SPECIFICATIONS 2-WAY 3-WAY EXPLOSION PROOF VALVES OPERATG CONDITIONS Media: Air, water, and other fluids, compatible with standard Buna seals. Hot water, steam, gasoline, and many oils require special seal materials. (Consult representative or factory.) Valve Temperature Range: Standard Valve-0 F(-18 C) to 104 F(40 C) ambient; 0 F (-18 C) to 1 F(65 C) media. Optional Valves can tolerate much higher or much lower ambient and media temperatures. Consult factory for specifics. Maximum Operating Pressure Differentials: See Catalog Listings Burst Pressure: 00 PSI Leakage: Bubble tight for standard valves Vacuum: To 5 Microns - Consult factory ELECTRICAL CHARACTERISTICS Coil Voltage: 5 to 8 VAC - HZ - 1.8 to 265V DC Nominal Power: Wattage A.C. 7.3 Watts D.C. 9.5 Watts Coil Construction: Molded coil and third wire ground (standard) Typical Response Time on Air: 4-16 Milliseconds MECHANICAL CHARACTERISTICS Body: Stainless steel Orifice Diameter: See catalog listings Porting: See catalog listings Housing: ¹ ₂" NPT conduit Listings: Valves are U.L. Listed and CSA Certified for Hazardous Locations Class I, Div 1, Group C and D - Class II, Div 1, Groups E, F, and G; Div 2 Groups A,B,C,D,E,F, and G. OPTIONS AVAILABLE: 3 WAY MULTI-PURPOSE FOR ILLUSTRATED OPTIONS SEE PAGES 76-81 FOR FLOW CHARTS SEE PAGES 95-97 HOUSG OPTIONS see page 78 MOUNTG BRACKET COIL OPTIONS see page 79 MOLDED COIL Standard POTTED COIL & HOUSG All models HIGH TEMPERATURE MOLDED COIL THIRD WIRE GROUND BODY OPTIONS see page 80 FE METERG METERG TO ¹ ₈" ORIFICE METERG TO ¹ ₄" ORIFICE Models E22, E23 METERED BYPASS Models E22, E23 MANUAL OVERRIDE * METERED EXHAUST PORT Model E23 PORT OPTIONS see page 81 BOTTOM ORIFICE PORT Models E22, E23 BOTTOM CAVITY PORT Models E22, E23 PORT 90 LEFT Models E22, E23 MANIFOLD MOUNT Models E22, E23 FLANGE MOUNT Models E22, E23 PORT 90 RIGHT Models E22, E23 2-WAY & 3-WAY EXPLOSION PROOF MISCELLANEOUS Options see page 76 SILVER SHADG RG ALUMUM SHADG RG BUILT MUFFLER Note: Availability of certain options or combination of options may vary with quantity of units ordered consult representative or factory. * Not available over 2 psi Not available in ¹ ₄" orifice x. (6.4) DEEP. x. (6.4) DEEP. x. (6.4) DEEP.
DE- OUT OUT DE- OUT OUT DE- SERIES MODEL E21 2-WAY NORMALLY OPEN CONDUIT HOUSG (700) 235 (0) 1 (3) (1) (700) 235 (0) 1 (3) (1).024.053.095.227 E21G7XCCM E21H7XCCM E21J7XCCM E21K7XCCM E21N7XCCM SERIES MODEL E22 2-WAY NORMALLY CLOSED SERIES MODEL E23 3-WAY NORMALLY CLOSED EXHAUST TO ATMOSPHERE E21G9ZCCM E21H9ZCCM E21J9ZCCM E21K9ZCCM E21N9ZCCM CONDUIT HOUSG 0 2 (0) 0 () 1 (0) (0) 0 2 (0) 0 () 1 (2) (0) 5 1 (0) (135) (135) () (70) 15 15 SOLENOID VALVES... 1 (0) (135) (135) () (70) VALVES WITH SLEEVE ORIFICE ARE NOT UL NOR CSA LISTED 5/32 3/16 1/4.024.052.095.284.404.0.700 LET EXH. LET EXH. 3/16 3/16 1/4 1/4.024.024.052.095.095.095.095.284.284.227.0.0.227.700.700.227 E22G7DCCM E22H7DCCM E22J7DCCM E22K7DCCM E22N7DCCM E22O7DCCM E22P7DCCM E22R7DCCM E22G9DCCM E22H9DCCM E22J9DCCM E22K9DCCM E22N9DCCM E22O9DCCM E22P9DCCM E22R9DCCM CONDUIT HOUSG E23GG7DCCM E23HJ7DCCM E23JJ7DCCM E23JK7DCCM E23KK7DCCM E23NK7DCCM E23NN7DCCM E23PK7DCCM E23PN7DCCM E23RK7DCCM E23RN7DCCM E23GG9DCCM E23HJ9DCCM E23JJ9DCCM E23JK9DCCM E23KK9DCCM E23NK9DCCM E23NN9DCCM E23PK9DCCM E23PN9DCCM E23RK9DCCM E23RN9DCCM VALVES WITH SLEEVE ORIFICE ARE NOT UL NOR CSA LISTED Ratings in brackets are optional extended ratings; consult factory When ordering add voltage and frequency to complete valve number. Example: (E23GG7DCCM-/) NOTE: The above checked ( ) Valves, but with optional molded coils, are most popular based on sales and likely to be in Distributor stock.
SPECIFICATIONS 3-WAY EXPLOSION PROOF VALVES OPERATG CONDITIONS Media: Air, water, and other fluids, compatible with standard Buna seals. Hot water, steam, gasoline, and many oils require special seal materials - Consult representative or factory. Valve Temperature Range: 0 F ( -18 C) to a maximum of 221 F (105 C) including coil heat rise, ambient and media temperatures. Other temperature ranges available on request along with specific application parameter information specified. Maximum Operating Pressure Differentials: See Catalog Listings Burst Pressure: 00 PSI Leakage: Bubble tight for standard valves Vacuum: To 5 Microns - Consult factory ELECTRICAL CHARACTERISTICS Coil Voltage: 5 to 8 VAC - HZ - 1.8 to 265V DC Nominal Power: Wattage A.C. 7.3 Watts D.C. 9.5 Watts Coil Construction: Molded coil and third wire ground (standard) Typical Response Time on Air: 4-16 Milliseconds MECHANICAL CHARACTERISTICS Body: Stainless steel Orifice Diameter: See catalog listings Porting: See catalog listings Housing: ¹ ₂" NPT conduit Listings: Valves are U.L. Listed and CSA Certified for Hazardous Locations Class I, Div 1, Group C and D - Class II, Div 1, Groups E, F, and G; Div 2 Groups A,B,C,D,E,F, AND G. OPTIONS AVAILABLE 3-WAY EXPLOSION PROOF FOR ILLUSTRATED OPTIONS SEE PAGES 76-81 FOR FLOW CHARTS SEE PAGES 95-97 HOUSG OPTIONS see page 78 MOUNTG BRACKET COIL OPTIONS see page 79 MOLDED COIL Standard POTTED COIL & HOUSG All models HIGH TEMPERATURE MOLDED COIL BODY OPTIONS see page 80 METERG TO ¹ ₈" ORIFICE METERG TO ¹ ₄" ORIFICE Models E23 METERED BYPASS Models E23, E, E26 MANUAL OVERRIDE * METERED EXHAUST PORT Model E23, E, E26 PORT OPTIONS see page 81 BOTTOM ORIFICE PORT BOTTOM CAVITY PORT Models E23, E24, E, E26 PORT 90 LEFT MANIFOLD MOUNT Models E23, E24, E, E26 FLANGE MOUNT Models E23, E24, E, E26 PORT 90 RIGHT 3-WAY EXPLOSION PROOF MISCELLANEOUS Options see page 76 SILVER SHADG RG ALUMUM SHADG RG BUILT MUFFLER Note: Availability of certain options or combination of options may vary with quantity of units ordered consult representative or factory. * Not available over 2 psi Not available in ¹ ₄" orifice x. (6.4) DEEP. x. (6.4) DEEP. x. (6.4) DEEP. x. (6.4) DEEP.
DE- EXH. EXH. DE- EXH. EXH. DE- N.C. N.O. N.C. N.O. DE- N.O. N.C. COM. N.C. COM. SERIES MODEL E23 3-WAY NORMALLY CLOSED PIPED EXHAUST 1 (0) (135) (135) () (70) 15 15 1 (0) (135) (135) () (70) 1 (2) (1) (1) (90) 1 0 235 () 0 (2) 1 (2) (1) (1) 1 35 LET EXH. LET EXH. 3/16 3/16 1/4 1/4.024.024.052.095.095.095.095.284.284.227.0.0.227.700.700.227 CONDUIT HOUSG E23GG7XCCM E23HJ7XCCM E23JJ7XCCM E23JK7XCCM E23KK7XCCM E23NK7XCCM E23NN7XCCM E23PK7XCCM E23PN7XCCM E23RK7XCCM E23RN7XCCM SERIES MODEL E24 3-WAY NORMALLY OPEN LET EXH. LET EXH..024.024.052.095.095.095.095.284.284.227.284 E23GG9ZCCM E23HJ9ZCCM E23JJ9ZCCM E23JK9ZCCM E23KK9ZCCM E23NK9ZCCM E23NN9ZCCM E23PK9ZCCM E23PN9ZCCM E23RK9ZCCM E23RN9ZCCM CODUIT HOUSG E24GG7XCCM E24HJ7XCCM E24JJ7XCCM E24JN7XCCM E24KN7XCCM E24NN7XCCM SERIES MODEL E 3-WAY DIRECTIONAL CONTROL 0 235 (0) 0 (0) 1 (0) (1) MAX. OPER. SOLENOID VALVES... 1 35 VALVES WITH SLEEVE ORIFICE ARE NOT UL NOR CSA APPROVED VALVES WITH SLEEVE ORIFICE ARE NOT UL NOR CSA APPROVED LET EXH. LET EXH. * * * * * * *.024*.024.052*.052.095*.052.095*.095 *.284*.284*.227 E24GG9ZCCM E24HJ9ZCCM E24JJ9ZCCM E24JN9ZCCM E24KN9ZCCM E24NN97CCM CODUIT HOUSG EGG7XCCM EHH7XCCM EJH7XCCM EJJ7XCCM EKK7XCCM ENK7XCCM ENN7XCCM VALVES WITH SLEEVE ORIFICE ARE NOT UL NOR CSA APPROVED SERIES MODEL E26 3-WAY MULTI-PURPOSE N.O. LET EXH. LET EXH. * * * * *.024*.024.052*.052.095*.095 *.284*.277 EGG9ZCCM EHH9ZCCM EJH9ZCCM EJJ9ZCCM EKK9ZCCM ENK9ZCCM ENN9CCM CODUIT HOUSG E26GG7XCCM E26HH7XCCM E26JJ7XCCM E26KK7XCCM E26NN7XCCM E26GG9ZCCM E26HH9ZCCM E26JJ9ZCCM E26KK9ZCCM E26NN9ZCCM VALVES WITH SLEEVE ORIFICE ARE NOT UL NOR CSA APPROVED * Orifice Ratings in brackets are optional extended ratings; consult factory When ordering add voltage and frequency to complete valve number. Example: (E26GG7XCCM-/) NOTE: The above checked ( ) Valves are most popular based on sales and likely to be in Distributor stock.
SERIES E MIATURE EXPLOSION PROOF VALVES! Meet today s demands for economy of space and energy consumption. For hazardous locations. APPLICATION: General purpose or safety valves for pneumatic and hydraulic applications. The versatility of these valves is increased to include the handling of hot air, hot water, refrigerants and many other media, by the use of different seals. SPECIFICATIONS OPERATG CONDITIONS Media: Air and other fluids, compatible with standard Buna seals. Hot water, steam, gasoline, oils, some hydraulic fluids, and many other media require special seal materials - Consult representative or factory. Valve Temperature Range: Standard Valves - 0 F ( 18 C) to 104 F (40 C) ambient; 0 F ( 18 C) to 1 F (65 C) media. Optional Valves - can tolerate much higher or much lower ambient and media temperatures. Consult factory for specifications. Maximum Operating Pressure Differentials: See catalog listings Burst Pressure: 00 PSI Leakage: Bubble tight for standard valves Vacuum: To 5 Microns - Consult factory ELECTRICAL CHARACTERISTICS Coil Voltage: 5.4 to 5 VAC - HZ. 3.0 to 0 VDC. All standard voltages (U.S. & Export) carried in stock. Special voltages readily produced on order. Nominal Power: A.C. VALVES 2 WNC & 2 WNO D.C. Valves Valves Valves 7.2 Watts 4.0 Watts 5.6Watts Coil Construction: Standard, Molded with 24 leads. For Non-molded construction consult Factory. Typical Response Time on Air: 4-16 Milliseconds Operating Speed: Up to 0 CPM Duty Cycle: Continuous or Intermittent MECHANICAL CHARACTERISTICS Material: All interior parts are stainless steel Orifice Diameter: See catalog listings Porting: ¹ ₈ NPT Housing: Explosionproof construction with ¹ ₂ NPT conduit connection and third wire ground. Available in stainless steel (consult factory) Listings: Valves are U.L. Listed and CSA Certified for Hazardous Locations Class I, Div 1, Group C and D - Class II, Div 1, Groups E, F, and G; Div 2 Groups A,B,C,D,E,F, and G. Life expectancy: Millions of cycles, depending on application, lubrication, etc. Valve Weight: Only.65 lbs average Repair Packs: Consult Factory OPTIONS: Also available in all stainless steel construction Metering, bottom orifice or cavity porting, manifold mount, built in muffler, universal mounting bracket, potted coil, Class H molded coil. FOR FLOW CHARTS SEE PAGES 95-97 MIATURE EXPLOSION-PROOF SOLENOID VALVE OPERATORS A complete line of valve operators for O.E.M. applications are offered for those who wish to incorporate them in their own product line. Full technical information and details are available from Coast Pneumatics. 1 (36.5) 2.39 (.7) WITH SLEEVE PORT ADAPTER.. 3/4-32 UN TH D NPT 2 PLACES NPT NPT (2) PLC.. 1.00 (.4) NPT.27 (6.7) 1.00 (.4) Operator 1.61 (40.9) 2 WAY OR 3WAY FREE EXHAUST.73 WITHOUT SLEEVE (18.7) PORT ADAPTER. 2.48 (63.0) 1.64.89 (41.7) (22.6) 1 (36.6) #8-32 UNC TH D x.23 (5.8) DEEP. 2-Way and 3-Way Exhaust to Atmosphere..89 (22.6) 1 (36.6) 1.64 (41.7) 3.27 (83.1) #8-32 UNC TH D x.23 (5.8) DEEP. 2PLACES AS SHOWN. 3-Way Piped Exhaust
MODEL TYPE MODEL E51 Open MODEL E52 MODEL E53 Exhaust To Atmosphere MODEL E53 Piped Exhaust MODEL E54 Open MODEL E55 Directional Control MODEL E56 Multi-Purpose Control SOLENOID VALVES... FLOW CONFIGURATION VALVE NO. E51G8XCCM E51H8XCCM E51J8XCCM E51K8XCCM E52G8DCCM E52H8DCCM E52J8DCCM E52K8DCCM E52N8DCCM E53GG8DCCM E53HH8DCCM E53HJ8DCCM E53JJ8DCCM E53KJ8DCCM E53KK8DCCM E53NJ8DCCM E53NK8DCCM E53GG8XCCM E53HH8XCCM E53HJ8XCCM E53JJ8XCCM E53KJ8XCCM E53KK8XCCM E53NJ8XCCM E53NK8XCCM E54GG8XCCM E54HH8XCCM E54JJ8XCCM E54JK8XCCM E54KK8XCCM E54JN8XCCM E54KN8XCCM E55GG8XCCM E55HH8XCCM E55JJ8XCCM E55KJ8XCCM E55KK8XCCM E55NJ8XCCM E55NK8XCCM E56GG8XCCM E56HHXCCM E56JJ8XCCM E56KK8XCCM MAXIMUM OPERATG PRESSURE DIFFERENTIAL * closed orifice - in these model numbers For sleeve orifice consult factory (not UL or CSA listed) Pressure rating may change due to the viscosity of the liquid - consult factory for de-rating. NOTE: The above checked ( ) Valves are most popular based on sales and likely to be in Distributor stock. ORIFICE SIZE CV FACTOR LET EXHAUST LET EXHAUST 0.0 0 1 40 40.1 0 0 0 1 1 0 1 1 1 1 40 0 0 65 45 1 65 2 1 45 0 1 1 0 1 1 1 1 45 0 40 1 * * * * * * * * * * *.2.2.2.2.2.0 * * * * *.2*.2* * * * *.0 0.2.2.0.06.0
SERIES EL MIATURE EXPLOSION PROOF VALVES (1.8 WATTS AC AND DC) SERIES ELL MIATURE EXPLOSION PROOF VALVES (.85 WATTS DC) Meet today s demands for economy of space and energy consumption. For hazardous locations. APPLICATION: General purpose or safety valves for pneumatic and hydraulic applications. The versatility of these valves is increased to include the handling of hot air, hot water, refrigerants and many other media, by the use of different inserts. SPECIFICATIONS OPERATG CONDITIONS Media: Air and other common gases, common refrigerants except ammonia, city gas supplied by public utilities, Nos. 1 and 2 fuel oils, oils having viscosities not more than 40, SU at F, steam, some hydraulic and water or other aqueous non-flammable liquids. Some media require special seal material - Consult Factory. Valve Temperature Range: Standard Valves - 0 F ( 18 C) to 104 F (40 C) ambient; 0 F ( 18 C) to 1 F (65 C) media. Optional Valves - can tolerate much higher or much lower ambient and media temperatures. Consult factory for specifications. Maximum Operating Pressure Differentials: See table listings Burst Pressure: 0 PSI Leakage: Bubble tight for standard valves Vacuum: To 5 Microns - Consult factory ELECTRICAL CHARACTERISTICS Coil Voltage: 5- V DC 12-240 V HZ. All standard voltages carried in stock. Other voltages readily produced on order. Nominal Power: EL 1.8 watts AC and DC ELL.85 watts DC Coil Construction: Nonmolded coil, Molded with 24 leads. Molded coil potted inside housing. ALSO MOLDED CLASS H COIL. Typical Response Time on Air: 4-16 Milliseconds Operating Speed: Up to 0 CPM Duty Cycle: Continuous or Intermittent MECHANICAL CHARACTERISTICS Material: All interior parts are stainless steel Orifice Diameter: See table listings Porting: ¹ ₈ PTF ¹ ₈ NTP - available (consult factory) Housing: Explosionproof construction with ¹ ₂ NPT conduit connection. Available in stainless steel (consult factory) Listings: Valves are U.L. Listed and CSA Certified for Hazardous Locations Class I, Div 1, Group C and D - Class II, Div 1, Groups E, F, and G; Div 2 Groups A,B,C,D,E,F, and G. Life expectancy: Millions of cycles, depending on application, lubrication, etc. Valve Weight: Only.65 lbs average Repair Packs: Consult Factory OPTIONS: Metering, bottom orifice or cavity porting, built in muffler, universal mounting bracket, potted coil, Class H molded coil. Third wire ground available on request. FOR FLOW CHARTS SEE PAGES 95-97 MIATURE EXPLOSION-PROOF SOLENOID VALVE OPERATORS A complete line of valve operators for O.E.M. applications are offered for those who wish to incorporate them in their own product line. Full technical information and details are available from Coast Pneumatics. 1 (36.5) 2.39 (.7) WITH SLEEVE PORT ADAPTER.. 3/4-32 UN TH D NPT 2 PLACES NPT NPT (2) PLC.. 1.00 (.4) NPT.27 (6.7) 1.00 (.4) Operator 1.61 (40.9) 2 WAY OR 3WAY FREE EXHAUST.73 WITHOUT SLEEVE (18.7) PORT ADAPTER. 2.48 (63.0) 1.64.89 (41.7) (22.6) 1 (36.6) #8-32 UNC TH D x.23 (5.8) DEEP. and 3-Way Exhaust to Atmosphere..89 (22.6) 1 (36.6) 1.64 (41.7) 3.27 (83.1) #8-32 UNC TH D x.23 (5.8) DEEP. 2PLACES AS SHOWN. 3-Way Piped Exhaust
MODEL TYPE MODEL EL51 Open MODEL EL52 MODEL EL53 Exhaust To Atmosphere MODEL EL53 Piped Exhaust MODEL TYPE MODEL ELL52 MODEL ELL53 Exhaust To Atmosphere MODEL ELL53 Piped Exhaust SOLENOID VALVES... FLOW CONFIGURATION FLOW CONFIGURATION VALVE NO. EL51G8XCM EL51H8XCM EL51J8XCM EL52G8DCM EL52H8DCM EL52J8DCM EL53GG8DCM EL53GH8DCM EL53HH8DCM EL53JJ8DCM EL53GG8XCM EL53GH8XCM EL53HH8XCM EL53JJ8XCM Series EL MAXIMUM OPERATG PRESSURE DIFFERENTIAL ORIFICE SIZE CV FACTOR LET EXHAUST LET EXHAUST 0 0.0 80 80 Series ELL Explosion Proof Valve Numbers VALVE NO. MAXIMUM OPERATG PRESSURE DIFFERENTIAL GAS ONLY ORIFICE SIZE.0 CV FACTOR DC LET EXHAUST LET EXHAUST ELL52G8DCCM ELL53GG8DCCM ELL53GG8XCCM Pressure rating may change due to the viscosity of the liquid - consult factory for de-rating.