fixture. Install power cord bushing. Mount power canopy with 4 set CSK screws provided. Install cable coupler #1 into power canopy stud. To ensure the PMX fixture is horizontally balanced, adjust transverse cable by loosen transverse cable thumb screw. Addition cable available at the end gliders. Adjust power cord tension by loosen thumb screw of cable stable. PMX-Pendant-Matrix-Install Subject to change without notice REV 2016.04.11 1/5
PMX SERIES PENDANT MOUNTED MATRIX SP2 STYLE This product must be installed in accordance with the applicable code by a person familiar with the construction and operation of the product and the hazards involved. Read all of these instructions before WARNING: Disconnect power prior to servicing or 1 3 3 ½ (Typ.) Install an Iberville 1 ½ deep octagon box (part # CI-54151-1/2) or equivalent. Center octagon box in position for best fixture position. END GLIDERS CABLE STAY To adjust length of aircraft cable and horizontal balance of fixture, adjust all four end gliders individually. additional cable available at the end glider. 2 Adjust power cord tension by loosen thumb screw of cable stable. WALL PLATE SP2 POWER CANOPY 3/64" AIRCRAFT CABLE POWER CORD BUSHING Install wall plate, make electrical connection from power cord supplied with PMX fixture. Install power cord bushing. Mount power canopy with 4 set CSK screws provided. PMX-Pendant-Matrix-Install Subject to change without notice REV 2016.04.11 2/5
CDMR 111 AR 111 PAR 36 PMX LARGE SERIES Glass Lens Option Twist lamp into GX 8.5 socket accordingly. PAR 30 CMH Attach AR111 lamp into socket provided. PAR 30 Halogen Attach PAR36 lamp into socket provided. T4 G8.5 CMH To Install an optional glass lens, twist counterclockwise to release front ring, turn ring until tabs line up & ring drops out. Install glass lens into face ring, use snap ring to hold glass in position. (Glass Lens & Snap ring ordered separately) Twist lamp into medium base socket. Place lamp between clips on adaptor ring. Twist lamp into medium base socket. Place lamp between clips on adaptor ring. Insert Bi-pin T4 lamp into socket. PMX-Pendant-Matrix-Install Subject to change without notice REV 2016.04.11 3/5
PMX SMALL SERIES MR16 GX10 CMH AR70 Glass Lens Option Push MR16 lamp into GU 5.3 (MR16 ) Socket accordingly. Place MR16 lamp into adapter ring PAR20 CMH Twist GX10 MR16 CMH lamp into GX10 Socket accordingly. Line up tabs on front ring to base ring, PAR 20 Twist AR70 Lamp into DC Bayonet base Socket provided. Line up tabs on front ring to base ring XIC LED To Install an optional glass lens, twist counterclockwise to release front ring, turn ring until tabs line up & ring drops out. Install glass lens into face ring, use snap ring to hold glass in position. (Glass Lens & Snap ring ordered separately) Twist lamp into medium base pulse rated Socket. Line up tabs on front ring to base ring, turn clockwise to secure into place. Twist lamp into medium base Socket. Release lamp holder from assembly, remove green protective film over adapter PMX-Pendant-Matrix-Install Subject to change without notice REV 2016.04.11 4/5
XIC STANDARD (ELV) DIMMING INSTRUCTION WARNING: ENSURE FIXTURE IS SWITCHED OFF BEFORE CONNECTING LED PRODUCT. FAILURE TO DO SO WILL CAUSE IMMEDIATE LED FAILURE Junction box Wiring Internal wiring within Housing (cannot be changed) CONNECT TO 120VAC OR 277V, 50/60Hz INPUT ELECTRONIC LOW VOLTAGE DIMMER (ELV) OPTIONAL NEUTRAL (WHITE) HOT LED DRIVER ELV DIMMING LED- LED- LED+ (RED) LED+ (RED) MATING CONNECTORS FOR LED XIC LED MODULE PMX-Pendant-Matrix-Install Subject to change without notice REV 2016.04.11 5/5