Alarms & Remote Start Omega R&D Inc. TL ISTALL UIDE OL-BLADE-AL(DL-TL-E Available for : OL-BLADE-AL Rev. Date: June 0, 0 Doc. o.: #### The brand names and logos found in this guide are property of their respective owners. Omega R&D Inc. 0! OTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation uide carefully before beginning any work.
Page of OL-BLADE-AL(DL-TL-E 000 Doc. o.: #### install TYPE SELECTiOn FeUReS BRAKe PeDAl STUS output e-brake output DooR STUS output TRUnK STUS output HooD STUS output* 0-0 0-0 ToYoTA 08-0 08-0 Camry (0-bit 0- Camry 0- Camry Hybrid 0- Corolla (0-bit 09-0 Corolla 09- Corolla MT 09- Highlander (0-bit 08-0 Highlander 08- Highlander Hybrid 08- Matrix (0-bit 09-0 Rav (0-bit 0-0 Rav 09- Sequoia (0-bit 08-0 Tundra (0-bit Yaris (0-bit * Available only if vehicle is equipped with factory hood switch. install TYPe TRUnK/HCH ReleASe xd (0-bit DooR UnloCK xb (0-bit DooR lock DA immobilizer BYPASS 09-0 DiSARM oem AlARM YeAR Vibe ARM oem AlARM MoDel PUSH To START CTRl MAKe 0- SCion PonTiAC ES0 TAile WinDoW ReleASe Keyless and smartkey systems will remain functional during remote start. lexus I TACHoMeTeR output OTE Omega Research & Development Inc. 0
Page of OL-BLADE-AL(DL-TL-E Doc. o.: #### 000 COMPOnEnT LOCOr A B C Omega Research & Development Inc. 0
Page of OL-BLADE-AL(DL-TL-E Doc. o.: #### 000 name TYPe PoSiTion PolARiTY MoDUle locion CoMPonenT locor 0 Red 0 Brown E 8 0 0-0 Beige 0 LtBlue E8 8 Brown 0 Ltreen 0 reen 0 Pink 09-0 E8 8 Brown Corolla TMMC 09-0 Corolla UMMI ToYoTA Highlander Matrix Rav Sequoia Tundra Yaris DeSCRiPTion Camry YeAR MoDel MAKe TYPE - wire CrOSS reference CHArT - OF 0 Ltreen 0 LtBlue 0 Red D 8 LtBlue 0 Blue 08-0 0 Beige 0 LtBlue E 8 Brown 09-0 0 Ltreen 0 reen 0 Pink E 0-0 8 Brown 0 0 Blue 0 Ltreen H 8 Orange 08-0 0 Purple 0 Blue 0 Ltreen J0 8 Ltray 0-0 0 Purple 0 Purple 0 reen 0-0 0 Purple Omega Research & Development Inc. 0
Page of OL-BLADE-AL(DL-TL-E Doc. o.: #### 000 SCion xb xd name TYPe PoSiTion PolARiTY MoDUle locion CoMPonenT locor YeAR MoDel Vibe DeSCRiPTion PonTiAC MAKe TYPE - wire CrOSS reference CHArT - OF Beige LtBlue E 8 Brown 09-0 Beige LtBlue C 8 08-0 Ltreen Ltreen Purple reen 08-0 Purple Omega Research & Development Inc. 0
Page of OL-BLADE-AL(DL-TL-E 000 Doc. o.: #### TYPE - wiring DIARAM OTE COECTOR AD PIOUT MAY VARY. PLEASE REFER TO CHART. COECTOR PARKI LIHT SWITCH PA RK I LI HT ( 0 9 8 0 9 8 REMOTE STARTER DE CO CT TX STADARD (I, ACC, START REMOTE STARTER COECTIOS TO VEHICLE ARE REQUIRED PARKI LIHT OUTPUT *BLADE COECTOR EXACT PI-OUT WHITE/RED 0 0 WHITE/BLACK WHITE 09 9 PIK/BLACK 08 8 PIK 0 BLACK BROW/RED 0 BROW/YELLOW ORAE/BLACK 0 ORAE/WHITE ORAE 0 0 BLUE/YELLOW 0 YELLOW RAY/RED 0 RAY/YELLOW WITHOUT OEM HOOD SWITCH OLY L H BLUE/RED REE/RED WHITE/BLACK (C WHITE/RED (C WHITE (C YELLOW (C BROW/RED - H BROW/YELLOW -L ORAE/BLACK - ROUD IPUT ORAE/WHITE (C ORAE (C PIK/BLACK (C PIK (C BLUE/RED (C BLUE/YELLOW (C REE/RED - CODE RAY/RED - RAY/YELLOW (C BLACK (C 8 9 0 Omega Research & Development Inc. 0
Page of OL-BLADE-AL(DL-TL-E Doc. o.: #### 000 Rav 09- TYPe PoSiTion PolARiTY MoDUle locion CoMPonenT locor 09- name Corolla UMMI 09- DeSCRiPTion ToYoTA Corolla TMMC YeAR MoDel MAKe TYPE - wire CrOSS reference CHArT - OF F 8 pin Yellow E 9 pin pin E8 8 Brown F 8 pin Red E 9 pin pin E8 8 Brown Ltreen Ltreen F 8 pin Yellow E 9 pin Red pin E 8 Brown Omega Research & Development Inc. 0
Page 8 of OL-BLADE-AL(DL-TL-E Doc. o.: #### 000 TYPE - wiring DIARAM MAI BODY FROT SIDE BACK SIDE OTE COECTOR AD PIOUT MAY VARY. PLEASE REFER TO CHART. 0 9 8 0 9 8 PA RK I LI HT ( COECTOR PARKI LIHT SWITCH 8 9 8 9 0 8 REMOTE STARTER O TI I I (+ WARI: DO OT COECT AY OTHER ACCESSORY,IITIO OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE ITERFACE MODULE IS HADLI THE REQUIRED VEHICLE POWER AD START SEQUECE FROM THE PUSH TO START BUTTO CIRCUIT. DIODE 8 9 0 00 (+ IITIO IPUT SW ST PARKI LIHT OUTPUT H L *BLADE COECTOR EXACT PI-OUT WHITE/RED 0 0 WHITE/BLACK WHITE 09 9 PIK/BLACK 08 8 PIK 0 BLACK BROW/RED 0 BROW/YELLOW ORAE/BLACK 0 ORAE/WHITE ORAE 0 BLUE/RED 0 BLUE/YELLOW REE/RED 0 YELLOW RAY/RED 0 RAY/YELLOW WHITE/BLACK - OUTPUT WHITE/RED (C WHITE - IITIO IPUT YELLOW (C BROW/RED - H BROW/YELLOW - L ORAE/BLACK - ROUD IPUT ORAE/WHITE (C ORAE (C PIK/BLACK (C PIK (C BLUE/RED - ROUD IPUT BLUE/YELLOW - OUTPUT REE/RED (C RAY/RED (C RAY/YELLOW (C BLACK (C WITHOUT OEM HOOD SWITCH OLY IMPORTAT: - O TAKEOVER AVAILABLE. UPO OPEI VEHICLE DOOR EIE WILL SHUTDOW. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. EIE START STOP 8 9 0 PT S (- COECTIOS ARE REQUIRED OLY IF IDLE MODE IS DESIRED Omega Research & Development Inc. 0
Page 9 of OL-BLADE-AL(DL-TL-E Doc. o.: #### 000 0- Highlander Highlander Hybrid 08-08- TYPe PoSiTion PolARiTY MoDUle locion CoMPonenT locor 0- ToYoTA Camry Hybrid 0- name Camry YeAR MoDel ES0 DeSCRiPTion lexus MAKe TYPE - wire CrOSS reference CHArT - OF I 0 pin 0 E 0 pin 0 Red pin 0 Blue E 8 0 Ltreen Pink I 0 pin 0 Brown E9 0 pin 0 ray pin 0 Blue E 8 0 I 0 pin 0 Brown E9 0 pin 0 ray pin 0 Blue E 8 0 I 0 pin 0 D0 0 pin 0 Pink pin 0 Pink D 8 LtBlue 0 Blue I 0 pin 0 D0 0 pin 0 Yellow pin 0 Pink D 8 LtBlue 0 Omega Research & Development Inc. 0
Page 0 of OL-BLADE-AL(DL-TL-E 000 Doc. o.: #### TYPE - wiring DIARAM MAI BODY BACK SIDE OTE COECTOR AD PIOUT MAY VARY. PLEASE REFER TO CHART. 0 9 8 0 9 8 8 9 0 PA RK I (+ SW LI ST HT ( COECTOR PARKI LIHT SWITCH 8 9 0 TI I I REMOTE STARTER (+ PARKI LIHT OUTPUT O WARI: DO OT COECT AY OTHER ACCESSORY,IITIO OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE ITERFACE MODULE IS HADLI THE REQUIRED VEHICLE POWER AD START SEQUECE FROM THE PUSH TO START BUTTO CIRCUIT. DIODE IITIO IPUT 00 8 9 0 H L *BLADE COECTOR EXACT PI-OUT WHITE/RED 0 0 WHITE/BLACK WHITE 09 9 PIK/BLACK 08 8 PIK 0 BLACK BROW/RED 0 BROW/YELLOW ORAE/BLACK 0 ORAE/WHITE ORAE 0 BLUE/RED 0 BLUE/YELLOW REE/RED 0 YELLOW RAY/RED 0 RAY/YELLOW WHITE/BLACK - OUTPUT WHITE/RED (C WHITE - IITIO IPUT YELLOW (C BROW/RED - H BROW/YELLOW - L ORAE/BLACK - ROUD IPUT ORAE/WHITE (C ORAE (C PIK/BLACK (C PIK (C BLUE/RED - ROUD IPUT BLUE/YELLOW - OUTPUT REE/RED (C REE/YELLOW (C RAY/RED (C RAY/YELLOW (C WITHOUT OEM HOOD SWITCH OLY IMPORTAT: - O TAKEOVER AVAILABLE. UPO OPEI VEHICLE DOOR EIE WILL SHUTDOW. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. EIE START STOP 8 9 0 PT S (- COECTIOS ARE REQUIRED OLY IF IDLE MODE IS DESIRED Omega Research & Development Inc. 0
Page of OL-BLADE-AL(DL-TL-E Doc. o.: #### 000 TYPe PoSiTion PolARiTY MoDUle locion CoMPonenT locor 09- name Corolla UMMI MT DeSCRiPTion 09- ToYoTA Corolla TMMC MT YeAR MoDel MAKe TYPE - wire CrOSS reference CHArT - OF F 8 pin Yellow A E 9 pin A E8 pin B E8 8 Brown Clutch A pin Clutch Switch C Clutch A pin Ltreen Clutch Switch C F 8 pin Red A E 9 pin A E8 pin B E8 8 Brown Clutch A pin Clutch Switch C Clutch A pin Ltreen Clutch Switch C Ltreen Ltreen Omega Research & Development Inc. 0
Page of OL-BLADE-AL(DL-TL-E Doc. o.: #### 000 TYPE - wiring DIARAM MAI BODY FROT SIDE BACK SIDE OTE COECTOR AD PIOUT MAY VARY. PLEASE REFER TO CHART. 0 9 8 0 9 8 PA RK I LI HT ( COECTOR PARKI LIHT SWITCH 8 9 8 9 0 8 REMOTE STARTER O TI I I (+ WARI: DO OT COECT AY OTHER ACCESSORY,IITIO OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE ITERFACE MODULE IS HADLI THE REQUIRED VEHICLE POWER AD START SEQUECE FROM THE PUSH TO START BUTTO CIRCUIT. SW ST (+ PARKI LIHT OUTPUT ROUD WHE RUI OUTPUT DIODE IITIO IPUT 00 8 9 0 H L *BLADE COECTOR EXACT PI-OUT WHITE/RED 0 0 WHITE/BLACK WHITE 09 9 PIK/BLACK 08 8 PIK 0 BLACK BROW/RED 0 BROW/YELLOW ORAE/BLACK 0 ORAE/WHITE ORAE 0 BLUE/RED 0 BLUE/YELLOW REE/RED 0 YELLOW RAY/RED 0 RAY/YELLOW WHITE/BLACK - OUTPUT WHITE/RED (C WHITE - IITIO IPUT YELLOW (C BROW/RED - H BROW/YELLOW - L ORAE/BLACK - ROUD IPUT ORAE/WHITE (C ORAE (C PIK/BLACK (C PIK (C BLUE/RED - ROUD IPUT BLUE/YELLOW - OUTPUT REE/RED (C RAY/RED - ROUD IPUT RAY/YELLOW (C BLACK (C WITHOUT OEM HOOD SWITCH OLY A - CLUTCH SWITCH 8 8 8A 8 0 IMPORTAT: - O TAKEOVER AVAILABLE. UPO OPEI VEHICLE DOOR EIE WILL SHUTDOW. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. EIE START STOP 8 9 0 PT S (- CH UT CH UT CL CL V Omega Research & Development Inc. 0
Page of OL-BLADE-AL(DL-TL-E Doc. o.: #### 000 rtridge installion Slide cartridge into unit. otice button under LED. Ready for Module Programming Procedure. TYPE - MODULE PrOgrAMMing PrOCEDUrE OTE I Insert key into ignition. LED will flash BLUE and RED. 8 Wait, LED will turn solid BLUE then will turn OFF. Turn key to OFF position. 9 Remove key. Remove key. 0 Module Programming Procedure completed. Between each step, LED will turn solid RED, this is the default standby mode. Insert key into ignition. Turn key to O position. O (If vehicle is not equipped with immobilizer, press module programming button. LED will flash BLUE once [x]. x OFF Omega Research & Development Inc. 0
Page of OL-BLADE-AL(DL-TL-E Doc. o.: #### 000 TYPE, & - MODULE PrOgrAMMing PrOCEDUrE OTE I Between each step, LED will turn solid RED, this is the default standby mode. Æ EIE START STOP Push start button twice [x] to O position. x Æ EIE START STOP x Push start button once [x] to OFF position. Module Programming Procedure completed. Wait, LED will turn solid BLUE then will turn OFF. Omega Research & Development Inc. 0
BLADE-AL XX-XX PET - PAE X-X Page of OL-BLADE-AL(DL-TL-E Doc. o.: #### 000 identify VEHiCLE notice YEAr Locate the Vehicle Identification umber (VI and identify the 0th character. Æ AYTAL8DR0X Match the VI s 0th character to its corresponding year. l > 990 S > 99 Y > 000 > 00 A > 00 M > 99 T > 99 > 00 > 00 B > 0 n > 99 V > 99 > 00 > 00 C > 0 P > 99 W > 998 > 00 8 > 008 D > 0 R > 99 X > 999 > 00 9 > 009 e > 0 MODULE DiAgnOSTiCS DiAnoSTiCS led STUS DURin PRoRAMMin DURin ReMoTe START WiTH inition off Flashing RED Missing/wrong information from firmware or vehicle Incorrectly programmed Incorrectly programmed or connected Solid RED Waiting for more vehicle information Incorrectly programmed ot programmed waiting for more vehicle information Flashing BLUE Additional steps required to complete programming Correctly programmed and operational False ground when running status from remote starter Solid BLUE then OFF Correctly programmed Reset in progress Reset in progress OFF o activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTOrY reset PrOCEDUrE DISCOECT cartridge from remote starter. PRESS AD HOLD programming button while re-connecting cartridge to remote starter. LED will flash red. Immediately RELEASE programming button. LED will turn solid red for seconds. RESET COMPLETED. RECOECT all connectors. Repeat programming procedure.! Failure to follow procedure may result with a DTC or a CHECK EIE error message. This product is protected by one or more of the following patents: U.S. LETTErS PEnT no.,9,;,0,0;,,00;,9,;,,;,9,;,,8;,9,;,9,;,9,9;,,88;,,88;,,;,8,89;,9,0;,00,0;,0,8;,0,;,0,;,08,;,0,80;,0,9;,,08;,9,9;,8,9;,89,;,0,9; nadian PEnT no.,0,8;,,0;,,0;,,99;,,0;,,0;,,08;,,0;,0,89;,,90;,,9;,,8; EUrOPEAn PEnT no.,0,8; DE 980-9T; U.S. 000; 00098; 00098; 00008; 008000; 009009; EP00; 808; 80; Omega Research & Development Inc. 0